[PATCH v3 5/5] ARM: dts: at91: at91-sama5d27_som1_ek: Add sama5d27 SoM1 EK support

[Claudiu Beznea <claudiu.beznea@microchip.com>]

Add specifig DTS files and bindings for sama5d27 SoM1 EK board.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
---
 arch/arm/boot/dts/Makefile                  |   1 +
 arch/arm/boot/dts/at91-sama5d27_som1_ek.dts | 537 ++++++++++++++++++++++++++++
 2 files changed, 538 insertions(+)
 create mode 100644 arch/arm/boot/dts/at91-sama5d27_som1_ek.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9449493..3396f73 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -46,6 +46,7 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
 	at91sam9x35ek.dtb
 dtb-$(CONFIG_SOC_SAM_V7) += \
 	at91-kizbox2.dtb \
+	at91-sama5d27_som1_ek.dtb \
 	at91-sama5d2_xplained.dtb \
 	at91-sama5d3_xplained.dtb \
 	at91-tse850-3.dtb \
diff --git a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts b/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
new file mode 100644
index 0000000..9c9088c
--- /dev/null
+++ b/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
@@ -0,0 +1,537 @@
+/*
+ * at91-sama5d27_som1_ek.dts - Device Tree file for SAMA5D27-SOM1-EK board
+ *
+ *  Copyright (c) 2017, Microchip Technology Inc.
+ *                2016 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *                2017 Cristian Birsan <cristian.birsan@microchip.com>
+ *                2017 Claudiu Beznea <claudiu.beznea@microchip.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+#include "at91-sama5d27_som1.dtsi"
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Atmel SAMA5D27 SOM1 EK";
+	compatible = "atmel,sama5d27-som1-ek", "atmel,sama5d27-som1", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	ahb {
+		usb0: gadget@00300000 {
+			atmel,vbus-gpio = <&pioA PIN_PD20 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usba_vbus>;
+			status = "okay";
+		};
+
+		usb1: ohci@00400000 {
+			num-ports = <3>;
+			atmel,vbus-gpio = <&pioA PIN_PA10 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb_default>;
+			status = "okay";
+		};
+
+		usb2: ehci@00500000 {
+			status = "okay";
+		};
+
+		sdmmc0: sdio-host@a0000000 {
+			bus-width = <8>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sdmmc0_default>;
+			status = "okay";
+		};
+
+		sdmmc1: sdio-host@b0000000 {
+			bus-width = <4>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sdmmc1_default>;
+			status = "okay";
+		};
+
+		apb {
+			isc: isc@f0008000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_isc_base &pinctrl_isc_data_8bit &pinctrl_isc_data_9_10 &pinctrl_isc_data_11_12>;
+				status = "okay";
+			};
+
+			spi0: spi@f8000000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_spi0_default>;
+				status = "okay";
+			};
+
+			macb0: ethernet@f8008000 {
+				status = "okay";
+			};
+
+			uart1: serial@f8020000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart1_default>;
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				status = "okay";
+			};
+
+			uart2: serial@f8024000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_mikrobus2_uart>;
+				atmel,use-dma-rx;
+				atmel-use-dma-tx;
+				status = "okay";
+			};
+
+			pwm0: pwm@f802c000 {
+				status = "okay";
+			};
+
+			flx1: flexcom@f8038000 {
+				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+				status = "disabled";
+
+				i2c2: i2c@600 {
+					compatible = "atmel,sama5d2-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <20 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <0>, <0>;
+					dma-names = "tx", "rx";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&flx1_clk>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_mikrobus_i2c>;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			shdwc@f8048010 {
+				atmel,shdwc-debouncer = <976>;
+				atmel,wakeup-rtc-timer;
+
+				input@0 {
+					reg = <0>;
+					atmel,wakeup-type = "low";
+				};
+			};
+
+			watchdog@f8048040 {
+				status = "okay";
+			};
+
+			can0: can@f8054000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_can0_default>;
+			};
+
