[net-next PATCH v3 1/5] net: dsa: tag_qca: return early if dev is not found

[net-next PATCH v3 1/5] net: dsa: tag_qca: return early if dev is not found

[Christian Marangi]

Currently checksum is recalculated and dsa tag stripped even if we later
don't find the dev.

To improve code, exit early if we don't find the dev and skip additional
operation on the skb since it will be freed anyway.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
---
changes v2:
- Add review tag

 net/dsa/tag_qca.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/net/dsa/tag_qca.c b/net/dsa/tag_qca.c
index e757c8de06f1..e5ff7c34e577 100644
--- a/net/dsa/tag_qca.c
+++ b/net/dsa/tag_qca.c
@@ -75,10 +75,6 @@ static struct sk_buff *qca_tag_rcv(struct sk_buff *skb, struct net_device *dev)
 		return NULL;
 	}
 
-	/* Remove QCA tag and recalculate checksum */
-	skb_pull_rcsum(skb, QCA_HDR_LEN);
-	dsa_strip_etype_header(skb, QCA_HDR_LEN);
-
 	/* Get source port information */
 	port = FIELD_GET(QCA_HDR_RECV_SOURCE_PORT, hdr);
 
@@ -86,6 +82,10 @@ static struct sk_buff *qca_tag_rcv(struct sk_buff *skb, struct net_device *dev)
 	if (!skb->dev)
 		return NULL;
 
+	/* Remove QCA tag and recalculate checksum */
+	skb_pull_rcsum(skb, QCA_HDR_LEN);
+	dsa_strip_etype_header(skb, QCA_HDR_LEN);
+
 	return skb;
 }
 
-- 
2.40.1

[net-next PATCH v3 2/5] net: dsa: qca8k: make learning configurable and keep off if standalone

[Christian Marangi]

Address learning should initially be turned off by the driver for port
operation in standalone mode, then the DSA core handles changes to it
via ds->ops->port_bridge_flags().

Currently this is not the case for qca8k where learning is enabled
unconditionally in qca8k_setup for every user port.

Handle ports configured in standalone mode by making the learning
configurable and not enabling it by default.

Implement .port_pre_bridge_flags and .port_bridge_flags dsa ops to
enable learning for bridge that request it and tweak
.port_stp_state_set to correctly disable learning when port is
configured in standalone mode.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
---
changes v2:
- Add review tag
- Change qca8k_port_bridge_flags to be more explicit with flag handling
  as suggested by Vladimir

 drivers/net/dsa/qca/qca8k-8xxx.c   |  7 +++--
 drivers/net/dsa/qca/qca8k-common.c | 48 ++++++++++++++++++++++++++++++
 drivers/net/dsa/qca/qca8k.h        |  6 ++++
 3 files changed, 58 insertions(+), 3 deletions(-)

diff --git a/drivers/net/dsa/qca/qca8k-8xxx.c b/drivers/net/dsa/qca/qca8k-8xxx.c
index ae088a4df794..31552853fdd4 100644
--- a/drivers/net/dsa/qca/qca8k-8xxx.c
+++ b/drivers/net/dsa/qca/qca8k-8xxx.c
@@ -1870,9 +1870,8 @@ qca8k_setup(struct dsa_switch *ds)
 			if (ret)
 				return ret;
 
-			/* Enable ARP Auto-learning by default */
-			ret = regmap_set_bits(priv->regmap, QCA8K_PORT_LOOKUP_CTRL(i),
-					      QCA8K_PORT_LOOKUP_LEARN);
+			ret = regmap_clear_bits(priv->regmap, QCA8K_PORT_LOOKUP_CTRL(i),
+						QCA8K_PORT_LOOKUP_LEARN);
 			if (ret)
 				return ret;
 
