* [PATCH v6 0/3] Add support for TPM devices over I2C bus
@ 2023-03-26 2:38 Ninad Palsule
2023-03-26 2:38 ` [PATCH v6 1/3] docs: " Ninad Palsule
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: Ninad Palsule @ 2023-03-26 2:38 UTC (permalink / raw)
To: qemu-devel; +Cc: Ninad Palsule, joel, andrew, stefanb, clg
Hello,
I have incorporated review comments from Stefan. Please review.
This drop adds support for the TPM devices attached to the I2C bus. It
only supports the TPM2 protocol. You need to run it with the external
TPM emulator like swtpm. I have tested it with swtpm.
I have refered to the work done by zhdaniel@meta.com but at the core
level out implementation is different.
https://github.com/theopolis/qemu/commit/2e2e57cde9e419c36af8071bb85392ad1ed70966
Based-on: $MESSAGE_ID
Ninad Palsule (3):
docs: Add support for TPM devices over I2C bus
tpm: Extend common APIs to support TPM TIS I2C
tpm: Add support for TPM device over I2C bus
docs/specs/tpm.rst | 32 +++
hw/arm/Kconfig | 1 +
hw/tpm/Kconfig | 7 +
hw/tpm/meson.build | 1 +
hw/tpm/tpm_tis.h | 3 +
hw/tpm/tpm_tis_common.c | 28 +++
hw/tpm/tpm_tis_i2c.c | 533 ++++++++++++++++++++++++++++++++++++++++
hw/tpm/trace-events | 6 +
include/hw/acpi/tpm.h | 28 +++
include/sysemu/tpm.h | 3 +
10 files changed, 642 insertions(+)
create mode 100644 hw/tpm/tpm_tis_i2c.c
--
2.37.2
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v6 1/3] docs: Add support for TPM devices over I2C bus
2023-03-26 2:38 [PATCH v6 0/3] Add support for TPM devices over I2C bus Ninad Palsule
@ 2023-03-26 2:38 ` Ninad Palsule
2023-03-26 2:38 ` [PATCH v6 2/3] tpm: Extend common APIs to support TPM TIS I2C Ninad Palsule
2023-03-26 2:38 ` [PATCH v6 3/3] tpm: Add support for TPM device over I2C bus Ninad Palsule
2 siblings, 0 replies; 6+ messages in thread
From: Ninad Palsule @ 2023-03-26 2:38 UTC (permalink / raw)
To: qemu-devel; +Cc: Ninad Palsule, joel, andrew, stefanb, clg
This is a documentation change for I2C TPM device support.
Qemu already supports devices attached to ISA and sysbus.
This drop adds support for the I2C bus attached TPM devices.
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
---
V2:
Incorporated Stephen's review comments
- Added example in the document.
---
V4:
Incorporate Cedric & Stefan's comments
- Added example for ast2600-evb
- Corrected statement about arm virtual machine.
---
V6:
Incorporated review comments from Stefan.
---
docs/specs/tpm.rst | 32 ++++++++++++++++++++++++++++++++
1 file changed, 32 insertions(+)
diff --git a/docs/specs/tpm.rst b/docs/specs/tpm.rst
index 535912a92b..590e670a9a 100644
--- a/docs/specs/tpm.rst
+++ b/docs/specs/tpm.rst
@@ -21,12 +21,16 @@ QEMU files related to TPM TIS interface:
- ``hw/tpm/tpm_tis_common.c``
- ``hw/tpm/tpm_tis_isa.c``
- ``hw/tpm/tpm_tis_sysbus.c``
+ - ``hw/tpm/tpm_tis_i2c.c``
- ``hw/tpm/tpm_tis.h``
Both an ISA device and a sysbus device are available. The former is
used with pc/q35 machine while the latter can be instantiated in the
Arm virt machine.
+An I2C device support is also provided which can be instantiated in the Arm
+based emulation machines. This device only supports the TPM 2 protocol.
+
CRB interface
-------------
@@ -348,6 +352,34 @@ In case an Arm virt machine is emulated, use the following command line:
-drive if=pflash,format=raw,file=flash0.img,readonly=on \
-drive if=pflash,format=raw,file=flash1.img
+In case a ast2600-evb bmc machine is emulated and want to use TPM device
+attached to I2C bus, use the following command line:
+
+.. code-block:: console
+
+ qemu-system-arm -M ast2600-evb -nographic \
+ -kernel arch/arm/boot/zImage \
+ -dtb arch/arm/boot/dts/aspeed-ast2600-evb.dtb \
+ -initrd rootfs.cpio \
+ -chardev socket,id=chrtpm,path=/tmp/mytpm1/swtpm-sock \
+ -tpmdev emulator,id=tpm0,chardev=chrtpm \
+ -device tpm-tis-i2c,tpmdev=tpm0,bus=aspeed.i2c.bus.12,address=0x2e
+
+In case a Rainier bmc machine is emulated and want to use TPM device
+attached to I2C bus, use the following command line:
+
+.. code-block:: console
+
+ qemu-system-arm -M rainier-bmc -nographic \
+ -kernel ${IMAGEPATH}/fitImage-linux.bin \
+ -dtb ${IMAGEPATH}/aspeed-bmc-ibm-rainier.dtb \
+ -initrd ${IMAGEPATH}/obmc-phosphor-initramfs.rootfs.cpio.xz \
+ -drive file=${IMAGEPATH}/obmc-phosphor-image.rootfs.wic.qcow2,if=sd,index=2\
+ -net nic -net user,hostfwd=:127.0.0.1:2222-:22,hostfwd=:127.0.0.1:2443-:443\
+ -chardev socket,id=chrtpm,path=/tmp/mytpm1/swtpm-sock \
+ -tpmdev emulator,id=tpm0,chardev=chrtpm \
+ -device tpm-tis-i2c,tpmdev=tpm0,bus=aspeed.i2c.bus.12,address=0x2e
+
In case SeaBIOS is used as firmware, it should show the TPM menu item
after entering the menu with 'ESC'.
--
2.37.2
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v6 2/3] tpm: Extend common APIs to support TPM TIS I2C
2023-03-26 2:38 [PATCH v6 0/3] Add support for TPM devices over I2C bus Ninad Palsule
2023-03-26 2:38 ` [PATCH v6 1/3] docs: " Ninad Palsule
@ 2023-03-26 2:38 ` Ninad Palsule
2023-03-26 2:38 ` [PATCH v6 3/3] tpm: Add support for TPM device over I2C bus Ninad Palsule
2 siblings, 0 replies; 6+ messages in thread
From: Ninad Palsule @ 2023-03-26 2:38 UTC (permalink / raw)
To: qemu-devel; +Cc: Ninad Palsule, joel, andrew, stefanb, clg
Qemu already supports devices attached to ISA and sysbus. This drop adds
support for the I2C bus attached TPM devices.
This commit includes changes for the common code.
- Added support for the new checksum registers which are required for
the I2C support. The checksum calculation is handled in the qemu
common code.
- Added wrapper function for read and write data so that I2C code can
call it without MMIO interface.
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
---
V2:
Incorporated Stephen's comments.
- Removed checksum enable and checksum get registers.
- Added checksum calculation function which can be called from
i2c layer.
---
V3:
Incorporated review comments from Cedric and Stefan.
- Pass locality to the checksum calculation function and cleanup
- Moved I2C related definations in the acpi/tpm.h
---
V4:
Incorporated review comments by Stefan
- Remove the check for locality while calculating checksum
- Use bswap16 instead of cpu_ti_be16.
- Rename TPM_I2C register by dropping _TIS_ from it.
---
hw/tpm/tpm_tis.h | 3 +++
hw/tpm/tpm_tis_common.c | 28 ++++++++++++++++++++++++++++
include/hw/acpi/tpm.h | 28 ++++++++++++++++++++++++++++
3 files changed, 59 insertions(+)
diff --git a/hw/tpm/tpm_tis.h b/hw/tpm/tpm_tis.h
index f6b5872ba6..6f29a508dd 100644
--- a/hw/tpm/tpm_tis.h
+++ b/hw/tpm/tpm_tis.h
@@ -86,5 +86,8 @@ int tpm_tis_pre_save(TPMState *s);
void tpm_tis_reset(TPMState *s);
enum TPMVersion tpm_tis_get_tpm_version(TPMState *s);
void tpm_tis_request_completed(TPMState *s, int ret);
+uint32_t tpm_tis_read_data(TPMState *s, hwaddr addr, unsigned size);
+void tpm_tis_write_data(TPMState *s, hwaddr addr, uint64_t val, uint32_t size);
+uint16_t tpm_tis_get_checksum(TPMState *s);
#endif /* TPM_TPM_TIS_H */
diff --git a/hw/tpm/tpm_tis_common.c b/hw/tpm/tpm_tis_common.c
index 503be2a541..c6d139943e 100644
--- a/hw/tpm/tpm_tis_common.c
+++ b/hw/tpm/tpm_tis_common.c
@@ -26,6 +26,8 @@
#include "hw/irq.h"
#include "hw/isa/isa.h"
#include "qapi/error.h"
+#include "qemu/bswap.h"
+#include "qemu/crc-ccitt.h"
#include "qemu/module.h"
#include "hw/acpi/tpm.h"
@@ -447,6 +449,23 @@ static uint64_t tpm_tis_mmio_read(void *opaque, hwaddr addr,
return val;
}
+/*
+ * A wrapper read function so that it can be directly called without
+ * mmio.
+ */
+uint32_t tpm_tis_read_data(TPMState *s, hwaddr addr, unsigned size)
+{
+ return tpm_tis_mmio_read(s, addr, size);
+}
+
+/*
+ * Calculate current data buffer checksum
+ */
+uint16_t tpm_tis_get_checksum(TPMState *s)
+{
+ return bswap16(crc_ccitt(0, s->buffer, s->rw_offset));
+}
+
/*
* Write a value to a register of the TIS interface
* See specs pages 33-63 for description of the registers
@@ -767,6 +786,15 @@ static void tpm_tis_mmio_write(void *opaque, hwaddr addr,
}
}
+/*
+ * A wrapper write function so that it can be directly called without
+ * mmio.
+ */
+void tpm_tis_write_data(TPMState *s, hwaddr addr, uint64_t val, uint32_t size)
+{
+ tpm_tis_mmio_write(s, addr, val, size);
+}
+
const MemoryRegionOps tpm_tis_memory_ops = {
.read = tpm_tis_mmio_read,
.write = tpm_tis_mmio_write,
diff --git a/include/hw/acpi/tpm.h b/include/hw/acpi/tpm.h
index 559ba6906c..4f2424e2fe 100644
--- a/include/hw/acpi/tpm.h
+++ b/include/hw/acpi/tpm.h
@@ -93,6 +93,7 @@
#define TPM_TIS_CAP_DATA_TRANSFER_64B (3 << 9)
#define TPM_TIS_CAP_DATA_TRANSFER_LEGACY (0 << 9)
#define TPM_TIS_CAP_BURST_COUNT_DYNAMIC (0 << 8)
+#define TPM_TIS_CAP_BURST_COUNT_STATIC (1 << 8)
#define TPM_TIS_CAP_INTERRUPT_LOW_LEVEL (1 << 4) /* support is mandatory */
#define TPM_TIS_CAPABILITIES_SUPPORTED1_3 \
(TPM_TIS_CAP_INTERRUPT_LOW_LEVEL | \
@@ -209,6 +210,33 @@ REG32(CRB_DATA_BUFFER, 0x80)
#define TPM_PPI_FUNC_ALLOWED_USR_NOT_REQ (4 << 0)
#define TPM_PPI_FUNC_MASK (7 << 0)
+/* TPM TIS I2C registers */
+#define TPM_I2C_REG_LOC_SEL 0x00
+#define TPM_I2C_REG_ACCESS 0x04
+#define TPM_I2C_REG_INT_ENABLE 0x08
+#define TPM_I2C_REG_INT_CAPABILITY 0x14
+#define TPM_I2C_REG_STS 0x18
+#define TPM_I2C_REG_DATA_FIFO 0x24
+#define TPM_I2C_REG_INTF_CAPABILITY 0x30
+#define TPM_I2C_REG_I2C_DEV_ADDRESS 0x38
+#define TPM_I2C_REG_DATA_CSUM_ENABLE 0x40
+#define TPM_I2C_REG_DATA_CSUM_GET 0x44
+#define TPM_I2C_REG_DID_VID 0x48
+#define TPM_I2C_REG_RID 0x4c
+#define TPM_I2C_REG_UNKNOWN 0xff
+
+/* I2C specific interface capabilities */
+#define TPM_I2C_CAP_INTERFACE_TYPE (0x2 << 0) /* FIFO interface */
+#define TPM_I2C_CAP_INTERFACE_VER (0x0 << 4) /* TCG I2C intf 1.0 */
+#define TPM_I2C_CAP_TPM2_FAMILY (0x1 << 7) /* TPM 2.0 family. */
+#define TPM_I2C_CAP_DEV_ADDR_CHANGE (0x0 << 27) /* No dev addr chng */
+#define TPM_I2C_CAP_BURST_COUNT_STATIC (0x1 << 29) /* Burst count static */
+#define TPM_I2C_CAP_LOCALITY_CAP (0x1 << 25) /* 0-5 locality */
+#define TPM_I2C_CAP_BUS_SPEED (3 << 21) /* std and fast mode */
+
+/* TPM_STS mask for read bits 31:26 must be zero */
+#define TPM_I2C_STS_READ_MASK 0x03ffffff
+
void tpm_build_ppi_acpi(TPMIf *tpm, Aml *dev);
#endif /* CONFIG_TPM */
--
2.37.2
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v6 3/3] tpm: Add support for TPM device over I2C bus
2023-03-26 2:38 [PATCH v6 0/3] Add support for TPM devices over I2C bus Ninad Palsule
2023-03-26 2:38 ` [PATCH v6 1/3] docs: " Ninad Palsule
2023-03-26 2:38 ` [PATCH v6 2/3] tpm: Extend common APIs to support TPM TIS I2C Ninad Palsule
@ 2023-03-26 2:38 ` Ninad Palsule
2023-03-26 13:00 ` Stefan Berger
2 siblings, 1 reply; 6+ messages in thread
From: Ninad Palsule @ 2023-03-26 2:38 UTC (permalink / raw)
To: qemu-devel; +Cc: Ninad Palsule, joel, andrew, stefanb, clg
Qemu already supports devices attached to ISA and sysbus. This drop adds
support for the I2C bus attached TPM devices. I2C model only supports
TPM2 protocol.
