From: 吳秉昌 <wh800805@gmail.com>
To: Andrei Kartashev <a.kartashev@yadro.com>
Cc: openbmc@lists.ozlabs.org
Subject: Re: Ipmitool command & entity-manager question
Date: Thu, 30 Sep 2021 18:13:07 +0800 [thread overview]
Message-ID: <2BD99E33-F582-46C5-855F-942532F79FCC@gmail.com> (raw)
In-Reply-To: <27ffb02323b8be39e1e92b37fc3cdc35857312b8.camel@yadro.com>
Hi Andrei
My question is that I set MB_P12V "upper critical" is 13.23, "upper non critical" is 12.6, etc .
When I login web page, I can see the setting what I want.
But when I use “Ipmitool sensor” command, the response is wrong. Like below
MB P12V | 7.215 | Volts | ok | na |6.386 | 6.723 | 7.429 | 7.829 | na
I am not sure am I miss something.
Thanks
Paul
> Andrei Kartashev <a.kartashev@yadro.com> 於 2021年9月30日 下午6:03 寫道：
>
> Hello,
>
> What is your question exactly?
> If it is about precision, then you should take in account that IPMI use
> 8-bit variables to represent values and some coefficients which
> calculated based on MinValue/MaxValue parameters of corresponding
> Sensor interface.
> You will never get exact values in IPMI, unless you values can fit to
> 8-bit integer.
>
> On Thu, 2021-09-30 at 17:07 +0800, 吳秉昌 wrote:
>> Hi all
>>
>> I add the sensor in entity-manager config like below
>> {
>> "Index": 2,
>> "Name": "MB_VMEM",
>> "PowerState": "On",
>> "ScaleFactor": 1,
>> "Thresholds": [
>> {
>> "Direction": "greater than",
>> "Name": "upper critical",
>> "Severity": 1,
>> "Value": 1.32
>> },
>> {
>> "Direction": "greater than",
>> "Name": "upper non critical",
>> "Severity": 0,
>> "Value": 1.26
>> },
>> {
>> "Direction": "less than",
>> "Name": "lower non critical",
>> "Severity": 0,
>> "Value": 1.14
>> },
>> {
>> "Direction": "less than",
>> "Name": "lower critical",
>> "Severity": 1,
>> "Value": 1.08
>> }
>> ],
>> "Type": "ADC"
>> },
>> {
>> "Index": 3,
>> "Name": "MB_P12V",
>> "PowerState": "On",
>> "ScaleFactor": 0.23,
>> "Thresholds": [
>> {
>> "Direction": "greater than",
>> "Name": "upper critical",
>> "Severity": 1,
>> "Value": 13.23
>> },
>> {
>> "Direction": "greater than",
>> "Name": "upper non critical",
>> "Severity": 0,
>> "Value": 12.6
>> },
>> {
>> "Direction": "less than",
>> "Name": "lower non critical",
>> "Severity": 0,
>> "Value": 11.4
>> },
>> {
>> "Direction": "less than",
>> "Name": "lower critical",
>> "Severity": 1,
>> "Value": 10.77
>> }
>> ],
>> "Type": "ADC"
>> },
>> {
>> "Index": 4,
>> "Name": "MB_P5V",
>> "PowerState": "On",
>> "ScaleFactor": 0.55,
>> "Thresholds": [
>> {
>> "Direction": "greater than",
>> "Name": "upper critical",
>> "Severity": 1,
>> "Value": 5.48
>> },
>> {
>> "Direction": "greater than",
>> "Name": "upper non critical",
>> "Severity": 0,
>> "Value": 5.24
>> },
>> {
>> "Direction": "less than",
>> "Name": "lower non critical",
>> "Severity": 0,
>> "Value": 4.76
>> },
>> {
>> "Direction": "less than",
>> "Name": "lower critical",
>> "Severity": 1,
>> "Value": 4.48
>> }
>> ],
>> "Type": "ADC"
>> },
>> {
>> "Index": 5,
>> "Name": "MB_P5V_SB",
>> "PowerState": "On",
>> "ScaleFactor": 0.25,
>> "Thresholds": [
>> {
>> "Direction": "greater than",
>> "Name": "upper critical",
>> "Severity": 1,
>> "Value": 5.48
>> },
>> {
>> "Direction": "greater than",
>> "Name": "upper non critical",
>> "Severity": 0,
>> "Value": 5.24
>> },
>> {
>> "Direction": "less than",
>> "Name": "lower non critical",
>> "Severity": 0,
>> "Value": 4.76
>> },
>> {
>> "Direction": "less than",
>> "Name": "lower critical",
>> "Severity": 1,
>> "Value": 4.48
>> }
>> ],
>> "Type": "ADC"
>> },
>>
>>
>> I use the busctrl command to see MB_P5V_SB information, it is normal.
