From: <Codrin.Ciubotariu@microchip.com>
To: <linux-i2c@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>
Cc: <kamel.bouhara@bootlin.com>, <wsa@the-dreams.de>,
<Nicolas.Ferre@microchip.com>, <alexandre.belloni@bootlin.com>,
<Ludovic.Desroches@microchip.com>, <robh@kernel.org>
Subject: [PATCH v2 6/6] ARM: at91/dt: sama5d2: add i2c gpio pinctrl
Date: Fri, 3 Jan 2020 09:49:09 +0000 [thread overview]
Message-ID: <20200103094821.13185-7-codrin.ciubotariu@microchip.com> (raw)
In-Reply-To: <20200103094821.13185-1-codrin.ciubotariu@microchip.com>
From: Kamel Bouhara <kamel.bouhara@bootlin.com>
Add the i2c gpio pinctrls to support the i2c bus recovery
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
---
Changes in v2:
- new changes;
arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts | 33 +++++++++++++++++++--
arch/arm/boot/dts/at91-sama5d2_xplained.dts | 33 +++++++++++++++++++--
2 files changed, 60 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts b/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
index ba7f3e646c26..b3cd651ecda0 100644
--- a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
@@ -180,8 +180,11 @@
i2c0: i2c@f8028000 {
dmas = <0>, <0>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c0_default>;
+ pinctrl-1 = <&pinctrl_i2c0_gpio>;
+ sda-gpios = <&pioA PIN_PD21 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&pioA PIN_PD22 GPIO_ACTIVE_HIGH>;
status = "okay";
};
@@ -198,8 +201,11 @@
#address-cells = <1>;
#size-cells = <0>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_flx0_default>;
+ pinctrl-1 = <&pinctrl_flx0_gpio>;
+ sda-gpios = <&pioA PIN_PB28 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&pioA PIN_PB29 GPIO_ACTIVE_HIGH>;
atmel,fifo-size = <16>;
status = "okay";
};
@@ -226,8 +232,11 @@
i2c1: i2c@fc028000 {
dmas = <0>, <0>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1_default>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ sda-gpios = <&pioA PIN_PC6 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&pioA PIN_PC7 GPIO_ACTIVE_HIGH>;
status = "okay";
at24@50 {
@@ -244,18 +253,36 @@
bias-disable;
};
+ pinctrl_flx0_gpio: flx0_gpio {
+ pinmux = <PIN_PB28__GPIO>,
+ <PIN_PB29__GPIO>;
+ bias-pull-up;
+ };
+
pinctrl_i2c0_default: i2c0_default {
pinmux = <PIN_PD21__TWD0>,
<PIN_PD22__TWCK0>;
bias-disable;
};
+ pinctrl_i2c0_gpio: i2c0_gpio {
+ pinmux = <PIN_PD21__GPIO>,
+ <PIN_PD22__GPIO>;
+ bias-pull-up;
+ };
+
pinctrl_i2c1_default: i2c1_default {
pinmux = <PIN_PC6__TWD1>,
<PIN_PC7__TWCK1>;
bias-disable;
};
+ pinctrl_i2c1_gpio: i2c1_gpio {
+ pinmux = <PIN_PC6__GPIO>,
+ <PIN_PC7__GPIO>;
+ bias-pull-up;
+ };
+
pinctrl_key_gpio_default: key_gpio_default {
pinmux = <PIN_PA10__GPIO>;
bias-pull-up;
diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
index 9d0a7fbea725..500e49eeb8cc 100644
--- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
@@ -129,8 +129,11 @@
i2c0: i2c@f8028000 {
dmas = <0>, <0>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c0_default>;
+ pinctrl-1 = <&pinctrl_i2c0_gpio>;
+ sda-gpios = <&pioA PIN_PD21 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&pioA PIN_PD22 GPIO_ACTIVE_HIGH>;
i2c-sda-hold-time-ns = <350>;
status = "okay";
@@ -331,8 +334,11 @@
#address-cells = <1>;
#size-cells = <0>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 23>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_flx4_default>;
+ pinctrl-1 = <&pinctrl_flx4_gpio>;
+ sda-gpios = <&pioA PIN_PD12 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&pioA PIN_PD13 GPIO_ACTIVE_HIGH>;
atmel,fifo-size = <16>;
i2c-analog-filter;
i2c-digital-filter;
@@ -343,11 +349,14 @@
i2c1: i2c@fc028000 {
dmas = <0>, <0>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1_default>;