This commit includes changes for the common code.
- Added I2C emulation model. Logic was added in the model to temporarily
cache the data as I2C interface works per byte basis.
- New tpm type "tpm-tis-i2c" added for I2C support. The user has to
provide this string on command line.
Testing:
TPM I2C device module is tested using SWTPM (software based TPM
package). Qemu uses the rainier machine and is connected to swtpm over
the socket interface.
The command to start swtpm is as follows:
$ swtpm socket --tpmstate dir=/tmp/mytpm1 \
--ctrl type=unixio,path=/tmp/mytpm1/swtpm-sock \
--tpm2 --log level=100
The command to start qemu is as follows:
$ qemu-system-arm -M rainier-bmc -nographic \
-kernel ${IMAGEPATH}/fitImage-linux.bin \
-dtb ${IMAGEPATH}/aspeed-bmc-ibm-rainier.dtb \
-initrd ${IMAGEPATH}/obmc-phosphor-initramfs.rootfs.cpio.xz \
-drive file=${IMAGEPATH}/obmc-phosphor-image.rootfs.wic.qcow2,if=sd,index=2 \
-net nic -net user,hostfwd=:127.0.0.1:2222-:22,hostfwd=:127.0.0.1:2443-:443 \
-chardev socket,id=chrtpm,path=/tmp/mytpm1/swtpm-sock \
-tpmdev emulator,id=tpm0,chardev=chrtpm \
-device tpm-tis-i2c,tpmdev=tpm0,bus=aspeed.i2c.bus.12,address=0x2e
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
---
V2:
Incorporated Stephen's review comments.
- Handled checksum related register in I2C layer
- Defined I2C interface capabilities and return those instead of
capabilities from TPM TIS. Add required capabilities from TIS.
- Do not cache FIFO data in the I2C layer.
- Make sure that Device address change register is not passed to I2C
layer as capability indicate that it is not supported.
- Added boundary checks.
- Make sure that bits 26-31 are zeroed for the TPM_STS register on read
- Updated Kconfig files for new define.
---
V3:
- Moved processing of register TPM_I2C_LOC_SEL in the I2C. So I2C layer
remembers the locality and pass it to TIS on each read/write.
- The write data is no more cached in the I2C layer so the buffer size
is reduced to 16 bytes.
- Checksum registers are now managed by the I2C layer. Added new
function in TIS layer to return the checksum and used that to process
the request.
- Now 2-4 byte register value will be passed to TIS layer in a single
write call instead of 1 byte at a time. Added functions to convert
between little endian stream of bytes to single 32 bit unsigned
integer. Similarly 32 bit integer to stream of bytes.
- Added restriction on device change register.
- Replace few if-else statement with switch statement for clarity.
- Log warning when unknown register is received.
- Moved all register definations to acpi/tmp.h
---
V4:
Incorporated review comments from Cedric and Stefan.
- Reduced data[] size from 16 byte to 5 bytes.
- Added register name in the mapping table which can be used for
tracing.
- Removed the endian conversion functions instead used simple logic
provided by Stefan.
- Rename I2C registers to reduce the length.
- Added traces for send, recv and event functions. You can turn on trace
on command line by using "-trace "tpm_tis_i2c*" option.
---
V5:
Fixed issues reported by Stefan's test.
- Added mask for the INT_ENABLE register.
- Use correct TIS register for reading interrupt capability.
- Cleanup how register is converted from I2C to TIS and also saved
information like tis_addr and register name in the i2cst so that we
can only convert it once on i2c_send.
- Trace register number for unknown registers.
---
V6:
Fixed review comments from Stefan.
- Fixed some variable size.
- Removed unused variables.
- Added vmstat backin to handle migration.
- Added post load phase to reload tis address and register name.
---
hw/arm/Kconfig | 1 +
hw/tpm/Kconfig | 7 +
hw/tpm/meson.build | 1 +
hw/tpm/tpm_tis_i2c.c | 533 +++++++++++++++++++++++++++++++++++++++++++
hw/tpm/trace-events | 6 +
include/sysemu/tpm.h | 3 +
6 files changed, 551 insertions(+)
create mode 100644 hw/tpm/tpm_tis_i2c.c
diff --git a/hw/arm/Kconfig b/hw/arm/Kconfig
index b5aed4aff5..05d6ef1a31 100644
--- a/hw/arm/Kconfig
+++ b/hw/arm/Kconfig
@@ -6,6 +6,7 @@ config ARM_VIRT
imply VFIO_PLATFORM
imply VFIO_XGMAC
imply TPM_TIS_SYSBUS
+ imply TPM_TIS_I2C
imply NVDIMM
select ARM_GIC
select ACPI
diff --git a/hw/tpm/Kconfig b/hw/tpm/Kconfig
index 29e82f3c92..a46663288c 100644
--- a/hw/tpm/Kconfig
+++ b/hw/tpm/Kconfig
@@ -1,3 +1,10 @@
+config TPM_TIS_I2C
+ bool
+ depends on TPM
+ select TPM_BACKEND
+ select I2C
+ select TPM_TIS
+
config TPM_TIS_ISA
bool
depends on TPM && ISA_BUS
diff --git a/hw/tpm/meson.build b/hw/tpm/meson.build
index 7abc2d794a..76fe3cb098 100644
--- a/hw/tpm/meson.build
+++ b/hw/tpm/meson.build
@@ -1,6 +1,7 @@
softmmu_ss.add(when: 'CONFIG_TPM_TIS', if_true: files('tpm_tis_common.c'))
softmmu_ss.add(when: 'CONFIG_TPM_TIS_ISA', if_true: files('tpm_tis_isa.c'))
softmmu_ss.add(when: 'CONFIG_TPM_TIS_SYSBUS', if_true: files('tpm_tis_sysbus.c'))
+softmmu_ss.add(when: 'CONFIG_TPM_TIS_I2C', if_true: files('tpm_tis_i2c.c'))
softmmu_ss.add(when: 'CONFIG_TPM_CRB', if_true: files('tpm_crb.c'))
softmmu_ss.add(when: 'CONFIG_TPM_TIS', if_true: files('tpm_ppi.c'))
softmmu_ss.add(when: 'CONFIG_TPM_CRB', if_true: files('tpm_ppi.c'))
diff --git a/hw/tpm/tpm_tis_i2c.c b/hw/tpm/tpm_tis_i2c.c
new file mode 100644
index 0000000000..1e60dadb72
--- /dev/null
+++ b/hw/tpm/tpm_tis_i2c.c
@@ -0,0 +1,533 @@
+/*
+ * tpm_tis_i2c.c - QEMU's TPM TIS I2C Device
+ *
+ * This work is licensed under the terms of the GNU GPL, version 2 or later.
+ * See the COPYING file in the top-level directory.
+ *
+ * Implementation of the TIS interface according to specs found at
+ * http://www.trustedcomputinggroup.org. This implementation currently
+ * supports version 1.3, 21 March 2013
+ * In the developers menu choose the PC Client section then find the TIS
+ * specification.
+ *
+ * TPM TIS for TPM 2 implementation following TCG PC Client Platform
+ * TPM Profile (PTP) Specification, Familiy 2.0, Revision 00.43
+ *
+ * TPM I2C implementation follows TCG TPM I2c Interface specification,
+ * Family 2.0, Level 00, Revision 1.00
+ */
+
+#include "qemu/osdep.h"
+#include "hw/i2c/i2c.h"
+#include "hw/qdev-properties.h"
+#include "hw/acpi/tpm.h"
+#include "migration/vmstate.h"
+#include "tpm_prop.h"
+#include "qom/object.h"
+#include "block/aio.h"
+#include "qemu/main-loop.h"
+#include "qemu/log.h"
+#include "trace.h"
+#include "tpm_tis.h"
+
+/* TPM_STS mask for read bits 31:26 must be zero */
+#define TPM_I2C_STS_READ_MASK 0x03ffffff
+
+/* Checksum enabled. */
+#define TPM_DATA_CSUM_ENABLED 0x1
+
+/* TPM_I2C_INT_ENABLE mask */
+#define TPM_I2C_INT_ENABLE_MASK (TPM_TIS_INT_ENABLED | \
+ TPM_TIS_INT_DATA_AVAILABLE | \
+ TPM_TIS_INT_STS_VALID | \
+ TPM_TIS_INT_LOCALITY_CHANGED | \
+ TPM_TIS_INT_COMMAND_READY)
+
+/* Operations */
+#define OP_SEND 1
+#define OP_RECV 2
+
+typedef struct TPMStateI2C {
+ /*< private >*/
+ I2CSlave parent_obj;
+
+ uint8_t offset; /* offset into data[] */
+ uint8_t operation; /* OP_SEND & OP_RECV */
+ uint8_t data[5]; /* Data */
+
+ /* i2c registers */
+ uint8_t loc_sel; /* Current locality */
+ uint8_t csum_enable; /* Is checksum enabled */
+
+ /* Derived from the above */
+ const char *reg_name; /* Register name */
+ uint32_t tis_addr; /* Converted tis address including locty */
+
+ /*< public >*/
+ TPMState state; /* not a QOM object */
+
+} TPMStateI2C;
+
+DECLARE_INSTANCE_CHECKER(TPMStateI2C, TPM_TIS_I2C,
+ TYPE_TPM_TIS_I2C)
+
+/* Prototype */
+static inline void tpm_tis_i2c_to_tis_reg(TPMStateI2C *i2cst, uint8_t i2c_reg);
+
+/* Register map */
+typedef struct regMap {
+ uint8_t i2c_reg; /* I2C register */
+ uint16_t tis_reg; /* TIS register */
+ char name[16]; /* Register name */
+} I2CRegMap;
+
+/*
+ * The register values in the common code is different than the latest
+ * register numbers as per the spec hence add the conversion map
+ */
+static const I2CRegMap tpm_tis_reg_map[] = {
+ /*
+ * These registers are sent to TIS layer. The register with UNKNOWN
+ * mapping are not sent to TIS layer and handled in I2c layer.
+ * NOTE: Adding frequently used registers at the start
+ */
+ { TPM_I2C_REG_DATA_FIFO, TPM_TIS_REG_DATA_FIFO, "FIFO", },
+ { TPM_I2C_REG_STS, TPM_TIS_REG_STS, "STS", },
+ { TPM_I2C_REG_DATA_CSUM_GET, TPM_I2C_REG_UNKNOWN, "CSUM_GET", },
+ { TPM_I2C_REG_LOC_SEL, TPM_I2C_REG_UNKNOWN, "LOC_SEL", },
+ { TPM_I2C_REG_ACCESS, TPM_TIS_REG_ACCESS, "ACCESS", },
+ { TPM_I2C_REG_INT_ENABLE, TPM_TIS_REG_INT_ENABLE, "INTR_ENABLE",},
+ { TPM_I2C_REG_INT_CAPABILITY, TPM_TIS_REG_INT_ENABLE, "INTR_CAP", },
+ { TPM_I2C_REG_INTF_CAPABILITY, TPM_TIS_REG_INTF_CAPABILITY, "INTF_CAP", },
+ { TPM_I2C_REG_DID_VID, TPM_TIS_REG_DID_VID, "DID_VID", },
+ { TPM_I2C_REG_RID, TPM_TIS_REG_RID, "RID", },
+ { TPM_I2C_REG_I2C_DEV_ADDRESS, TPM_I2C_REG_UNKNOWN, "DEV_ADDRESS",},
+ { TPM_I2C_REG_DATA_CSUM_ENABLE, TPM_I2C_REG_UNKNOWN, "CSUM_ENABLE",},
+};
+
+static int tpm_tis_i2c_pre_save(void *opaque)
+{
+ TPMStateI2C *i2cst = opaque;
+
+ return tpm_tis_pre_save(&i2cst->state);
+}
+
+static int tpm_tis_i2c_post_load(void *opaque, int version_id)
+{
+ TPMStateI2C *i2cst = opaque;
+
+ if (i2cst->offset >= 1) {
+ tpm_tis_i2c_to_tis_reg(i2cst, i2cst->data[0]);
+ }
+
+ return 0;
+}
+
+static const VMStateDescription vmstate_tpm_tis_i2c = {
+ .name = "tpm-tis-i2c",
+ .version_id = 0,
+ .pre_save = tpm_tis_i2c_pre_save,
+ .post_load = tpm_tis_i2c_post_load,
+ .fields = (VMStateField[]) {
+ VMSTATE_BUFFER(state.buffer, TPMStateI2C),
+ VMSTATE_UINT16(state.rw_offset, TPMStateI2C),
+ VMSTATE_UINT8(state.active_locty, TPMStateI2C),
+ VMSTATE_UINT8(state.aborting_locty, TPMStateI2C),
+ VMSTATE_UINT8(state.next_locty, TPMStateI2C),
+
+ VMSTATE_STRUCT_ARRAY(state.loc, TPMStateI2C, TPM_TIS_NUM_LOCALITIES, 0,
+ vmstate_locty, TPMLocality),
+
+ /* i2c specifics */
+ VMSTATE_UINT8(offset, TPMStateI2C),
+ VMSTATE_UINT8(operation, TPMStateI2C),
+ VMSTATE_BUFFER(data, TPMStateI2C),
+ VMSTATE_UINT8(loc_sel, TPMStateI2C),
+ VMSTATE_UINT8(csum_enable, TPMStateI2C),
+
+ VMSTATE_END_OF_LIST()
+ }
+};
+
+/*
+ * Generate interface capability based on what is returned by TIS and what is
+ * expected by I2C. Save the capability in the data array overwriting the TIS
+ * capability.