@@ -1978,6 +1977,8 @@ static const struct dsa_switch_ops qca8k_switch_ops = {
 	.port_change_mtu	= qca8k_port_change_mtu,
 	.port_max_mtu		= qca8k_port_max_mtu,
 	.port_stp_state_set	= qca8k_port_stp_state_set,
+	.port_pre_bridge_flags	= qca8k_port_pre_bridge_flags,
+	.port_bridge_flags	= qca8k_port_bridge_flags,
 	.port_bridge_join	= qca8k_port_bridge_join,
 	.port_bridge_leave	= qca8k_port_bridge_leave,
 	.port_fast_age		= qca8k_port_fast_age,
diff --git a/drivers/net/dsa/qca/qca8k-common.c b/drivers/net/dsa/qca/qca8k-common.c
index 13b8452ce5b2..fce04ce12cf9 100644
--- a/drivers/net/dsa/qca/qca8k-common.c
+++ b/drivers/net/dsa/qca/qca8k-common.c
@@ -565,9 +565,26 @@ int qca8k_get_mac_eee(struct dsa_switch *ds, int port,
 	return 0;
 }
 
+static int qca8k_port_configure_learning(struct dsa_switch *ds, int port,
+					 bool learning)
+{
+	struct qca8k_priv *priv = ds->priv;
+
+	if (learning)
+		return regmap_set_bits(priv->regmap,
+				       QCA8K_PORT_LOOKUP_CTRL(port),
+				       QCA8K_PORT_LOOKUP_LEARN);
+	else
+		return regmap_clear_bits(priv->regmap,
+					 QCA8K_PORT_LOOKUP_CTRL(port),
+					 QCA8K_PORT_LOOKUP_LEARN);
+}
+
 void qca8k_port_stp_state_set(struct dsa_switch *ds, int port, u8 state)
 {
+	struct dsa_port *dp = dsa_to_port(ds, port);
 	struct qca8k_priv *priv = ds->priv;
+	bool learning = false;
 	u32 stp_state;
 
 	switch (state) {
@@ -582,8 +599,11 @@ void qca8k_port_stp_state_set(struct dsa_switch *ds, int port, u8 state)
 		break;
 	case BR_STATE_LEARNING:
 		stp_state = QCA8K_PORT_LOOKUP_STATE_LEARNING;
+		learning = dp->learning;
 		break;
 	case BR_STATE_FORWARDING:
+		learning = dp->learning;
+		fallthrough;
 	default:
 		stp_state = QCA8K_PORT_LOOKUP_STATE_FORWARD;
 		break;
@@ -591,6 +611,34 @@ void qca8k_port_stp_state_set(struct dsa_switch *ds, int port, u8 state)
 
 	qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port),
 		  QCA8K_PORT_LOOKUP_STATE_MASK, stp_state);
+
+	qca8k_port_configure_learning(ds, port, learning);
+}
+
+int qca8k_port_pre_bridge_flags(struct dsa_switch *ds, int port,
+				struct switchdev_brport_flags flags,
+				struct netlink_ext_ack *extack)
+{
+	if (flags.mask & ~BR_LEARNING)
+		return -EINVAL;
+
+	return 0;
+}
+
+int qca8k_port_bridge_flags(struct dsa_switch *ds, int port,
+			    struct switchdev_brport_flags flags,
+			    struct netlink_ext_ack *extack)
+{
+	int ret;
+
+	if (flags.mask & BR_LEARNING) {
+		ret = qca8k_port_configure_learning(ds, port,
+						    flags.val & BR_LEARNING);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
 }
 
 int qca8k_port_bridge_join(struct dsa_switch *ds, int port,
diff --git a/drivers/net/dsa/qca/qca8k.h b/drivers/net/dsa/qca/qca8k.h
index c5cc8a172d65..8f88b7db384d 100644
--- a/drivers/net/dsa/qca/qca8k.h
+++ b/drivers/net/dsa/qca/qca8k.h
@@ -522,6 +522,12 @@ int qca8k_get_mac_eee(struct dsa_switch *ds, int port, struct ethtool_eee *e);
 
 /* Common bridge function */
 void qca8k_port_stp_state_set(struct dsa_switch *ds, int port, u8 state);
+int qca8k_port_pre_bridge_flags(struct dsa_switch *ds, int port,
+				struct switchdev_brport_flags flags,
+				struct netlink_ext_ack *extack);
+int qca8k_port_bridge_flags(struct dsa_switch *ds, int port,
+			    struct switchdev_brport_flags flags,
+			    struct netlink_ext_ack *extack);
 int qca8k_port_bridge_join(struct dsa_switch *ds, int port,
 			   struct dsa_bridge bridge,
 			   bool *tx_fwd_offload,
-- 
2.40.1

[net-next PATCH v3 3/5] net: dsa: qca8k: limit user ports access to the first CPU port on setup

[Christian Marangi]

In preparation for multi-CPU support, set CPU port LOOKUP MEMBER outside
the port loop and setup the LOOKUP MEMBER mask for user ports only to
the first CPU port.

