From: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
To: linux-media@vger.kernel.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, devel@driverdev.osuosl.org,
linux-sunxi@googlegroups.com
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Maxime Ripard <mripard@kernel.org>, Chen-Yu Tsai <wens@csie.org>,
Yong Deng <yong.deng@magewell.com>,
Kishon Vijay Abraham I <kishon@ti.com>,
Vinod Koul <vkoul@kernel.org>,
Helen Koike <helen.koike@collabora.com>,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Philipp Zabel <p.zabel@pengutronix.de>,
Paul Kocialkowski <paul.kocialkowski@bootlin.com>,
Hans Verkuil <hans.verkuil@cisco.com>,
Sakari Ailus <sakari.ailus@linux.intel.com>,
Thomas Petazzoni <thomas.petazzoni@bootlin.com>,
Hans Verkuil <hverkuil@xs4all.nl>,
kevin.lhopital@hotmail.com
Subject: [PATCH 01/14] phy: Distinguish between Rx and Tx for MIPI D-PHY with submodes
Date: Fri, 23 Oct 2020 19:45:33 +0200 [thread overview]
Message-ID: <20201023174546.504028-2-paul.kocialkowski@bootlin.com> (raw)
In-Reply-To: <20201023174546.504028-1-paul.kocialkowski@bootlin.com>
As some D-PHY controllers support both Rx and Tx mode, we need a way for
users to explicitly request one or the other. For instance, Rx mode can
be used along with MIPI CSI-2 while Tx mode can be used with MIPI DSI.
Introduce new MIPI D-PHY PHY submodes to use with PHY_MODE_MIPI_DPHY.
The default (zero value) is kept to Tx so only the rkisp1 driver, which
uses D-PHY in Rx mode, needs to be adapted.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
---
drivers/staging/media/rkisp1/rkisp1-isp.c | 3 ++-
include/linux/phy/phy-mipi-dphy.h | 13 +++++++++++++
2 files changed, 15 insertions(+), 1 deletion(-)
diff --git a/drivers/staging/media/rkisp1/rkisp1-isp.c b/drivers/staging/media/rkisp1/rkisp1-isp.c
index 6ec1e9816e9f..0afbce00121e 100644
--- a/drivers/staging/media/rkisp1/rkisp1-isp.c
+++ b/drivers/staging/media/rkisp1/rkisp1-isp.c
@@ -902,7 +902,8 @@ static int rkisp1_mipi_csi2_start(struct rkisp1_isp *isp,
phy_mipi_dphy_get_default_config(pixel_clock, isp->sink_fmt->bus_width,
sensor->lanes, cfg);
- phy_set_mode(sensor->dphy, PHY_MODE_MIPI_DPHY);
+ phy_set_mode_ext(cdev->dphy, PHY_MODE_MIPI_DPHY,
+ PHY_MIPI_DPHY_SUBMODE_RX);
phy_configure(sensor->dphy, &opts);
phy_power_on(sensor->dphy);
diff --git a/include/linux/phy/phy-mipi-dphy.h b/include/linux/phy/phy-mipi-dphy.h
index a877ffee845d..0f57ef46a8b5 100644
--- a/include/linux/phy/phy-mipi-dphy.h
+++ b/include/linux/phy/phy-mipi-dphy.h
@@ -6,6 +6,19 @@
#ifndef __PHY_MIPI_DPHY_H_
#define __PHY_MIPI_DPHY_H_
+/**
+ * enum phy_mipi_dphy_submode - MIPI D-PHY sub-mode
+ *
+ * A MIPI D-PHY can be used to transmit or receive data.
+ * Since some controllers can support both, the direction to enable is specified
+ * with the PHY sub-mode. Transmit is assumed by default with phy_set_mode.