+ */
+static uint32_t tpm_i2c_interface_capability(TPMStateI2C *i2cst,
+ uint32_t tis_cap)
+{
+ uint32_t i2c_cap = 0;
+
+ /* Now generate i2c capability */
+ i2c_cap = (TPM_I2C_CAP_INTERFACE_TYPE |
+ TPM_I2C_CAP_INTERFACE_VER |
+ TPM_I2C_CAP_TPM2_FAMILY |
+ TPM_I2C_CAP_LOCALITY_CAP |
+ TPM_I2C_CAP_BUS_SPEED |
+ TPM_I2C_CAP_DEV_ADDR_CHANGE);
+
+ /* Now check the TIS and set some capabilities */
+
+ /* Static burst count set */
+ if (tis_cap & TPM_TIS_CAP_BURST_COUNT_STATIC) {
+ i2c_cap |= TPM_I2C_CAP_BURST_COUNT_STATIC;
+ }
+
+ return i2c_cap;
+}
+
+/* Convert I2C register to TIS address and returns the name of the register */
+static inline void tpm_tis_i2c_to_tis_reg(TPMStateI2C *i2cst, uint8_t i2c_reg)
+{
+ const I2CRegMap *reg_map;
+ int i;
+
+ i2cst->tis_addr = 0xffffffff;
+
+ for (i = 0; i < ARRAY_SIZE(tpm_tis_reg_map); i++) {
+ reg_map = &tpm_tis_reg_map[i];
+ if (reg_map->i2c_reg == i2c_reg) {
+ i2cst->reg_name = reg_map->name;
+ i2cst->tis_addr = reg_map->tis_reg;
+ if (i2cst->loc_sel != TPM_TIS_NO_LOCALITY) {
+ /* Include the locality in the address. */
+ i2cst->tis_addr += (i2cst->loc_sel << TPM_TIS_LOCALITY_SHIFT);
+ }
+ break;
+ }
+ }
+
+ if (i2cst->tis_addr == 0xffffffff) {
+ qemu_log_mask(LOG_UNIMP, "%s: Could not convert i2c register: 0x%X\n",
+ __func__, i2cst->data[0]);
+ }
+}
+
+/* Clear some fields from the structure. */
+static inline void tpm_tis_i2c_clear_data(TPMStateI2C *i2cst)
+{
+ /* Clear operation and offset */
+ i2cst->operation = 0;
+ i2cst->offset = 0;
+ i2cst->tis_addr = 0xffffffff;
+ i2cst->reg_name = NULL;
+ memset(i2cst->data, 0, sizeof(i2cst->data));
+
+ return;
+}
+
+/* Send data to TPM */
+static inline void tpm_tis_i2c_tpm_send(TPMStateI2C *i2cst)
+{
+ uint32_t data;
+
+ if ((i2cst->operation == OP_SEND) && (i2cst->offset > 1)) {
+
+ switch (i2cst->data[0]) {
+ case TPM_I2C_REG_DATA_CSUM_ENABLE:
+ /*
+ * Checksum is not handled by TIS code hence we will consume the
+ * register here.
+ */
+ i2cst->csum_enable = TPM_DATA_CSUM_ENABLED;
+ break;
+ case TPM_I2C_REG_DATA_FIFO:
+ /* Handled in the main i2c_send function */
+ break;
+ case TPM_I2C_REG_LOC_SEL:
+ /*
+ * This register is not handled by TIS so save the locality
+ * locally
+ */
+ i2cst->loc_sel = i2cst->data[1];
+ break;
+ default:
+ /* We handle non-FIFO here */
+
+ /* Index 0 is a register. Convert byte stream to uint32_t */
+ data = i2cst->data[1];
+ data |= i2cst->data[2] << 8;
+ data |= i2cst->data[3] << 16;
+ data |= i2cst->data[4] << 24;
+
+ /* Add register specific masking */
+ switch (i2cst->data[0]) {
+ case TPM_I2C_REG_INT_ENABLE:
+ data &= TPM_I2C_INT_ENABLE_MASK;
+ break;
+ }
+
+ tpm_tis_write_data(&i2cst->state, i2cst->tis_addr, data, 4);
+ break;
+ }
+
+ tpm_tis_i2c_clear_data(i2cst);
+ }
+
+ return;
+}
+
+/* Callback from TPM to indicate that response is copied */
+static void tpm_tis_i2c_request_completed(TPMIf *ti, int ret)
+{
+ TPMStateI2C *i2cst = TPM_TIS_I2C(ti);
+ TPMState *s = &i2cst->state;
+
+ /* Inform the common code. */
+ tpm_tis_request_completed(s, ret);
+}
+
+static enum TPMVersion tpm_tis_i2c_get_tpm_version(TPMIf *ti)
+{
+ TPMStateI2C *i2cst = TPM_TIS_I2C(ti);
+ TPMState *s = &i2cst->state;
+
+ return tpm_tis_get_tpm_version(s);
+}
+
+static int tpm_tis_i2c_event(I2CSlave *i2c, enum i2c_event event)
+{
+ TPMStateI2C *i2cst = TPM_TIS_I2C(i2c);
+ int ret = 0;
+
+ switch (event) {
+ case I2C_START_RECV:
+ trace_tpm_tis_i2c_event("START_RECV");
+ break;
+ case I2C_START_SEND:
+ trace_tpm_tis_i2c_event("START_SEND");
+ tpm_tis_i2c_clear_data(i2cst);
+ break;
+ case I2C_FINISH:
+ trace_tpm_tis_i2c_event("FINISH");
+ if (i2cst->operation == OP_SEND) {
+ tpm_tis_i2c_tpm_send(i2cst);
+ } else {
+ tpm_tis_i2c_clear_data(i2cst);
+ }
+ break;
+ default:
+ break;
+ }
+
+ return ret;
+}
+
+/*
+ * If data is for FIFO then it is received from tpm_tis_common buffer
+ * otherwise it will be handled using single call to common code and
+ * cached in the local buffer.
+ */
+static uint8_t tpm_tis_i2c_recv(I2CSlave *i2c)
+{
+ int ret = 0;
+ uint32_t data_read;
+ TPMStateI2C *i2cst = TPM_TIS_I2C(i2c);
+ TPMState *s = &i2cst->state;
+ uint16_t i2c_reg = i2cst->data[0];
+
+ if (i2cst->operation == OP_RECV) {
+
+ /* Do not cache FIFO data. */
+ if (i2cst->data[0] == TPM_I2C_REG_DATA_FIFO) {
+ data_read = tpm_tis_read_data(s, i2cst->tis_addr, 1);
+ ret = (data_read & 0xff);
+ } else if (sizeof(i2cst->data)) {
+ ret = i2cst->data[i2cst->offset++];
+ }
+
+ } else if ((i2cst->operation == OP_SEND) && (i2cst->offset < 2)) {
+ /* First receive call after send */
+
+ i2cst->operation = OP_RECV;
+
+ switch (i2c_reg) {
+ case TPM_I2C_REG_LOC_SEL:
+ /* Location selection register is managed by i2c */
+ i2cst->data[1] = i2cst->loc_sel;
+ break;
+ case TPM_I2C_REG_DATA_FIFO:
+ /* FIFO data is directly read from TPM TIS */
+ data_read = tpm_tis_read_data(s, i2cst->tis_addr, 1);
+ i2cst->data[1] = (data_read & 0xff);
+ break;
+ case TPM_I2C_REG_DATA_CSUM_ENABLE:
+ i2cst->data[1] = i2cst->csum_enable;
+ break;
+ case TPM_I2C_REG_DATA_CSUM_GET:
+ /*
+ * Checksum registers are not supported by common code hence
+ * call a common code to get the checksum.
+ */
+ data_read = tpm_tis_get_checksum(s);
+
+ /* Save the byte stream in data field */
+ i2cst->data[1] = (data_read & 0xff);
+ i2cst->data[2] = ((data_read >> 8) & 0xff);
+ break;
+ default:
+ data_read = tpm_tis_read_data(s, i2cst->tis_addr, 4);
+
+ if (i2c_reg == TPM_I2C_REG_INTF_CAPABILITY) {
+ /* Prepare the capabilities as per I2C interface */
+ data_read = tpm_i2c_interface_capability(i2cst,
+ data_read);
+ } else if (i2c_reg == TPM_I2C_REG_STS) {
+ /*
+ * As per specs, STS bit 31:26 are reserved and must
+ * be set to 0
+ */
+ data_read &= TPM_I2C_STS_READ_MASK;
+ }
+ /* Save byte stream in data[] */
+ i2cst->data[1] = data_read;
+ i2cst->data[2] = data_read >> 8;
+ i2cst->data[3] = data_read >> 16;
+ i2cst->data[4] = data_read >> 24;
+ break;
+ }
+
+
+ /* Return first byte with this call */
+ i2cst->offset = 1; /* keep the register value intact for debug */
+ ret = i2cst->data[i2cst->offset++];
+ } else {
+ i2cst->operation = OP_RECV;
+ }
+
+ trace_tpm_tis_i2c_recv(ret);
+
+ return ret;
+}
+
+/*
+ * Send function only remembers data in the buffer and then calls
+ * TPM TIS common code during FINISH event.
+ */
+static int tpm_tis_i2c_send(I2CSlave *i2c, uint8_t data)
+{
+ TPMStateI2C *i2cst = TPM_TIS_I2C(i2c);
+
+ /* Reject non-supported registers. */
+ if (i2cst->offset == 0) {
+ /* Convert I2C register to TIS register */
+ tpm_tis_i2c_to_tis_reg(i2cst, data);
+ if (i2cst->tis_addr == 0xffffffff) {
+ return 0xffffffff;
+ }
+
+ trace_tpm_tis_i2c_send_reg(i2cst->reg_name, data);
+
+ /* We do not support device address change */
+ if (data == TPM_I2C_REG_I2C_DEV_ADDRESS) {
+ qemu_log_mask(LOG_UNIMP, "%s: Device address change "
+ "is not supported.\n", __func__);
+ return 0xffffffff;
+ }
+ } else {
+ trace_tpm_tis_i2c_send(data);
+ }
+
+ if (i2cst->offset < sizeof(i2cst->data)) {
+ i2cst->operation = OP_SEND;
+
+ /* Remember data locally for non-FIFO registers */
+ if ((i2cst->offset == 0) ||
+ (i2cst->data[0] != TPM_I2C_REG_DATA_FIFO)) {
+ i2cst->data[i2cst->offset++] = data;
+ } else {
+ tpm_tis_write_data(&i2cst->state, i2cst->tis_addr, data, 1);
+ }
+
+ return 0;
+
+ } else {
+ /* Return non-zero to indicate NAK */
+ return 1;
+ }
+}
+
+static Property tpm_tis_i2c_properties[] = {
+ DEFINE_PROP_UINT32("irq", TPMStateI2C, state.irq_num, TPM_TIS_IRQ),
+ DEFINE_PROP_TPMBE("tpmdev", TPMStateI2C, state.be_driver),
+ DEFINE_PROP_END_OF_LIST(),
+};
+
+static void tpm_tis_i2c_realizefn(DeviceState *dev, Error **errp)
+{
+ TPMStateI2C *i2cst = TPM_TIS_I2C(dev);
+ TPMState *s = &i2cst->state;
+
+ if (!tpm_find()) {
+ error_setg(errp, "at most one TPM device is permitted");
+ return;
+ }
+
+ /*
+ * Get the backend pointer. It is not initialized propery during
+ * device_class_set_props
+ */
+ s->be_driver = qemu_find_tpm_be("tpm0");
+
+ if (!s->be_driver) {
+ error_setg(errp, "'tpmdev' property is required");
+ return;
+ }
+ if (s->irq_num > 15) {
+ error_setg(errp, "IRQ %d is outside valid range of 0 to 15",
+ s->irq_num);
+ return;
+ }
+}
+
+static void tpm_tis_i2c_reset(DeviceState *dev)
+{
+ TPMStateI2C *i2cst = TPM_TIS_I2C(dev);
+ TPMState *s = &i2cst->state;
+
+ tpm_tis_i2c_clear_data(i2cst);
+
+ i2cst->csum_enable = 0;
+ i2cst->loc_sel = TPM_TIS_NO_LOCALITY;
+
+ return tpm_tis_reset(s);
+}
+
+static void tpm_tis_i2c_class_init(ObjectClass *klass, void *data)
+{
+ DeviceClass *dc = DEVICE_CLASS(klass);
+ I2CSlaveClass *k = I2C_SLAVE_CLASS(klass);
+ TPMIfClass *tc = TPM_IF_CLASS(klass);
+
+ dc->realize = tpm_tis_i2c_realizefn;
+ dc->reset = tpm_tis_i2c_reset;
+ dc->vmsd = &vmstate_tpm_tis_i2c;
+ device_class_set_props(dc, tpm_tis_i2c_properties);
+
+ k->event = tpm_tis_i2c_event;
+ k->recv = tpm_tis_i2c_recv;
+ k->send = tpm_tis_i2c_send;
+
+ tc->model = TPM_MODEL_TPM_TIS;
+ tc->request_completed = tpm_tis_i2c_request_completed;
+ tc->get_version = tpm_tis_i2c_get_tpm_version;
+}
+
+static const TypeInfo tpm_tis_i2c_info = {
+ .name = TYPE_TPM_TIS_I2C,
+ .parent = TYPE_I2C_SLAVE,
+ .instance_size = sizeof(TPMStateI2C),
+ .class_init = tpm_tis_i2c_class_init,
+ .interfaces = (InterfaceInfo[]) {
+ { TYPE_TPM_IF },
+ { }
+ }
+};
+
+static void tpm_tis_i2c_register_types(void)
+{
+ type_register_static(&tpm_tis_i2c_info);
+}
+
+type_init(tpm_tis_i2c_register_types)
diff --git a/hw/tpm/trace-events b/hw/tpm/trace-events
index f17110458e..fa882dfefe 100644
--- a/hw/tpm/trace-events
+++ b/hw/tpm/trace-events
@@ -36,3 +36,9 @@ tpm_spapr_do_crq_unknown_msg_type(uint8_t type) "Unknown message type 0x%02x"
tpm_spapr_do_crq_unknown_crq(uint8_t raw1, uint8_t raw2) "unknown CRQ 0x%02x 0x%02x ..."
