Re: [PATCH net-next v2 2/4] can: cc770: add legacy ISA bus driver for the CC770 and AN82527

[Wolfgang Zarre <info@essax.com>]

Hello Oliver,

> Hello Wolfgang,
>
> many thanks for posting this driver. Indeed this is the last from the missing
> drivers in the SVN ...

@Wolfgang

The same her, thanks a lot.

>
> I added Wolfgang Zarre to the list of recipients who tested your CC770 driver
> recently:
>
> http://old.nabble.com/Compile-Fails-On-2.6.39-2-td32259346.html
>
> Maybe he can check this latest version and can send a "Tested-by:"
>
> @Wolfgang Zarre: The entire patch set from Wolfgang Grandegger is here:
>
> http://patchwork.ozlabs.org/patch/127653/
> http://patchwork.ozlabs.org/patch/127651/
> http://patchwork.ozlabs.org/patch/127654/
> http://patchwork.ozlabs.org/patch/127652/

In fact a month ago we discovered a problem with the previous isa driver but were not
able to reproduce it.

Last Friday during a test run we got the same problem and with some further tests I
was able to reproduce and started with some investigation.

So the patches came in quite handy and even not to waste time I was applying the
patches to an updated svn tree but had to do some manual corrections to get it
compiled.

So far the driver is functioning quite good and I was hoping that our problem would
be solved as well.

But unfortunately that is not the case and it would be great if somebody would have
an idea or similar experience and maybe a solution.

In use:
ISA card: B&R with CC770 (40007) Series Bosch CAN Controller - LQFP-44
Kernel: 2.6.39.4
Module: modprobe cc770_isa irq=0xa port=0x384 indirect=1
Commands: ip link set can0 up type can bitrate 500000;ip link set can0 txqueuelen 2000

dmesg:
[190911.144337] CAN device driver interface
[190911.153316] cc770 CAN netdevice driver
[190911.159708] cc770_isa: platform device 0: port=0x384, mem=0x0, irq=10
[190911.159740] cc770_isa cc770_isa.0: probing idx=0: port=0x384, mem=0x0, irq=10
[190911.159799] cc770_isa cc770_isa.0: (unregistered net_device): i82527 mode with additional functions
[190911.161338] cc770_isa cc770_isa.0: cc770_isa device registered (reg_base=0x00000384, irq=10)
[190911.161384] Legacy cc770_isa driver for max. 8 devices registered
[190912.173762] cc770_isa cc770_isa.0: can0: setting BTR0=0x00 BTR1=0x1c
[190912.173835] cc770_isa cc770_isa.0: can0: Message object 15 for RX data, RTR, SFF and EFF
[190912.173852] cc770_isa cc770_isa.0: can0: Message object 11 for TX data, RTR, SFF and EFF


Description of problem:
After a while sending quite some telegrams the driver of a sudden stops transmitting
and the queue is running full but still capable to receive telegrams.
This issue is not depending on the amount of transmitted telegrams and also no logfile
entries.

Further it is possible to recover with ip link set down and up again.


>
> Just a nitpick in the description:
>
>> Furthermore, the following mode parameter can be defined:
>
>>
>>    clk: External oscillator clock frequency (default=16000000 [16 MHz])
>>    cir: CPU interface register (default=0x40 [DSC])
>>    ocr, Bus configuration register (default=0x40 [CBY])
>
>
> ->  bcr: CPU ...
>
>>    cor, Clockout register (default=0x00)
>
>
> ->  cor: Clockout ...
>
> Regards,
> Oliver

Thanks in advance.

Regards
Wolfgang