From: Mason Yang <masonccyang@mxic.com.tw> To: broonie@kernel.org, tudor.ambarus@microchip.com, miquel.raynal@bootlin.com, richard@nod.at, vigneshr@ti.com, boris.brezillon@collabora.com, matthias.bgg@gmail.com Cc: p.yadav@ti.com, juliensu@mxic.com.tw, linux-kernel@vger.kernel.org, linux-mtd@lists.infradead.org, linux-spi@vger.kernel.org, Mason Yang <masonccyang@mxic.com.tw> Subject: [PATCH v3 00/14] mtd: spi-nor: add xSPI Octal DTR support Date: Thu, 28 May 2020 15:58:02 +0800 [thread overview] Message-ID: <1590652696-8844-1-git-send-email-masonccyang@mxic.com.tw> (raw) Hello, JESD216C has defined specification for Octal 8S-8S-8S and 8D-8D-8D. Based on JEDEC216C Basic Flash Parameter Table (BFPT) driver extract DWORD-18: command and command extension type. DWORD-20: Maximum operation speed of device in Octal mode. xSPI profile 1.0 table: DWORD-1: Read Fast command, the number of dummy cycles and address nbytes for Read Status Register command. DWORD-2: Read/Write volatile Register command for CFG Reg2. DWORD-4 and DWORD-5: dummy cycles used for various frequencies based on maximum speed of device from BFPT 20th DWORD. Ccommand sequences to change to octal DTR mode: The length of each command sequence is 8 per byte for single SPI mode and patching driver to parse and execute these sequences for octal DTR mode. By Vignesh's comments to patch these drivers based on Pratyush's patches set [1]. This series adds support for Macronix mx25uw51245g works in octal DTR mode. Tested on Macronix's Zynq PicoZed board with Macronix's SPI controller (spi-mxic.c) driver patched on mx25uw51245g Octal flash. [1] https://patchwork.ozlabs.org/project/linux-mtd/cover/20200525091544.17270-1-p.yadav@ti.com/ Summary of change log v3: Add support command sequences to change octal DTR mode and based on part of Pratyush's patches set. v2: Parse BFPT & xSPI table for Octal 8D-8D-8D mode parameters and enable Octal mode in spi_nor_late_init_params(). Using Macros in spi_nor_spimem_read_data, spi_nor_spimem_write_data and so on by Vignesh comments. v1: Without parsing BFPT & xSPI profile 1.0 table and enter Octal 8D-8D-8D mode directly in spi_nor_fixups hooks. thnaks for your time and review. best regards, Mason -- Mason Yang (7): mtd: spi-nor: sfdp: get octal mode maximum speed from BFPT mtd: spi-nor: sfdp: parse xSPI Profile 1.0 table mtd: spi-nor: sfdp: parse command sequences to change octal DTR mode mtd: spi-nor: core: add configuration register 2 read & write support spi: mxic: patch for octal DTR mode support mtd: spi-nor: core: execute command sequences to change octal DTR mode mtd: spi-nor: macronix: Add Octal 8D-8D-8D supports for Macronix mx25uw51245g Pratyush Yadav (7): spi: spi-mem: allow specifying whether an op is DTR or not spi: spi-mem: allow specifying a command's extension mtd: spi-nor: add support for DTR protocol mtd: spi-nor: sfdp: prepare BFPT parsing for JESD216 rev D mtd: spi-nor: sfdp: get command opcode extension type from BFPT mtd: spi-nor: core: use dummy cycle and address width info from SFDP mtd: spi-nor: core: enable octal DTR mode when possible drivers/mtd/spi-nor/core.c | 514 +++++++++++++++++++++++++++++++++++------ drivers/mtd/spi-nor/core.h | 49 ++++ drivers/mtd/spi-nor/macronix.c | 55 +++++ drivers/mtd/spi-nor/sfdp.c | 278 +++++++++++++++++++++- drivers/mtd/spi-nor/sfdp.h | 15 +- drivers/spi/spi-mem.c | 16 +- drivers/spi/spi-mtk-nor.c | 4 +- drivers/spi/spi-mxic.c | 101 +++++--- drivers/spi/spi-zynq-qspi.c | 11 +- include/linux/mtd/spi-nor.h | 51 ++-- include/linux/spi/spi-mem.h | 14 +- 11 files changed, 980 insertions(+), 128 deletions(-) -- 1.9.1