+ */
+
+enum phy_mipi_dphy_submode {
+ PHY_MIPI_DPHY_SUBMODE_TX = 0,
+ PHY_MIPI_DPHY_SUBMODE_RX,
+};
+
/**
* struct phy_configure_opts_mipi_dphy - MIPI D-PHY configuration set
*
--
2.28.0
next prev parent reply other threads:[~2020-10-23 18:13 UTC|newest]
Thread overview: 66+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-10-23 17:45 [PATCH 00/14] Allwinner MIPI CSI-2 support for A31/V3s/A83T Paul Kocialkowski
2020-10-23 17:45 ` Paul Kocialkowski [this message]
2020-10-23 18:18 ` [linux-sunxi] [PATCH 01/14] phy: Distinguish between Rx and Tx for MIPI D-PHY with submodes Jernej Škrabec
2020-10-24 8:31 ` Paul Kocialkowski
2020-10-30 22:44 ` Helen Koike
2020-10-23 17:45 ` [PATCH 02/14] phy: allwinner: phy-sun6i-mipi-dphy: Support D-PHY Rx mode for MIPI CSI-2 Paul Kocialkowski
2020-10-26 15:38 ` Maxime Ripard
2020-10-27 9:23 ` Paul Kocialkowski
2020-10-27 18:28 ` Maxime Ripard
2020-11-04 10:53 ` Paul Kocialkowski
2020-10-30 22:44 ` Helen Koike
2020-11-04 10:54 ` Paul Kocialkowski
2020-10-23 17:45 ` [PATCH 03/14] media: sun6i-csi: Support an optional dedicated memory pool Paul Kocialkowski
2020-10-26 15:41 ` Maxime Ripard
2020-10-27 9:26 ` Paul Kocialkowski
2020-10-23 17:45 ` [PATCH 04/14] media: sun6i-csi: Fix the image storage bpp for 10/12-bit Bayer formats Paul Kocialkowski
2020-10-30 22:45 ` Helen Koike
2020-11-04 10:56 ` Paul Kocialkowski
2020-10-23 17:45 ` [PATCH 05/14] media: sun6i-csi: Only configure the interface data width for parallel Paul Kocialkowski
2020-10-26 16:00 ` Maxime Ripard
2020-10-27 9:31 ` Paul Kocialkowski
2020-10-27 18:31 ` Maxime Ripard
2020-10-23 17:45 ` [PATCH 06/14] media: sun6i-csi: Support feeding from the MIPI CSI-2 controller Paul Kocialkowski
2020-10-23 17:45 ` [PATCH 07/14] dt-bindings: media: i2c: Add A31 MIPI CSI-2 bindings documentation Paul Kocialkowski
2020-10-26 16:14 ` Maxime Ripard
2020-10-27 9:52 ` Paul Kocialkowski
2020-10-27 18:44 ` Maxime Ripard
2020-11-04 10:48 ` Paul Kocialkowski
2020-11-04 16:53 ` Maxime Ripard
2020-10-30 16:33 ` Rob Herring
2020-10-30 16:56 ` Sakari Ailus
2020-10-23 17:45 ` [PATCH 08/14] media: sunxi: Add support for the A31 MIPI CSI-2 controller Paul Kocialkowski
2020-10-26 8:39 ` Dan Carpenter
2020-10-26 16:54 ` Maxime Ripard
2020-11-04 11:34 ` Paul Kocialkowski
2020-11-04 18:56 ` Maxime Ripard
2020-11-05 14:52 ` Paul Kocialkowski
2020-10-30 22:45 ` Helen Koike
2020-11-02 9:21 ` Maxime Ripard
2020-11-04 11:17 ` Paul Kocialkowski
2020-11-04 16:38 ` Helen Koike
2020-11-04 18:45 ` Maxime Ripard
2020-11-05 14:14 ` Helen Koike
2020-11-05 8:45 ` Sakari Ailus
2020-11-05 14:55 ` Paul Kocialkowski
2020-10-23 17:45 ` [PATCH 09/14] ARM: dts: sun8i: v3s: Add CSI0 camera interface node Paul Kocialkowski
2020-10-23 17:45 ` [PATCH 10/14] ARM: dts: sun8i: v3s: Add MIPI D-PHY and MIPI CSI-2 interface nodes Paul Kocialkowski
2020-10-26 16:55 ` Maxime Ripard
2020-10-23 17:45 ` [PATCH 11/14] dt-bindings: media: i2c: Add A83T MIPI CSI-2 bindings documentation Paul Kocialkowski
2020-10-26 16:56 ` Maxime Ripard
2020-11-04 10:33 ` Paul Kocialkowski
2020-11-05 8:48 ` Sakari Ailus
2020-10-23 17:45 ` [PATCH 12/14] media: sunxi: Add support for the A83T MIPI CSI-2 controller Paul Kocialkowski
2020-10-26 8:53 ` Dan Carpenter
2020-10-26 17:00 ` Maxime Ripard
2020-11-04 10:37 ` Paul Kocialkowski
2020-10-23 17:45 ` [PATCH 13/14] ARM: dts: sun8i: a83t: Add MIPI CSI-2 controller node Paul Kocialkowski
2020-10-23 17:45 ` [PATCH 14/14] media: sunxi: sun8i-a83t-mipi-csi2: Avoid using the (unsolicited) interrupt Paul Kocialkowski
2020-10-26 16:57 ` Maxime Ripard
2020-10-26 17:20 ` [PATCH 00/14] Allwinner MIPI CSI-2 support for A31/V3s/A83T Maxime Ripard
2020-10-30 22:44 ` Helen Koike
2020-11-02 9:17 ` Maxime Ripard
2020-11-04 11:11 ` Paul Kocialkowski
2020-11-04 11:14 ` Paul Kocialkowski
2020-11-04 16:36 ` Helen Koike
2020-11-05 14:58 ` Paul Kocialkowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201023174546.504028-2-paul.kocialkowski@bootlin.com \
--to=paul.kocialkowski@bootlin.com \
--cc=devel@driverdev.osuosl.org \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=hans.verkuil@cisco.com \
--cc=helen.koike@collabora.com \
--cc=hverkuil@xs4all.nl \
--cc=kevin.lhopital@hotmail.com \
--cc=kishon@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=linux-sunxi@googlegroups.com \
--cc=mchehab@kernel.org \
--cc=mripard@kernel.org \
--cc=p.zabel@pengutronix.de \
--cc=robh+dt@kernel.org \
--cc=sakari.ailus@linux.intel.com \
--cc=thomas.petazzoni@bootlin.com \
--cc=vkoul@kernel.org \
--cc=wens@csie.org \
--cc=yong.deng@magewell.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).