All of lore.kernel.org
 help / color / mirror / Atom feed
From: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
To: andrew.murray@arm.com, maz@kernel.org, linux-kernel@vger.kernel.org
Cc: james.quinlan@broadcom.com, mbrugger@suse.com,
	f.fainelli@gmail.com, phil@raspberrypi.org, wahrenst@gmx.net,
	jeremy.linton@arm.com, linux-pci@vger.kernel.org,
	linux-rpi-kernel@lists.infradead.org,
	Nicolas Saenz Julienne <nsaenzjulienne@suse.de>,
	Robin Murphy <robin.murphy@arm.com>,
	linux-arm-kernel@lists.infradead.org,
	bcm-kernel-feedback-list@broadcom.com,
	devicetree@vger.kernel.org, linux-acpi@vger.kernel.org,
	linux-clk@vger.kernel.org, linux-rdma@vger.kernel.org,
	iommu@lists.linux-foundation.org, netdev@vger.kernel.org,
	linux-rockchip@lists.infradead.org, kexec@lists.infradead.org,
	linux-nfs@vger.kernel.org
Subject: [PATCH v4 0/8] Raspberry Pi 4 PCIe support
Date: Tue,  3 Dec 2019 12:47:33 +0100	[thread overview]
Message-ID: <20191203114743.1294-1-nsaenzjulienne@suse.de> (raw)

This series aims at providing support for Raspberry Pi 4's PCIe
controller, which is also shared with the Broadcom STB family of
devices.

There was a previous attempt to upstream this some years ago[1] but was
blocked as most STB PCIe integrations have a sparse DMA mapping[2] which
is something currently not supported by the kernel.  Luckily this is not
the case for the Raspberry Pi 4.

Note that the driver code is to be based on top of Rob Herring's series
simplifying inbound and outbound range parsing.

[1] https://patchwork.kernel.org/cover/10605933/
[2] https://patchwork.kernel.org/patch/10605957/

---

Changes since v3:
  - Moved all the log2.h related changes at the end of the series, as I
    presume they will be contentious and I don't want the PCIe patches
    to depend on them. Ultimately I think I'll respin them on their own
    series but wanted to keep them in for this submission just for the
    sake of continuity.
  - Addressed small nits here and there.

Changes since v2:
  - Redo register access in driver avoiding indirection while keeping
    the naming intact
  - Add patch editing ARM64's config
  - Last MSI cleanups, notably removing MSIX flag
  - Got rid of all _RB writes
  - Got rid of all of_data
  - Overall churn removal
  - Address the rest of Andrew's comments

Changes since v1:
  - add generic rounddown/roundup_pow_two64() patch
  - Add MAINTAINERS patch
  - Fix Kconfig
  - Cleanup probe, use up to date APIs, exit on MSI failure
  - Get rid of linux,pci-domain and other unused constructs
  - Use edge triggered setup for MSI
  - Cleanup MSI implementation
  - Fix multiple cosmetic issues
  - Remove supend/resume code

Jim Quinlan (3):
  dt-bindings: PCI: Add bindings for brcmstb's PCIe device
  PCI: brcmstb: Add Broadcom STB PCIe host controller driver
  PCI: brcmstb: Add MSI support

Nicolas Saenz Julienne (5):
  ARM: dts: bcm2711: Enable PCIe controller
  MAINTAINERS: Add brcmstb PCIe controller
  arm64: defconfig: Enable Broadcom's STB PCIe controller
  linux/log2.h: Fix 64bit calculations in roundup/down_pow_two()
  linux/log2.h: Use roundup/dow_pow_two() on 64bit calculations

