* [Qemu-devel] [Bug 1511887] Re: USB device 1.1 not correctly passedthru from Linux host to Windows guest
2015-10-31 0:23 [Qemu-devel] [Bug 1511887] [NEW] USB device 1.1 not correctly passedthru from Linux host to Windows guest Jiri Cejka
@ 2017-05-19 10:32 ` Thomas Huth
2017-05-19 11:26 ` Jiri Cejka
` (4 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Thomas Huth @ 2017-05-19 10:32 UTC (permalink / raw)
To: qemu-devel
Triaging old bug tickets ... can you still reproduce this issue with the
latest version of QEMU (currently v2.9)?
** Changed in: qemu
Status: New => Incomplete
--
You received this bug notification because you are a member of qemu-
devel-ml, which is subscribed to QEMU.
https://bugs.launchpad.net/bugs/1511887
Title:
USB device 1.1 not correctly passedthru from Linux host to Windows
guest
Status in QEMU:
Incomplete
Bug description:
I have USB Digital Oscilloscope which works great on pure Windows
machine but not work on virtualized one. I tried passthru the device
from my Debian Jessie (64bit) host machine to Windows 7 (32bit) guest
machine but unfortunately it does not work very well. It looks that
device is passed thru so Windows machine knows about new device and
loads HID device driver for it but the device driver failed to start
the device and details of an error provided by device manager is "This
device cannot start" Code 10.
Installed Qemu version: 2.1+dfsg-12+deb8u4 0
USB device spec: Dynon Instruments ELAB-080, USB 1.1
On linux host computer
---------------------------
lsusb identify it as:
Bus 003 Device 009: ID 13a3:0001
lsusb -t identify it as:
/: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=uhci_hcd/2p, 12M
|__ Port 1: Dev 9, If 0, Class=Human Interface Device, Driver=usbhid, 12M
This is how I started my Windows guest machine
------------------------------------------------------
kvm -cpu host \
-m 2048MiB \
-hda test.vdi \
-ctrl-grab \
-parallel /dev/parport0 \
-usbdevice host:13a3:0001
...also instead of last line I tried this one:
-device usb-host,vendorid=0x13a3,productid=0x0001
none of them help to properly handle my device inside guest machine.
Only one time the Windows guest machine properly start the device so
software for that oscilloscope can identify the Oscilloscope and
measure for a while but unfortunately after I guess 5 seconds of
measurement the device was disconnected from Windows and never start
working again even after couple of restarts of guest machine even
after plug and unplug it's USB cable and power cable.
I searched for a solution or some clues to get it work but none of my
searching over the internet was successful. Because device works on
pure Windows but not work on virtualized one, I think there is a
problem with handling not standard USB devices (like sticks,
keyboards, mouses etc.)
To manage notifications about this bug go to:
https://bugs.launchpad.net/qemu/+bug/1511887/+subscriptions
^ permalink raw reply [flat|nested] 7+ messages in thread* [Qemu-devel] [Bug 1511887] Re: USB device 1.1 not correctly passedthru from Linux host to Windows guest
2015-10-31 0:23 [Qemu-devel] [Bug 1511887] [NEW] USB device 1.1 not correctly passedthru from Linux host to Windows guest Jiri Cejka
2017-05-19 10:32 ` [Qemu-devel] [Bug 1511887] " Thomas Huth
@ 2017-05-19 11:26 ` Jiri Cejka
2017-05-19 12:44 ` Thomas Huth
` (3 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Jiri Cejka @ 2017-05-19 11:26 UTC (permalink / raw)
To: qemu-devel
Currently I can reproduce this bug with 2.8+dfsg-3~bpo8+1 version
because I'm using stable Debian GNU/Linux. I'll try install latest qemu
test it and report back here.