tpm_spapr_post_load(void) "Delivering TPM response after resume"
tpm_spapr_caught_response(uint32_t v) "Caught response to deliver after resume: %u bytes"
+
+# tpm_tis_i2c.c
+tpm_tis_i2c_recv(uint8_t data) "TPM I2C read: 0x%X"
+tpm_tis_i2c_send(uint8_t data) "TPM I2C write: 0x%X"
+tpm_tis_i2c_event(const char *event) "TPM I2C event: %s"
+tpm_tis_i2c_send_reg(const char *name, int reg) "TPM I2C write register: %s(0x%X)"
diff --git a/include/sysemu/tpm.h b/include/sysemu/tpm.h
index fb40e30ff6..66e3b45f30 100644
--- a/include/sysemu/tpm.h
+++ b/include/sysemu/tpm.h
@@ -48,6 +48,7 @@ struct TPMIfClass {
#define TYPE_TPM_TIS_SYSBUS "tpm-tis-device"
#define TYPE_TPM_CRB "tpm-crb"
#define TYPE_TPM_SPAPR "tpm-spapr"
+#define TYPE_TPM_TIS_I2C "tpm-tis-i2c"
#define TPM_IS_TIS_ISA(chr) \
object_dynamic_cast(OBJECT(chr), TYPE_TPM_TIS_ISA)
@@ -57,6 +58,8 @@ struct TPMIfClass {
object_dynamic_cast(OBJECT(chr), TYPE_TPM_CRB)
#define TPM_IS_SPAPR(chr) \
object_dynamic_cast(OBJECT(chr), TYPE_TPM_SPAPR)
+#define TPM_IS_TIS_I2C(chr) \
+ object_dynamic_cast(OBJECT(chr), TYPE_TPM_TIS_I2C)
/* returns NULL unless there is exactly one TPM device */
static inline TPMIf *tpm_find(void)
--
2.37.2
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v6 3/3] tpm: Add support for TPM device over I2C bus
2023-03-26 2:38 ` [PATCH v6 3/3] tpm: Add support for TPM device over I2C bus Ninad Palsule
@ 2023-03-26 13:00 ` Stefan Berger
2023-03-26 22:23 ` Ninad Palsule
0 siblings, 1 reply; 6+ messages in thread
From: Stefan Berger @ 2023-03-26 13:00 UTC (permalink / raw)
To: Ninad Palsule, qemu-devel; +Cc: joel, andrew, clg
On 3/25/23 22:38, Ninad Palsule wrote:
> Qemu already supports devices attached to ISA and sysbus. This drop adds
> support for the I2C bus attached TPM devices. I2C model only supports
> TPM2 protocol.
>
> This commit includes changes for the common code.
> - Added I2C emulation model. Logic was added in the model to temporarily
> cache the data as I2C interface works per byte basis.
> - New tpm type "tpm-tis-i2c" added for I2C support. The user has to
> provide this string on command line.
>
> Testing:
> TPM I2C device module is tested using SWTPM (software based TPM
> package). Qemu uses the rainier machine and is connected to swtpm over
> the socket interface.
>
> The command to start swtpm is as follows:
> $ swtpm socket --tpmstate dir=/tmp/mytpm1 \
> --ctrl type=unixio,path=/tmp/mytpm1/swtpm-sock \
> --tpm2 --log level=100
>
> The command to start qemu is as follows:
> $ qemu-system-arm -M rainier-bmc -nographic \
> -kernel ${IMAGEPATH}/fitImage-linux.bin \
> -dtb ${IMAGEPATH}/aspeed-bmc-ibm-rainier.dtb \
> -initrd ${IMAGEPATH}/obmc-phosphor-initramfs.rootfs.cpio.xz \
> -drive file=${IMAGEPATH}/obmc-phosphor-image.rootfs.wic.qcow2,if=sd,index=2 \
> -net nic -net user,hostfwd=:127.0.0.1:2222-:22,hostfwd=:127.0.0.1:2443-:443 \
> -chardev socket,id=chrtpm,path=/tmp/mytpm1/swtpm-sock \
> -tpmdev emulator,id=tpm0,chardev=chrtpm \
> -device tpm-tis-i2c,tpmdev=tpm0,bus=aspeed.i2c.bus.12,address=0x2e
>
> Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
> ---
> V2:
> Incorporated Stephen's review comments.
> - Handled checksum related register in I2C layer
> - Defined I2C interface capabilities and return those instead of
> capabilities from TPM TIS. Add required capabilities from TIS.
> - Do not cache FIFO data in the I2C layer.
> - Make sure that Device address change register is not passed to I2C
> layer as capability indicate that it is not supported.
> - Added boundary checks.
> - Make sure that bits 26-31 are zeroed for the TPM_STS register on read
> - Updated Kconfig files for new define.
>
> ---
> V3:
> - Moved processing of register TPM_I2C_LOC_SEL in the I2C. So I2C layer
> remembers the locality and pass it to TIS on each read/write.
> - The write data is no more cached in the I2C layer so the buffer size
> is reduced to 16 bytes.
> - Checksum registers are now managed by the I2C layer. Added new
> function in TIS layer to return the checksum and used that to process
> the request.
> - Now 2-4 byte register value will be passed to TIS layer in a single
> write call instead of 1 byte at a time. Added functions to convert
> between little endian stream of bytes to single 32 bit unsigned
> integer. Similarly 32 bit integer to stream of bytes.
> - Added restriction on device change register.
> - Replace few if-else statement with switch statement for clarity.
> - Log warning when unknown register is received.
> - Moved all register definations to acpi/tmp.h
>
> ---
> V4:
> Incorporated review comments from Cedric and Stefan.
> - Reduced data[] size from 16 byte to 5 bytes.
> - Added register name in the mapping table which can be used for
> tracing.
> - Removed the endian conversion functions instead used simple logic
> provided by Stefan.
> - Rename I2C registers to reduce the length.
> - Added traces for send, recv and event functions. You can turn on trace
> on command line by using "-trace "tpm_tis_i2c*" option.
>
> ---
> V5:
> Fixed issues reported by Stefan's test.
> - Added mask for the INT_ENABLE register.
> - Use correct TIS register for reading interrupt capability.
> - Cleanup how register is converted from I2C to TIS and also saved
> information like tis_addr and register name in the i2cst so that we
> can only convert it once on i2c_send.
> - Trace register number for unknown registers.
>
> ---
> V6:
> Fixed review comments from Stefan.
> - Fixed some variable size.
> - Removed unused variables.
> - Added vmstat backin to handle migration.
> - Added post load phase to reload tis address and register name.
> ---
> hw/arm/Kconfig | 1 +
> hw/tpm/Kconfig | 7 +
> hw/tpm/meson.build | 1 +
> hw/tpm/tpm_tis_i2c.c | 533 +++++++++++++++++++++++++++++++++++++++++++
> hw/tpm/trace-events | 6 +
> include/sysemu/tpm.h | 3 +
> 6 files changed, 551 insertions(+)
> create mode 100644 hw/tpm/tpm_tis_i2c.c
>
> diff --git a/hw/arm/Kconfig b/hw/arm/Kconfig
> index b5aed4aff5..05d6ef1a31 100644
> --- a/hw/arm/Kconfig
> +++ b/hw/arm/Kconfig
> @@ -6,6 +6,7 @@ config ARM_VIRT
> imply VFIO_PLATFORM
> imply VFIO_XGMAC
> imply TPM_TIS_SYSBUS
> + imply TPM_TIS_I2C
> imply NVDIMM
> select ARM_GIC
> select ACPI
> diff --git a/hw/tpm/Kconfig b/hw/tpm/Kconfig
> index 29e82f3c92..a46663288c 100644
> --- a/hw/tpm/Kconfig
> +++ b/hw/tpm/Kconfig
> @@ -1,3 +1,10 @@
> +config TPM_TIS_I2C
> + bool
> + depends on TPM
> + select TPM_BACKEND
> + select I2C
> + select TPM_TIS
> +
> config TPM_TIS_ISA
> bool
> depends on TPM && ISA_BUS
> diff --git a/hw/tpm/meson.build b/hw/tpm/meson.build
> index 7abc2d794a..76fe3cb098 100644
> --- a/hw/tpm/meson.build
> +++ b/hw/tpm/meson.build
> @@ -1,6 +1,7 @@
> softmmu_ss.add(when: 'CONFIG_TPM_TIS', if_true: files('tpm_tis_common.c'))
> softmmu_ss.add(when: 'CONFIG_TPM_TIS_ISA', if_true: files('tpm_tis_isa.c'))
> softmmu_ss.add(when: 'CONFIG_TPM_TIS_SYSBUS', if_true: files('tpm_tis_sysbus.c'))
> +softmmu_ss.add(when: 'CONFIG_TPM_TIS_I2C', if_true: files('tpm_tis_i2c.c'))
> softmmu_ss.add(when: 'CONFIG_TPM_CRB', if_true: files('tpm_crb.c'))
> softmmu_ss.add(when: 'CONFIG_TPM_TIS', if_true: files('tpm_ppi.c'))
> softmmu_ss.add(when: 'CONFIG_TPM_CRB', if_true: files('tpm_ppi.c'))
> diff --git a/hw/tpm/tpm_tis_i2c.c b/hw/tpm/tpm_tis_i2c.c
> new file mode 100644
> index 0000000000..1e60dadb72
> --- /dev/null
> +++ b/hw/tpm/tpm_tis_i2c.c
> @@ -0,0 +1,533 @@
> +/*
> + * tpm_tis_i2c.c - QEMU's TPM TIS I2C Device
> + *
> + * This work is licensed under the terms of the GNU GPL, version 2 or later.
> + * See the COPYING file in the top-level directory.
> + *
> + * Implementation of the TIS interface according to specs found at
> + * http://www.trustedcomputinggroup.org. This implementation currently
> + * supports version 1.3, 21 March 2013
> + * In the developers menu choose the PC Client section then find the TIS
> + * specification.
> + *
> + * TPM TIS for TPM 2 implementation following TCG PC Client Platform
> + * TPM Profile (PTP) Specification, Familiy 2.0, Revision 00.43
> + *
> + * TPM I2C implementation follows TCG TPM I2c Interface specification,
> + * Family 2.0, Level 00, Revision 1.00
> + */
> +
> +#include "qemu/osdep.h"
> +#include "hw/i2c/i2c.h"
> +#include "hw/qdev-properties.h"
This one is not needed.
> +#include "hw/acpi/tpm.h"
> +#include "migration/vmstate.h"
> +#include "tpm_prop.h"
> +#include "qom/object.h"
> +#include "block/aio.h"
> +#include "qemu/main-loop.h"
The above 3 are not needed.
> +#include "qemu/log.h"
> +#include "trace.h"
> +#include "tpm_tis.h"
> +
> +/* TPM_STS mask for read bits 31:26 must be zero */
> +#define TPM_I2C_STS_READ_MASK 0x03ffffff
> +
> +/* Checksum enabled. */
> +#define TPM_DATA_CSUM_ENABLED 0x1
Can you move this to the public header file? I'd use it in the test cases as well.
> +
> +/* TPM_I2C_INT_ENABLE mask */
> +#define TPM_I2C_INT_ENABLE_MASK (TPM_TIS_INT_ENABLED | \
> + TPM_TIS_INT_DATA_AVAILABLE | \
> + TPM_TIS_INT_STS_VALID | \
> + TPM_TIS_INT_LOCALITY_CHANGED | \
> + TPM_TIS_INT_COMMAND_READY)
> +
> +/* Operations */
> +#define OP_SEND 1
> +#define OP_RECV 2
> +
> +typedef struct TPMStateI2C {
> + /*< private >*/
> + I2CSlave parent_obj;
> +
> + uint8_t offset; /* offset into data[] */
> + uint8_t operation; /* OP_SEND & OP_RECV */
> + uint8_t data[5]; /* Data */
> +
> + /* i2c registers */
> + uint8_t loc_sel; /* Current locality */
> + uint8_t csum_enable; /* Is checksum enabled */
> +
> + /* Derived from the above */
> + const char *reg_name; /* Register name */
> + uint32_t tis_addr; /* Converted tis address including locty */
> +
> + /*< public >*/
> + TPMState state; /* not a QOM object */
> +
> +} TPMStateI2C;
> +
> +DECLARE_INSTANCE_CHECKER(TPMStateI2C, TPM_TIS_I2C,
> + TYPE_TPM_TIS_I2C)
> +
> +/* Prototype */
> +static inline void tpm_tis_i2c_to_tis_reg(TPMStateI2C *i2cst, uint8_t i2c_reg);
> +
> +/* Register map */
> +typedef struct regMap {
> + uint8_t i2c_reg; /* I2C register */
> + uint16_t tis_reg; /* TIS register */
> + char name[16]; /* Register name */
const char *reg_name;
> +} I2CRegMap;
> +
> +/*
> + * The register values in the common code is different than the latest
> + * register numbers as per the spec hence add the conversion map
> + */
> +static const I2CRegMap tpm_tis_reg_map[] = {
> + /*
> + * These registers are sent to TIS layer. The register with UNKNOWN
> + * mapping are not sent to TIS layer and handled in I2c layer.