This is to handle flooding condition where every CPU port is set as
target and prevent packet duplication for unknown frames from user ports.

Secondary CPU port LOOKUP MEMBER mask will be setup later when
port_change_master will be implemented.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
---
changes v2:
- Add review tag

 drivers/net/dsa/qca/qca8k-8xxx.c | 14 ++++++--------
 1 file changed, 6 insertions(+), 8 deletions(-)

diff --git a/drivers/net/dsa/qca/qca8k-8xxx.c b/drivers/net/dsa/qca/qca8k-8xxx.c
index 31552853fdd4..6286a64a2fe3 100644
--- a/drivers/net/dsa/qca/qca8k-8xxx.c
+++ b/drivers/net/dsa/qca/qca8k-8xxx.c
@@ -1850,18 +1850,16 @@ qca8k_setup(struct dsa_switch *ds)
 	if (ret)
 		return ret;
 
+	/* CPU port gets connected to all user ports of the switch */
+	ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(cpu_port),
+			QCA8K_PORT_LOOKUP_MEMBER, dsa_user_ports(ds));
+	if (ret)
+		return ret;
+
 	/* Setup connection between CPU port & user ports
 	 * Configure specific switch configuration for ports
 	 */
 	for (i = 0; i < QCA8K_NUM_PORTS; i++) {
-		/* CPU port gets connected to all user ports of the switch */
-		if (dsa_is_cpu_port(ds, i)) {
-			ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
-					QCA8K_PORT_LOOKUP_MEMBER, dsa_user_ports(ds));
-			if (ret)
-				return ret;
-		}
-
 		/* Individual user ports get connected to CPU port only */
 		if (dsa_is_user_port(ds, i)) {
 			ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
-- 
2.40.1

[net-next PATCH v3 4/5] net: dsa: qca8k: move qca8xxx hol fixup to separate function

[Christian Marangi]

Move qca8xxx hol fixup to separate function to tidy things up and to
permit using a more efficent loop in future patch.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
 drivers/net/dsa/qca/qca8k-8xxx.c | 78 +++++++++++++++++---------------
 1 file changed, 42 insertions(+), 36 deletions(-)

diff --git a/drivers/net/dsa/qca/qca8k-8xxx.c b/drivers/net/dsa/qca/qca8k-8xxx.c
index 6286a64a2fe3..81c6fab0a01b 100644
--- a/drivers/net/dsa/qca/qca8k-8xxx.c
+++ b/drivers/net/dsa/qca/qca8k-8xxx.c
@@ -1756,6 +1756,46 @@ static int qca8k_connect_tag_protocol(struct dsa_switch *ds,
 	return 0;
 }
 
