* [PATCH v7 1/3] hw/riscv: virt: Assume M-mode FW in pflash0 only when "-bios none"
2023-06-01 4:59 [PATCH v7 0/3] hw/riscv/virt: pflash improvements Sunil V L
@ 2023-06-01 4:59 ` Sunil V L
2023-06-01 4:59 ` [PATCH v7 2/3] riscv/virt: Support using pflash via -blockdev option Sunil V L
` (2 subsequent siblings)
3 siblings, 0 replies; 7+ messages in thread
From: Sunil V L @ 2023-06-01 4:59 UTC (permalink / raw)
To: qemu-riscv, qemu-devel
Cc: Palmer Dabbelt, Alistair Francis, Bin Meng, Weiwei Li,
Daniel Henrique Barboza, Liu Zhiwei, Andrea Bolognani, Sunil V L,
Heinrich Schuchardt
Currently, virt machine supports two pflash instances each with
32MB size. However, the first pflash is always assumed to
contain M-mode firmware and reset vector is set to this if
enabled. Hence, for S-mode payloads like EDK2, only one pflash
instance is available for use. This means both code and NV variables
of EDK2 will need to use the same pflash.
The OS distros keep the EDK2 FW code as readonly. When non-volatile
variables also need to share the same pflash, it is not possible
to keep it as readonly since variables need write access.
To resolve this issue, the code and NV variables need to be separated.
But in that case we need an extra flash. Hence, modify the convention
for non-KVM guests such that, pflash0 will contain the M-mode FW
only when "-bios none" option is used. Otherwise, pflash0 will contain
the S-mode payload FW. This enables both pflash instances available
for EDK2 use.
When KVM is enabled, pflash0 is always assumed to contain the
S-mode payload firmware only.
Example usage:
1) pflash0 containing M-mode FW
qemu-system-riscv64 -bios none -pflash <mmode_fw> -machine virt
or
qemu-system-riscv64 -bios none \
-drive file=<mmode_fw>,if=pflash,format=raw,unit=0 -machine virt
2) pflash0 containing S-mode payload like EDK2
qemu-system-riscv64 -pflash <smode_fw_code> -pflash <smode_vars> -machine virt
or
qemu-system-riscv64 -bios <opensbi_fw> \
-pflash <smode_fw_code> \
-pflash <smode_vars> \
-machine virt
or
qemu-system-riscv64 -bios <opensbi_fw> \
-drive file=<smode_fw_code>,if=pflash,format=raw,unit=0,readonly=on \
-drive file=<smode_fw_vars>,if=pflash,format=raw,unit=1 \
-machine virt
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
---
hw/riscv/virt.c | 53 ++++++++++++++++++++-----------------------------
1 file changed, 21 insertions(+), 32 deletions(-)
diff --git a/hw/riscv/virt.c b/hw/riscv/virt.c
index 4e3efbee16..3e5dc649c3 100644
--- a/hw/riscv/virt.c
+++ b/hw/riscv/virt.c
@@ -1245,7 +1245,7 @@ static void virt_machine_done(Notifier *notifier, void *data)
target_ulong firmware_end_addr, kernel_start_addr;
const char *firmware_name = riscv_default_firmware_name(&s->soc[0]);
uint32_t fdt_load_addr;
- uint64_t kernel_entry;
+ uint64_t kernel_entry = 0;
/*
* Only direct boot kernel is currently supported for KVM VM,
@@ -1266,42 +1266,31 @@ static void virt_machine_done(Notifier *notifier, void *data)
firmware_end_addr = riscv_find_and_load_firmware(machine, firmware_name,
start_addr, NULL);
- if (drive_get(IF_PFLASH, 0, 1)) {
- /*
- * S-mode FW like EDK2 will be kept in second plash (unit 1).