> + * NOTE: Adding frequently used registers at the start
> + */
> + { TPM_I2C_REG_DATA_FIFO, TPM_TIS_REG_DATA_FIFO, "FIFO", },
> + { TPM_I2C_REG_STS, TPM_TIS_REG_STS, "STS", },
> + { TPM_I2C_REG_DATA_CSUM_GET, TPM_I2C_REG_UNKNOWN, "CSUM_GET", },
> + { TPM_I2C_REG_LOC_SEL, TPM_I2C_REG_UNKNOWN, "LOC_SEL", },
> + { TPM_I2C_REG_ACCESS, TPM_TIS_REG_ACCESS, "ACCESS", },
> + { TPM_I2C_REG_INT_ENABLE, TPM_TIS_REG_INT_ENABLE, "INTR_ENABLE",},
> + { TPM_I2C_REG_INT_CAPABILITY, TPM_TIS_REG_INT_ENABLE, "INTR_CAP", },
> + { TPM_I2C_REG_INTF_CAPABILITY, TPM_TIS_REG_INTF_CAPABILITY, "INTF_CAP", },
> + { TPM_I2C_REG_DID_VID, TPM_TIS_REG_DID_VID, "DID_VID", },
> + { TPM_I2C_REG_RID, TPM_TIS_REG_RID, "RID", },
> + { TPM_I2C_REG_I2C_DEV_ADDRESS, TPM_I2C_REG_UNKNOWN, "DEV_ADDRESS",},
> + { TPM_I2C_REG_DATA_CSUM_ENABLE, TPM_I2C_REG_UNKNOWN, "CSUM_ENABLE",},
> +};
> +
> +static int tpm_tis_i2c_pre_save(void *opaque)
> +{
> + TPMStateI2C *i2cst = opaque;
> +
> + return tpm_tis_pre_save(&i2cst->state);
> +}
> +
> +static int tpm_tis_i2c_post_load(void *opaque, int version_id)
> +{
> + TPMStateI2C *i2cst = opaque;
> +
> + if (i2cst->offset >= 1) {
> + tpm_tis_i2c_to_tis_reg(i2cst, i2cst->data[0]);
> + }
> +
> + return 0;
> +}
> +
> +static const VMStateDescription vmstate_tpm_tis_i2c = {
> + .name = "tpm-tis-i2c",
> + .version_id = 0,
> + .pre_save = tpm_tis_i2c_pre_save,
> + .post_load = tpm_tis_i2c_post_load,
> + .fields = (VMStateField[]) {
> + VMSTATE_BUFFER(state.buffer, TPMStateI2C),
> + VMSTATE_UINT16(state.rw_offset, TPMStateI2C),
> + VMSTATE_UINT8(state.active_locty, TPMStateI2C),
> + VMSTATE_UINT8(state.aborting_locty, TPMStateI2C),
> + VMSTATE_UINT8(state.next_locty, TPMStateI2C),
> +
> + VMSTATE_STRUCT_ARRAY(state.loc, TPMStateI2C, TPM_TIS_NUM_LOCALITIES, 0,
> + vmstate_locty, TPMLocality),
> +
> + /* i2c specifics */
> + VMSTATE_UINT8(offset, TPMStateI2C),
> + VMSTATE_UINT8(operation, TPMStateI2C),
> + VMSTATE_BUFFER(data, TPMStateI2C),
> + VMSTATE_UINT8(loc_sel, TPMStateI2C),
> + VMSTATE_UINT8(csum_enable, TPMStateI2C),
> +
> + VMSTATE_END_OF_LIST()
> + }
> +};
> +
> +/*
> + * Generate interface capability based on what is returned by TIS and what is
> + * expected by I2C. Save the capability in the data array overwriting the TIS
> + * capability.
> + */
> +static uint32_t tpm_i2c_interface_capability(TPMStateI2C *i2cst,
> + uint32_t tis_cap)
> +{
> + uint32_t i2c_cap = 0;
There's no need to initialize it...
> +
> + /* Now generate i2c capability */
> + i2c_cap = (TPM_I2C_CAP_INTERFACE_TYPE |
> + TPM_I2C_CAP_INTERFACE_VER |
> + TPM_I2C_CAP_TPM2_FAMILY |
> + TPM_I2C_CAP_LOCALITY_CAP |
> + TPM_I2C_CAP_BUS_SPEED |
> + TPM_I2C_CAP_DEV_ADDR_CHANGE);
> +
> + /* Now check the TIS and set some capabilities */
> +
> + /* Static burst count set */
> + if (tis_cap & TPM_TIS_CAP_BURST_COUNT_STATIC) {
> + i2c_cap |= TPM_I2C_CAP_BURST_COUNT_STATIC;
> + }
> +
> + return i2c_cap;
> +}
> +
> +/* Convert I2C register to TIS address and returns the name of the register */
> +static inline void tpm_tis_i2c_to_tis_reg(TPMStateI2C *i2cst, uint8_t i2c_reg)
> +{
> + const I2CRegMap *reg_map;
> + int i;
> +
> + i2cst->tis_addr = 0xffffffff;
> +
> + for (i = 0; i < ARRAY_SIZE(tpm_tis_reg_map); i++) {
> + reg_map = &tpm_tis_reg_map[i];
> + if (reg_map->i2c_reg == i2c_reg) {
> + i2cst->reg_name = reg_map->name;
i2cst->reg_name = reg_map->reg_name;
> + i2cst->tis_addr = reg_map->tis_reg;
> + if (i2cst->loc_sel != TPM_TIS_NO_LOCALITY) {
> + /* Include the locality in the address. */
> + i2cst->tis_addr += (i2cst->loc_sel << TPM_TIS_LOCALITY_SHIFT);
> + }
> + break;
> + }
> + }
> +
> + if (i2cst->tis_addr == 0xffffffff) {
> + qemu_log_mask(LOG_UNIMP, "%s: Could not convert i2c register: 0x%X\n",
> + __func__, i2cst->data[0]);
> + }
> +}
> +
> +/* Clear some fields from the structure. */
> +static inline void tpm_tis_i2c_clear_data(TPMStateI2C *i2cst)
> +{
> + /* Clear operation and offset */
> + i2cst->operation = 0;
> + i2cst->offset = 0;
> + i2cst->tis_addr = 0xffffffff;
> + i2cst->reg_name = NULL;
> + memset(i2cst->data, 0, sizeof(i2cst->data));
> +
> + return;
> +}
> +
> +/* Send data to TPM */
> +static inline void tpm_tis_i2c_tpm_send(TPMStateI2C *i2cst)
> +{
> + uint32_t data;
> +
> + if ((i2cst->operation == OP_SEND) && (i2cst->offset > 1)) {
> +
> + switch (i2cst->data[0]) {
> + case TPM_I2C_REG_DATA_CSUM_ENABLE:
> + /*
> + * Checksum is not handled by TIS code hence we will consume the
> + * register here.
> + */
> + i2cst->csum_enable = TPM_DATA_CSUM_ENABLED;
> + break;
> + case TPM_I2C_REG_DATA_FIFO:
> + /* Handled in the main i2c_send function */
> + break;
> + case TPM_I2C_REG_LOC_SEL:
> + /*
> + * This register is not handled by TIS so save the locality
> + * locally
> + */
> + i2cst->loc_sel = i2cst->data[1];
> + break;
> + default:
> + /* We handle non-FIFO here */
> +
> + /* Index 0 is a register. Convert byte stream to uint32_t */
> + data = i2cst->data[1];
> + data |= i2cst->data[2] << 8;
> + data |= i2cst->data[3] << 16;
> + data |= i2cst->data[4] << 24;
> +
> + /* Add register specific masking */
> + switch (i2cst->data[0]) {
> + case TPM_I2C_REG_INT_ENABLE:
> + data &= TPM_I2C_INT_ENABLE_MASK;
> + break;
> + }
> +
> + tpm_tis_write_data(&i2cst->state, i2cst->tis_addr, data, 4);
> + break;
> + }
> +
> + tpm_tis_i2c_clear_data(i2cst);
> + }
> +
> + return;
> +}
> +
> +/* Callback from TPM to indicate that response is copied */
> +static void tpm_tis_i2c_request_completed(TPMIf *ti, int ret)
> +{
> + TPMStateI2C *i2cst = TPM_TIS_I2C(ti);
> + TPMState *s = &i2cst->state;
> +
> + /* Inform the common code. */
> + tpm_tis_request_completed(s, ret);
> +}
> +
> +static enum TPMVersion tpm_tis_i2c_get_tpm_version(TPMIf *ti)
> +{
> + TPMStateI2C *i2cst = TPM_TIS_I2C(ti);
> + TPMState *s = &i2cst->state;
> +
> + return tpm_tis_get_tpm_version(s);
> +}
> +
> +static int tpm_tis_i2c_event(I2CSlave *i2c, enum i2c_event event)
> +{
> + TPMStateI2C *i2cst = TPM_TIS_I2C(i2c);
> + int ret = 0;
> +
> + switch (event) {
> + case I2C_START_RECV:
> + trace_tpm_tis_i2c_event("START_RECV");
> + break;
> + case I2C_START_SEND:
> + trace_tpm_tis_i2c_event("START_SEND");
> + tpm_tis_i2c_clear_data(i2cst);
> + break;
> + case I2C_FINISH:
> + trace_tpm_tis_i2c_event("FINISH");
> + if (i2cst->operation == OP_SEND) {
> + tpm_tis_i2c_tpm_send(i2cst);
> + } else {
> + tpm_tis_i2c_clear_data(i2cst);
> + }
> + break;
> + default:
> + break;
> + }
> +
> + return ret;
> +}
> +
> +/*
> + * If data is for FIFO then it is received from tpm_tis_common buffer
> + * otherwise it will be handled using single call to common code and
> + * cached in the local buffer.
> + */
> +static uint8_t tpm_tis_i2c_recv(I2CSlave *i2c)
> +{
> + int ret = 0;
> + uint32_t data_read;
> + TPMStateI2C *i2cst = TPM_TIS_I2C(i2c);
> + TPMState *s = &i2cst->state;
> + uint16_t i2c_reg = i2cst->data[0];
> +
> + if (i2cst->operation == OP_RECV) {
> +
> + /* Do not cache FIFO data. */
> + if (i2cst->data[0] == TPM_I2C_REG_DATA_FIFO) {
> + data_read = tpm_tis_read_data(s, i2cst->tis_addr, 1);
> + ret = (data_read & 0xff);
> + } else if (sizeof(i2cst->data)) {
if (i2cst->offset < sizeof(i2cst->data))
> + ret = i2cst->data[i2cst->offset++];
> + }
> +
> + } else if ((i2cst->operation == OP_SEND) && (i2cst->offset < 2)) {
> + /* First receive call after send */
> +
> + i2cst->operation = OP_RECV;
> +
> + switch (i2c_reg) {
> + case TPM_I2C_REG_LOC_SEL:
> + /* Location selection register is managed by i2c */
> + i2cst->data[1] = i2cst->loc_sel;
> + break;
> + case TPM_I2C_REG_DATA_FIFO:
> + /* FIFO data is directly read from TPM TIS */
> + data_read = tpm_tis_read_data(s, i2cst->tis_addr, 1);
> + i2cst->data[1] = (data_read & 0xff);
> + break;
> + case TPM_I2C_REG_DATA_CSUM_ENABLE:
> + i2cst->data[1] = i2cst->csum_enable;
> + break;
> + case TPM_I2C_REG_DATA_CSUM_GET:
> + /*
> + * Checksum registers are not supported by common code hence
> + * call a common code to get the checksum.
> + */
> + data_read = tpm_tis_get_checksum(s);
> +
> + /* Save the byte stream in data field */
> + i2cst->data[1] = (data_read & 0xff);
> + i2cst->data[2] = ((data_read >> 8) & 0xff);
> + break;
> + default:
> + data_read = tpm_tis_read_data(s, i2cst->tis_addr, 4);
> +
For consistency with all the other register please use a switch here as well:
switch (i2c_reg)
case TPM_I2C_REG_INTF_CAPABILITY:
> + if (i2c_reg == TPM_I2C_REG_INTF_CAPABILITY) {
> + /* Prepare the capabilities as per I2C interface */
> + data_read = tpm_i2c_interface_capability(i2cst,
> + data_read);
> + } else if (i2c_reg == TPM_I2C_REG_STS) {
> + /*
> + * As per specs, STS bit 31:26 are reserved and must
> + * be set to 0
> + */
> + data_read &= TPM_I2C_STS_READ_MASK;
> + }
> + /* Save byte stream in data[] */
> + i2cst->data[1] = data_read;
> + i2cst->data[2] = data_read >> 8;
> + i2cst->data[3] = data_read >> 16;
> + i2cst->data[4] = data_read >> 24;
> + break;
> + }
> +
> +
please remove 2nd empty line
> + /* Return first byte with this call */
> + i2cst->offset = 1; /* keep the register value intact for debug */
> + ret = i2cst->data[i2cst->offset++];
> + } else {
> + i2cst->operation = OP_RECV;
> + }
> +
> + trace_tpm_tis_i2c_recv(ret);
> +
> + return ret;
> +}
> +
> +/*
> + * Send function only remembers data in the buffer and then calls
> + * TPM TIS common code during FINISH event.
> + */
> +static int tpm_tis_i2c_send(I2CSlave *i2c, uint8_t data)
> +{
> + TPMStateI2C *i2cst = TPM_TIS_I2C(i2c);
> +
> + /* Reject non-supported registers. */
> + if (i2cst->offset == 0) {
> + /* Convert I2C register to TIS register */
> + tpm_tis_i2c_to_tis_reg(i2cst, data);
> + if (i2cst->tis_addr == 0xffffffff) {
> + return 0xffffffff;
> + }
> +
> + trace_tpm_tis_i2c_send_reg(i2cst->reg_name, data);
> +
> + /* We do not support device address change */
> + if (data == TPM_I2C_REG_I2C_DEV_ADDRESS) {
> + qemu_log_mask(LOG_UNIMP, "%s: Device address change "
> + "is not supported.\n", __func__);
> + return 0xffffffff;
> + }
> + } else {
> + trace_tpm_tis_i2c_send(data);
> + }
> +
> + if (i2cst->offset < sizeof(i2cst->data)) {
> + i2cst->operation = OP_SEND;
> +
> + /* Remember data locally for non-FIFO registers */
> + if ((i2cst->offset == 0) ||
> + (i2cst->data[0] != TPM_I2C_REG_DATA_FIFO)) {
> + i2cst->data[i2cst->offset++] = data;
> + } else {
> + tpm_tis_write_data(&i2cst->state, i2cst->tis_addr, data, 1);
> + }
> +
> + return 0;
> +
> + } else {
> + /* Return non-zero to indicate NAK */
> + return 1;
The 'else' is not needed. Just 'return 1'.