+static void qca8k_setup_hol_fixup(struct qca8k_priv *priv, int port)
+{
+	u32 mask;
+
+	switch (port) {
+	/* The 2 CPU port and port 5 requires some different
+	 * priority than any other ports.
+	 */
+	case 0:
+	case 5:
+	case 6:
+		mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) |
+			QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) |
+			QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x4) |
+			QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x4) |
+			QCA8K_PORT_HOL_CTRL0_EG_PRI4(0x6) |
+			QCA8K_PORT_HOL_CTRL0_EG_PRI5(0x8) |
+			QCA8K_PORT_HOL_CTRL0_EG_PORT(0x1e);
+		break;
+	default:
+		mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) |
+			QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) |
+			QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x6) |
+			QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x8) |
+			QCA8K_PORT_HOL_CTRL0_EG_PORT(0x19);
+	}
+	regmap_write(priv->regmap, QCA8K_REG_PORT_HOL_CTRL0(port), mask);
+
+	mask = QCA8K_PORT_HOL_CTRL1_ING(0x6) |
+	       QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN |
+	       QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN |
+	       QCA8K_PORT_HOL_CTRL1_WRED_EN;
+	regmap_update_bits(priv->regmap, QCA8K_REG_PORT_HOL_CTRL1(port),
+			   QCA8K_PORT_HOL_CTRL1_ING_BUF_MASK |
+			   QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN |
+			   QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN |
+			   QCA8K_PORT_HOL_CTRL1_WRED_EN,
+			   mask);
+}
+
 static int
 qca8k_setup(struct dsa_switch *ds)
 {
@@ -1895,42 +1935,8 @@ qca8k_setup(struct dsa_switch *ds)
 		 * missing settings to improve switch stability under load condition.
 		 * This problem is limited to qca8337 and other qca8k switch are not affected.
 		 */
-		if (priv->switch_id == QCA8K_ID_QCA8337) {
-			switch (i) {
-			/* The 2 CPU port and port 5 requires some different
-			 * priority than any other ports.
-			 */
-			case 0:
-			case 5:
-			case 6:
-				mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) |
-					QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) |
-					QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x4) |
-					QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x4) |
-					QCA8K_PORT_HOL_CTRL0_EG_PRI4(0x6) |
-					QCA8K_PORT_HOL_CTRL0_EG_PRI5(0x8) |
-					QCA8K_PORT_HOL_CTRL0_EG_PORT(0x1e);
-				break;
-			default:
-				mask = QCA8K_PORT_HOL_CTRL0_EG_PRI0(0x3) |
-					QCA8K_PORT_HOL_CTRL0_EG_PRI1(0x4) |
-					QCA8K_PORT_HOL_CTRL0_EG_PRI2(0x6) |
-					QCA8K_PORT_HOL_CTRL0_EG_PRI3(0x8) |
-					QCA8K_PORT_HOL_CTRL0_EG_PORT(0x19);
-			}
-			qca8k_write(priv, QCA8K_REG_PORT_HOL_CTRL0(i), mask);
-
-			mask = QCA8K_PORT_HOL_CTRL1_ING(0x6) |
-			QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN |
-			QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN |
-			QCA8K_PORT_HOL_CTRL1_WRED_EN;
-			qca8k_rmw(priv, QCA8K_REG_PORT_HOL_CTRL1(i),
-				  QCA8K_PORT_HOL_CTRL1_ING_BUF_MASK |
-				  QCA8K_PORT_HOL_CTRL1_EG_PRI_BUF_EN |
-				  QCA8K_PORT_HOL_CTRL1_EG_PORT_BUF_EN |
-				  QCA8K_PORT_HOL_CTRL1_WRED_EN,
-				  mask);
-		}
+		if (priv->switch_id == QCA8K_ID_QCA8337)
+			qca8k_setup_hol_fixup(priv, i);
 	}
 
 	/* Special GLOBAL_FC_THRESH value are needed for ar8327 switch */
-- 
2.40.1

[net-next PATCH v3 5/5] net: dsa: qca8k: use dsa_for_each macro instead of for loop

[Christian Marangi]

Convert for loop to dsa_for_each macro to save some redundant write on
unconnected/unused port and tidy things up.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
---
changes v3:
- Fix compilation error with unfinished patch in v2

 drivers/net/dsa/qca/qca8k-8xxx.c | 107 ++++++++++++++++---------------
 1 file changed, 54 insertions(+), 53 deletions(-)

diff --git a/drivers/net/dsa/qca/qca8k-8xxx.c b/drivers/net/dsa/qca/qca8k-8xxx.c
index 81c6fab0a01b..f8a573679101 100644
--- a/drivers/net/dsa/qca/qca8k-8xxx.c
+++ b/drivers/net/dsa/qca/qca8k-8xxx.c
@@ -1800,7 +1800,8 @@ static int
 qca8k_setup(struct dsa_switch *ds)
 {
 	struct qca8k_priv *priv = ds->priv;
-	int cpu_port, ret, i;
+	struct dsa_port *dp;
+	int cpu_port, ret;
 	u32 mask;
 
 	cpu_port = qca8k_find_cpu_port(ds);
@@ -1855,27 +1856,27 @@ qca8k_setup(struct dsa_switch *ds)
 		dev_warn(priv->dev, "mib init failed");
 