WARNING: multiple messages have this Message-ID (diff)
From: Mason Yang <masonccyang@mxic.com.tw> To: broonie@kernel.org, tudor.ambarus@microchip.com, miquel.raynal@bootlin.com, richard@nod.at, vigneshr@ti.com, boris.brezillon@collabora.com, matthias.bgg@gmail.com Cc: juliensu@mxic.com.tw, linux-kernel@vger.kernel.org, linux-spi@vger.kernel.org, linux-mtd@lists.infradead.org, Mason Yang <masonccyang@mxic.com.tw>, p.yadav@ti.com Subject: [PATCH v3 00/14] mtd: spi-nor: add xSPI Octal DTR support Date: Thu, 28 May 2020 15:58:02 +0800 [thread overview] Message-ID: <1590652696-8844-1-git-send-email-masonccyang@mxic.com.tw> (raw) Hello, JESD216C has defined specification for Octal 8S-8S-8S and 8D-8D-8D. Based on JEDEC216C Basic Flash Parameter Table (BFPT) driver extract DWORD-18: command and command extension type. DWORD-20: Maximum operation speed of device in Octal mode. xSPI profile 1.0 table: DWORD-1: Read Fast command, the number of dummy cycles and address nbytes for Read Status Register command. DWORD-2: Read/Write volatile Register command for CFG Reg2. DWORD-4 and DWORD-5: dummy cycles used for various frequencies based on maximum speed of device from BFPT 20th DWORD. Ccommand sequences to change to octal DTR mode: The length of each command sequence is 8 per byte for single SPI mode and patching driver to parse and execute these sequences for octal DTR mode. By Vignesh's comments to patch these drivers based on Pratyush's patches set [1]. This series adds support for Macronix mx25uw51245g works in octal DTR mode. Tested on Macronix's Zynq PicoZed board with Macronix's SPI controller (spi-mxic.c) driver patched on mx25uw51245g Octal flash. [1] https://patchwork.ozlabs.org/project/linux-mtd/cover/20200525091544.17270-1-p.yadav@ti.com/ Summary of change log v3: Add support command sequences to change octal DTR mode and based on part of Pratyush's patches set. v2: Parse BFPT & xSPI table for Octal 8D-8D-8D mode parameters and enable Octal mode in spi_nor_late_init_params(). Using Macros in spi_nor_spimem_read_data, spi_nor_spimem_write_data and so on by Vignesh comments. v1: Without parsing BFPT & xSPI profile 1.0 table and enter Octal 8D-8D-8D mode directly in spi_nor_fixups hooks. thnaks for your time and review. best regards, Mason -- Mason Yang (7): mtd: spi-nor: sfdp: get octal mode maximum speed from BFPT mtd: spi-nor: sfdp: parse xSPI Profile 1.0 table mtd: spi-nor: sfdp: parse command sequences to change octal DTR mode mtd: spi-nor: core: add configuration register 2 read & write support spi: mxic: patch for octal DTR mode support mtd: spi-nor: core: execute command sequences to change octal DTR mode mtd: spi-nor: macronix: Add Octal 8D-8D-8D supports for Macronix mx25uw51245g Pratyush Yadav (7): spi: spi-mem: allow specifying whether an op is DTR or not spi: spi-mem: allow specifying a command's extension mtd: spi-nor: add support for DTR protocol mtd: spi-nor: sfdp: prepare BFPT parsing for JESD216 rev D mtd: spi-nor: sfdp: get command opcode extension type from BFPT mtd: spi-nor: core: use dummy cycle and address width info from SFDP mtd: spi-nor: core: enable octal DTR mode when possible drivers/mtd/spi-nor/core.c | 514 +++++++++++++++++++++++++++++++++++------ drivers/mtd/spi-nor/core.h | 49 ++++ drivers/mtd/spi-nor/macronix.c | 55 +++++ drivers/mtd/spi-nor/sfdp.c | 278 +++++++++++++++++++++- drivers/mtd/spi-nor/sfdp.h | 15 +- drivers/spi/spi-mem.c | 16 +- drivers/spi/spi-mtk-nor.c | 4 +- drivers/spi/spi-mxic.c | 101 +++++--- drivers/spi/spi-zynq-qspi.c | 11 +- include/linux/mtd/spi-nor.h | 51 ++-- include/linux/spi/spi-mem.h | 14 +- 11 files changed, 980 insertions(+), 128 deletions(-) -- 1.9.1 ______________________________________________________ Linux MTD discussion mailing list http://lists.infradead.org/mailman/listinfo/linux-mtd/