- * When both kernel, initrd and pflash options are provided in the
- * command line, the kernel and initrd will be copied to the fw_cfg
- * table and opensbi will jump to the flash address which is the
- * entry point of S-mode FW. It is the job of the S-mode FW to load
- * the kernel and initrd using fw_cfg table.
- *
- * If only pflash is given but not -kernel, then it is the job of
- * of the S-mode firmware to locate and load the kernel.
- * In either case, the next_addr for opensbi will be the flash address.
- */
- riscv_setup_firmware_boot(machine);
- kernel_entry = virt_memmap[VIRT_FLASH].base +
- virt_memmap[VIRT_FLASH].size / 2;
- } else if (machine->kernel_filename) {
+ if (drive_get(IF_PFLASH, 0, 0)) {
+ if (machine->firmware && !strcmp(machine->firmware, "none") &&
+ !kvm_enabled()) {
+ /*
+ * Pflash was supplied but bios is none and not KVM guest,
+ * let's overwrite the address we jump to after reset to
+ * the base of the flash.
+ */
+ start_addr = virt_memmap[VIRT_FLASH].base;
+ } else {
+ /*
+ * Pflash was supplied but either KVM guest or bios is not none.
+ * In this case, base of the flash would contain S-mode payload.
+ */
+ riscv_setup_firmware_boot(machine);
+ kernel_entry = virt_memmap[VIRT_FLASH].base;
+ }
+ }
+
+ if (machine->kernel_filename && !kernel_entry) {
kernel_start_addr = riscv_calc_kernel_start_addr(&s->soc[0],
firmware_end_addr);
kernel_entry = riscv_load_kernel(machine, &s->soc[0],
kernel_start_addr, true, NULL);
- } else {
- /*
- * If dynamic firmware is used, it doesn't know where is the next mode
- * if kernel argument is not set.
- */
- kernel_entry = 0;
- }
-
- if (drive_get(IF_PFLASH, 0, 0)) {
- /*
- * Pflash was supplied, let's overwrite the address we jump to after
- * reset to the base of the flash.
- */
- start_addr = virt_memmap[VIRT_FLASH].base;
}
fdt_load_addr = riscv_compute_fdt_addr(memmap[VIRT_DRAM].base,
--
2.34.1
^ permalink raw reply related [flat|nested] 7+ messages in thread* [PATCH v7 2/3] riscv/virt: Support using pflash via -blockdev option
2023-06-01 4:59 [PATCH v7 0/3] hw/riscv/virt: pflash improvements Sunil V L
2023-06-01 4:59 ` [PATCH v7 1/3] hw/riscv: virt: Assume M-mode FW in pflash0 only when "-bios none" Sunil V L
@ 2023-06-01 4:59 ` Sunil V L
2023-06-01 5:33 ` Alistair Francis
2023-06-01 4:59 ` [PATCH v7 3/3] docs/system: riscv: Add pflash usage details Sunil V L
2023-06-02 2:11 ` [PATCH v7 0/3] hw/riscv/virt: pflash improvements Alistair Francis
3 siblings, 1 reply; 7+ messages in thread
From: Sunil V L @ 2023-06-01 4:59 UTC (permalink / raw)
To: qemu-riscv, qemu-devel
Cc: Palmer Dabbelt, Alistair Francis, Bin Meng, Weiwei Li,
Daniel Henrique Barboza, Liu Zhiwei, Andrea Bolognani, Sunil V L,
Philippe Mathieu-Daudé
Currently, pflash devices can be configured only via -pflash
or -drive options. This is the legacy way and the
better way is to use -blockdev as in other architectures.
libvirt also has moved to use -blockdev method.