 	/* Initial setup of all ports */
-	for (i = 0; i < QCA8K_NUM_PORTS; i++) {
+	dsa_switch_for_each_port(dp, ds) {
 		/* Disable forwarding by default on all ports */
-		ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
+		ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(dp->index),
 				QCA8K_PORT_LOOKUP_MEMBER, 0);
 		if (ret)
 			return ret;
+	}
 
-		/* Enable QCA header mode on all cpu ports */
-		if (dsa_is_cpu_port(ds, i)) {
-			ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(i),
-					  FIELD_PREP(QCA8K_PORT_HDR_CTRL_TX_MASK, QCA8K_PORT_HDR_CTRL_ALL) |
-					  FIELD_PREP(QCA8K_PORT_HDR_CTRL_RX_MASK, QCA8K_PORT_HDR_CTRL_ALL));
-			if (ret) {
-				dev_err(priv->dev, "failed enabling QCA header mode");
-				return ret;
-			}
+	/* Disable MAC by default on all user ports */
+	dsa_switch_for_each_user_port(dp, ds)
+		qca8k_port_set_status(priv, dp->index, 0);
+
+	/* Enable QCA header mode on all cpu ports */
+	dsa_switch_for_each_cpu_port(dp, ds) {
+		ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(dp->index),
+				  FIELD_PREP(QCA8K_PORT_HDR_CTRL_TX_MASK, QCA8K_PORT_HDR_CTRL_ALL) |
+				  FIELD_PREP(QCA8K_PORT_HDR_CTRL_RX_MASK, QCA8K_PORT_HDR_CTRL_ALL));
+		if (ret) {
+			dev_err(priv->dev, "failed enabling QCA header mode on port %d", dp->index);
+			return ret;
 		}
-
-		/* Disable MAC by default on all user ports */
-		if (dsa_is_user_port(ds, i))
-			qca8k_port_set_status(priv, i, 0);
 	}
 
 	/* Forward all unknown frames to CPU port for Linux processing
@@ -1897,48 +1898,48 @@ qca8k_setup(struct dsa_switch *ds)
 		return ret;
 
 	/* Setup connection between CPU port & user ports
-	 * Configure specific switch configuration for ports
+	 * Individual user ports get connected to CPU port only
 	 */
-	for (i = 0; i < QCA8K_NUM_PORTS; i++) {
-		/* Individual user ports get connected to CPU port only */
-		if (dsa_is_user_port(ds, i)) {
-			ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
-					QCA8K_PORT_LOOKUP_MEMBER,
-					BIT(cpu_port));
-			if (ret)
-				return ret;
-
-			ret = regmap_clear_bits(priv->regmap, QCA8K_PORT_LOOKUP_CTRL(i),
-						QCA8K_PORT_LOOKUP_LEARN);
-			if (ret)
-				return ret;
-
-			/* For port based vlans to work we need to set the
-			 * default egress vid
-			 */
-			ret = qca8k_rmw(priv, QCA8K_EGRESS_VLAN(i),
-					QCA8K_EGREES_VLAN_PORT_MASK(i),
-					QCA8K_EGREES_VLAN_PORT(i, QCA8K_PORT_VID_DEF));
-			if (ret)
-				return ret;
-
-			ret = qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(i),
-					  QCA8K_PORT_VLAN_CVID(QCA8K_PORT_VID_DEF) |
-					  QCA8K_PORT_VLAN_SVID(QCA8K_PORT_VID_DEF));
-			if (ret)
-				return ret;
-		}
+	dsa_switch_for_each_user_port(dp, ds) {
+		u8 port = dp->index;
+
+		ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port),
+				QCA8K_PORT_LOOKUP_MEMBER,
+				BIT(cpu_port));
+		if (ret)
+			return ret;
+
+		ret = regmap_clear_bits(priv->regmap, QCA8K_PORT_LOOKUP_CTRL(port),
+					QCA8K_PORT_LOOKUP_LEARN);
+		if (ret)
+			return ret;
 
