From: Joel Stanley <joel@jms.id.au>
To: "Lin.TommySC 林世欽 TAO" <Lin.TommySC@inventec.com>
Cc: "Ye.Vic 葉宇清 TAO" <ye.vic@inventec.com>,
"openbmc@lists.ozlabs.org" <openbmc@lists.ozlabs.org>,
"Mohammed.Habeeb ISV" <mohammed.habeeb@inventec.com>
Subject: Re: [PATCH v2] ARM: dts: aspeed: Adding Inventec Transformers BMC
Date: Mon, 18 Oct 2021 23:43:17 +0000 [thread overview]
Message-ID: <CACPK8XeZ9esWimkv+RbeP3xyohzcPiUkXFhDWqB6ANjJ0aBvHw@mail.gmail.com> (raw)
In-Reply-To: <e57d58c0b44b4a289c580e188f7d5580@inventec.com>
On Mon, 18 Oct 2021 at 22:51, Lin.TommySC 林世欽 TAO
<Lin.TommySC@inventec.com> wrote:
>
> Initial introduction of Inventec Transformers x86 family equipped with AST2600 BMC SoC.
>
> Signed-off-by: Tommy Lin <Lin.TommySC@inventec.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Thanks! I've applied this to the aspeed tree (but I've already sent my
pull request for v5.16) and to the openbmc tree.
Cheers,
Joel
> ---
> arch/arm/boot/dts/Makefile | 1 +
> .../dts/aspeed-bmc-inventec-transformers.dts | 457 ++++++++++++++++++
> 2 files changed, 458 insertions(+)
> create mode 100644 arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 48d48c85de9e..930b8ba6c3c5 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1407,6 +1407,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
> aspeed-bmc-intel-s2600wf.dtb \
> aspeed-bmc-inspur-fp5280g2.dtb \
> aspeed-bmc-inspur-nf5280m6.dtb \
> + aspeed-bmc-inventec-transformers.dtb \
> aspeed-bmc-lenovo-hr630.dtb \
> aspeed-bmc-lenovo-hr855xg2.dtb \
> aspeed-bmc-microsoft-olympus.dtb \
> diff --git a/arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts b/arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts
> new file mode 100644
> index 000000000000..71e85694c3c7
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed-bmc-inventec-transformers.dts
> @@ -0,0 +1,457 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +// Copyright 2021 Inventec Corp.
> +
> +/dts-v1/;
> +
> +#include "aspeed-g6.dtsi"
> +#include "aspeed-g6-pinctrl.dtsi"
> +#include <dt-bindings/i2c/i2c.h>
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +
> +/ {
> + model = "TRANSFORMERS BMC";
> + compatible = "inventec,transformer-bmc", "aspeed,ast2600";
> +
> + aliases {
> + serial4 = &uart5;
> + };
> +
> + chosen {
> + stdout-path = &uart5;
> + bootargs = "console=ttyS4,115200n8";
> + };
> +
> + memory@80000000 {
> + device_type = "memory";
> + reg = <0x80000000 0x80000000>;
> + };
> +
> + iio-hwmon {
> + compatible = "iio-hwmon";
> + io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>, <&adc0 4>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + // UID led
> + uid {
> + label = "UID_LED";
> + gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>;
> + };
> +
> + // Heart beat led
> + heartbeat {
> + label = "HB_LED";
> + gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + pwm_tacho {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_tach0_default
> + &pinctrl_pwm1_default &pinctrl_tach1_default
> + &pinctrl_pwm2_default &pinctrl_tach2_default
> + &pinctrl_pwm3_default &pinctrl_tach3_default
> + &pinctrl_pwm4_default &pinctrl_tach4_default
> + &pinctrl_pwm5_default &pinctrl_tach5_default
> + &pinctrl_pwm6_default &pinctrl_tach6_default
> + &pinctrl_pwm7_default &pinctrl_tach7_default
> + &pinctrl_tach8_default
> + &pinctrl_tach9_default
> + &pinctrl_tach10_default
> + &pinctrl_tach11_default
> + &pinctrl_tach12_default
> + &pinctrl_tach13_default
> + &pinctrl_tach14_default
> + &pinctrl_tach15_default>;
> + fan@0 {
> + reg = <0x00>;
> + aspeed,target_pwm = <25000>;
> + cooling-levels = <125 151 177 203 229 255>;
> + aspeed,fan-tach-ch = <0x00>;
> + aspeed,min_rpm = <750000>;
> + };
> +
> + fan@1 {
> + reg = <0x01>;
> + aspeed,target_pwm = <25000>;
> + cooling-levels = <125 151 177 203 229 255>;
> + aspeed,fan-tach-ch = <0x01>;
> + aspeed,min_rpm = <750000>;
> + };