To support -blockdev option, pflash devices need to be
created in instance_init itself. So, update the code to
move the virt_flash_create() to instance_init. Also, use
standard interfaces to detect whether pflash0 is
configured or not.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reported-by: Andrea Bolognani <abologna@redhat.com>
Tested-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
---
hw/riscv/virt.c | 8 +++++---
1 file changed, 5 insertions(+), 3 deletions(-)
diff --git a/hw/riscv/virt.c b/hw/riscv/virt.c
index 3e5dc649c3..76c7a3ba3b 100644
--- a/hw/riscv/virt.c
+++ b/hw/riscv/virt.c
@@ -1246,6 +1246,7 @@ static void virt_machine_done(Notifier *notifier, void *data)
const char *firmware_name = riscv_default_firmware_name(&s->soc[0]);
uint32_t fdt_load_addr;
uint64_t kernel_entry = 0;
+ BlockBackend *pflash_blk0;
/*
* Only direct boot kernel is currently supported for KVM VM,
@@ -1266,7 +1267,8 @@ static void virt_machine_done(Notifier *notifier, void *data)
firmware_end_addr = riscv_find_and_load_firmware(machine, firmware_name,
start_addr, NULL);
- if (drive_get(IF_PFLASH, 0, 0)) {
+ pflash_blk0 = pflash_cfi01_get_blk(s->flash[0]);
+ if (pflash_blk0) {
if (machine->firmware && !strcmp(machine->firmware, "none") &&
!kvm_enabled()) {
/*
@@ -1499,8 +1501,6 @@ static void virt_machine_init(MachineState *machine)
sysbus_create_simple("goldfish_rtc", memmap[VIRT_RTC].base,
qdev_get_gpio_in(DEVICE(mmio_irqchip), RTC_IRQ));
- virt_flash_create(s);
-
for (i = 0; i < ARRAY_SIZE(s->flash); i++) {
/* Map legacy -drive if=pflash to machine properties */
pflash_cfi01_legacy_drive(s->flash[i],
@@ -1527,6 +1527,8 @@ static void virt_machine_instance_init(Object *obj)
{
RISCVVirtState *s = RISCV_VIRT_MACHINE(obj);
+ virt_flash_create(s);
+
s->oem_id = g_strndup(ACPI_BUILD_APPNAME6, 6);
s->oem_table_id = g_strndup(ACPI_BUILD_APPNAME8, 8);
s->acpi = ON_OFF_AUTO_AUTO;
--
2.34.1
^ permalink raw reply related [flat|nested] 7+ messages in thread* Re: [PATCH v7 2/3] riscv/virt: Support using pflash via -blockdev option
2023-06-01 4:59 ` [PATCH v7 2/3] riscv/virt: Support using pflash via -blockdev option Sunil V L
@ 2023-06-01 5:33 ` Alistair Francis
0 siblings, 0 replies; 7+ messages in thread
From: Alistair Francis @ 2023-06-01 5:33 UTC (permalink / raw)
To: Sunil V L
Cc: qemu-riscv, qemu-devel, Palmer Dabbelt, Alistair Francis,
Bin Meng, Weiwei Li, Daniel Henrique Barboza, Liu Zhiwei,
Andrea Bolognani, Philippe Mathieu-Daudé
On Thu, Jun 1, 2023 at 3:01 PM Sunil V L <sunilvl@ventanamicro.com> wrote:
>
> Currently, pflash devices can be configured only via -pflash
> or -drive options. This is the legacy way and the
> better way is to use -blockdev as in other architectures.
> libvirt also has moved to use -blockdev method.
>
> To support -blockdev option, pflash devices need to be
> created in instance_init itself. So, update the code to
> move the virt_flash_create() to instance_init. Also, use
> standard interfaces to detect whether pflash0 is
> configured or not.