 .../bindings/pci/brcm,stb-pcie.yaml           |   97 ++
 MAINTAINERS                                   |    4 +
 arch/arm/boot/dts/bcm2711.dtsi                |   37 +
 arch/arm64/configs/defconfig                  |    1 +
 drivers/acpi/arm64/iort.c                     |    2 +-
 drivers/clk/clk-divider.c                     |    8 +-
 drivers/clk/sunxi/clk-sunxi.c                 |    2 +-
 drivers/infiniband/hw/hfi1/chip.c             |    4 +-
 drivers/infiniband/hw/hfi1/init.c             |    4 +-
 drivers/infiniband/hw/mlx4/srq.c              |    2 +-
 drivers/infiniband/hw/mthca/mthca_srq.c       |    2 +-
 drivers/infiniband/sw/rxe/rxe_qp.c            |    4 +-
 drivers/iommu/intel-iommu.c                   |    4 +-
 drivers/iommu/intel-svm.c                     |    4 +-
 drivers/iommu/intel_irq_remapping.c           |    2 +-
 drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c  |    4 +-
 drivers/net/ethernet/marvell/sky2.c           |    2 +-
 drivers/net/ethernet/mellanox/mlx4/en_clock.c |    3 +-
 drivers/net/ethernet/rocker/rocker_hw.h       |    4 +-
 drivers/net/ethernet/sfc/ef10.c               |    2 +-
 drivers/net/ethernet/sfc/efx.h                |    2 +-
 drivers/net/ethernet/sfc/falcon/efx.h         |    2 +-
 drivers/of/device.c                           |    3 +-
 drivers/pci/controller/Kconfig                |    9 +
 drivers/pci/controller/Makefile               |    1 +
 .../pci/controller/cadence/pcie-cadence-ep.c  |    3 +-
 drivers/pci/controller/cadence/pcie-cadence.c |    3 +-
 drivers/pci/controller/pcie-brcmstb.c         | 1008 +++++++++++++++++
 drivers/pci/controller/pcie-rockchip-ep.c     |    5 +-
 drivers/pci/msi.c                             |    2 +-
 include/linux/log2.h                          |   44 +-
 kernel/dma/direct.c                           |    2 +-
 kernel/kexec_core.c                           |    3 +-
 lib/rhashtable.c                              |    2 +-
 net/sunrpc/xprtrdma/verbs.c                   |    2 +-
 35 files changed, 1211 insertions(+), 72 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml
 create mode 100644 drivers/pci/controller/pcie-brcmstb.c

-- 
2.24.0


WARNING: multiple messages have this Message-ID (diff)
From: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
To: andrew.murray@arm.com, maz@kernel.org, linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
	linux-nfs@vger.kernel.org, f.fainelli@gmail.com,
	linux-rockchip@lists.infradead.org, linux-rdma@vger.kernel.org,
	linux-pci@vger.kernel.org, phil@raspberrypi.org,
	jeremy.linton@arm.com, kexec@lists.infradead.org,
	linux-acpi@vger.kernel.org, iommu@lists.linux-foundation.org,
	mbrugger@suse.com, bcm-kernel-feedback-list@broadcom.com,
	wahrenst@gmx.net, james.quinlan@broadcom.com,
	netdev@vger.kernel.org, Robin Murphy <robin.murphy@arm.com>,
	linux-clk@vger.kernel.org,
	Nicolas Saenz Julienne <nsaenzjulienne@suse.de>,
	linux-rpi-kernel@lists.infradead.org
Subject: [PATCH v4 0/8] Raspberry Pi 4 PCIe support
Date: Tue,  3 Dec 2019 12:47:33 +0100	[thread overview]
Message-ID: <20191203114743.1294-1-nsaenzjulienne@suse.de> (raw)

This series aims at providing support for Raspberry Pi 4's PCIe
controller, which is also shared with the Broadcom STB family of
devices.

There was a previous attempt to upstream this some years ago[1] but was
blocked as most STB PCIe integrations have a sparse DMA mapping[2] which
is something currently not supported by the kernel.  Luckily this is not
the case for the Raspberry Pi 4.

Note that the driver code is to be based on top of Rob Herring's series
simplifying inbound and outbound range parsing.

[1] https://patchwork.kernel.org/cover/10605933/
[2] https://patchwork.kernel.org/patch/10605957/

---

Changes since v3:
  - Moved all the log2.h related changes at the end of the series, as I
    presume they will be contentious and I don't want the PCIe patches
    to depend on them. Ultimately I think I'll respin them on their own
    series but wanted to keep them in for this submission just for the
    sake of continuity.
  - Addressed small nits here and there.