> +
> + fan@2 {
> + reg = <0x02>;
> + aspeed,target_pwm = <25000>;
> + cooling-levels = <125 151 177 203 229 255>;
> + aspeed,fan-tach-ch = <0x02>;
> + aspeed,min_rpm = <750000>;
> + };
> +
> + fan@3 {
> + reg = <0x03>;
> + aspeed,target_pwm = <25000>;
> + cooling-levels = <125 151 177 203 229 255>;
> + aspeed,fan-tach-ch = <0x03>;
> + aspeed,min_rpm = <750000>;
> + };
> +
> + fan@4 {
> + reg = <0x04>;
> + aspeed,target_pwm = <25000>;
> + cooling-levels = <125 151 177 203 229 255>;
> + aspeed,fan-tach-ch = <0x04>;
> + aspeed,min_rpm = <750000>;
> + };
> +
> + fan@5 {
> + reg = <0x05>;
> + aspeed,target_pwm = <25000>;
> + cooling-levels = <125 151 177 203 229 255>;
> + aspeed,fan-tach-ch = <0x05>;
> + aspeed,min_rpm = <750000>;
> + };
> +
> + fan@6 {
> + reg = <0x06>;
> + aspeed,target_pwm = <25000>;
> + cooling-levels = <125 151 177 203 229 255>;
> + aspeed,fan-tach-ch = <0x06>;
> + aspeed,min_rpm = <750000>;
> + };
> +
> + fan@7 {
> + reg = <0x07>;
> + aspeed,target_pwm = <25000>;
> + cooling-levels = <125 151 177 203 229 255>;
> + aspeed,fan-tach-ch = <0x07>;
> + aspeed,min_rpm = <750000>;
> + };
> +
> + fan@8 {
> + reg = <0x08>;
> + aspeed,fan-tach-ch = <0x08>;
> + };
> +
> + fan@9 {
> + reg = <0x09>;
> + aspeed,fan-tach-ch = <0x09>;
> + };
> +
> + fan@10 {
> + reg = <0x0a>;
> + aspeed,fan-tach-ch = <0x0a>;
> + };
> +
> + fan@11 {
> + reg = <0x0b>;
> + aspeed,fan-tach-ch = <0x0b>;
> + };
> +
> + fan@12 {
> + reg = <0x0c>;
> + aspeed,fan-tach-ch = <0x0c>;
> + };
> +
> + fan@13 {
> + reg = <0x0d>;
> + aspeed,fan-tach-ch = <0x0d>;
> + };
> +
> + fan@14 {
> + reg = <0x0e>;
> + aspeed,fan-tach-ch = <0x0e>;
> + };
> +
> + fan@15 {
> + reg = <0x0f>;
> + aspeed,fan-tach-ch = <0x0f>;
> + };
> + };
> +};
> +
> +&mdio0 {
> + status = "okay";
> +
> + ethphy0: ethernet-phy@0 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + };
> +};
> +
> +&mac3 {
> + status = "okay";
> + phy-mode = "rgmii";
> + phy-handle = <ðphy0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_rgmii4_default>;
> +};
> +
> +&fmc {
> + status = "okay";
> +
> + flash@0 {
> + status = "okay";
> + m25p,fast-read;
> + label = "bmc";
> + spi-max-frequency = <33000000>;
> + spi-tx-bus-width = <2>;
> + spi-rx-bus-width = <2>;
> +#include "openbmc-flash-layout.dtsi"
> + };
> +
> + flash@1 {
> + status = "okay";
> + m25p,fast-read;
> + label = "bmc2";
> + spi-max-frequency = <33000000>;
> + spi-tx-bus-width = <2>;
> + spi-rx-bus-width = <2>;
> + };
> +};
> +
> +&spi1 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_spi1_default>;
> +
> + flash@0 {
> + status = "okay";
> + m25p,fast-read;
> + label = "bios";
> + spi-max-frequency = <33000000>;
> + spi-tx-bus-width = <1>;
> + spi-rx-bus-width = <1>;
> + };
> +};
> +
> +&wdt1 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + status = "okay";
> +};
> +
> +&uart5 {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + //Set bmc' slave address;
> + bmc_slave@10 {
> + compatible = "ipmb-dev";
> + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
> + i2c-protocol;
> + };
> +};
> +
> +&i2c2 {
> + status = "okay";
> +};
> +
> +&i2c3 {
> + // FRU AT24C512C-SSHM-T
> + status = "okay";
> + eeprom@50 {
> + compatible = "atmel,24c512";
> + reg = <0x50>;
> + pagesize = <128>;
> + };
> +};
> +
> +&i2c5 {
> + status = "okay";
> +};
> +
> +&i2c6 {
> + status = "okay";
> +
> + tmp75@49 {
> + compatible = "ti,tmp75";
> + reg = <0x49>;
> + };
> +
> + tmp75@4f {
> + compatible = "ti,tmp75";
> + reg = <0x4f>;
> + };
> +
> + tmp468@48 {
> + compatible = "ti,tmp468";
> + reg = <0x48>;
> + };
> +};
> +
> +&i2c7 {
> + status = "okay";
> + adm1278@40 {
> + compatible = "adi,adm1278";
> + reg = <0x40>;
> + };
> +};
> +
> +
> +&i2c8 {
> + // FRU AT24C512C-SSHM-T
> + status = "okay";
> +
> + eeprom@51 {
> + compatible = "atmel,24c512";
> + reg = <0x51>;
> + pagesize = <128>;
> + };
> +
> + eeprom@53 {