--
You received this bug notification because you are a member of qemu-
devel-ml, which is subscribed to QEMU.
https://bugs.launchpad.net/bugs/1511887
Title:
USB device 1.1 not correctly passedthru from Linux host to Windows
guest
Status in QEMU:
Incomplete
Bug description:
I have USB Digital Oscilloscope which works great on pure Windows
machine but not work on virtualized one. I tried passthru the device
from my Debian Jessie (64bit) host machine to Windows 7 (32bit) guest
machine but unfortunately it does not work very well. It looks that
device is passed thru so Windows machine knows about new device and
loads HID device driver for it but the device driver failed to start
the device and details of an error provided by device manager is "This
device cannot start" Code 10.
Installed Qemu version: 2.1+dfsg-12+deb8u4 0
USB device spec: Dynon Instruments ELAB-080, USB 1.1
On linux host computer
---------------------------
lsusb identify it as:
Bus 003 Device 009: ID 13a3:0001
lsusb -t identify it as:
/: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=uhci_hcd/2p, 12M
|__ Port 1: Dev 9, If 0, Class=Human Interface Device, Driver=usbhid, 12M
This is how I started my Windows guest machine
------------------------------------------------------
kvm -cpu host \
-m 2048MiB \
-hda test.vdi \
-ctrl-grab \
-parallel /dev/parport0 \
-usbdevice host:13a3:0001
...also instead of last line I tried this one:
-device usb-host,vendorid=0x13a3,productid=0x0001
none of them help to properly handle my device inside guest machine.
Only one time the Windows guest machine properly start the device so
software for that oscilloscope can identify the Oscilloscope and
measure for a while but unfortunately after I guess 5 seconds of
measurement the device was disconnected from Windows and never start
working again even after couple of restarts of guest machine even
after plug and unplug it's USB cable and power cable.
I searched for a solution or some clues to get it work but none of my
searching over the internet was successful. Because device works on
pure Windows but not work on virtualized one, I think there is a
problem with handling not standard USB devices (like sticks,
keyboards, mouses etc.)
To manage notifications about this bug go to:
https://bugs.launchpad.net/qemu/+bug/1511887/+subscriptions
^ permalink raw reply [flat|nested] 7+ messages in thread* [Qemu-devel] [Bug 1511887] Re: USB device 1.1 not correctly passedthru from Linux host to Windows guest
2015-10-31 0:23 [Qemu-devel] [Bug 1511887] [NEW] USB device 1.1 not correctly passedthru from Linux host to Windows guest Jiri Cejka
2017-05-19 10:32 ` [Qemu-devel] [Bug 1511887] " Thomas Huth
2017-05-19 11:26 ` Jiri Cejka
@ 2017-05-19 12:44 ` Thomas Huth
2017-06-16 11:30 ` Jiri Cejka
` (2 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Thomas Huth @ 2017-05-19 12:44 UTC (permalink / raw)
To: qemu-devel
** Changed in: qemu
Status: Incomplete => Triaged
--
You received this bug notification because you are a member of qemu-
devel-ml, which is subscribed to QEMU.
https://bugs.launchpad.net/bugs/1511887
Title:
USB device 1.1 not correctly passedthru from Linux host to Windows
guest
Status in QEMU:
Triaged
Bug description:
I have USB Digital Oscilloscope which works great on pure Windows
machine but not work on virtualized one. I tried passthru the device
from my Debian Jessie (64bit) host machine to Windows 7 (32bit) guest
machine but unfortunately it does not work very well. It looks that
device is passed thru so Windows machine knows about new device and
loads HID device driver for it but the device driver failed to start
the device and details of an error provided by device manager is "This
device cannot start" Code 10.