Changes since v2:
  - Redo register access in driver avoiding indirection while keeping
    the naming intact
  - Add patch editing ARM64's config
  - Last MSI cleanups, notably removing MSIX flag
  - Got rid of all _RB writes
  - Got rid of all of_data
  - Overall churn removal
  - Address the rest of Andrew's comments

Changes since v1:
  - add generic rounddown/roundup_pow_two64() patch
  - Add MAINTAINERS patch
  - Fix Kconfig
  - Cleanup probe, use up to date APIs, exit on MSI failure
  - Get rid of linux,pci-domain and other unused constructs
  - Use edge triggered setup for MSI
  - Cleanup MSI implementation
  - Fix multiple cosmetic issues
  - Remove supend/resume code

Jim Quinlan (3):
  dt-bindings: PCI: Add bindings for brcmstb's PCIe device
  PCI: brcmstb: Add Broadcom STB PCIe host controller driver
  PCI: brcmstb: Add MSI support

Nicolas Saenz Julienne (5):
  ARM: dts: bcm2711: Enable PCIe controller
  MAINTAINERS: Add brcmstb PCIe controller
  arm64: defconfig: Enable Broadcom's STB PCIe controller
  linux/log2.h: Fix 64bit calculations in roundup/down_pow_two()
  linux/log2.h: Use roundup/dow_pow_two() on 64bit calculations

 .../bindings/pci/brcm,stb-pcie.yaml           |   97 ++
 MAINTAINERS                                   |    4 +
 arch/arm/boot/dts/bcm2711.dtsi                |   37 +
 arch/arm64/configs/defconfig                  |    1 +
 drivers/acpi/arm64/iort.c                     |    2 +-
 drivers/clk/clk-divider.c                     |    8 +-
 drivers/clk/sunxi/clk-sunxi.c                 |    2 +-
 drivers/infiniband/hw/hfi1/chip.c             |    4 +-
 drivers/infiniband/hw/hfi1/init.c             |    4 +-
 drivers/infiniband/hw/mlx4/srq.c              |    2 +-
 drivers/infiniband/hw/mthca/mthca_srq.c       |    2 +-
 drivers/infiniband/sw/rxe/rxe_qp.c            |    4 +-
 drivers/iommu/intel-iommu.c                   |    4 +-
 drivers/iommu/intel-svm.c                     |    4 +-
 drivers/iommu/intel_irq_remapping.c           |    2 +-
 drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c  |    4 +-
 drivers/net/ethernet/marvell/sky2.c           |    2 +-
 drivers/net/ethernet/mellanox/mlx4/en_clock.c |    3 +-
 drivers/net/ethernet/rocker/rocker_hw.h       |    4 +-
 drivers/net/ethernet/sfc/ef10.c               |    2 +-
 drivers/net/ethernet/sfc/efx.h                |    2 +-
 drivers/net/ethernet/sfc/falcon/efx.h         |    2 +-
 drivers/of/device.c                           |    3 +-
 drivers/pci/controller/Kconfig                |    9 +
 drivers/pci/controller/Makefile               |    1 +
 .../pci/controller/cadence/pcie-cadence-ep.c  |    3 +-
 drivers/pci/controller/cadence/pcie-cadence.c |    3 +-
 drivers/pci/controller/pcie-brcmstb.c         | 1008 +++++++++++++++++
 drivers/pci/controller/pcie-rockchip-ep.c     |    5 +-
 drivers/pci/msi.c                             |    2 +-
 include/linux/log2.h                          |   44 +-
 kernel/dma/direct.c                           |    2 +-
 kernel/kexec_core.c                           |    3 +-
 lib/rhashtable.c                              |    2 +-
 net/sunrpc/xprtrdma/verbs.c                   |    2 +-
 35 files changed, 1211 insertions(+), 72 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml
 create mode 100644 drivers/pci/controller/pcie-brcmstb.c

-- 
2.24.0

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

WARNING: multiple messages have this Message-ID (diff)
From: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
To: andrew.murray@arm.com, maz@kernel.org, linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
	linux-nfs@vger.kernel.org, f.fainelli@gmail.com,
	linux-rockchip@lists.infradead.org, linux-rdma@vger.kernel.org,
	linux-pci@vger.kernel.org, phil@raspberrypi.org,
	jeremy.linton@arm.com, kexec@lists.infradead.org,
	linux-acpi@vger.kernel.org, iommu@lists.linux-foundation.org,
	mbrugger@suse.com, bcm-kernel-feedback-list@broadcom.com,
	wahrenst@gmx.net, james.quinlan@broadcom.com,
	netdev@vger.kernel.org, Robin Murphy <robin.murphy@arm.com>,
	linux-clk@vger.kernel.org,
	Nicolas Saenz Julienne <nsaenzjulienne@suse.de>,
	linux-rpi-kernel@lists.infradead.org
Subject: [PATCH v4 0/8] Raspberry Pi 4 PCIe support
Date: Tue,  3 Dec 2019 12:47:33 +0100	[thread overview]
Message-ID: <20191203114743.1294-1-nsaenzjulienne@suse.de> (raw)

This series aims at providing support for Raspberry Pi 4's PCIe
controller, which is also shared with the Broadcom STB family of
devices.