next reply other threads:[~2020-05-28 7:58 UTC|newest] Thread overview: 37+ messages / expand[flat|nested] mbox.gz Atom feed top 2020-05-28 7:58 Mason Yang [this message] 2020-05-28 7:58 ` [PATCH v3 00/14] mtd: spi-nor: add xSPI Octal DTR support Mason Yang 2020-05-28 7:58 ` [PATCH v3 01/14] spi: spi-mem: allow specifying whether an op is DTR or not Mason Yang 2020-05-28 7:58 ` Mason Yang 2020-05-28 7:58 ` [PATCH v3 02/14] spi: spi-mem: allow specifying a command's extension Mason Yang 2020-05-28 7:58 ` Mason Yang 2020-05-28 7:58 ` [PATCH v3 03/14] mtd: spi-nor: add support for DTR protocol Mason Yang 2020-05-28 7:58 ` Mason Yang 2020-05-28 7:58 ` [PATCH v3 04/14] mtd: spi-nor: sfdp: prepare BFPT parsing for JESD216 rev D Mason Yang 2020-05-28 7:58 ` Mason Yang 2020-05-28 7:58 ` [PATCH v3 05/14] mtd: spi-nor: sfdp: get command opcode extension type from BFPT Mason Yang 2020-05-28 7:58 ` Mason Yang 2020-05-28 7:58 ` [PATCH v3 06/14] mtd: spi-nor: sfdp: get octal mode maximum speed " Mason Yang 2020-05-28 7:58 ` Mason Yang 2020-05-28 7:58 ` [PATCH v3 07/14] mtd: spi-nor: sfdp: parse xSPI Profile 1.0 table Mason Yang 2020-05-28 7:58 ` Mason Yang 2020-05-28 7:58 ` [PATCH v3 08/14] mtd: spi-nor: sfdp: parse command sequences to change octal DTR mode Mason Yang 2020-05-28 7:58 ` Mason Yang 2020-05-28 7:58 ` [PATCH v3 09/14] mtd: spi-nor: core: add configuration register 2 read & write support Mason Yang 2020-05-28 7:58 ` Mason Yang 2020-05-28 7:58 ` [PATCH v3 10/14] mtd: spi-nor: core: use dummy cycle and address width info from SFDP Mason Yang 2020-05-28 7:58 ` Mason Yang 2020-05-28 7:58 ` [PATCH v3 11/14] mtd: spi-nor: core: enable octal DTR mode when possible Mason Yang 2020-05-28 7:58 ` Mason Yang 2020-05-28 7:58 ` [PATCH v3 12/14] spi: mxic: patch for octal DTR mode support Mason Yang 2020-05-28 7:58 ` Mason Yang 2020-05-28 21:44 ` kbuild test robot 2020-05-28 21:44 ` kbuild test robot 2020-05-28 21:44 ` kbuild test robot 2020-05-28 7:58 ` [PATCH v3 13/14] mtd: spi-nor: core: execute command sequences to change octal DTR mode Mason Yang 2020-05-28 7:58 ` Mason Yang 2020-05-28 7:58 ` [PATCH v3 14/14] mtd: spi-nor: macronix: Add Octal 8D-8D-8D supports for Macronix mx25uw51245g Mason Yang 2020-05-28 7:58 ` Mason Yang 2020-05-28 8:26 ` [PATCH v3 00/14] mtd: spi-nor: add xSPI Octal DTR support Boris Brezillon 2020-05-28 8:26 ` Boris Brezillon 2020-05-29 5:27 ` masonccyang 2020-05-29 5:27 ` masonccyang
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1590652696-8844-1-git-send-email-masonccyang@mxic.com.tw \ --to=masonccyang@mxic.com.tw \ --cc=boris.brezillon@collabora.com \ --cc=broonie@kernel.org \ --cc=juliensu@mxic.com.tw \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-mtd@lists.infradead.org \ --cc=linux-spi@vger.kernel.org \ --cc=matthias.bgg@gmail.com \ --cc=miquel.raynal@bootlin.com \ --cc=p.yadav@ti.com \ --cc=richard@nod.at \ --cc=tudor.ambarus@microchip.com \ --cc=vigneshr@ti.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.