+			uart3: serial@fc008000 {
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart3_default>;
+				status = "disabled";
+			};
+
+			uart4: serial@fc00c000 {
+				atmel,use-dma-rx;
+				atmel,use-dma-tx;
+				pinctrl-name = "default";
+				pinctrl-0 = <&pinctrl_mikrobus1_uart>;
+				status = "okay";
+			};
+
+			flx3: flexcom@fc014000 {
+				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+				status = "disabled";
+
+				uart7: serial@200 {
+					compatible = "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&flx3_clk>;
+					clock-names = "usart";
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_flx3_default>;
+					atmel,fifo-size = <32>;
+					status = "disabled";
+				};
+
+				spi2: spi@400 {
+					compatible = "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&flx3_clk>;
+					clock-names = "spi_clk";
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_flx3_default>;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx4: flexcom@fc018000 {
+				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+				status = "okay";
+
+				uart6: serial@200 {
+					compatible = "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&flx4_clk>;
+					clock-names = "usart";
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_flx4_default>;
+					atmel,fifo-size = <32>;
+					status = "disabled";
+				};
+
+				spi3: spi@400 {
+					compatible = "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&flx4_clk>;
+					clock-names = "spi_clk";
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_mikrobus_spi &pinctrl_mikrobus1_spi_cs &pinctrl_mikrobus2_spi_cs>;
+					atmel,fifo-size = <16>;
+					status = "okay";
+				};
+
+				i2c3: i2c@600 {
+					compatible = "atmel,sama5d2-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <0>, <0>;
+					dma-names = "tx", "rx";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&flx4_clk>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_flx4_default>;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			i2c1: i2c@fc028000 {
+				dmas = <0>, <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c1_default>;
+				status = "okay";
+			};
+
+			pinctrl@fc038000 {
+
+				pinctrl_can0_default: can0_default {
+					pinmux = <PIN_PC10__CANTX0>,
+						 <PIN_PC11__CANRX0>;
+					bias-disable;
+				};
+
+				pinctrl_can1_default: can1_default {
+					pinmux = <PIN_PC26__CANTX1>,
+						 <PIN_PC27__CANRX1>;
+					bias-disable;
+				};
+
+				pinctrl_flx3_default: flx3_default {
+					pinmux = <PIN_PC20__FLEXCOM3_IO0>,
+						 <PIN_PC19__FLEXCOM3_IO1>,
+						 <PIN_PC18__FLEXCOM3_IO2>,
+						 <PIN_PC21__FLEXCOM3_IO3>,
+						 <PIN_PC22__FLEXCOM3_IO4>;
+					bias-disable;
+				};
+
+				pinctrl_i2c1_default: i2c1_default {
+					pinmux = <PIN_PD4__TWD1>,
+						 <PIN_PD5__TWCK1>;
+					bias-disable;
+				};
+
+				pinctrl_isc_base: isc_base {
+					pinmux = <PIN_PC21__ISC_PCK>,
+						 <PIN_PC22__ISC_VSYNC>,
+						 <PIN_PC23__ISC_HSYNC>,
+						 <PIN_PC24__ISC_MCK>;
+					bias-disable;
+				};
+
+				pinctrl_isc_data_8bit: isc_data_8bit {
+					pinmux = <PIN_PC20__ISC_D11>,
+						 <PIN_PC19__ISC_D10>,
+						 <PIN_PC18__ISC_D9>,
+						 <PIN_PC17__ISC_D8>,
+						 <PIN_PC16__ISC_D7>,
+						 <PIN_PC15__ISC_D6>,
+						 <PIN_PC14__ISC_D5>,
+						 <PIN_PC13__ISC_D4>;
+					bias-disable;
+				};
+
+				pinctrl_isc_data_9_10: isc_data_9_10 {
+					pinmux = <PIN_PC12__ISC_D3>,
+						 <PIN_PC11__ISC_D2>;
+					bias-disable;
+				};
+
+				pinctrl_isc_data_11_12: isc_data_11_12 {
+					pinmux = <PIN_PC10__ISC_D1>,
+						 <PIN_PC9__ISC_D0>;
+					bias-disable;
+				};
+
+				pinctrl_key_gpio_default: key_gpio_default {
+					pinmux = <PIN_PA29__GPIO>;
+					bias-pull-up;
+				};
+
+				pinctrl_led_gpio_default: led_gpio_default {
+					pinmux = <PIN_PA27__GPIO>,
+						 <PIN_PB1__GPIO>,
+						 <PIN_PA31__GPIO>;
+					bias-pull-up;
+				};
+
+				pinctrl_sdmmc0_default: sdmmc0_default {
+					cmd_data {
+						pinmux = <PIN_PA1__SDMMC0_CMD>,
+							 <PIN_PA2__SDMMC0_DAT0>,
+							 <PIN_PA3__SDMMC0_DAT1>,
+							 <PIN_PA4__SDMMC0_DAT2>,
+							 <PIN_PA5__SDMMC0_DAT3>,