There was a previous attempt to upstream this some years ago[1] but was
blocked as most STB PCIe integrations have a sparse DMA mapping[2] which
is something currently not supported by the kernel.  Luckily this is not
the case for the Raspberry Pi 4.

Note that the driver code is to be based on top of Rob Herring's series
simplifying inbound and outbound range parsing.

[1] https://patchwork.kernel.org/cover/10605933/
[2] https://patchwork.kernel.org/patch/10605957/

---

Changes since v3:
  - Moved all the log2.h related changes at the end of the series, as I
    presume they will be contentious and I don't want the PCIe patches
    to depend on them. Ultimately I think I'll respin them on their own
    series but wanted to keep them in for this submission just for the
    sake of continuity.
  - Addressed small nits here and there.

Changes since v2:
  - Redo register access in driver avoiding indirection while keeping
    the naming intact
  - Add patch editing ARM64's config
  - Last MSI cleanups, notably removing MSIX flag
  - Got rid of all _RB writes
  - Got rid of all of_data
  - Overall churn removal
  - Address the rest of Andrew's comments

Changes since v1:
  - add generic rounddown/roundup_pow_two64() patch
  - Add MAINTAINERS patch
  - Fix Kconfig
  - Cleanup probe, use up to date APIs, exit on MSI failure
  - Get rid of linux,pci-domain and other unused constructs
  - Use edge triggered setup for MSI
  - Cleanup MSI implementation
  - Fix multiple cosmetic issues
  - Remove supend/resume code

Jim Quinlan (3):
  dt-bindings: PCI: Add bindings for brcmstb's PCIe device
  PCI: brcmstb: Add Broadcom STB PCIe host controller driver
  PCI: brcmstb: Add MSI support

Nicolas Saenz Julienne (5):
  ARM: dts: bcm2711: Enable PCIe controller
  MAINTAINERS: Add brcmstb PCIe controller
  arm64: defconfig: Enable Broadcom's STB PCIe controller
  linux/log2.h: Fix 64bit calculations in roundup/down_pow_two()
  linux/log2.h: Use roundup/dow_pow_two() on 64bit calculations

 .../bindings/pci/brcm,stb-pcie.yaml           |   97 ++
 MAINTAINERS                                   |    4 +
 arch/arm/boot/dts/bcm2711.dtsi                |   37 +
 arch/arm64/configs/defconfig                  |    1 +
 drivers/acpi/arm64/iort.c                     |    2 +-
 drivers/clk/clk-divider.c                     |    8 +-
 drivers/clk/sunxi/clk-sunxi.c                 |    2 +-
 drivers/infiniband/hw/hfi1/chip.c             |    4 +-
 drivers/infiniband/hw/hfi1/init.c             |    4 +-
 drivers/infiniband/hw/mlx4/srq.c              |    2 +-
 drivers/infiniband/hw/mthca/mthca_srq.c       |    2 +-
 drivers/infiniband/sw/rxe/rxe_qp.c            |    4 +-
 drivers/iommu/intel-iommu.c                   |    4 +-
 drivers/iommu/intel-svm.c                     |    4 +-
 drivers/iommu/intel_irq_remapping.c           |    2 +-
 drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c  |    4 +-
 drivers/net/ethernet/marvell/sky2.c           |    2 +-
 drivers/net/ethernet/mellanox/mlx4/en_clock.c |    3 +-
 drivers/net/ethernet/rocker/rocker_hw.h       |    4 +-
 drivers/net/ethernet/sfc/ef10.c               |    2 +-
 drivers/net/ethernet/sfc/efx.h                |    2 +-
 drivers/net/ethernet/sfc/falcon/efx.h         |    2 +-
 drivers/of/device.c                           |    3 +-
 drivers/pci/controller/Kconfig                |    9 +
 drivers/pci/controller/Makefile               |    1 +
 .../pci/controller/cadence/pcie-cadence-ep.c  |    3 +-
 drivers/pci/controller/cadence/pcie-cadence.c |    3 +-
 drivers/pci/controller/pcie-brcmstb.c         | 1008 +++++++++++++++++
 drivers/pci/controller/pcie-rockchip-ep.c     |    5 +-
 drivers/pci/msi.c                             |    2 +-
 include/linux/log2.h                          |   44 +-
 kernel/dma/direct.c                           |    2 +-
 kernel/kexec_core.c                           |    3 +-
 lib/rhashtable.c                              |    2 +-
 net/sunrpc/xprtrdma/verbs.c                   |    2 +-
 35 files changed, 1211 insertions(+), 72 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml
 create mode 100644 drivers/pci/controller/pcie-brcmstb.c

