Re: [PATCH] stmmac: pci: Add support for LS7A bridge chip

* Re: [PATCH] stmmac: pci: Add support for LS7A bridge chip
       [not found] <1606125828-15742-1-git-send-email-lizhi01@loongson.cn>
@ 2020-11-23 10:31 ` Jiaxun Yang
  2020-11-25  7:07   ` Zhi Li
  0 siblings, 1 reply; 6+ messages in thread
From: Jiaxun Yang @ 2020-11-23 10:31 UTC (permalink / raw)
  To: lizhi01, davem, kuba, mcoquelin.stm32
  Cc: lixuefeng, gaojuxin, linux-kernel, netdev

Hi Lizhi,

You didn't send the patch to any mail list, is this intentional?

在 2020/11/23 18:03, lizhi01 写道:
> Add gmac driver to support LS7A bridge chip.
>
> Signed-off-by: lizhi01 <lizhi01@loongson.cn>
> ---
>   arch/mips/configs/loongson3_defconfig              |   4 +-
>   drivers/net/ethernet/stmicro/stmmac/Kconfig        |   8 +
>   drivers/net/ethernet/stmicro/stmmac/Makefile       |   1 +
>   .../net/ethernet/stmicro/stmmac/dwmac-loongson.c   | 194 +++++++++++++++++++++
>   4 files changed, 206 insertions(+), 1 deletion(-)
>   create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
>
> diff --git a/arch/mips/configs/loongson3_defconfig b/arch/mips/configs/loongson3_defconfig
> index 38a817e..2e8d2be 100644
> --- a/arch/mips/configs/loongson3_defconfig
> +++ b/arch/mips/configs/loongson3_defconfig
> @@ -225,7 +225,9 @@ CONFIG_R8169=y
>   # CONFIG_NET_VENDOR_SILAN is not set
>   # CONFIG_NET_VENDOR_SIS is not set
>   # CONFIG_NET_VENDOR_SMSC is not set
> -# CONFIG_NET_VENDOR_STMICRO is not set
> +CONFIG_NET_VENDOR_STMICR=y
> +CONFIG_STMMAC_ETH=y
> +CONFIG_DWMAC_LOONGSON=y
>   # CONFIG_NET_VENDOR_SUN is not set
>   # CONFIG_NET_VENDOR_TEHUTI is not set
>   # CONFIG_NET_VENDOR_TI is not set
> diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> index 53f14c5..30117cb 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
> +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
> @@ -230,6 +230,14 @@ config DWMAC_INTEL
>   	  This selects the Intel platform specific bus support for the
>   	  stmmac driver. This driver is used for Intel Quark/EHL/TGL.
>   
> +config DWMAC_LOONGSON
> +	tristate "Intel GMAC support"
> +	depends on STMMAC_ETH && PCI
> +	depends on COMMON_CLK
> +	help
> +	  This selects the Intel platform specific bus support for the
> +	  stmmac driver.

Intel ???

> +
>   config STMMAC_PCI
>   	tristate "STMMAC PCI bus support"
>   	depends on STMMAC_ETH && PCI
> diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
> index 24e6145..11ea4569 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/Makefile
> +++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
> @@ -34,4 +34,5 @@ dwmac-altr-socfpga-objs := altr_tse_pcs.o dwmac-socfpga.o
>   
>   obj-$(CONFIG_STMMAC_PCI)	+= stmmac-pci.o
>   obj-$(CONFIG_DWMAC_INTEL)	+= dwmac-intel.o
> +obj-$(CONFIG_DWMAC_LOONGSON)	+= dwmac-loongson.o
>   stmmac-pci-objs:= stmmac_pci.o
> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
> new file mode 100644
> index 0000000..765412e
> --- /dev/null
> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-loongson.c
> @@ -0,0 +1,194 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/* Copyright (c) 2020, Loongson Corporation
> + */
> +
> +#include <linux/clk-provider.h>
> +#include <linux/pci.h>
> +#include <linux/dmi.h>
> +#include <linux/device.h>
> +#include <linux/of_irq.h>
> +#include "stmmac.h"
> +
> +struct stmmac_pci_info {
> +	int (*setup)(struct pci_dev *pdev, struct plat_stmmacenet_data *plat);
> +};
> +
> +static void common_default_data(struct plat_stmmacenet_data *plat)
> +{
> +	plat->clk_csr = 2;
> +	plat->has_gmac = 1;
> +	plat->force_sf_dma_mode = 1;
> +	
> +	plat->mdio_bus_data->needs_reset = true;
> +
> +	plat->multicast_filter_bins = HASH_TABLE_SIZE;
> +
> +	plat->unicast_filter_entries = 1;
> +
> +	plat->maxmtu = JUMBO_LEN;
> +
> +	plat->tx_queues_to_use = 1;
> +	plat->rx_queues_to_use = 1;
> +
> +	plat->tx_queues_cfg[0].use_prio = false;
> +	plat->rx_queues_cfg[0].use_prio = false;
> +
> +	plat->rx_queues_cfg[0].pkt_route = 0x0;
> +}
> +
> +static int loongson_default_data(struct pci_dev *pdev, struct plat_stmmacenet_data *plat)
> +{
> +	common_default_data(plat);
> +	
> +	plat->bus_id = pci_dev_id(pdev);
> +	plat->phy_addr = -1;
> +	plat->interface = PHY_INTERFACE_MODE_GMII;
> +
> +	plat->dma_cfg->pbl = 32;
> +	plat->dma_cfg->pblx8 = true;
> +
> +	plat->multicast_filter_bins = 256;
> +
> +	return 0;	
> +}

You can merge common and Loongson config as the driver is solely used by 
Loongson.

