From: Claudiu Beznea <claudiu.beznea@microchip.com>
To: <linux@armlinux.org.uk>, <nicolas.ferre@microchip.com>,
<alexandre.belloni@bootlin.com>,
<ludovic.desroches@microchip.com>, <sre@kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <linux-pm@vger.kernel.org>,
Claudiu Beznea <claudiu.beznea@microchip.com>,
Tudor Ambarus <tudor.ambarus@microchip.com>,
Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Subject: [PATCH v3 9/9] ARM: at91/defconfig: enable config flags for sam9x60 SoC
Date: Fri, 29 Nov 2019 15:51:45 +0200 [thread overview]
Message-ID: <1575035505-6310-10-git-send-email-claudiu.beznea@microchip.com> (raw)
In-Reply-To: <1575035505-6310-1-git-send-email-claudiu.beznea@microchip.com>
Enable config flags for SAM9X60 SoC. This includes SoC flag
(CONFIG_SOC_SAM9X60) and IP/board specific flags as follows:
- atmel maxtouch
- flexcom
- XDMA
- I2S Multi-channel
- mikroelectronica proto board
- SAMA5D2's ADC
- atmel QSPI
- classd
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
---
arch/arm/configs/at91_dt_defconfig | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/arch/arm/configs/at91_dt_defconfig b/arch/arm/configs/at91_dt_defconfig
index 148f753de6c7..5c5df8bc0074 100644
--- a/arch/arm/configs/at91_dt_defconfig
+++ b/arch/arm/configs/at91_dt_defconfig
@@ -13,6 +13,7 @@ CONFIG_ARCH_MULTI_V5=y
CONFIG_ARCH_AT91=y
CONFIG_SOC_AT91RM9200=y
CONFIG_SOC_AT91SAM9=y
+CONFIG_SOC_SAM9X60=y
# CONFIG_ATMEL_CLOCKSOURCE_PIT is not set
CONFIG_AEABI=y
CONFIG_UACCESS_WITH_MEMCPY=y
@@ -49,6 +50,7 @@ CONFIG_MTD_BLOCK=y
CONFIG_MTD_DATAFLASH=y
CONFIG_MTD_RAW_NAND=y
CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_SPI_NOR=y
CONFIG_MTD_UBI=y
CONFIG_MTD_UBI_GLUEBI=y
CONFIG_BLK_DEV_LOOP=y
@@ -99,6 +101,7 @@ CONFIG_KEYBOARD_GPIO=y
# CONFIG_INPUT_MOUSE is not set
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_ADS7846=y
+CONFIG_TOUCHSCREEN_ATMEL_MXT=y
# CONFIG_SERIO is not set
CONFIG_LEGACY_PTY_COUNT=4
CONFIG_SERIAL_ATMEL=y
@@ -108,11 +111,14 @@ CONFIG_I2C_AT91=y
CONFIG_I2C_GPIO=y
CONFIG_SPI=y
CONFIG_SPI_ATMEL=y
+CONFIG_SPI_ATMEL_QUADSPI=y
CONFIG_POWER_RESET=y
+# CONFIG_POWER_RESET_AT91_SAMA5D2_SHDWC is not set
CONFIG_POWER_SUPPLY=y
# CONFIG_HWMON is not set
CONFIG_WATCHDOG=y
CONFIG_AT91SAM9X_WATCHDOG=y
+CONFIG_MFD_ATMEL_FLEXCOM=y
CONFIG_MFD_ATMEL_HLCDC=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
@@ -136,6 +142,9 @@ CONFIG_SND_ATMEL_SOC=y
CONFIG_SND_AT91_SOC_SAM9G20_WM8731=y
CONFIG_SND_ATMEL_SOC_WM8904=y
CONFIG_SND_AT91_SOC_SAM9X5_WM8731=y
+CONFIG_SND_ATMEL_SOC_CLASSD=y
+CONFIG_SND_SOC_MIKROE_PROTO=m
+CONFIG_SND_MCHP_SOC_I2S_MCC=y
CONFIG_USB=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
CONFIG_USB_EHCI_HCD=y