+							 <PIN_PA6__SDMMC0_DAT4>,
+							 <PIN_PA7__SDMMC0_DAT5>,
+							 <PIN_PA8__SDMMC0_DAT6>,
+							 <PIN_PA9__SDMMC0_DAT7>;
+						bias-pull-up;
+					};
+
+					ck_cd_vddsel {
+						pinmux = <PIN_PA0__SDMMC0_CK>,
+							 <PIN_PA11__SDMMC0_VDDSEL>,
+							 <PIN_PA13__SDMMC0_CD>;
+						bias-disable;
+					};
+				};
+
+				pinctrl_sdmmc1_default: sdmmc1_default {
+					cmd_data {
+						pinmux = <PIN_PA28__SDMMC1_CMD>,
+							 <PIN_PA18__SDMMC1_DAT0>,
+							 <PIN_PA19__SDMMC1_DAT1>,
+							 <PIN_PA20__SDMMC1_DAT2>,
+							 <PIN_PA21__SDMMC1_DAT3>;
+						bias-pull-up;
+					};
+
+					conf-ck_cd {
+						pinmux = <PIN_PA22__SDMMC1_CK>,
+							 <PIN_PA30__SDMMC1_CD>;
+						bias-disable;
+					};
+				};
+
+				pinctrl_spi0_default: spi0_default {
+					pinmux = <PIN_PA14__SPI0_SPCK>,
+						 <PIN_PA15__SPI0_MOSI>,
+						 <PIN_PA16__SPI0_MISO>,
+						 <PIN_PA17__SPI0_NPCS0>;
+					bias-disable;
+				};
+
+				pinctrl_uart1_default: uart1_default {
+					pinmux = <PIN_PD2__URXD1>,
+						 <PIN_PD3__UTXD1>;
+					bias-disable;
+				};
+
+				pinctrl_uart3_default: uart3_default {
+					pinmux = <PIN_PC12__URXD3>,
+						 <PIN_PC13__UTXD3>;
+					bias-disable;
+				};
+
+				pinctrl_usb_default: usb_default {
+					pinmux = <PIN_PA10__GPIO>,
+						 <PIN_PD19__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_usba_vbus: usba_vbus {
+					pinmux = <PIN_PD20__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_mikrobus1_an: mikrobus1_an {
+					pinmux = <PIN_PD25__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_mikrobus2_an: mikrobus2_an {
+					pinmux = <PIN_PD26__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_mikrobus1_rst: mikrobus1_rst {
+					pinmux = <PIN_PB2__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_mikrobus2_rst: mikrobus2_rst {
+					pinmux = <PIN_PA26__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_mikrobus1_spi_cs: mikrobus1_spi_cs {
+					pinmux = <PIN_PD0__FLEXCOM4_IO4>;
+					bias-disable;
+				};
+
+				pinctrl_mikrobus2_spi_cs: mikrobus2_spi_cs {
+					pinmux = <PIN_PC31__FLEXCOM4_IO3>;
+					bias-disable;
+				};
+
+				pinctrl_mikrobus_spi: mikrobus_spi {
+					pinmux = <PIN_PC28__FLEXCOM4_IO0>,
+						 <PIN_PC29__FLEXCOM4_IO1>,
+						 <PIN_PC30__FLEXCOM4_IO2>;
+					bias-disable;
+				};
+
+				pinctrl_mikrobus1_pwm: mikrobus1_pwm {
+					pinmux = <PIN_PB1__PWML1>;
+					bias-disable;
+				};
+
+				pinctrl_mikrobus2_pwm: mikrobus2_pwm {
+					pinmux = <PIN_PA31__PWML0>;
+					bias-disable;
+				};
+
+				pinctrl_mikrobus1_int: mikrobus1_int {
+					pinmux = <PIN_PB0__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_mikrobus2_int: mikrobus2_int {
+					pinmux = <PIN_PA25__GPIO>;
+					bias-disable;
+				};
+
+				pinctrl_mikrobus1_uart: mikrobus1_uart {
+					pinmux = <PIN_PB3__URXD4>,
+						 <PIN_PB4__UTXD4>;
+					bias-disable;
+				};
+
+				pinctrl_mikrobus2_uart: mikrobus2_uart {
+					pinmux = <PIN_PD23__URXD2>,
+						 <PIN_PD24__UTXD2>;
+					bias-disable;
+				};
+
+				pinctrl_mikrobus_i2c: mikrobus1_i2c {
+					pinmux = <PIN_PA24__FLEXCOM1_IO0>,
+						 <PIN_PA23__FLEXCOM1_IO1>;
+					bias-disable;
+				};
+
+				pinctrl_flx4_default: flx4_uart_default {
+					pinmux = <PIN_PC28__FLEXCOM4_IO0>,
+						 <PIN_PC29__FLEXCOM4_IO1>,
+						 <PIN_PC30__FLEXCOM4_IO2>,
+						 <PIN_PC31__FLEXCOM4_IO3>,
+						 <PIN_PD0__FLEXCOM4_IO4>;
+					bias-disable;
+				};
+			};
+
+			can1: can@fc050000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_can1_default>;
+				status = "okay";
+			};
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+		pb4 {
+			label = "USER";
+			gpios = <&pioA PIN_PA29 GPIO_ACTIVE_LOW>;
+			linux,code = <0x104>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_led_gpio_default>;
+		status = "okay";
+
+		red {
+			label = "red";
+			gpios = <&pioA PIN_PA27 GPIO_ACTIVE_LOW>;
+		};
+
+		green {
+			label = "green";
+			gpios = <&pioA PIN_PB1 GPIO_ACTIVE_LOW>;
+		};
+
+		blue {
+			label = "blue";
+			gpios = <&pioA PIN_PA31 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
-- 
2.7.4