-- 
2.24.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

WARNING: multiple messages have this Message-ID (diff)
From: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
To: andrew.murray@arm.com, maz@kernel.org, linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
	linux-nfs@vger.kernel.org, f.fainelli@gmail.com,
	linux-rockchip@lists.infradead.org, linux-rdma@vger.kernel.org,
	linux-pci@vger.kernel.org, phil@raspberrypi.org,
	jeremy.linton@arm.com, kexec@lists.infradead.org,
	linux-acpi@vger.kernel.org, iommu@lists.linux-foundation.org,
	mbrugger@suse.com, bcm-kernel-feedback-list@broadcom.com,
	wahrenst@gmx.net, james.quinlan@broadcom.com,
	netdev@vger.kernel.org, Robin Murphy <robin.murphy@arm.com>,
	linux-clk@vger.kernel.org,
	Nicolas Saenz Julienne <nsaenzjulienne@suse.de>,
	linux-rpi-kernel@lists.infradead.org
Subject: [PATCH v4 0/8] Raspberry Pi 4 PCIe support
Date: Tue,  3 Dec 2019 12:47:33 +0100	[thread overview]
Message-ID: <20191203114743.1294-1-nsaenzjulienne@suse.de> (raw)

This series aims at providing support for Raspberry Pi 4's PCIe
controller, which is also shared with the Broadcom STB family of
devices.

There was a previous attempt to upstream this some years ago[1] but was
blocked as most STB PCIe integrations have a sparse DMA mapping[2] which
is something currently not supported by the kernel.  Luckily this is not
the case for the Raspberry Pi 4.

Note that the driver code is to be based on top of Rob Herring's series
simplifying inbound and outbound range parsing.

[1] https://patchwork.kernel.org/cover/10605933/
[2] https://patchwork.kernel.org/patch/10605957/

---

Changes since v3:
  - Moved all the log2.h related changes at the end of the series, as I
    presume they will be contentious and I don't want the PCIe patches
    to depend on them. Ultimately I think I'll respin them on their own
    series but wanted to keep them in for this submission just for the
    sake of continuity.
  - Addressed small nits here and there.

Changes since v2:
  - Redo register access in driver avoiding indirection while keeping
    the naming intact
  - Add patch editing ARM64's config
  - Last MSI cleanups, notably removing MSIX flag
  - Got rid of all _RB writes
  - Got rid of all of_data
  - Overall churn removal
  - Address the rest of Andrew's comments

Changes since v1:
  - add generic rounddown/roundup_pow_two64() patch
  - Add MAINTAINERS patch
  - Fix Kconfig
  - Cleanup probe, use up to date APIs, exit on MSI failure
  - Get rid of linux,pci-domain and other unused constructs
  - Use edge triggered setup for MSI
  - Cleanup MSI implementation
  - Fix multiple cosmetic issues
  - Remove supend/resume code

Jim Quinlan (3):
  dt-bindings: PCI: Add bindings for brcmstb's PCIe device
  PCI: brcmstb: Add Broadcom STB PCIe host controller driver
  PCI: brcmstb: Add MSI support

Nicolas Saenz Julienne (5):
  ARM: dts: bcm2711: Enable PCIe controller
  MAINTAINERS: Add brcmstb PCIe controller
  arm64: defconfig: Enable Broadcom's STB PCIe controller
  linux/log2.h: Fix 64bit calculations in roundup/down_pow_two()
  linux/log2.h: Use roundup/dow_pow_two() on 64bit calculations