Installed Qemu version: 2.1+dfsg-12+deb8u4 0
USB device spec: Dynon Instruments ELAB-080, USB 1.1
On linux host computer
---------------------------
lsusb identify it as:
Bus 003 Device 009: ID 13a3:0001
lsusb -t identify it as:
/: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=uhci_hcd/2p, 12M
|__ Port 1: Dev 9, If 0, Class=Human Interface Device, Driver=usbhid, 12M
This is how I started my Windows guest machine
------------------------------------------------------
kvm -cpu host \
-m 2048MiB \
-hda test.vdi \
-ctrl-grab \
-parallel /dev/parport0 \
-usbdevice host:13a3:0001
...also instead of last line I tried this one:
-device usb-host,vendorid=0x13a3,productid=0x0001
none of them help to properly handle my device inside guest machine.
Only one time the Windows guest machine properly start the device so
software for that oscilloscope can identify the Oscilloscope and
measure for a while but unfortunately after I guess 5 seconds of
measurement the device was disconnected from Windows and never start
working again even after couple of restarts of guest machine even
after plug and unplug it's USB cable and power cable.
I searched for a solution or some clues to get it work but none of my
searching over the internet was successful. Because device works on
pure Windows but not work on virtualized one, I think there is a
problem with handling not standard USB devices (like sticks,
keyboards, mouses etc.)
To manage notifications about this bug go to:
https://bugs.launchpad.net/qemu/+bug/1511887/+subscriptions
^ permalink raw reply [flat|nested] 7+ messages in thread* [Qemu-devel] [Bug 1511887] Re: USB device 1.1 not correctly passedthru from Linux host to Windows guest
2015-10-31 0:23 [Qemu-devel] [Bug 1511887] [NEW] USB device 1.1 not correctly passedthru from Linux host to Windows guest Jiri Cejka
` (2 preceding siblings ...)
2017-05-19 12:44 ` Thomas Huth
@ 2017-06-16 11:30 ` Jiri Cejka
2018-12-18 7:23 ` Johansen
2021-05-04 7:23 ` Thomas Huth
5 siblings, 0 replies; 7+ messages in thread
From: Jiri Cejka @ 2017-06-16 11:30 UTC (permalink / raw)
To: qemu-devel
In commnet #2 I promised to do test with latest qemu 2.9. I'm back here
to report what I've done and what's my findings.
1) I've downloaded newest Qemu 2.9.0 released at Apr 20 2017 from qemu.org website.
2) I've compiled it on fully updated Debian Jessie using following extra parameters: ../configure --enable-kvm --enable-libusb and then make
3) I tried to start my Windows guest machine using following command:
x86_64-softmmu/qemu-system-x86_64 \
-enable-kvm \
-M q35,accel=kvm \
-m 2048 \
-cpu host \
-hda test.vdi \
-usb \
-device usb-host,vendorid=0x13a3,productid=0x0001
After Windows guest started I plugged in my USB Oscilloscope and get the
same result in Windows Device Manager: "This device cannot start" Code
10. The result is completely the same as before.
4) In terminal I got following errors:
libusb: error [_open_sysfs_attr] open /sys/bus/usb/devices/2-1/bConfigurationValue failed ret=-1 errno=2
libusb: error [op_set_configuration] failed, error -1 errno 71
qemu-system-x86_64: libusb_set_configuration: -99 [OTHER]
NOTE: libusb-dev version used during compile was 1.0.19-1
RESULT: I can confirm and can reproduce for sure that the problem
persist also in newest Qemu 2.9.0.
--
You received this bug notification because you are a member of qemu-
devel-ml, which is subscribed to QEMU.
https://bugs.launchpad.net/bugs/1511887
Title:
USB device 1.1 not correctly passedthru from Linux host to Windows
guest
Status in QEMU:
Triaged
Bug description:
I have USB Digital Oscilloscope which works great on pure Windows
machine but not work on virtualized one. I tried passthru the device
from my Debian Jessie (64bit) host machine to Windows 7 (32bit) guest
machine but unfortunately it does not work very well. It looks that
device is passed thru so Windows machine knows about new device and
loads HID device driver for it but the device driver failed to start
the device and details of an error provided by device manager is "This
device cannot start" Code 10.