-		/* The port 5 of the qca8337 have some problem in flood condition. The
-		 * original legacy driver had some specific buffer and priority settings
-		 * for the different port suggested by the QCA switch team. Add this
-		 * missing settings to improve switch stability under load condition.
-		 * This problem is limited to qca8337 and other qca8k switch are not affected.
+		/* For port based vlans to work we need to set the
+		 * default egress vid
 		 */
-		if (priv->switch_id == QCA8K_ID_QCA8337)
-			qca8k_setup_hol_fixup(priv, i);
+		ret = qca8k_rmw(priv, QCA8K_EGRESS_VLAN(port),
+				QCA8K_EGREES_VLAN_PORT_MASK(port),
+				QCA8K_EGREES_VLAN_PORT(port, QCA8K_PORT_VID_DEF));
+		if (ret)
+			return ret;
+
+		ret = qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(port),
+				  QCA8K_PORT_VLAN_CVID(QCA8K_PORT_VID_DEF) |
+				  QCA8K_PORT_VLAN_SVID(QCA8K_PORT_VID_DEF));
+		if (ret)
+			return ret;
 	}
 
+	/* The port 5 of the qca8337 have some problem in flood condition. The
+	 * original legacy driver had some specific buffer and priority settings
+	 * for the different port suggested by the QCA switch team. Add this
+	 * missing settings to improve switch stability under load condition.
+	 * This problem is limited to qca8337 and other qca8k switch are not affected.
+	 */
+	if (priv->switch_id == QCA8K_ID_QCA8337)
+		dsa_switch_for_each_available_port(dp, ds)
+			qca8k_setup_hol_fixup(priv, dp->index);
+
 	/* Special GLOBAL_FC_THRESH value are needed for ar8327 switch */
 	if (priv->switch_id == QCA8K_ID_QCA8327) {
 		mask = QCA8K_GLOBAL_FC_GOL_XON_THRES(288) |
-- 
2.40.1

Re: [net-next PATCH v3 4/5] net: dsa: qca8k: move qca8xxx hol fixup to separate function

[Florian Fainelli]

On 7/30/23 00:41, Christian Marangi wrote:
> Move qca8xxx hol fixup to separate function to tidy things up and to
> permit using a more efficent loop in future patch.
> 
> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
-- 
Florian

Re: [net-next PATCH v3 5/5] net: dsa: qca8k: use dsa_for_each macro instead of for loop

[Florian Fainelli]

On 7/30/23 00:41, Christian Marangi wrote:
> Convert for loop to dsa_for_each macro to save some redundant write on
> unconnected/unused port and tidy things up.
> 
> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>

Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
-- 
Florian

Re: [net-next PATCH v3 1/5] net: dsa: tag_qca: return early if dev is not found

[patchwork-bot+netdevbpf]

Hello:

This series was applied to netdev/net-next.git (main)
by Paolo Abeni <pabeni@redhat.com>:

On Sun, 30 Jul 2023 09:41:09 +0200 you wrote:
> Currently checksum is recalculated and dsa tag stripped even if we later
> don't find the dev.
> 
> To improve code, exit early if we don't find the dev and skip additional
> operation on the skb since it will be freed anyway.
> 
> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
> Reviewed-by: Simon Horman <simon.horman@corigine.com>
> Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
> 
> [...]

Here is the summary with links:
  - [net-next,v3,1/5] net: dsa: tag_qca: return early if dev is not found
    https://git.kernel.org/netdev/net-next/c/de9db136dcc3
  - [net-next,v3,2/5] net: dsa: qca8k: make learning configurable and keep off if standalone
    https://git.kernel.org/netdev/net-next/c/23cfc7172e52
  - [net-next,v3,3/5] net: dsa: qca8k: limit user ports access to the first CPU port on setup
    https://git.kernel.org/netdev/net-next/c/18e8feae4a80
  - [net-next,v3,4/5] net: dsa: qca8k: move qca8xxx hol fixup to separate function
    https://git.kernel.org/netdev/net-next/c/a9108b0712bf
  - [net-next,v3,5/5] net: dsa: qca8k: use dsa_for_each macro instead of for loop
    https://git.kernel.org/netdev/net-next/c/01e6f8ad8d26

You are awesome, thank you!
-- 
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html