 .../bindings/pci/brcm,stb-pcie.yaml           |   97 ++
 MAINTAINERS                                   |    4 +
 arch/arm/boot/dts/bcm2711.dtsi                |   37 +
 arch/arm64/configs/defconfig                  |    1 +
 drivers/acpi/arm64/iort.c                     |    2 +-
 drivers/clk/clk-divider.c                     |    8 +-
 drivers/clk/sunxi/clk-sunxi.c                 |    2 +-
 drivers/infiniband/hw/hfi1/chip.c             |    4 +-
 drivers/infiniband/hw/hfi1/init.c             |    4 +-
 drivers/infiniband/hw/mlx4/srq.c              |    2 +-
 drivers/infiniband/hw/mthca/mthca_srq.c       |    2 +-
 drivers/infiniband/sw/rxe/rxe_qp.c            |    4 +-
 drivers/iommu/intel-iommu.c                   |    4 +-
 drivers/iommu/intel-svm.c                     |    4 +-
 drivers/iommu/intel_irq_remapping.c           |    2 +-
 drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c  |    4 +-
 drivers/net/ethernet/marvell/sky2.c           |    2 +-
 drivers/net/ethernet/mellanox/mlx4/en_clock.c |    3 +-
 drivers/net/ethernet/rocker/rocker_hw.h       |    4 +-
 drivers/net/ethernet/sfc/ef10.c               |    2 +-
 drivers/net/ethernet/sfc/efx.h                |    2 +-
 drivers/net/ethernet/sfc/falcon/efx.h         |    2 +-
 drivers/of/device.c                           |    3 +-
 drivers/pci/controller/Kconfig                |    9 +
 drivers/pci/controller/Makefile               |    1 +
 .../pci/controller/cadence/pcie-cadence-ep.c  |    3 +-
 drivers/pci/controller/cadence/pcie-cadence.c |    3 +-
 drivers/pci/controller/pcie-brcmstb.c         | 1008 +++++++++++++++++
 drivers/pci/controller/pcie-rockchip-ep.c     |    5 +-
 drivers/pci/msi.c                             |    2 +-
 include/linux/log2.h                          |   44 +-
 kernel/dma/direct.c                           |    2 +-
 kernel/kexec_core.c                           |    3 +-
 lib/rhashtable.c                              |    2 +-
 net/sunrpc/xprtrdma/verbs.c                   |    2 +-
 35 files changed, 1211 insertions(+), 72 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/pci/brcm,stb-pcie.yaml
 create mode 100644 drivers/pci/controller/pcie-brcmstb.c

-- 
2.24.0


_______________________________________________
kexec mailing list
kexec@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/kexec

             reply	other threads:[~2019-12-03 11:48 UTC|newest]