>> root@fws7830bmc:~# busctl introspect --no-pager
>> xyz.openbmc_project.EntityManager
>> /xyz/openbmc_project/inventory/system/board/FWS7830_
>> Baseboard/MB_P5V
>> NAME TYPE SIGNATURE
>> RESULT/VALUE FLAGS
>> org.freedesktop.DBus.Introspectable interface -
>> - -
>> .Introspect method -
>> s -
>> org.freedesktop.DBus.Peer interface -
>> - -
>> .GetMachineId method -
>> s -
>> .Ping method -
>> - -
>> org.freedesktop.DBus.Properties interface -
>> - -
>> .Get method ss
>> v -
>> .GetAll method s
>> a{sv} -
>> .Set method ssv
>> - -
>> .PropertiesChanged signal
>> sa{sv}as - -
>> xyz.openbmc_project.Configuration.ADC interface -
>> - -
>> .Index property t
>> 4 emits-change
>> .Name property s
>> "MB_P5V" emits-change
>> .PowerState property s
>> "On" emits-change
>> .ScaleFactor property d
>> 0.55 emits-change
>> .Type property s
>> "ADC" emits-change
>> xyz.openbmc_project.Configuration.ADC.Thresholds0 interface -
>> - -
>> .Delete method -
>> - -
>> .Direction property s
>> "greater than" emits-change writable
>> .Name property s
>> "upper critical" emits-change writable
>> .Severity property d
>> 1 emits-change writable
>> .Value property d
>> 5.48 emits-change writable
>> xyz.openbmc_project.Configuration.ADC.Thresholds1 interface -
>> - -
>> .Delete method -
>> - -
>> .Direction property s
>> "greater than" emits-change writable
>> .Name property s
>> "upper non critical" emits-change writable
>> .Severity property d
>> 0 emits-change writable
>> .Value property d
>> 5.24 emits-change writable
>> xyz.openbmc_project.Configuration.ADC.Thresholds2 interface -
>> - -
>> .Delete method -
>> - -
>> .Direction property s
>> "less than" emits-change writable
>> .Name property s
>> "lower non critical" emits-change writable
>> .Severity property d
>> 0 emits-change writable
>> .Value property d
>> 4.76 emits-change writable
>> xyz.openbmc_project.Configuration.ADC.Thresholds3 interface -
>> - -
>> .Delete method -
>> - -
>> .Direction property s
>> "less than" emits-change writable
>> .Name property s
>> "lower critical" emits-change writable
>> .Severity property d
>> 1 emits-change writable
>> .Value property d
>> 4.48 emits-change writable
>>
>> But I use "ipmitoo sensor” command, it return the error information
>> below as
>> MB P3V3 | 3.271 | Volts | ok | na |
>> 2.947 | 3.046 | 3.511 | 3.596 | na
>> MB P5V | 2.982 | Volts | ok | na |
>> 2.662 | 2.829 | 3.123 | 3.264 | na
>> MB P5V SB | 5.048 | Volts | ok | na |
>> 4.484 | 4.766 | 5.245 | 5.471 | na
>> MB P12V | 7.215 | Volts | ok | na |
>> 6.386 | 6.723 | 7.429 | 7.829 | na
>>
>> Please give me some advise.
>>
>> Many thanks
>> Paul
>>
>
> --
> Best regards,
> Andrei Kartashev
>
>
next prev parent reply other threads:[~2021-09-30 10:13 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-09-30 9:07 Ipmitool command & entity-manager question 吳秉昌
2021-09-30 10:03 ` Andrei Kartashev
2021-09-30 10:13 ` 吳秉昌 [this message]
2021-09-30 15:00 ` Johnathan Mantey
2021-10-01 7:52 ` 吳秉昌
[not found] ` <99511633084704@mail.yandex-team.ru>
2021-10-13 9:05 ` 吳秉昌
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=2BD99E33-F582-46C5-855F-942532F79FCC@gmail.com \
--to=wh800805@gmail.com \
--cc=a.kartashev@yadro.com \
--cc=openbmc@lists.ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).