Installed Qemu version: 2.1+dfsg-12+deb8u4 0
USB device spec: Dynon Instruments ELAB-080, USB 1.1
On linux host computer
---------------------------
lsusb identify it as:
Bus 003 Device 009: ID 13a3:0001
lsusb -t identify it as:
/: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=uhci_hcd/2p, 12M
|__ Port 1: Dev 9, If 0, Class=Human Interface Device, Driver=usbhid, 12M
This is how I started my Windows guest machine
------------------------------------------------------
kvm -cpu host \
-m 2048MiB \
-hda test.vdi \
-ctrl-grab \
-parallel /dev/parport0 \
-usbdevice host:13a3:0001
...also instead of last line I tried this one:
-device usb-host,vendorid=0x13a3,productid=0x0001
none of them help to properly handle my device inside guest machine.
Only one time the Windows guest machine properly start the device so
software for that oscilloscope can identify the Oscilloscope and
measure for a while but unfortunately after I guess 5 seconds of
measurement the device was disconnected from Windows and never start
working again even after couple of restarts of guest machine even
after plug and unplug it's USB cable and power cable.
I searched for a solution or some clues to get it work but none of my
searching over the internet was successful. Because device works on
pure Windows but not work on virtualized one, I think there is a
problem with handling not standard USB devices (like sticks,
keyboards, mouses etc.)
To manage notifications about this bug go to:
https://bugs.launchpad.net/qemu/+bug/1511887/+subscriptions
^ permalink raw reply [flat|nested] 7+ messages in thread* [Qemu-devel] [Bug 1511887] Re: USB device 1.1 not correctly passedthru from Linux host to Windows guest
2015-10-31 0:23 [Qemu-devel] [Bug 1511887] [NEW] USB device 1.1 not correctly passedthru from Linux host to Windows guest Jiri Cejka
` (3 preceding siblings ...)
2017-06-16 11:30 ` Jiri Cejka
@ 2018-12-18 7:23 ` Johansen
2021-05-04 7:23 ` Thomas Huth
5 siblings, 0 replies; 7+ messages in thread
From: Johansen @ 2018-12-18 7:23 UTC (permalink / raw)
To: qemu-devel
** Also affects: wine1.6 (Ubuntu)
Importance: Undecided
Status: New
--
You received this bug notification because you are a member of qemu-
devel-ml, which is subscribed to QEMU.
https://bugs.launchpad.net/bugs/1511887
Title:
USB device 1.1 not correctly passedthru from Linux host to Windows
guest
Status in QEMU:
Triaged
Status in wine1.6 package in Ubuntu:
New
Bug description:
I have USB Digital Oscilloscope which works great on pure Windows
machine but not work on virtualized one. I tried passthru the device
from my Debian Jessie (64bit) host machine to Windows 7 (32bit) guest
machine but unfortunately it does not work very well. It looks that
device is passed thru so Windows machine knows about new device and
loads HID device driver for it but the device driver failed to start
the device and details of an error provided by device manager is "This
device cannot start" Code 10.
Installed Qemu version: 2.1+dfsg-12+deb8u4 0
USB device spec: Dynon Instruments ELAB-080, USB 1.1
On linux host computer
---------------------------
lsusb identify it as:
Bus 003 Device 009: ID 13a3:0001
lsusb -t identify it as:
/: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=uhci_hcd/2p, 12M
|__ Port 1: Dev 9, If 0, Class=Human Interface Device, Driver=usbhid, 12M
This is how I started my Windows guest machine
------------------------------------------------------
kvm -cpu host \
-m 2048MiB \
-hda test.vdi \
-ctrl-grab \
-parallel /dev/parport0 \
-usbdevice host:13a3:0001
...also instead of last line I tried this one:
-device usb-host,vendorid=0x13a3,productid=0x0001
none of them help to properly handle my device inside guest machine.
