Re: [RFC PATCH v4 0/4] Create common DPLL/clock configuration API

[Jiri Pirko <jiri@resnulli.us>]

Wed, Jan 11, 2023 at 04:30:44PM CET, arkadiusz.kubalewski@intel.com wrote:
>>From: Jiri Pirko <jiri@resnulli.us>
>>Sent: Wednesday, January 11, 2023 4:05 PM
>>To: Kubalewski, Arkadiusz <arkadiusz.kubalewski@intel.com>
>>
>>Wed, Jan 11, 2023 at 03:16:59PM CET, arkadiusz.kubalewski@intel.com wrote:
>>>>From: Jiri Pirko <jiri@resnulli.us>
>>>>Sent: Wednesday, January 11, 2023 9:20 AM
>>>>
>>>>Tue, Jan 10, 2023 at 09:05:49PM CET, kuba@kernel.org wrote:
>>>>>On Mon, 9 Jan 2023 14:43:01 +0000 Kubalewski, Arkadiusz wrote:
>>>>>> This is a simplified network switch board example.
>>>>>> It has 2 synchronization channels, where each channel:
>>>>>> - provides clk to 8 PHYs driven by separated MAC chips,
>>>>>> - controls 2 DPLLs.
>>>>>>
>>>>>> Basically only given FW has control over its PHYs, so also a control
>>>>over it's
>>>>>> MUX inputs.
>>>>>> All external sources are shared between the channels.
>>>>>>
>>>>>> This is why we believe it is not best idea to enclose multiple DPLLs
>>>>with one
>>>>>> object:
>>>>>> - sources are shared even if DPLLs are not a single synchronizer chip,
>>>>>> - control over specific MUX type input shall be controllable from
>>>>different
>>>>>> driver/firmware instances.
>>>>>>
>>>>>> As we know the proposal of having multiple DPLLs in one object was a
>>try
>>>>to
>>>>>> simplify currently implemented shared pins. We fully support idea of
>>>>having
>>>>>> interfaces as simple as possible, but at the same time they shall be
>>>>flexible
>>>>>> enough to serve many use cases.
>>>>>
>>>>>I must be missing context from other discussions but what is this
>>>>>proposal trying to solve? Well implemented shared pins is all we need.
>>>>
>>>>There is an entity containing the pins. The synchronizer chip. One
>>>>synchronizer chip contains 1-n DPLLs. The source pins are connected
>>>>to each DPLL (usually). What we missed in the original model was the
>>>>synchronizer entity. If we have it, we don't need any notion of somehow
>>>>floating pins as independent entities being attached to one or many
>>>>DPLL refcounted, etc. The synchronizer device holds them in
>>>>straightforward way.
>>>>
>>>>Example of a synchronizer chip:
>>>>https://www.renesas.com/us/en/products/clocks-timing/jitter-attenuators-
>>>>frequency-translation/8a34044-multichannel-dpll-dco-four-eight-
>>>>channels#overview
>>>
>>>Not really, as explained above, multiple separated synchronizer chips can
>>be
>>>connected to the same external sources.
>>>This is why I wrote this email, to better explain need for references
>>between
>>>DPLLs and shared pins.
>>>Synchronizer chip object with multiple DPLLs would have sense if the pins
>>would
>>>only belong to that single chip, but this is not true.
>>
>>I don't understand how it is physically possible that 2 pins belong to 2
>>chips. Could you draw this to me?
>>
>
>Well, sure, I was hoping this is clear, without extra connections on the draw:

Okay, now I understand. It is not a shared pin but shared source for 2
pins.


>+----------+                 
>|i0 - GPS  |--------------\
>+----------+              |
>+----------+              |
>|i1 - SMA1 |------------\ |
>+----------+            | |
>+----------+            | |
>|i2 - SMA2 |----------\ | |
>+----------+          | | |
>                      | | |
>+---------------------|-|-|-------------------------------------------+
>| Channel A / FW0     | | |     +-------------+   +---+   +--------+  |
>|                     | | |-i0--|Synchronizer0|---|   |---| PHY0.0 |--|

One pin here               ^^^

>|         +---+       | | |     |             |   |   |   +--------+  |
>| PHY0.0--|   |       | |---i1--|             |---| M |---| PHY0.1 |--|
>|         |   |       | | |     | +-----+     |   | A |   +--------+  |
>| PHY0.1--| M |       |-----i2--| |DPLL0|     |   | C |---| PHY0.2 |--|
>|         | U |       | | |     | +-----+     |   | 0 |   +--------+  |
>| PHY0.2--| X |--+----------i3--| +-----+     |---|   |---| ...    |--|
>|         | 0 |  |    | | |     | |DPLL1|     |   |   |   +--------+  |
>| ...   --|   |  | /--------i4--| +-----+     |---|   |---| PHY0.7 |--|
>|         |   |  | |  | | |     +-------------+   +---+   +--------+  |
>| PHY0.7--|   |  | |  | | |                                           |
>|         +---+  | |  | | |                                           |
>+----------------|-|--|-|-|-------------------------------------------+
>| Channel B / FW1| |  | | |     +-------------+   +---+   +--------+  |
>|                | |  | | \-i0--|Synchronizer1|---|   |---| PHY1.0 |--|

And second pin here        ^^^

There are 2 separate pins. Sure, they need to have the same config as
they are connected to the same external entity (GPS, SMA1, SMA2).

Perhaps we need to have a board description using dts to draw this
picture so the drivers can use this schema in order to properly
configure this?

My point is, you are trying to hardcode the board geometry in the
driver. Is that correct?


>|         +---+  | |  | |       |             |   |   |   +--------+  |
>| PHY1.0--|   |  | |  | \---i1--|             |---| M |---| PHY1.1 |--|
>|         |   |  | |  |         | +-----+     |   | A |   +--------+  |
>| PHY1.1--| M |  | |  \-----i2--| |DPLL0|     |   | C |---| PHY1.2 |--|
>|         | U |  | |            | +-----+     |   | 1 |   +--------+  |
>| PHY1.2--| X |  \-|--------i3--| +-----+     |---|   |---| ...    |--|
>|         | 1 |    |            | |DPLL1|     |   |   |   +--------+  |
>| ...   --|   |----+--------i4--| +-----+     |---|   |---| PHY1.7 |--|
>|         |   |                 +-------------+   +---+   +--------+  |
>| PHY1.7--|   |                                                       |
>|         +---+                                                       |
>+---------------------------------------------------------------------+
>
>>
>>>As the pins are shared between multiple DPLLs (both inside 1 integrated
>>circuit
>>>and between multiple integrated circuits), all of them shall have current
>>state
>>>of the source or output.
>>>Pins still need to be shared same as they would be inside of one
>>synchronizer
>>>chip.
>>
>>Do I understand correctly that you connect one synchronizer output to
>>the input of the second synchronizer chip?
>
>No, I don't recall such use case. At least nothing that needs to exposed
>in the DPLL subsystem itself.
>
>BR,
>Arkadiusz
>
>>
>>>
>>>BR,
>>>Arkadiusz