> + compatible = "atmel,24c512";
> + reg = <0x53>;
> + pagesize = <128>;
> + };
> +};
> +
> +&i2c9 {
> + // M.2
> + status = "okay";
> +};
> +
> +&i2c10 {
> + // I2C EXPANDER
> + status = "okay";
> +
> + i2c-switch@71 {
> + compatible = "nxp,pca9544";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x71>;
> + };
> +
> + i2c-switch@73 {
> + compatible = "nxp,pca9544";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x73>;
> + };
> +};
> +
> +&i2c11 {
> + // I2C EXPANDER
> + status = "okay";
> +
> + i2c-switch@70 {
> + compatible = "nxp,pca9544";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x70>;
> +
> + pcie_eeprom_riser1: i2c@0 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0>;
> +
> + eeprom@55 {
> + compatible = "atmel,24c512";
> + reg = <0x55>;
> + pagesize = <128>;
> + };
> + };
> +
> + pcie_eeprom_riser2: i2c@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <1>;
> +
> + eeprom@55 {
> + compatible = "atmel,24c512";
> + reg = <0x55>;
> + pagesize = <128>;
> + };
> + };
> +
> + pcie_eeprom_riser3: i2c@2 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <2>;
> +
> + eeprom@55 {
> + compatible = "atmel,24c512";
> + reg = <0x55>;
> + pagesize = <128>;
> + };
> + };
> + };
> +};
> +
> +&i2c12 {
> + status = "okay";
> +
> + psu0:psu0@58 {
> + compatible = "pmbus";
> + reg = <0x58>;
> + };
> +};
> +
> +&gpio0 {
> + status = "okay";
> + gpio-line-names =
> + /*A0-A7*/ "","","","","","","","",
> + /*B0-B7*/ "presence-ps0","power-chassis-good","","","","","presence-ps1","",
> + /*C0-C7*/ "","","","","","","","",
> + /*D0-D7*/ "","","","","","","","",
> + /*E0-E7*/ "","","","","","","","",
> + /*F0-F7*/ "","","","","power-chassis-control","","","",
> + /*G0-G7*/ "","","jtag-mux","","","","","",
> + /*H0-H7*/ "","","","","reset-button","power-button","","",
> + /*I0-I7*/ "","","","","","","","",
> + /*J0-J7*/ "","","","","","","","",
> + /*K0-K7*/ "","","","","","","","",
> + /*L0-L7*/ "","","","","","","","",
> + /*M0-M7*/ "","","","","","","","",
> + /*N0-N7*/ "","","","","","","","",
> + /*O0-O7*/ "","","","","","","","",
> + /*P0-P7*/ "","","","tck-mux","","","","",
> + /*Q0-Q7*/ "","","","","","","","",
> + /*R0-R7*/ "","","","","","","","",
> + /*S0-S7*/ "","","","","","","","",
> + /*T0-T7*/ "","","","","","","","",
> + /*U0-U7*/ "","nmi-button","","","","","","",
> + /*V0-V7*/ "","","","","power-config-full-load","","","",
> + /*W0-W7*/ "","","","","","","","",
> + /*X0-X7*/ "","","","","","","","",
> + /*Y0-Y7*/ "","","","","","","","",
> + /*Z0-Z7*/ "","","","","","","","",
> + /*AA0-AA7*/ "","","","","","","","",
> + /*AB0-AB7*/ "","","","","","","","",
> + /*AC0-AC7*/ "","","","","","","","";
> +};
> +
> +&lpc_snoop {
> + status = "okay";
> + snoop-ports = <0x80>;
> +};
> +
> +&emmc_controller {
> + status = "okay";
> +};
> +
> +&emmc {
> + status = "okay";
> + non-removable;
> + max-frequency = <52000000>;
> + bus-width = <8>;
> +};
> +
> +&vhub {
> + status = "okay";
> + aspeed,vhub-downstream-ports = <7>;
> + aspeed,vhub-generic-endpoints = <21>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usb2ad_default>;
> +};
> +
> +&rtc {
> + status = "okay";
> +};
> --
> 2.33.0
>
next prev parent reply other threads:[~2021-10-18 23:44 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <3a7fed78df06416da20ec72f14111c97@inventec.com>
2021-10-14 2:31 ` [PATCH v2] ARM: dts: aspeed: Adding Inventec Transformers BMC Lin.TommySC 林世欽 TAO
2021-10-18 23:43 ` Joel Stanley [this message]
2021-10-18 23:48 ` Joel Stanley
2021-10-19 2:06 ` Lin.TommySC 林世欽 TAO
2021-10-19 2:10 ` Joel Stanley
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CACPK8XeZ9esWimkv+RbeP3xyohzcPiUkXFhDWqB6ANjJ0aBvHw@mail.gmail.com \
--to=joel@jms.id.au \
--cc=Lin.TommySC@inventec.com \
--cc=mohammed.habeeb@inventec.com \
--cc=openbmc@lists.ozlabs.org \
--cc=ye.vic@inventec.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).