Thread overview: 71+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-12-03 11:47 Nicolas Saenz Julienne [this message]
2019-12-03 11:47 ` [PATCH v4 0/8] Raspberry Pi 4 PCIe support Nicolas Saenz Julienne
2019-12-03 11:47 ` Nicolas Saenz Julienne
2019-12-03 11:47 ` Nicolas Saenz Julienne
2019-12-03 11:47 ` [PATCH v4 1/8] dt-bindings: PCI: Add bindings for brcmstb's PCIe device Nicolas Saenz Julienne
2019-12-03 11:47   ` Nicolas Saenz Julienne
2019-12-03 15:03   ` Andrew Murray
2019-12-03 15:03     ` Andrew Murray
2019-12-03 11:47 ` [PATCH v4 2/8] ARM: dts: bcm2711: Enable PCIe controller Nicolas Saenz Julienne
2019-12-03 11:47   ` Nicolas Saenz Julienne
2019-12-16  6:46   ` Jian-Hong Pan
2019-12-16  6:46     ` Jian-Hong Pan
2019-12-16  9:49     ` Nicolas Saenz Julienne
2019-12-16  9:49       ` Nicolas Saenz Julienne
2019-12-03 11:47 ` [PATCH v4 3/8] PCI: brcmstb: Add Broadcom STB PCIe host controller driver Nicolas Saenz Julienne
2019-12-03 11:47   ` Nicolas Saenz Julienne
2019-12-03 11:47 ` [PATCH v4 4/8] PCI: brcmstb: Add MSI support Nicolas Saenz Julienne
2019-12-03 11:47   ` Nicolas Saenz Julienne
2019-12-03 11:47 ` [PATCH v4 5/8] MAINTAINERS: Add brcmstb PCIe controller Nicolas Saenz Julienne
2019-12-03 11:47 ` [PATCH v4 6/8] arm64: defconfig: Enable Broadcom's STB " Nicolas Saenz Julienne
2019-12-03 11:47   ` Nicolas Saenz Julienne
2019-12-03 11:47 ` [PATCH v4 7/8] linux/log2.h: Fix 64bit calculations in roundup/down_pow_two() Nicolas Saenz Julienne
2019-12-03 11:47   ` Nicolas Saenz Julienne
2019-12-03 11:47   ` Nicolas Saenz Julienne
2019-12-03 16:39   ` Chuck Lever
2019-12-03 16:39     ` Chuck Lever
2019-12-03 16:39     ` Chuck Lever
2019-12-03 16:39     ` Chuck Lever
2019-12-04 10:56   ` Martin Habets
2019-12-04 10:56     ` Martin Habets
2019-12-04 10:56     ` Martin Habets
2019-12-04 10:56     ` Martin Habets
2019-12-04 14:17   ` Leon Romanovsky
2019-12-04 14:17     ` Leon Romanovsky
2019-12-04 14:17     ` Leon Romanovsky
2019-12-05  0:39   ` Lu Baolu
2019-12-05  0:39     ` Lu Baolu
2019-12-05  0:39     ` Lu Baolu
2019-12-05 17:48   ` Robin Murphy
2019-12-05 17:48     ` Robin Murphy
2019-12-05 17:48     ` Robin Murphy
2019-12-12 12:31     ` Nicolas Saenz Julienne
2019-12-12 12:31       ` Nicolas Saenz Julienne
2019-12-12 12:31       ` Nicolas Saenz Julienne
2019-12-05 22:30   ` Bjorn Helgaas
2019-12-05 22:30     ` Bjorn Helgaas
2019-12-05 22:30     ` Bjorn Helgaas
2019-12-05 22:30     ` Bjorn Helgaas
2019-12-12 13:16     ` Nicolas Saenz Julienne
2019-12-12 13:16       ` Nicolas Saenz Julienne
2019-12-12 13:16       ` Nicolas Saenz Julienne
2019-12-12 13:16       ` Nicolas Saenz Julienne
2019-12-03 11:47 ` [PATCH v4 8/8] linux/log2.h: Use roundup/dow_pow_two() on 64bit calculations Nicolas Saenz Julienne
2019-12-03 11:47   ` Nicolas Saenz Julienne
2019-12-03 11:47   ` Nicolas Saenz Julienne
2019-12-03 15:53   ` Rob Herring
2019-12-03 15:53     ` Rob Herring
2019-12-03 15:53     ` Rob Herring
2019-12-03 15:53     ` Rob Herring
2019-12-03 16:06     ` Nicolas Saenz Julienne
2019-12-03 16:06       ` Nicolas Saenz Julienne
2019-12-03 16:06       ` Nicolas Saenz Julienne
2019-12-03 16:06       ` Nicolas Saenz Julienne
2019-12-05 20:38   ` Bjorn Helgaas
2019-12-05 20:38     ` Bjorn Helgaas
2019-12-05 20:38     ` Bjorn Helgaas
2019-12-05 20:38     ` Bjorn Helgaas
2019-12-12 13:21     ` Nicolas Saenz Julienne
2019-12-12 13:21       ` Nicolas Saenz Julienne
2019-12-12 13:21       ` Nicolas Saenz Julienne
2019-12-12 13:21       ` Nicolas Saenz Julienne

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20191203114743.1294-1-nsaenzjulienne@suse.de \
    --to=nsaenzjulienne@suse.de \
    --cc=andrew.murray@arm.com \
    --cc=bcm-kernel-feedback-list@broadcom.com \
    --cc=devicetree@vger.kernel.org \
    --cc=f.fainelli@gmail.com \
    --cc=iommu@lists.linux-foundation.org \
    --cc=james.quinlan@broadcom.com \
    --cc=jeremy.linton@arm.com \
    --cc=kexec@lists.infradead.org \
    --cc=linux-acpi@vger.kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-nfs@vger.kernel.org \
    --cc=linux-pci@vger.kernel.org \
    --cc=linux-rdma@vger.kernel.org \
    --cc=linux-rockchip@lists.infradead.org \
    --cc=linux-rpi-kernel@lists.infradead.org \
    --cc=maz@kernel.org \
    --cc=mbrugger@suse.com \
    --cc=netdev@vger.kernel.org \
    --cc=phil@raspberrypi.org \
    --cc=robin.murphy@arm.com \
    --cc=wahrenst@gmx.net \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.