>
> Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
> Reported-by: Andrea Bolognani <abologna@redhat.com>
> Tested-by: Andrea Bolognani <abologna@redhat.com>
> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Alistair
> ---
> hw/riscv/virt.c | 8 +++++---
> 1 file changed, 5 insertions(+), 3 deletions(-)
>
> diff --git a/hw/riscv/virt.c b/hw/riscv/virt.c
> index 3e5dc649c3..76c7a3ba3b 100644
> --- a/hw/riscv/virt.c
> +++ b/hw/riscv/virt.c
> @@ -1246,6 +1246,7 @@ static void virt_machine_done(Notifier *notifier, void *data)
> const char *firmware_name = riscv_default_firmware_name(&s->soc[0]);
> uint32_t fdt_load_addr;
> uint64_t kernel_entry = 0;
> + BlockBackend *pflash_blk0;
>
> /*
> * Only direct boot kernel is currently supported for KVM VM,
> @@ -1266,7 +1267,8 @@ static void virt_machine_done(Notifier *notifier, void *data)
> firmware_end_addr = riscv_find_and_load_firmware(machine, firmware_name,
> start_addr, NULL);
>
> - if (drive_get(IF_PFLASH, 0, 0)) {
> + pflash_blk0 = pflash_cfi01_get_blk(s->flash[0]);
> + if (pflash_blk0) {
> if (machine->firmware && !strcmp(machine->firmware, "none") &&
> !kvm_enabled()) {
> /*
> @@ -1499,8 +1501,6 @@ static void virt_machine_init(MachineState *machine)
> sysbus_create_simple("goldfish_rtc", memmap[VIRT_RTC].base,
> qdev_get_gpio_in(DEVICE(mmio_irqchip), RTC_IRQ));
>
> - virt_flash_create(s);
> -
> for (i = 0; i < ARRAY_SIZE(s->flash); i++) {
> /* Map legacy -drive if=pflash to machine properties */
> pflash_cfi01_legacy_drive(s->flash[i],
> @@ -1527,6 +1527,8 @@ static void virt_machine_instance_init(Object *obj)
> {
> RISCVVirtState *s = RISCV_VIRT_MACHINE(obj);
>
> + virt_flash_create(s);
> +
> s->oem_id = g_strndup(ACPI_BUILD_APPNAME6, 6);
> s->oem_table_id = g_strndup(ACPI_BUILD_APPNAME8, 8);
> s->acpi = ON_OFF_AUTO_AUTO;
> --
> 2.34.1
>
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH v7 3/3] docs/system: riscv: Add pflash usage details
2023-06-01 4:59 [PATCH v7 0/3] hw/riscv/virt: pflash improvements Sunil V L
2023-06-01 4:59 ` [PATCH v7 1/3] hw/riscv: virt: Assume M-mode FW in pflash0 only when "-bios none" Sunil V L
2023-06-01 4:59 ` [PATCH v7 2/3] riscv/virt: Support using pflash via -blockdev option Sunil V L
@ 2023-06-01 4:59 ` Sunil V L
2023-06-01 5:33 ` Alistair Francis
2023-06-02 2:11 ` [PATCH v7 0/3] hw/riscv/virt: pflash improvements Alistair Francis
3 siblings, 1 reply; 7+ messages in thread
From: Sunil V L @ 2023-06-01 4:59 UTC (permalink / raw)
To: qemu-riscv, qemu-devel
Cc: Palmer Dabbelt, Alistair Francis, Bin Meng, Weiwei Li,
Daniel Henrique Barboza, Liu Zhiwei, Andrea Bolognani, Sunil V L,
Philippe Mathieu-Daudé
pflash devices can be used in virt machine for different
purposes like for ROM code or S-mode FW payload. Add a
section in the documentation on how to use pflash devices
for different purposes.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
---
docs/system/riscv/virt.rst | 31 +++++++++++++++++++++++++++++++
1 file changed, 31 insertions(+)
diff --git a/docs/system/riscv/virt.rst b/docs/system/riscv/virt.rst
index 4b16e41d7f..b33f45e5b3 100644
--- a/docs/system/riscv/virt.rst
+++ b/docs/system/riscv/virt.rst
@@ -53,6 +53,37 @@ with the default OpenSBI firmware image as the -bios. It also supports
the recommended RISC-V bootflow: U-Boot SPL (M-mode) loads OpenSBI fw_dynamic
firmware and U-Boot proper (S-mode), using the standard -bios functionality.