The callback is not necessary as well...

> +
> +static const struct stmmac_pci_info loongson_pci_info = {
> +	.setup = loongson_default_data,
> +};
> +
> +static int loongson_gmac_probe(struct pci_dev *pdev, const struct pci_device_id *id)
> +{
> +	struct stmmac_pci_info *info = (struct stmmac_pci_info *)id->driver_data;
> +	struct plat_stmmacenet_data *plat;
> +	struct stmmac_resources res;
> +	int ret, i, lpi_irq;
> +	struct device_node *np;	
> +	
> +	plat = devm_kzalloc(&pdev->dev, sizeof(struct plat_stmmacenet_data), GFP_KERNEL);
> +	if (!plat)
> +		return -ENOMEM;
> +
> +	plat->mdio_bus_data = devm_kzalloc(&pdev->dev, sizeof(struct stmmac_mdio_bus_data), GFP_KERNEL);
> +	if (!plat->mdio_bus_data) {
> +		kfree(plat);
> +		return -ENOMEM;
> +	}
> +
> +	plat->dma_cfg = devm_kzalloc(&pdev->dev, sizeof(struct stmmac_dma_cfg), GFP_KERNEL);
> +	if (!plat->dma_cfg)	{
> +		kfree(plat);
> +		return -ENOMEM;
> +	}
> +
> +	ret = pci_enable_device(pdev);
> +	if (ret) {
> +		dev_err(&pdev->dev, "%s: ERROR: failed to enable device\n", __func__);
> +		kfree(plat);
> +		return ret;
> +	}
> +
> +	for (i = 0; i < PCI_STD_NUM_BARS; i++) {
> +		if (pci_resource_len(pdev, i) == 0)
> +			continue;
> +		ret = pcim_iomap_regions(pdev, BIT(0), pci_name(pdev));
> +		if (ret)
> +			return ret;
> +		break;
> +	}

The BAR order is fixed on Loongson so there is no need to check it one 
by one.

Simply use BAR0 instead.

> +
> +	pci_set_master(pdev);
> +
> +	ret = info->setup(pdev, plat);
> +	if (ret)
> +		return ret;
> +
> +	pci_enable_msi(pdev);
> +
> +	memset(&res, 0, sizeof(res));
> +	res.addr = pcim_iomap_table(pdev)[i];
> +	res.irq = pdev->irq;
> +	res.wol_irq = pdev->irq;	
> +
> +	np = dev_of_node(&pdev->dev);

Please check the node earlier and bailing out in case if there is no node.

Also you should get both IRQs via DT to avoid misordering.

> +	lpi_irq = of_irq_get_byname(np, "eth_lpi");
> +	res.lpi_irq = lpi_irq;
> +	
> +	return stmmac_dvr_probe(&pdev->dev, plat, &res);
> +}
> +
> +static void loongson_gmac_remove(struct pci_dev *pdev)
> +{
> +	int i;
> +	
> +	stmmac_dvr_remove(&pdev->dev);
> +	
> +	for (i = 0; i < PCI_STD_NUM_BARS; i++) {
> +		if (pci_resource_len(pdev, i) == 0)
> +			continue;
> +		pcim_iounmap_regions(pdev, BIT(i));
> +		break;
> +	}
> +
> +	pci_disable_device(pdev);
> +}
> +
> +static int __maybe_unused loongson_eth_pci_suspend(struct device *dev)
> +{
> +	struct pci_dev *pdev = to_pci_dev(dev);
> +	int ret;
> +
> +	ret = stmmac_suspend(dev);
> +	if (ret)
> +		return ret;
> +	
> +	ret = pci_save_state(pdev);
> +	if (ret)
> +		return ret;
> +
> +	pci_disable_device(pdev);
> +	pci_wake_from_d3(pdev, true);
> +	return 0;
> +}
> +
> +static int __maybe_unused loongson_eth_pci_resume(struct device *dev)
> +{
> +	struct pci_dev *pdev = to_pci_dev(dev);
> +	int ret;
> +
> +	pci_restore_state(pdev);
> +	pci_set_power_state(pdev, PCI_D0);
> +
> +	ret = pci_enable_device(pdev);
> +	if (ret)
> +		return ret;
> +	
> +	pci_set_master(pdev);
> +	
> +	return stmmac_resume(dev);
> +}	
> +
> +static SIMPLE_DEV_PM_OPS(loongson_eth_pm_ops, loongson_eth_pci_suspend, loongson_eth_pci_resume);
> +
> +#define PCI_DEVICE_ID_LOONGSON_GMAC 0x7a03
> +
> +static const struct pci_device_id loongson_gmac_table[] = {
> +	{ PCI_DEVICE_DATA(LOONGSON, GMAC, &loongson_pci_info) },
> +	{}
> +};
> +MODULE_DEVICE_TABLE(pci, loongson_gmac_table);
> +
> +struct pci_driver loongson_gmac_driver = {
> +	.name = "loongson gmac",
> +	.id_table = loongson_gmac_table,
> +	.probe = loongson_gmac_probe,
> +	.remove = loongson_gmac_remove,
> +	.driver = {
> +		.pm = &loongson_eth_pm_ops,
> +	},
> +};
> +
> +module_pci_driver(loongson_gmac_driver);
> +
> +MODULE_DESCRIPTION("Loongson DWMAC PCI driver");
> +MODULE_AUTHOR("Zhi Li <lizhi01@loongson.com>");
> +MODULE_LICENSE("GPL v2");

Thanks

- Jiaxun

^ permalink raw reply	[flat|nested] 6+ messages in thread