> + }
> +}
> +
> +static Property tpm_tis_i2c_properties[] = {
> + DEFINE_PROP_UINT32("irq", TPMStateI2C, state.irq_num, TPM_TIS_IRQ),
> + DEFINE_PROP_TPMBE("tpmdev", TPMStateI2C, state.be_driver),
> + DEFINE_PROP_END_OF_LIST(),
> +};
> +
> +static void tpm_tis_i2c_realizefn(DeviceState *dev, Error **errp)
> +{
> + TPMStateI2C *i2cst = TPM_TIS_I2C(dev);
> + TPMState *s = &i2cst->state;
> +
> + if (!tpm_find()) {
> + error_setg(errp, "at most one TPM device is permitted");
> + return;
> + }
> +
> + /*
> + * Get the backend pointer. It is not initialized propery during
> + * device_class_set_props
> + */
> + s->be_driver = qemu_find_tpm_be("tpm0");
> +
> + if (!s->be_driver) {
> + error_setg(errp, "'tpmdev' property is required");
> + return;
> + }
> + if (s->irq_num > 15) {
> + error_setg(errp, "IRQ %d is outside valid range of 0 to 15",
> + s->irq_num);
> + return;
> + }
> +}
> +
> +static void tpm_tis_i2c_reset(DeviceState *dev)
> +{
> + TPMStateI2C *i2cst = TPM_TIS_I2C(dev);
> + TPMState *s = &i2cst->state;
> +
> + tpm_tis_i2c_clear_data(i2cst);
> +
> + i2cst->csum_enable = 0;
> + i2cst->loc_sel = TPM_TIS_NO_LOCALITY;
Per i2c spec 6.5.1 this has to be 0 by default.
> +
> + return tpm_tis_reset(s);
> +}
> +
> +static void tpm_tis_i2c_class_init(ObjectClass *klass, void *data)
> +{
> + DeviceClass *dc = DEVICE_CLASS(klass);
> + I2CSlaveClass *k = I2C_SLAVE_CLASS(klass);
> + TPMIfClass *tc = TPM_IF_CLASS(klass);
> +
> + dc->realize = tpm_tis_i2c_realizefn;
> + dc->reset = tpm_tis_i2c_reset;
> + dc->vmsd = &vmstate_tpm_tis_i2c;
> + device_class_set_props(dc, tpm_tis_i2c_properties);
> +
> + k->event = tpm_tis_i2c_event;
> + k->recv = tpm_tis_i2c_recv;
> + k->send = tpm_tis_i2c_send;
> +
> + tc->model = TPM_MODEL_TPM_TIS;
> + tc->request_completed = tpm_tis_i2c_request_completed;
> + tc->get_version = tpm_tis_i2c_get_tpm_version;
isa and sysbus devices call this:
set_bit(DEVICE_CATEGORY_MISC, dc->categories);
The i2c should probably also have it.
> +}
> +
> +static const TypeInfo tpm_tis_i2c_info = {
> + .name = TYPE_TPM_TIS_I2C,
> + .parent = TYPE_I2C_SLAVE,
> + .instance_size = sizeof(TPMStateI2C),
We will need an init function here to be able to call sysbus_init_irq()
static void tpm_tis_i2c_initfn(Object *obj)
{
TPMStateI2C *i2cst = TPM_TIS_I2C(obj);
TPMState *s = &i2cst->state;
sysbus_init_irq(SYS_BUS_DEVICE(obj), &s->irq);
}
Without this, Linux will probably have to use the driver in polling mode. Maybe it will switch to interrupt mode once this is called.
Due to the insights given in i2c spec table 11 I now have 3 patches on top of your v6: https://github.com/stefanberger/qemu-tpm/commits/tpm-i2c.v6
Thanks!
Regards,
Stefan
> + .class_init = tpm_tis_i2c_class_init,
> + .interfaces = (InterfaceInfo[]) {
> + { TYPE_TPM_IF },
> + { }
> + }
> +};
> +
> +static void tpm_tis_i2c_register_types(void)
> +{
> + type_register_static(&tpm_tis_i2c_info);
> +}
> +
> +type_init(tpm_tis_i2c_register_types)
> diff --git a/hw/tpm/trace-events b/hw/tpm/trace-events
> index f17110458e..fa882dfefe 100644
> --- a/hw/tpm/trace-events
> +++ b/hw/tpm/trace-events
> @@ -36,3 +36,9 @@ tpm_spapr_do_crq_unknown_msg_type(uint8_t type) "Unknown message type 0x%02x"
> tpm_spapr_do_crq_unknown_crq(uint8_t raw1, uint8_t raw2) "unknown CRQ 0x%02x 0x%02x ..."
> tpm_spapr_post_load(void) "Delivering TPM response after resume"
> tpm_spapr_caught_response(uint32_t v) "Caught response to deliver after resume: %u bytes"
> +
> +# tpm_tis_i2c.c
> +tpm_tis_i2c_recv(uint8_t data) "TPM I2C read: 0x%X"
> +tpm_tis_i2c_send(uint8_t data) "TPM I2C write: 0x%X"
> +tpm_tis_i2c_event(const char *event) "TPM I2C event: %s"
> +tpm_tis_i2c_send_reg(const char *name, int reg) "TPM I2C write register: %s(0x%X)"
> diff --git a/include/sysemu/tpm.h b/include/sysemu/tpm.h
> index fb40e30ff6..66e3b45f30 100644
> --- a/include/sysemu/tpm.h
> +++ b/include/sysemu/tpm.h
> @@ -48,6 +48,7 @@ struct TPMIfClass {
> #define TYPE_TPM_TIS_SYSBUS "tpm-tis-device"
> #define TYPE_TPM_CRB "tpm-crb"
> #define TYPE_TPM_SPAPR "tpm-spapr"
> +#define TYPE_TPM_TIS_I2C "tpm-tis-i2c"
>
> #define TPM_IS_TIS_ISA(chr) \
> object_dynamic_cast(OBJECT(chr), TYPE_TPM_TIS_ISA)
> @@ -57,6 +58,8 @@ struct TPMIfClass {
> object_dynamic_cast(OBJECT(chr), TYPE_TPM_CRB)
> #define TPM_IS_SPAPR(chr) \
> object_dynamic_cast(OBJECT(chr), TYPE_TPM_SPAPR)
> +#define TPM_IS_TIS_I2C(chr) \
> + object_dynamic_cast(OBJECT(chr), TYPE_TPM_TIS_I2C)
>
> /* returns NULL unless there is exactly one TPM device */
> static inline TPMIf *tpm_find(void)
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v6 3/3] tpm: Add support for TPM device over I2C bus
2023-03-26 13:00 ` Stefan Berger
@ 2023-03-26 22:23 ` Ninad Palsule
0 siblings, 0 replies; 6+ messages in thread
From: Ninad Palsule @ 2023-03-26 22:23 UTC (permalink / raw)
To: Stefan Berger, Ninad Palsule, qemu-devel; +Cc: joel, andrew, clg
Hi Stephan,
On 3/26/23 8:00 AM, Stefan Berger wrote:
>
>
> On 3/25/23 22:38, Ninad Palsule wrote:
>> Qemu already supports devices attached to ISA and sysbus. This drop adds
>> support for the I2C bus attached TPM devices. I2C model only supports
>> TPM2 protocol.
>>
>> This commit includes changes for the common code.
>> - Added I2C emulation model. Logic was added in the model to temporarily
>> cache the data as I2C interface works per byte basis.
>> - New tpm type "tpm-tis-i2c" added for I2C support. The user has to
>> provide this string on command line.
>>
>> Testing:
>> TPM I2C device module is tested using SWTPM (software based TPM
>> package). Qemu uses the rainier machine and is connected to swtpm
>> over
>> the socket interface.
>>
>> The command to start swtpm is as follows:
>> $ swtpm socket --tpmstate dir=/tmp/mytpm1 \
>> --ctrl type=unixio,path=/tmp/mytpm1/swtpm-sock \
>> --tpm2 --log level=100
>>
>> The command to start qemu is as follows:
>> $ qemu-system-arm -M rainier-bmc -nographic \
>> -kernel ${IMAGEPATH}/fitImage-linux.bin \
>> -dtb ${IMAGEPATH}/aspeed-bmc-ibm-rainier.dtb \
>> -initrd
>> ${IMAGEPATH}/obmc-phosphor-initramfs.rootfs.cpio.xz \
>> -drive
>> file=${IMAGEPATH}/obmc-phosphor-image.rootfs.wic.qcow2,if=sd,index=2 \
>> -net nic -net
>> user,hostfwd=:127.0.0.1:2222-:22,hostfwd=:127.0.0.1:2443-:443 \
>> -chardev socket,id=chrtpm,path=/tmp/mytpm1/swtpm-sock \
>> -tpmdev emulator,id=tpm0,chardev=chrtpm \
>> -device
>> tpm-tis-i2c,tpmdev=tpm0,bus=aspeed.i2c.bus.12,address=0x2e
>>
>> Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
>> ---
>> V2:
>> Incorporated Stephen's review comments.
>> - Handled checksum related register in I2C layer
>> - Defined I2C interface capabilities and return those instead of
>> capabilities from TPM TIS. Add required capabilities from TIS.
>> - Do not cache FIFO data in the I2C layer.
>> - Make sure that Device address change register is not passed to I2C
>> layer as capability indicate that it is not supported.
>> - Added boundary checks.
>> - Make sure that bits 26-31 are zeroed for the TPM_STS register on read
>> - Updated Kconfig files for new define.
>>
>> ---
>> V3:
>> - Moved processing of register TPM_I2C_LOC_SEL in the I2C. So I2C layer
>> remembers the locality and pass it to TIS on each read/write.
>> - The write data is no more cached in the I2C layer so the buffer size
>> is reduced to 16 bytes.
>> - Checksum registers are now managed by the I2C layer. Added new
>> function in TIS layer to return the checksum and used that to process
>> the request.
>> - Now 2-4 byte register value will be passed to TIS layer in a single
>> write call instead of 1 byte at a time. Added functions to convert
>> between little endian stream of bytes to single 32 bit unsigned
>> integer. Similarly 32 bit integer to stream of bytes.
>> - Added restriction on device change register.
>> - Replace few if-else statement with switch statement for clarity.
>> - Log warning when unknown register is received.
>> - Moved all register definations to acpi/tmp.h
>>
>> ---
>> V4:
>> Incorporated review comments from Cedric and Stefan.
>> - Reduced data[] size from 16 byte to 5 bytes.
>> - Added register name in the mapping table which can be used for
>> tracing.
>> - Removed the endian conversion functions instead used simple logic
>> provided by Stefan.
>> - Rename I2C registers to reduce the length.
>> - Added traces for send, recv and event functions. You can turn on trace
>> on command line by using "-trace "tpm_tis_i2c*" option.
>>
>> ---
>> V5:
>> Fixed issues reported by Stefan's test.
>> - Added mask for the INT_ENABLE register.
>> - Use correct TIS register for reading interrupt capability.
>> - Cleanup how register is converted from I2C to TIS and also saved
>> information like tis_addr and register name in the i2cst so that we
>> can only convert it once on i2c_send.
>> - Trace register number for unknown registers.
>>
>> ---
>> V6:
>> Fixed review comments from Stefan.
>> - Fixed some variable size.
>> - Removed unused variables.
>> - Added vmstat backin to handle migration.
>> - Added post load phase to reload tis address and register name.
>> ---
>> hw/arm/Kconfig | 1 +
>> hw/tpm/Kconfig | 7 +
>> hw/tpm/meson.build | 1 +
>> hw/tpm/tpm_tis_i2c.c | 533 +++++++++++++++++++++++++++++++++++++++++++
>> hw/tpm/trace-events | 6 +
>> include/sysemu/tpm.h | 3 +
>> 6 files changed, 551 insertions(+)
>> create mode 100644 hw/tpm/tpm_tis_i2c.c
>>
>> diff --git a/hw/arm/Kconfig b/hw/arm/Kconfig
>> index b5aed4aff5..05d6ef1a31 100644
>> --- a/hw/arm/Kconfig
>> +++ b/hw/arm/Kconfig
>> @@ -6,6 +6,7 @@ config ARM_VIRT
>> imply VFIO_PLATFORM
>> imply VFIO_XGMAC
>> imply TPM_TIS_SYSBUS
>> + imply TPM_TIS_I2C
>> imply NVDIMM
>> select ARM_GIC
>> select ACPI
>> diff --git a/hw/tpm/Kconfig b/hw/tpm/Kconfig
>> index 29e82f3c92..a46663288c 100644
>> --- a/hw/tpm/Kconfig
>> +++ b/hw/tpm/Kconfig
>> @@ -1,3 +1,10 @@
>> +config TPM_TIS_I2C
>> + bool
>> + depends on TPM
>> + select TPM_BACKEND
>> + select I2C
>> + select TPM_TIS
>> +
>> config TPM_TIS_ISA
>> bool
>> depends on TPM && ISA_BUS
>> diff --git a/hw/tpm/meson.build b/hw/tpm/meson.build
>> index 7abc2d794a..76fe3cb098 100644
>> --- a/hw/tpm/meson.build
>> +++ b/hw/tpm/meson.build
>> @@ -1,6 +1,7 @@
>> softmmu_ss.add(when: 'CONFIG_TPM_TIS', if_true:
>> files('tpm_tis_common.c'))
>> softmmu_ss.add(when: 'CONFIG_TPM_TIS_ISA', if_true:
>> files('tpm_tis_isa.c'))
>> softmmu_ss.add(when: 'CONFIG_TPM_TIS_SYSBUS', if_true:
>> files('tpm_tis_sysbus.c'))
>> +softmmu_ss.add(when: 'CONFIG_TPM_TIS_I2C', if_true:
>> files('tpm_tis_i2c.c'))
>> softmmu_ss.add(when: 'CONFIG_TPM_CRB', if_true: files('tpm_crb.c'))
>> softmmu_ss.add(when: 'CONFIG_TPM_TIS', if_true: files('tpm_ppi.c'))
>> softmmu_ss.add(when: 'CONFIG_TPM_CRB', if_true: files('tpm_ppi.c'))
>> diff --git a/hw/tpm/tpm_tis_i2c.c b/hw/tpm/tpm_tis_i2c.c
>> new file mode 100644
>> index 0000000000..1e60dadb72
>> --- /dev/null
>> +++ b/hw/tpm/tpm_tis_i2c.c
>> @@ -0,0 +1,533 @@
>> +/*
>> + * tpm_tis_i2c.c - QEMU's TPM TIS I2C Device
>> + *
>> + * This work is licensed under the terms of the GNU GPL, version 2
>> or later.