+Using flash devices
+-------------------
+
+By default, the first flash device (pflash0) is expected to contain
+S-mode firmware code. It can be configured as read-only, with the
+second flash device (pflash1) available to store configuration data.
+
+For example, booting edk2 looks like
+
+.. code-block:: bash
+
+ $ qemu-system-riscv64 \
+ -blockdev node-name=pflash0,driver=file,read-only=on,filename=<edk2_code> \
+ -blockdev node-name=pflash1,driver=file,filename=<edk2_vars> \
+ -M virt,pflash0=pflash0,pflash1=pflash1 \
+ ... other args ....
+
+For TCG guests only, it is also possible to boot M-mode firmware from
+the first flash device (pflash0) by additionally passing ``-bios
+none``, as in
+
+.. code-block:: bash
+
+ $ qemu-system-riscv64 \
+ -bios none \
+ -blockdev node-name=pflash0,driver=file,read-only=on,filename=<m_mode_code> \
+ -M virt,pflash0=pflash0 \
+ ... other args ....
+
+Firmware images used for pflash must be exactly 32 MiB in size.
+
Machine-specific options
------------------------
--
2.34.1
^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH v7 3/3] docs/system: riscv: Add pflash usage details
2023-06-01 4:59 ` [PATCH v7 3/3] docs/system: riscv: Add pflash usage details Sunil V L
@ 2023-06-01 5:33 ` Alistair Francis
0 siblings, 0 replies; 7+ messages in thread
From: Alistair Francis @ 2023-06-01 5:33 UTC (permalink / raw)
To: Sunil V L
Cc: qemu-riscv, qemu-devel, Palmer Dabbelt, Alistair Francis,
Bin Meng, Weiwei Li, Daniel Henrique Barboza, Liu Zhiwei,
Andrea Bolognani, Philippe Mathieu-Daudé
On Thu, Jun 1, 2023 at 3:01 PM Sunil V L <sunilvl@ventanamicro.com> wrote:
>
> pflash devices can be used in virt machine for different
> purposes like for ROM code or S-mode FW payload. Add a
> section in the documentation on how to use pflash devices
> for different purposes.
>
> Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Alistair
> ---
> docs/system/riscv/virt.rst | 31 +++++++++++++++++++++++++++++++
> 1 file changed, 31 insertions(+)
>
> diff --git a/docs/system/riscv/virt.rst b/docs/system/riscv/virt.rst
> index 4b16e41d7f..b33f45e5b3 100644
> --- a/docs/system/riscv/virt.rst
> +++ b/docs/system/riscv/virt.rst
> @@ -53,6 +53,37 @@ with the default OpenSBI firmware image as the -bios. It also supports
> the recommended RISC-V bootflow: U-Boot SPL (M-mode) loads OpenSBI fw_dynamic
> firmware and U-Boot proper (S-mode), using the standard -bios functionality.
>
> +Using flash devices
> +-------------------
> +
> +By default, the first flash device (pflash0) is expected to contain
> +S-mode firmware code. It can be configured as read-only, with the
> +second flash device (pflash1) available to store configuration data.
> +
> +For example, booting edk2 looks like
> +
> +.. code-block:: bash
> +
> + $ qemu-system-riscv64 \
> + -blockdev node-name=pflash0,driver=file,read-only=on,filename=<edk2_code> \
> + -blockdev node-name=pflash1,driver=file,filename=<edk2_vars> \
> + -M virt,pflash0=pflash0,pflash1=pflash1 \
> + ... other args ....
> +
> +For TCG guests only, it is also possible to boot M-mode firmware from
> +the first flash device (pflash0) by additionally passing ``-bios
> +none``, as in
> +
> +.. code-block:: bash
> +
> + $ qemu-system-riscv64 \
> + -bios none \
> + -blockdev node-name=pflash0,driver=file,read-only=on,filename=<m_mode_code> \
> + -M virt,pflash0=pflash0 \
> + ... other args ....
