From: Kuldeep Singh <kuldeep.singh@nxp.com>
To: linux-spi@vger.kernel.org, linux-kernel@vger.kernel.org
Cc: Ashish Kumar <ashish.kumar@nxp.com>,
Mark Brown <broonie@kernel.org>,
Kuldeep Singh <kuldeep.singh@nxp.com>
Subject: [PATCH 1/3] spi: spi-nxp-fspi: Add support for IP read only
Date: Mon, 1 Mar 2021 16:02:28 +0530 [thread overview]
Message-ID: <20210301103230.1816168-2-kuldeep.singh@nxp.com> (raw)
In-Reply-To: <20210301103230.1816168-1-kuldeep.singh@nxp.com>
Add support for disabling AHB bus and read entire flash contents via IP
only. Please note, this enables IP bus read using a quirk which can be
enabled directly in device-type data or in existence of an errata where
AHB bus may need to be disabled.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
---
drivers/spi/spi-nxp-fspi.c | 28 ++++++++++++++++++++++------
1 file changed, 22 insertions(+), 6 deletions(-)
diff --git a/drivers/spi/spi-nxp-fspi.c b/drivers/spi/spi-nxp-fspi.c
index ab9035662717..829391e20e92 100644
--- a/drivers/spi/spi-nxp-fspi.c
+++ b/drivers/spi/spi-nxp-fspi.c
@@ -311,6 +311,9 @@
#define NXP_FSPI_MAX_CHIPSELECT 4
#define NXP_FSPI_MIN_IOMAP SZ_4M
+/* Access flash memory using IP bus only */
+#define FSPI_QUIRK_USE_IP_ONLY BIT(0)
+
struct nxp_fspi_devtype_data {
unsigned int rxfifo;
unsigned int txfifo;
@@ -359,6 +362,11 @@ struct nxp_fspi {
int selected;
};
+static inline int needs_ip_only(struct nxp_fspi *f)
+{
+ return f->devtype_data->quirks & FSPI_QUIRK_USE_IP_ONLY;
+}
+
/*
* R/W functions for big- or little-endian registers:
* The FSPI controller's endianness is independent of
@@ -553,8 +561,8 @@ static void nxp_fspi_prepare_lut(struct nxp_fspi *f,
for (i = 0; i < ARRAY_SIZE(lutval); i++)
fspi_writel(f, lutval[i], base + FSPI_LUT_REG(i));
- dev_dbg(f->dev, "CMD[%x] lutval[0:%x \t 1:%x \t 2:%x \t 3:%x]\n",
- op->cmd.opcode, lutval[0], lutval[1], lutval[2], lutval[3]);
+ dev_dbg(f->dev, "CMD[%x] lutval[0:%x \t 1:%x \t 2:%x \t 3:%x], size: 0x%08x\n",
+ op->cmd.opcode, lutval[0], lutval[1], lutval[2], lutval[3], op->data.nbytes);
/* lock LUT */
fspi_writel(f, FSPI_LUTKEY_VALUE, f->iobase + FSPI_LUTKEY);
@@ -852,12 +860,14 @@ static int nxp_fspi_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
nxp_fspi_prepare_lut(f, op);
/*
- * If we have large chunks of data, we read them through the AHB bus
- * by accessing the mapped memory. In all other cases we use
- * IP commands to access the flash.
+ * If we have large chunks of data, we read them through the AHB bus by
+ * accessing the mapped memory. In all other cases we use IP commands
+ * to access the flash. Read via AHB bus may be corrupted due to
+ * existence of an errata and therefore discard AHB read in such cases.
*/
if (op->data.nbytes > (f->devtype_data->rxfifo - 4) &&
- op->data.dir == SPI_MEM_DATA_IN) {
+ op->data.dir == SPI_MEM_DATA_IN &&
+ !needs_ip_only(f)) {
err = nxp_fspi_read_ahb(f, op);
} else {
if (op->data.nbytes && op->data.dir == SPI_MEM_DATA_OUT)
@@ -888,6 +898,12 @@ static int nxp_fspi_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op)
op->data.nbytes = ALIGN_DOWN(op->data.nbytes, 8);
}
+ /* Limit data bytes to RX FIFO in case of IP read only */
+ if (op->data.dir == SPI_MEM_DATA_IN &&
+ needs_ip_only(f) &&
+ op->data.nbytes > f->devtype_data->rxfifo)
+ op->data.nbytes = f->devtype_data->rxfifo;
+
return 0;
}
--
2.25.1
next prev parent reply other threads:[~2021-03-01 10:38 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-03-01 10:32 [PATCH 0/3] NXP Flexspi driver patches Kuldeep Singh
2021-03-01 10:32 ` Kuldeep Singh [this message]
2021-03-01 10:32 ` [PATCH 2/3] spi: spi-nxp-fspi: Add driver support for imx8dxl Kuldeep Singh
2021-03-01 13:25 ` Mark Brown
2021-03-01 16:39 ` [EXT] " Kuldeep Singh
2021-03-01 17:11 ` Mark Brown
2021-03-02 5:19 ` Kuldeep Singh
2021-03-01 10:32 ` [PATCH 3/3] spi: spi-nxp-fspi: Implement errata workaround for LS1028A Kuldeep Singh
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210301103230.1816168-2-kuldeep.singh@nxp.com \
--to=kuldeep.singh@nxp.com \
--cc=ashish.kumar@nxp.com \
--cc=broonie@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-spi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).