>> + * See the COPYING file in the top-level directory.
>> + *
>> + * Implementation of the TIS interface according to specs found at
>> + * http://www.trustedcomputinggroup.org. This implementation currently
>> + * supports version 1.3, 21 March 2013
>> + * In the developers menu choose the PC Client section then find the
>> TIS
>> + * specification.
>> + *
>> + * TPM TIS for TPM 2 implementation following TCG PC Client Platform
>> + * TPM Profile (PTP) Specification, Familiy 2.0, Revision 00.43
>> + *
>> + * TPM I2C implementation follows TCG TPM I2c Interface specification,
>> + * Family 2.0, Level 00, Revision 1.00
>> + */
>> +
>> +#include "qemu/osdep.h"
>> +#include "hw/i2c/i2c.h"
>> +#include "hw/qdev-properties.h"
>
>
> This one is not needed.
Removed
>
>> +#include "hw/acpi/tpm.h"
>> +#include "migration/vmstate.h"
>> +#include "tpm_prop.h"
>> +#include "qom/object.h"
>> +#include "block/aio.h"
>> +#include "qemu/main-loop.h"
>
> The above 3 are not needed.
Removed
>
>> +#include "qemu/log.h"
>> +#include "trace.h"
>> +#include "tpm_tis.h"
>> +
>> +/* TPM_STS mask for read bits 31:26 must be zero */
>> +#define TPM_I2C_STS_READ_MASK 0x03ffffff
>> +
>> +/* Checksum enabled. */
>> +#define TPM_DATA_CSUM_ENABLED 0x1
>
> Can you move this to the public header file? I'd use it in the test
> cases as well.
Moved
>
>> +
>> +/* TPM_I2C_INT_ENABLE mask */
>> +#define TPM_I2C_INT_ENABLE_MASK (TPM_TIS_INT_ENABLED | \
>> + TPM_TIS_INT_DATA_AVAILABLE | \
>> + TPM_TIS_INT_STS_VALID | \
>> + TPM_TIS_INT_LOCALITY_CHANGED | \
>> + TPM_TIS_INT_COMMAND_READY)
>> +
>> +/* Operations */
>> +#define OP_SEND 1
>> +#define OP_RECV 2
>> +
>> +typedef struct TPMStateI2C {
>> + /*< private >*/
>> + I2CSlave parent_obj;
>> +
>> + uint8_t offset; /* offset into data[] */
>> + uint8_t operation; /* OP_SEND & OP_RECV */
>> + uint8_t data[5]; /* Data */
>> +
>> + /* i2c registers */
>> + uint8_t loc_sel; /* Current locality */
>> + uint8_t csum_enable; /* Is checksum enabled */
>> +
>> + /* Derived from the above */
>> + const char *reg_name; /* Register name */
>> + uint32_t tis_addr; /* Converted tis address including
>> locty */
>> +
>> + /*< public >*/
>> + TPMState state; /* not a QOM object */
>> +
>> +} TPMStateI2C;
>> +
>> +DECLARE_INSTANCE_CHECKER(TPMStateI2C, TPM_TIS_I2C,
>> + TYPE_TPM_TIS_I2C)
>> +
>> +/* Prototype */
>> +static inline void tpm_tis_i2c_to_tis_reg(TPMStateI2C *i2cst,
>> uint8_t i2c_reg);
>> +
>> +/* Register map */
>> +typedef struct regMap {
>> + uint8_t i2c_reg; /* I2C register */
>> + uint16_t tis_reg; /* TIS register */
>> + char name[16]; /* Register name */
>
> const char *reg_name;
done
>
>> +} I2CRegMap;
>> +
>> +/*
>> + * The register values in the common code is different than the latest
>> + * register numbers as per the spec hence add the conversion map
>> + */
>> +static const I2CRegMap tpm_tis_reg_map[] = {
>> + /*
>> + * These registers are sent to TIS layer. The register with UNKNOWN
>> + * mapping are not sent to TIS layer and handled in I2c layer.
>> + * NOTE: Adding frequently used registers at the start
>> + */
>> + { TPM_I2C_REG_DATA_FIFO, TPM_TIS_REG_DATA_FIFO,
>> "FIFO", },
>> + { TPM_I2C_REG_STS, TPM_TIS_REG_STS, "STS", },
>> + { TPM_I2C_REG_DATA_CSUM_GET, TPM_I2C_REG_UNKNOWN,
>> "CSUM_GET", },
>> + { TPM_I2C_REG_LOC_SEL, TPM_I2C_REG_UNKNOWN, "LOC_SEL", },
>> + { TPM_I2C_REG_ACCESS, TPM_TIS_REG_ACCESS, "ACCESS", },
>> + { TPM_I2C_REG_INT_ENABLE, TPM_TIS_REG_INT_ENABLE,
>> "INTR_ENABLE",},
>> + { TPM_I2C_REG_INT_CAPABILITY, TPM_TIS_REG_INT_ENABLE,
>> "INTR_CAP", },
>> + { TPM_I2C_REG_INTF_CAPABILITY, TPM_TIS_REG_INTF_CAPABILITY,
>> "INTF_CAP", },
>> + { TPM_I2C_REG_DID_VID, TPM_TIS_REG_DID_VID, "DID_VID", },
>> + { TPM_I2C_REG_RID, TPM_TIS_REG_RID, "RID", },
>> + { TPM_I2C_REG_I2C_DEV_ADDRESS, TPM_I2C_REG_UNKNOWN,
>> "DEV_ADDRESS",},
>> + { TPM_I2C_REG_DATA_CSUM_ENABLE, TPM_I2C_REG_UNKNOWN,
>> "CSUM_ENABLE",},
>> +};
>> +
>> +static int tpm_tis_i2c_pre_save(void *opaque)
>> +{
>> + TPMStateI2C *i2cst = opaque;
>> +
>> + return tpm_tis_pre_save(&i2cst->state);
>> +}
>> +
>> +static int tpm_tis_i2c_post_load(void *opaque, int version_id)
>> +{
>> + TPMStateI2C *i2cst = opaque;
>> +
>> + if (i2cst->offset >= 1) {
>> + tpm_tis_i2c_to_tis_reg(i2cst, i2cst->data[0]);
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static const VMStateDescription vmstate_tpm_tis_i2c = {
>> + .name = "tpm-tis-i2c",
>> + .version_id = 0,
>> + .pre_save = tpm_tis_i2c_pre_save,
>> + .post_load = tpm_tis_i2c_post_load,
>> + .fields = (VMStateField[]) {
>> + VMSTATE_BUFFER(state.buffer, TPMStateI2C),
>> + VMSTATE_UINT16(state.rw_offset, TPMStateI2C),
>> + VMSTATE_UINT8(state.active_locty, TPMStateI2C),
>> + VMSTATE_UINT8(state.aborting_locty, TPMStateI2C),
>> + VMSTATE_UINT8(state.next_locty, TPMStateI2C),
>> +
>> + VMSTATE_STRUCT_ARRAY(state.loc, TPMStateI2C,
>> TPM_TIS_NUM_LOCALITIES, 0,
>> + vmstate_locty, TPMLocality),
>> +
>> + /* i2c specifics */
>> + VMSTATE_UINT8(offset, TPMStateI2C),
>> + VMSTATE_UINT8(operation, TPMStateI2C),
>> + VMSTATE_BUFFER(data, TPMStateI2C),
>> + VMSTATE_UINT8(loc_sel, TPMStateI2C),
>> + VMSTATE_UINT8(csum_enable, TPMStateI2C),
>> +
>> + VMSTATE_END_OF_LIST()
>> + }
>> +};
>> +
>> +/*
>> + * Generate interface capability based on what is returned by TIS
>> and what is
>> + * expected by I2C. Save the capability in the data array
>> overwriting the TIS
>> + * capability.
>> + */
>> +static uint32_t tpm_i2c_interface_capability(TPMStateI2C *i2cst,
>> + uint32_t tis_cap)
>> +{
>> + uint32_t i2c_cap = 0;
>
> There's no need to initialize it...
Removed.
>
>> +
>> + /* Now generate i2c capability */
>> + i2c_cap = (TPM_I2C_CAP_INTERFACE_TYPE |
>> + TPM_I2C_CAP_INTERFACE_VER |
>> + TPM_I2C_CAP_TPM2_FAMILY |
>> + TPM_I2C_CAP_LOCALITY_CAP |
>> + TPM_I2C_CAP_BUS_SPEED |
>> + TPM_I2C_CAP_DEV_ADDR_CHANGE);
>> +
>> + /* Now check the TIS and set some capabilities */
>> +
>> + /* Static burst count set */
>> + if (tis_cap & TPM_TIS_CAP_BURST_COUNT_STATIC) {
>> + i2c_cap |= TPM_I2C_CAP_BURST_COUNT_STATIC;
>> + }
>> +
>> + return i2c_cap;
>> +}
>> +
>> +/* Convert I2C register to TIS address and returns the name of the
>> register */
>> +static inline void tpm_tis_i2c_to_tis_reg(TPMStateI2C *i2cst,
>> uint8_t i2c_reg)
>> +{
>> + const I2CRegMap *reg_map;
>> + int i;
>> +
>> + i2cst->tis_addr = 0xffffffff;
>> +
>> + for (i = 0; i < ARRAY_SIZE(tpm_tis_reg_map); i++) {
>> + reg_map = &tpm_tis_reg_map[i];
>> + if (reg_map->i2c_reg == i2c_reg) {
>> + i2cst->reg_name = reg_map->name;
>
> i2cst->reg_name = reg_map->reg_name;
Done
>
>> + i2cst->tis_addr = reg_map->tis_reg;
>> + if (i2cst->loc_sel != TPM_TIS_NO_LOCALITY) {
>> + /* Include the locality in the address. */
>> + i2cst->tis_addr += (i2cst->loc_sel <<
>> TPM_TIS_LOCALITY_SHIFT);
>> + }
>> + break;
>> + }
>> + }
>> +
>> + if (i2cst->tis_addr == 0xffffffff) {
>> + qemu_log_mask(LOG_UNIMP, "%s: Could not convert i2c
>> register: 0x%X\n",
>> + __func__, i2cst->data[0]);
>> + }
>> +}
>> +
>> +/* Clear some fields from the structure. */
>> +static inline void tpm_tis_i2c_clear_data(TPMStateI2C *i2cst)
>> +{
>> + /* Clear operation and offset */
>> + i2cst->operation = 0;
>> + i2cst->offset = 0;
>> + i2cst->tis_addr = 0xffffffff;
>> + i2cst->reg_name = NULL;
>> + memset(i2cst->data, 0, sizeof(i2cst->data));
>> +
>> + return;
>> +}
>> +
>> +/* Send data to TPM */
>> +static inline void tpm_tis_i2c_tpm_send(TPMStateI2C *i2cst)
>> +{
>> + uint32_t data;
>> +
>> + if ((i2cst->operation == OP_SEND) && (i2cst->offset > 1)) {
>> +
>> + switch (i2cst->data[0]) {
>> + case TPM_I2C_REG_DATA_CSUM_ENABLE:
>> + /*
>> + * Checksum is not handled by TIS code hence we will
>> consume the
>> + * register here.
>> + */
>> + i2cst->csum_enable = TPM_DATA_CSUM_ENABLED;
>> + break;
>> + case TPM_I2C_REG_DATA_FIFO:
>> + /* Handled in the main i2c_send function */
>> + break;
>> + case TPM_I2C_REG_LOC_SEL:
>> + /*
>> + * This register is not handled by TIS so save the locality
>> + * locally
>> + */
>> + i2cst->loc_sel = i2cst->data[1];
>> + break;
>> + default:
>> + /* We handle non-FIFO here */
>> +
>> + /* Index 0 is a register. Convert byte stream to
>> uint32_t */
>> + data = i2cst->data[1];
>> + data |= i2cst->data[2] << 8;
>> + data |= i2cst->data[3] << 16;
>> + data |= i2cst->data[4] << 24;
>> +
>> + /* Add register specific masking */
>> + switch (i2cst->data[0]) {
>> + case TPM_I2C_REG_INT_ENABLE:
>> + data &= TPM_I2C_INT_ENABLE_MASK;
>> + break;
>> + }
>> +
>> + tpm_tis_write_data(&i2cst->state, i2cst->tis_addr, data,
>> 4);
>> + break;
>> + }
>> +
>> + tpm_tis_i2c_clear_data(i2cst);
>> + }
>> +
>> + return;
>> +}
>> +
>> +/* Callback from TPM to indicate that response is copied */
>> +static void tpm_tis_i2c_request_completed(TPMIf *ti, int ret)
>> +{
>> + TPMStateI2C *i2cst = TPM_TIS_I2C(ti);
>> + TPMState *s = &i2cst->state;
>> +
>> + /* Inform the common code. */
>> + tpm_tis_request_completed(s, ret);
>> +}
>> +
>> +static enum TPMVersion tpm_tis_i2c_get_tpm_version(TPMIf *ti)
>> +{
>> + TPMStateI2C *i2cst = TPM_TIS_I2C(ti);
>> + TPMState *s = &i2cst->state;
>> +
>> + return tpm_tis_get_tpm_version(s);
>> +}
>> +
>> +static int tpm_tis_i2c_event(I2CSlave *i2c, enum i2c_event event)
>> +{
>> + TPMStateI2C *i2cst = TPM_TIS_I2C(i2c);
>> + int ret = 0;
>> +
>> + switch (event) {
>> + case I2C_START_RECV:
>> + trace_tpm_tis_i2c_event("START_RECV");
>> + break;
>> + case I2C_START_SEND:
>> + trace_tpm_tis_i2c_event("START_SEND");
>> + tpm_tis_i2c_clear_data(i2cst);
>> + break;
>> + case I2C_FINISH:
>> + trace_tpm_tis_i2c_event("FINISH");
>> + if (i2cst->operation == OP_SEND) {
>> + tpm_tis_i2c_tpm_send(i2cst);
>> + } else {
>> + tpm_tis_i2c_clear_data(i2cst);
>> + }
>> + break;
>> + default:
>> + break;
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * If data is for FIFO then it is received from tpm_tis_common buffer
>> + * otherwise it will be handled using single call to common code and
>> + * cached in the local buffer.