@@ -167,9 +176,11 @@ CONFIG_RTC_DRV_AT91RM9200=y
CONFIG_RTC_DRV_AT91SAM9=y
CONFIG_DMADEVICES=y
CONFIG_AT_HDMAC=y
+CONFIG_AT_XDMAC=y
# CONFIG_IOMMU_SUPPORT is not set
CONFIG_IIO=y
CONFIG_AT91_ADC=y
+CONFIG_AT91_SAMA5D2_ADC=y
CONFIG_PWM=y
CONFIG_PWM_ATMEL=y
CONFIG_PWM_ATMEL_HLCDC_PWM=y
--
2.7.4
WARNING: multiple messages have this Message-ID (diff)
From: Claudiu Beznea <claudiu.beznea@microchip.com>
To: <linux@armlinux.org.uk>, <nicolas.ferre@microchip.com>,
<alexandre.belloni@bootlin.com>,
<ludovic.desroches@microchip.com>, <sre@kernel.org>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>,
linux-pm@vger.kernel.org, linux-kernel@vger.kernel.org,
Codrin Ciubotariu <codrin.ciubotariu@microchip.com>,
Claudiu Beznea <claudiu.beznea@microchip.com>,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH v3 9/9] ARM: at91/defconfig: enable config flags for sam9x60 SoC
Date: Fri, 29 Nov 2019 15:51:45 +0200 [thread overview]
Message-ID: <1575035505-6310-10-git-send-email-claudiu.beznea@microchip.com> (raw)
In-Reply-To: <1575035505-6310-1-git-send-email-claudiu.beznea@microchip.com>
Enable config flags for SAM9X60 SoC. This includes SoC flag
(CONFIG_SOC_SAM9X60) and IP/board specific flags as follows:
- atmel maxtouch
- flexcom
- XDMA
- I2S Multi-channel
- mikroelectronica proto board
- SAMA5D2's ADC
- atmel QSPI
- classd
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
---
arch/arm/configs/at91_dt_defconfig | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/arch/arm/configs/at91_dt_defconfig b/arch/arm/configs/at91_dt_defconfig
index 148f753de6c7..5c5df8bc0074 100644
--- a/arch/arm/configs/at91_dt_defconfig
+++ b/arch/arm/configs/at91_dt_defconfig
@@ -13,6 +13,7 @@ CONFIG_ARCH_MULTI_V5=y
CONFIG_ARCH_AT91=y
CONFIG_SOC_AT91RM9200=y
CONFIG_SOC_AT91SAM9=y
+CONFIG_SOC_SAM9X60=y
# CONFIG_ATMEL_CLOCKSOURCE_PIT is not set
CONFIG_AEABI=y
CONFIG_UACCESS_WITH_MEMCPY=y
@@ -49,6 +50,7 @@ CONFIG_MTD_BLOCK=y
CONFIG_MTD_DATAFLASH=y
CONFIG_MTD_RAW_NAND=y
CONFIG_MTD_NAND_ATMEL=y
+CONFIG_MTD_SPI_NOR=y
CONFIG_MTD_UBI=y
CONFIG_MTD_UBI_GLUEBI=y
CONFIG_BLK_DEV_LOOP=y
@@ -99,6 +101,7 @@ CONFIG_KEYBOARD_GPIO=y
# CONFIG_INPUT_MOUSE is not set
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_ADS7846=y
+CONFIG_TOUCHSCREEN_ATMEL_MXT=y
# CONFIG_SERIO is not set
CONFIG_LEGACY_PTY_COUNT=4
CONFIG_SERIAL_ATMEL=y
@@ -108,11 +111,14 @@ CONFIG_I2C_AT91=y
CONFIG_I2C_GPIO=y
CONFIG_SPI=y
CONFIG_SPI_ATMEL=y
+CONFIG_SPI_ATMEL_QUADSPI=y
CONFIG_POWER_RESET=y
+# CONFIG_POWER_RESET_AT91_SAMA5D2_SHDWC is not set
CONFIG_POWER_SUPPLY=y
# CONFIG_HWMON is not set
CONFIG_WATCHDOG=y
CONFIG_AT91SAM9X_WATCHDOG=y
+CONFIG_MFD_ATMEL_FLEXCOM=y
CONFIG_MFD_ATMEL_HLCDC=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
