From: Marcin Wojtas <mw@semihalf.com> To: linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org Cc: andrew@lunn.ch, thomas.petazzoni@free-electrons.com, gregory.clement@free-electrons.com, mark.rutland@arm.com, marc.zyngier@arm.com, nadavh@marvell.com, neta@marvell.com, mw@semihalf.com, jaz@semihalf.com, hannah@marvell.com, zbodek@gmail.com Subject: [PATCH] ARM64: dts: marvell: armada-37xx: Enable uSD on ESPRESSObin Date: Fri, 21 Jul 2017 01:50:36 +0200 [thread overview] Message-ID: <1500594636-19911-1-git-send-email-mw@semihalf.com> (raw) The ESPRESSObin board exposes one of the SDHCI interfaces via J1 uSD slot. This patch enables it. Signed-off-by: Marcin Wojtas <mw@semihalf.com> Signed-off-by: Zbigniew Bodek <zbodek@gmail.com> --- .../boot/dts/marvell/armada-3720-espressobin.dts | 26 ++++++++++++++++++++++ 1 file changed, 26 insertions(+) diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts index b1af3f98..6d0caf1 100644 --- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts +++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts @@ -45,6 +45,7 @@ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> #include "armada-372x.dtsi" / { @@ -59,6 +60,20 @@ device_type = "memory"; reg = <0x00000000 0x00000000 0x00000000 0x20000000>; }; + + vcc_sd_reg1: regulator { + compatible = "regulator-gpio"; + regulator-name = "vcc_sd1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + + gpios = <&gpionb 4 GPIO_ACTIVE_HIGH>; + gpios-states = <0>; + states = <1800000 0x1 + 3300000 0x0>; + enable-active-high; + }; }; /* J9 */ @@ -71,6 +86,17 @@ status = "okay"; }; +/* J1 */ +&sdhci1 { + wp-inverted; + bus-width = <4>; + cd-gpios = <&gpionb 3 GPIO_ACTIVE_LOW>; + no-1-8-v; + marvell,pad-type = "sd"; + vqmmc-supply = <&vcc_sd_reg1>; + status = "okay"; +}; + /* Exported on the micro USB connector J5 through an FTDI */ &uart0 { status = "okay"; -- 1.8.3.1
WARNING: multiple messages have this Message-ID (diff)
From: mw@semihalf.com (Marcin Wojtas) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH] ARM64: dts: marvell: armada-37xx: Enable uSD on ESPRESSObin Date: Fri, 21 Jul 2017 01:50:36 +0200 [thread overview] Message-ID: <1500594636-19911-1-git-send-email-mw@semihalf.com> (raw) The ESPRESSObin board exposes one of the SDHCI interfaces via J1 uSD slot. This patch enables it. Signed-off-by: Marcin Wojtas <mw@semihalf.com> Signed-off-by: Zbigniew Bodek <zbodek@gmail.com> --- .../boot/dts/marvell/armada-3720-espressobin.dts | 26 ++++++++++++++++++++++ 1 file changed, 26 insertions(+) diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts index b1af3f98..6d0caf1 100644 --- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts +++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts @@ -45,6 +45,7 @@ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> #include "armada-372x.dtsi" / { @@ -59,6 +60,20 @@ device_type = "memory"; reg = <0x00000000 0x00000000 0x00000000 0x20000000>; }; + + vcc_sd_reg1: regulator { + compatible = "regulator-gpio"; + regulator-name = "vcc_sd1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + + gpios = <&gpionb 4 GPIO_ACTIVE_HIGH>; + gpios-states = <0>; + states = <1800000 0x1 + 3300000 0x0>; + enable-active-high; + }; }; /* J9 */ @@ -71,6 +86,17 @@ status = "okay"; }; +/* J1 */ +&sdhci1 { + wp-inverted; + bus-width = <4>; + cd-gpios = <&gpionb 3 GPIO_ACTIVE_LOW>; + no-1-8-v; + marvell,pad-type = "sd"; + vqmmc-supply = <&vcc_sd_reg1>; + status = "okay"; +}; + /* Exported on the micro USB connector J5 through an FTDI */ &uart0 { status = "okay"; -- 1.8.3.1
next reply other threads:[~2017-07-20 23:50 UTC|newest] Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top 2017-07-20 23:50 Marcin Wojtas [this message] 2017-07-20 23:50 ` [PATCH] ARM64: dts: marvell: armada-37xx: Enable uSD on ESPRESSObin Marcin Wojtas 2017-08-02 17:16 ` Miquel RAYNAL 2017-08-02 17:16 ` Miquel RAYNAL 2017-08-03 12:23 ` Gregory CLEMENT 2017-08-03 12:23 ` Gregory CLEMENT
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1500594636-19911-1-git-send-email-mw@semihalf.com \ --to=mw@semihalf.com \ --cc=andrew@lunn.ch \ --cc=gregory.clement@free-electrons.com \ --cc=hannah@marvell.com \ --cc=jaz@semihalf.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=marc.zyngier@arm.com \ --cc=mark.rutland@arm.com \ --cc=nadavh@marvell.com \ --cc=neta@marvell.com \ --cc=thomas.petazzoni@free-electrons.com \ --cc=zbodek@gmail.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.