Only one time the Windows guest machine properly start the device so
software for that oscilloscope can identify the Oscilloscope and
measure for a while but unfortunately after I guess 5 seconds of
measurement the device was disconnected from Windows and never start
working again even after couple of restarts of guest machine even
after plug and unplug it's USB cable and power cable.
I searched for a solution or some clues to get it work but none of my
searching over the internet was successful. Because device works on
pure Windows but not work on virtualized one, I think there is a
problem with handling not standard USB devices (like sticks,
keyboards, mouses etc.)
To manage notifications about this bug go to:
https://bugs.launchpad.net/qemu/+bug/1511887/+subscriptions
^ permalink raw reply [flat|nested] 7+ messages in thread* [Bug 1511887] Re: USB device 1.1 not correctly passedthru from Linux host to Windows guest
2015-10-31 0:23 [Qemu-devel] [Bug 1511887] [NEW] USB device 1.1 not correctly passedthru from Linux host to Windows guest Jiri Cejka
` (4 preceding siblings ...)
2018-12-18 7:23 ` Johansen
@ 2021-05-04 7:23 ` Thomas Huth
5 siblings, 0 replies; 7+ messages in thread
From: Thomas Huth @ 2021-05-04 7:23 UTC (permalink / raw)
To: qemu-devel
This is an automated cleanup. This bug report has been moved to QEMU's
new bug tracker on gitlab.com and thus gets marked as 'expired' now.
Please continue with the discussion here:
https://gitlab.com/qemu-project/qemu/-/issues/118
** Changed in: qemu
Status: Triaged => Expired
** Bug watch added: gitlab.com/qemu-project/qemu/-/issues #118
https://gitlab.com/qemu-project/qemu/-/issues/118
--
You received this bug notification because you are a member of qemu-
devel-ml, which is subscribed to QEMU.
https://bugs.launchpad.net/bugs/1511887
Title:
USB device 1.1 not correctly passedthru from Linux host to Windows
guest
Status in QEMU:
Expired
Status in wine1.6 package in Ubuntu:
New
Bug description:
I have USB Digital Oscilloscope which works great on pure Windows
machine but not work on virtualized one. I tried passthru the device
from my Debian Jessie (64bit) host machine to Windows 7 (32bit) guest
machine but unfortunately it does not work very well. It looks that
device is passed thru so Windows machine knows about new device and
loads HID device driver for it but the device driver failed to start
the device and details of an error provided by device manager is "This
device cannot start" Code 10.
Installed Qemu version: 2.1+dfsg-12+deb8u4 0
USB device spec: Dynon Instruments ELAB-080, USB 1.1
On linux host computer
---------------------------
lsusb identify it as:
Bus 003 Device 009: ID 13a3:0001
lsusb -t identify it as:
/: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=uhci_hcd/2p, 12M
|__ Port 1: Dev 9, If 0, Class=Human Interface Device, Driver=usbhid, 12M
This is how I started my Windows guest machine
------------------------------------------------------
kvm -cpu host \
-m 2048MiB \
-hda test.vdi \
-ctrl-grab \
-parallel /dev/parport0 \
-usbdevice host:13a3:0001
...also instead of last line I tried this one:
-device usb-host,vendorid=0x13a3,productid=0x0001
none of them help to properly handle my device inside guest machine.
Only one time the Windows guest machine properly start the device so
software for that oscilloscope can identify the Oscilloscope and
measure for a while but unfortunately after I guess 5 seconds of
measurement the device was disconnected from Windows and never start
working again even after couple of restarts of guest machine even
after plug and unplug it's USB cable and power cable.
I searched for a solution or some clues to get it work but none of my
searching over the internet was successful. Because device works on
pure Windows but not work on virtualized one, I think there is a
problem with handling not standard USB devices (like sticks,
keyboards, mouses etc.)
To manage notifications about this bug go to:
https://bugs.launchpad.net/qemu/+bug/1511887/+subscriptions
^ permalink raw reply [flat|nested] 7+ messages in thread