> +
> +Firmware images used for pflash must be exactly 32 MiB in size.
> +
> Machine-specific options
> ------------------------
>
> --
> 2.34.1
>
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v7 0/3] hw/riscv/virt: pflash improvements
2023-06-01 4:59 [PATCH v7 0/3] hw/riscv/virt: pflash improvements Sunil V L
` (2 preceding siblings ...)
2023-06-01 4:59 ` [PATCH v7 3/3] docs/system: riscv: Add pflash usage details Sunil V L
@ 2023-06-02 2:11 ` Alistair Francis
3 siblings, 0 replies; 7+ messages in thread
From: Alistair Francis @ 2023-06-02 2:11 UTC (permalink / raw)
To: Sunil V L
Cc: qemu-riscv, qemu-devel, Palmer Dabbelt, Alistair Francis,
Bin Meng, Weiwei Li, Daniel Henrique Barboza, Liu Zhiwei,
Andrea Bolognani
On Thu, Jun 1, 2023 at 3:00 PM Sunil V L <sunilvl@ventanamicro.com> wrote:
>
> This series improves the pflash usage in RISC-V virt machine with solutions to
> below issues.
>
> 1) Currently the first pflash is reserved for ROM/M-mode firmware code. But S-mode
> payload firmware like EDK2 need both pflash devices to have separate code and variable
> store so that OS distros can keep the FW code as read-only.
>
> The issue is reported at
> https://salsa.debian.org/qemu-team/edk2/-/commit/c345655a0149f64c5020bfc1e53c619ce60587f6
>
> 2) The latest way of using pflash devices in other architectures and libvirt
> is by using -blockdev and machine options. However, currently this method is
> not working in RISC-V.
>
> With above issues fixed, added documentation on how to use pflash devices
> in RISC-V virt machine.
>
> This patch series is based on Alistair's riscv-to-apply.next branch.
>
> Changes since v6:
> 1) Updated the documentation patch as per text provided by Andrea.
>
> Changes since v5:
> 1) Added KVM use case as per feedback from Anup. Updated the documentation
> patch that only S-mode payload is supported for KVM guests. Tested with
> KVM enabled.
> 2) Updated tags.
>
> Changes since v4:
> 1) Updated patch 2 to avoid accessing private field as per feedback from Philippe.
> 2) Updated documentation patch to add read-only for ROM usage.
> 3) Rebased to latest riscv-to-apply.next branch and updated tags.
>
> Changes since v3:
> 1) Converted single patch to a series with a cover letter since there are
> multiple patches now.
> 2) Added a new patch to enable pflash usage via -blockdev option.
> 3) Separated the documentation change into new patch and updated the
> documentation to mention only -blockdev option which seems to be the
> recommended way of using pflash.
>
> Changes since v2:
> 1) Reverted v2 changes and used v1 approach so that pflash0 can be used
> for code and pflash1 for variable store.
> 2) Rebased to latest riscv-to-apply.next branch.
> 3) Added documentation for pflash usage.
>
> Changes since v1:
> 1) Simplified the fix such that it doesn't break current EDK2.
>
> Sunil V L (3):
> hw/riscv: virt: Assume M-mode FW in pflash0 only when "-bios none"
> riscv/virt: Support using pflash via -blockdev option
> docs/system: riscv: Add pflash usage details
Thanks!
Applied to riscv-to-apply.next
Alistair
>
> docs/system/riscv/virt.rst | 31 ++++++++++++++++++++
> hw/riscv/virt.c | 59 ++++++++++++++++----------------------
> 2 files changed, 56 insertions(+), 34 deletions(-)
>
> --
> 2.34.1
>
>
^ permalink raw reply [flat|nested] 7+ messages in thread