>> + */
>> +static uint8_t tpm_tis_i2c_recv(I2CSlave *i2c)
>> +{
>> + int ret = 0;
>> + uint32_t data_read;
>> + TPMStateI2C *i2cst = TPM_TIS_I2C(i2c);
>> + TPMState *s = &i2cst->state;
>> + uint16_t i2c_reg = i2cst->data[0];
>> +
>> + if (i2cst->operation == OP_RECV) {
>> +
>> + /* Do not cache FIFO data. */
>> + if (i2cst->data[0] == TPM_I2C_REG_DATA_FIFO) {
>> + data_read = tpm_tis_read_data(s, i2cst->tis_addr, 1);
>> + ret = (data_read & 0xff);
>> + } else if (sizeof(i2cst->data)) {
>
>
> if (i2cst->offset < sizeof(i2cst->data))
Good catch. fixed.
>
>
>> + ret = i2cst->data[i2cst->offset++];
>> + }
>> +
>> + } else if ((i2cst->operation == OP_SEND) && (i2cst->offset < 2)) {
>> + /* First receive call after send */
>> +
>> + i2cst->operation = OP_RECV;
>> +
>> + switch (i2c_reg) {
>> + case TPM_I2C_REG_LOC_SEL:
>> + /* Location selection register is managed by i2c */
>> + i2cst->data[1] = i2cst->loc_sel;
>> + break;
>> + case TPM_I2C_REG_DATA_FIFO:
>> + /* FIFO data is directly read from TPM TIS */
>> + data_read = tpm_tis_read_data(s, i2cst->tis_addr, 1);
>> + i2cst->data[1] = (data_read & 0xff);
>> + break;
>> + case TPM_I2C_REG_DATA_CSUM_ENABLE:
>> + i2cst->data[1] = i2cst->csum_enable;
>> + break;
>> + case TPM_I2C_REG_DATA_CSUM_GET:
>> + /*
>> + * Checksum registers are not supported by common code
>> hence
>> + * call a common code to get the checksum.
>> + */
>> + data_read = tpm_tis_get_checksum(s);
>> +
>> + /* Save the byte stream in data field */
>> + i2cst->data[1] = (data_read & 0xff);
>> + i2cst->data[2] = ((data_read >> 8) & 0xff);
>> + break;
>> + default:
>> + data_read = tpm_tis_read_data(s, i2cst->tis_addr, 4);
>> +
>
> For consistency with all the other register please use a switch here
> as well:
>
> switch (i2c_reg)
> case TPM_I2C_REG_INTF_CAPABILITY:
Done
>
>> + if (i2c_reg == TPM_I2C_REG_INTF_CAPABILITY) {
>> + /* Prepare the capabilities as per I2C interface */
>> + data_read = tpm_i2c_interface_capability(i2cst,
>> + data_read);
>> + } else if (i2c_reg == TPM_I2C_REG_STS) {
>> + /*
>> + * As per specs, STS bit 31:26 are reserved and must
>> + * be set to 0
>> + */
>> + data_read &= TPM_I2C_STS_READ_MASK;
>> + }
>> + /* Save byte stream in data[] */
>> + i2cst->data[1] = data_read;
>> + i2cst->data[2] = data_read >> 8;
>> + i2cst->data[3] = data_read >> 16;
>> + i2cst->data[4] = data_read >> 24;
>> + break;
>> + }
>> +
>> +
>
> please remove 2nd empty line
Done
>
>> + /* Return first byte with this call */
>> + i2cst->offset = 1; /* keep the register value intact for
>> debug */
>> + ret = i2cst->data[i2cst->offset++];
>> + } else {
>> + i2cst->operation = OP_RECV;
>> + }
>> +
>> + trace_tpm_tis_i2c_recv(ret);
>> +
>> + return ret;
>> +}
>> +
>> +/*
>> + * Send function only remembers data in the buffer and then calls
>> + * TPM TIS common code during FINISH event.
>> + */
>> +static int tpm_tis_i2c_send(I2CSlave *i2c, uint8_t data)
>> +{
>> + TPMStateI2C *i2cst = TPM_TIS_I2C(i2c);
>> +
>> + /* Reject non-supported registers. */
>> + if (i2cst->offset == 0) {
>> + /* Convert I2C register to TIS register */
>> + tpm_tis_i2c_to_tis_reg(i2cst, data);
>> + if (i2cst->tis_addr == 0xffffffff) {
>> + return 0xffffffff;
>> + }
>> +
>> + trace_tpm_tis_i2c_send_reg(i2cst->reg_name, data);
>> +
>> + /* We do not support device address change */
>> + if (data == TPM_I2C_REG_I2C_DEV_ADDRESS) {
>> + qemu_log_mask(LOG_UNIMP, "%s: Device address change "
>> + "is not supported.\n", __func__);
>> + return 0xffffffff;
>> + }
>> + } else {
>> + trace_tpm_tis_i2c_send(data);
>> + }
>> +
>> + if (i2cst->offset < sizeof(i2cst->data)) {
>> + i2cst->operation = OP_SEND;
>> +
>> + /* Remember data locally for non-FIFO registers */
>> + if ((i2cst->offset == 0) ||
>> + (i2cst->data[0] != TPM_I2C_REG_DATA_FIFO)) {
>> + i2cst->data[i2cst->offset++] = data;
>> + } else {
>> + tpm_tis_write_data(&i2cst->state, i2cst->tis_addr, data,
>> 1);
>> + }
>> +
>> + return 0;
>> +
>> + } else {
>> + /* Return non-zero to indicate NAK */
>> + return 1;
>
> The 'else' is not needed. Just 'return 1'.
Done
>
>> + }
>> +}
>> +
>> +static Property tpm_tis_i2c_properties[] = {
>> + DEFINE_PROP_UINT32("irq", TPMStateI2C, state.irq_num, TPM_TIS_IRQ),
>> + DEFINE_PROP_TPMBE("tpmdev", TPMStateI2C, state.be_driver),
>> + DEFINE_PROP_END_OF_LIST(),
>> +};
>> +
>> +static void tpm_tis_i2c_realizefn(DeviceState *dev, Error **errp)
>> +{
>> + TPMStateI2C *i2cst = TPM_TIS_I2C(dev);
>> + TPMState *s = &i2cst->state;
>> +
>> + if (!tpm_find()) {
>> + error_setg(errp, "at most one TPM device is permitted");
>> + return;
>> + }
>> +
>> + /*
>> + * Get the backend pointer. It is not initialized propery during
>> + * device_class_set_props
>> + */
>> + s->be_driver = qemu_find_tpm_be("tpm0");
>> +
>> + if (!s->be_driver) {
>> + error_setg(errp, "'tpmdev' property is required");
>> + return;
>> + }
>> + if (s->irq_num > 15) {
>> + error_setg(errp, "IRQ %d is outside valid range of 0 to 15",
>> + s->irq_num);
>> + return;
>> + }
>> +}
>> +
>> +static void tpm_tis_i2c_reset(DeviceState *dev)
>> +{
>> + TPMStateI2C *i2cst = TPM_TIS_I2C(dev);
>> + TPMState *s = &i2cst->state;
>> +
>> + tpm_tis_i2c_clear_data(i2cst);
>> +
>> + i2cst->csum_enable = 0;
>> + i2cst->loc_sel = TPM_TIS_NO_LOCALITY;
>
>
> Per i2c spec 6.5.1 this has to be 0 by default.
Good catch. fixed.
>
>> +
>> + return tpm_tis_reset(s);
>> +}
>> +
>> +static void tpm_tis_i2c_class_init(ObjectClass *klass, void *data)
>> +{
>> + DeviceClass *dc = DEVICE_CLASS(klass);
>> + I2CSlaveClass *k = I2C_SLAVE_CLASS(klass);
>> + TPMIfClass *tc = TPM_IF_CLASS(klass);
>> +
>> + dc->realize = tpm_tis_i2c_realizefn;
>> + dc->reset = tpm_tis_i2c_reset;
>> + dc->vmsd = &vmstate_tpm_tis_i2c;
>> + device_class_set_props(dc, tpm_tis_i2c_properties);
>> +
>> + k->event = tpm_tis_i2c_event;
>> + k->recv = tpm_tis_i2c_recv;
>> + k->send = tpm_tis_i2c_send;
>> +
>> + tc->model = TPM_MODEL_TPM_TIS;
>> + tc->request_completed = tpm_tis_i2c_request_completed;
>> + tc->get_version = tpm_tis_i2c_get_tpm_version;
>
> isa and sysbus devices call this:
>
> set_bit(DEVICE_CATEGORY_MISC, dc->categories);
>
> The i2c should probably also have it.
Done.
>
>> +}
>> +
>> +static const TypeInfo tpm_tis_i2c_info = {
>> + .name = TYPE_TPM_TIS_I2C,
>> + .parent = TYPE_I2C_SLAVE,
>> + .instance_size = sizeof(TPMStateI2C),
>
> We will need an init function here to be able to call sysbus_init_irq()
>
> static void tpm_tis_i2c_initfn(Object *obj)
> {
> TPMStateI2C *i2cst = TPM_TIS_I2C(obj);
> TPMState *s = &i2cst->state;
>
> sysbus_init_irq(SYS_BUS_DEVICE(obj), &s->irq);
> }
>
> Without this, Linux will probably have to use the driver in polling
> mode. Maybe it will switch to interrupt mode once this is called.
>
> Due to the insights given in i2c spec table 11 I now have 3 patches on
> top of your v6:
> https://github.com/stefanberger/qemu-tpm/commits/tpm-i2c.v6
Added this function.
Thanks for the review.
Ninad
>
>
> Thanks!
>
> Regards,
> Stefan
>
>
>
>
>
>
>> + .class_init = tpm_tis_i2c_class_init,
>> + .interfaces = (InterfaceInfo[]) {
>> + { TYPE_TPM_IF },
>> + { }
>> + }
>> +};
>> +
>> +static void tpm_tis_i2c_register_types(void)
>> +{
>> + type_register_static(&tpm_tis_i2c_info);
>> +}
>> +
>> +type_init(tpm_tis_i2c_register_types)
>> diff --git a/hw/tpm/trace-events b/hw/tpm/trace-events
>> index f17110458e..fa882dfefe 100644
>> --- a/hw/tpm/trace-events
>> +++ b/hw/tpm/trace-events
>> @@ -36,3 +36,9 @@ tpm_spapr_do_crq_unknown_msg_type(uint8_t type)
>> "Unknown message type 0x%02x"
>> tpm_spapr_do_crq_unknown_crq(uint8_t raw1, uint8_t raw2) "unknown
>> CRQ 0x%02x 0x%02x ..."
>> tpm_spapr_post_load(void) "Delivering TPM response after resume"
>> tpm_spapr_caught_response(uint32_t v) "Caught response to deliver
>> after resume: %u bytes"
>> +
>> +# tpm_tis_i2c.c
>> +tpm_tis_i2c_recv(uint8_t data) "TPM I2C read: 0x%X"
>> +tpm_tis_i2c_send(uint8_t data) "TPM I2C write: 0x%X"
>> +tpm_tis_i2c_event(const char *event) "TPM I2C event: %s"
>> +tpm_tis_i2c_send_reg(const char *name, int reg) "TPM I2C write
>> register: %s(0x%X)"
>> diff --git a/include/sysemu/tpm.h b/include/sysemu/tpm.h
>> index fb40e30ff6..66e3b45f30 100644
>> --- a/include/sysemu/tpm.h
>> +++ b/include/sysemu/tpm.h
>> @@ -48,6 +48,7 @@ struct TPMIfClass {
>> #define TYPE_TPM_TIS_SYSBUS "tpm-tis-device"
>> #define TYPE_TPM_CRB "tpm-crb"
>> #define TYPE_TPM_SPAPR "tpm-spapr"
>> +#define TYPE_TPM_TIS_I2C "tpm-tis-i2c"
>> #define TPM_IS_TIS_ISA(chr) \
>> object_dynamic_cast(OBJECT(chr), TYPE_TPM_TIS_ISA)
>> @@ -57,6 +58,8 @@ struct TPMIfClass {
>> object_dynamic_cast(OBJECT(chr), TYPE_TPM_CRB)
>> #define TPM_IS_SPAPR(chr) \
>> object_dynamic_cast(OBJECT(chr), TYPE_TPM_SPAPR)
>> +#define TPM_IS_TIS_I2C(chr) \
>> + object_dynamic_cast(OBJECT(chr), TYPE_TPM_TIS_I2C)
>> /* returns NULL unless there is exactly one TPM device */
>> static inline TPMIf *tpm_find(void)
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2023-03-26 22:24 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2023-03-26 2:38 [PATCH v6 0/3] Add support for TPM devices over I2C bus Ninad Palsule
2023-03-26 2:38 ` [PATCH v6 1/3] docs: " Ninad Palsule
2023-03-26 2:38 ` [PATCH v6 2/3] tpm: Extend common APIs to support TPM TIS I2C Ninad Palsule
2023-03-26 2:38 ` [PATCH v6 3/3] tpm: Add support for TPM device over I2C bus Ninad Palsule
2023-03-26 13:00 ` Stefan Berger
2023-03-26 22:23 ` Ninad Palsule
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).