@@ -136,6 +142,9 @@ CONFIG_SND_ATMEL_SOC=y
CONFIG_SND_AT91_SOC_SAM9G20_WM8731=y
CONFIG_SND_ATMEL_SOC_WM8904=y
CONFIG_SND_AT91_SOC_SAM9X5_WM8731=y
+CONFIG_SND_ATMEL_SOC_CLASSD=y
+CONFIG_SND_SOC_MIKROE_PROTO=m
+CONFIG_SND_MCHP_SOC_I2S_MCC=y
CONFIG_USB=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
CONFIG_USB_EHCI_HCD=y
@@ -167,9 +176,11 @@ CONFIG_RTC_DRV_AT91RM9200=y
CONFIG_RTC_DRV_AT91SAM9=y
CONFIG_DMADEVICES=y
CONFIG_AT_HDMAC=y
+CONFIG_AT_XDMAC=y
# CONFIG_IOMMU_SUPPORT is not set
CONFIG_IIO=y
CONFIG_AT91_ADC=y
+CONFIG_AT91_SAMA5D2_ADC=y
CONFIG_PWM=y
CONFIG_PWM_ATMEL=y
CONFIG_PWM_ATMEL_HLCDC_PWM=y
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-11-29 13:52 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-11-29 13:51 [PATCH v3 0/9] SoC and defconfig support for SAM9X60 Claudiu Beznea
2019-11-29 13:51 ` Claudiu Beznea
2019-11-29 13:51 ` [PATCH v3 1/9] ARM: at91: Kconfig: add sam9x60 pll config flag Claudiu Beznea
2019-11-29 13:51 ` Claudiu Beznea
2019-11-29 13:51 ` [PATCH v3 2/9] ARM: at91: Kconfig: add config flag for SAM9X60 SoC Claudiu Beznea
2019-11-29 13:51 ` Claudiu Beznea
2019-11-29 13:51 ` [PATCH v3 3/9] ARM: at91: pm: move SAM9X60's PM under its own SoC config flag Claudiu Beznea
2019-11-29 13:51 ` Claudiu Beznea
2019-11-29 13:51 ` [PATCH v3 4/9] drivers: soc: atmel: move sam9x60 under its own " Claudiu Beznea
2019-11-29 13:51 ` Claudiu Beznea
2019-11-29 13:51 ` [PATCH v3 5/9] power: reset: Kconfig: select POWER_RESET_AT91_RESET for sam9x60 Claudiu Beznea
2019-11-29 13:51 ` Claudiu Beznea
2019-11-29 13:51 ` [PATCH v3 6/9] drivers: soc: atmel: select POWER_RESET_AT91_SAMA5D2_SHDWC " Claudiu Beznea
2019-11-29 13:51 ` Claudiu Beznea
2019-11-29 13:51 ` [PATCH v3 7/9] ARM: debug-ll: select DEBUG_AT91_RM9200_DBGU " Claudiu Beznea
2019-11-29 13:51 ` Claudiu Beznea
2019-11-29 13:51 ` [PATCH v3 8/9] ARM: at91/defconfig: use savedefconfig Claudiu Beznea
2019-11-29 13:51 ` Claudiu Beznea
2019-11-29 13:51 ` Claudiu Beznea [this message]
2019-11-29 13:51 ` [PATCH v3 9/9] ARM: at91/defconfig: enable config flags for sam9x60 SoC Claudiu Beznea
2019-12-09 23:45 ` [PATCH v3 0/9] SoC and defconfig support for SAM9X60 Alexandre Belloni
2019-12-09 23:45 ` Alexandre Belloni
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1575035505-6310-10-git-send-email-claudiu.beznea@microchip.com \
--to=claudiu.beznea@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=codrin.ciubotariu@microchip.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=ludovic.desroches@microchip.com \
--cc=nicolas.ferre@microchip.com \
--cc=sre@kernel.org \
--cc=tudor.ambarus@microchip.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.