i2c-analog-filter;
i2c-digital-filter;
i2c-digital-filter-width-ns = <35>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ sda-gpios = <&pioA PIN_PD4 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&pioA PIN_PD5 GPIO_ACTIVE_HIGH>;
status = "okay";
at24@54 {
@@ -441,18 +450,36 @@
bias-disable;
};
+ pinctrl_flx4_gpio: flx4_gpio {
+ pinmux = <PIN_PD12__GPIO>,
+ <PIN_PD13__GPIO>;
+ bias-pull-up;
+ };
+
pinctrl_i2c0_default: i2c0_default {
pinmux = <PIN_PD21__TWD0>,
<PIN_PD22__TWCK0>;
bias-disable;
};
+ pinctrl_i2c0_gpio: i2c0_gpio {
+ pinmux = <PIN_PD21__GPIO>,
+ <PIN_PD22__GPIO>;
+ bias-pull-up;
+ };
+
pinctrl_i2c1_default: i2c1_default {
pinmux = <PIN_PD4__TWD1>,
<PIN_PD5__TWCK1>;
bias-disable;
};
+ pinctrl_i2c1_gpio: i2c1_gpio {
+ pinmux = <PIN_PD4__GPIO>,
+ <PIN_PD5__GPIO>;
+ bias-pull-up;
+ };
+
pinctrl_i2s0_default: i2s0_default {
pinmux = <PIN_PC1__I2SC0_CK>,
<PIN_PC2__I2SC0_MCK>,
--
2.20.1
WARNING: multiple messages have this Message-ID (diff)
From: <Codrin.Ciubotariu@microchip.com>
To: linux-i2c@vger.kernel.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Cc: kamel.bouhara@bootlin.com, wsa@the-dreams.de,
Nicolas.Ferre@microchip.com, alexandre.belloni@bootlin.com,
Ludovic.Desroches@microchip.com, robh@kernel.org
Subject: [PATCH v2 6/6] ARM: at91/dt: sama5d2: add i2c gpio pinctrl
Date: Fri, 3 Jan 2020 09:49:09 +0000 [thread overview]
Message-ID: <20200103094821.13185-7-codrin.ciubotariu@microchip.com> (raw)
In-Reply-To: <20200103094821.13185-1-codrin.ciubotariu@microchip.com>
From: Kamel Bouhara <kamel.bouhara@bootlin.com>
Add the i2c gpio pinctrls to support the i2c bus recovery
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
---
Changes in v2:
- new changes;
arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts | 33 +++++++++++++++++++--
arch/arm/boot/dts/at91-sama5d2_xplained.dts | 33 +++++++++++++++++++--
2 files changed, 60 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts b/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
index ba7f3e646c26..b3cd651ecda0 100644
--- a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
@@ -180,8 +180,11 @@
i2c0: i2c@f8028000 {
dmas = <0>, <0>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c0_default>;
+ pinctrl-1 = <&pinctrl_i2c0_gpio>;
+ sda-gpios = <&pioA PIN_PD21 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&pioA PIN_PD22 GPIO_ACTIVE_HIGH>;
status = "okay";
};
@@ -198,8 +201,11 @@
#address-cells = <1>;
#size-cells = <0>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_flx0_default>;
+ pinctrl-1 = <&pinctrl_flx0_gpio>;
+ sda-gpios = <&pioA PIN_PB28 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&pioA PIN_PB29 GPIO_ACTIVE_HIGH>;
atmel,fifo-size = <16>;
status = "okay";
};
@@ -226,8 +232,11 @@
i2c1: i2c@fc028000 {
dmas = <0>, <0>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1_default>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ sda-gpios = <&pioA PIN_PC6 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&pioA PIN_PC7 GPIO_ACTIVE_HIGH>;
status = "okay";
at24@50 {
@@ -244,18 +253,36 @@
bias-disable;
};
+ pinctrl_flx0_gpio: flx0_gpio {
+ pinmux = <PIN_PB28__GPIO>,
+ <PIN_PB29__GPIO>;
+ bias-pull-up;
+ };
+
pinctrl_i2c0_default: i2c0_default {
pinmux = <PIN_PD21__TWD0>,
<PIN_PD22__TWCK0>;
bias-disable;
};
+ pinctrl_i2c0_gpio: i2c0_gpio {
+ pinmux = <PIN_PD21__GPIO>,
+ <PIN_PD22__GPIO>;
+ bias-pull-up;
+ };
+
pinctrl_i2c1_default: i2c1_default {
pinmux = <PIN_PC6__TWD1>,
<PIN_PC7__TWCK1>;
bias-disable;
};
+ pinctrl_i2c1_gpio: i2c1_gpio {
+ pinmux = <PIN_PC6__GPIO>,
+ <PIN_PC7__GPIO>;
+ bias-pull-up;
+ };
+
pinctrl_key_gpio_default: key_gpio_default {
pinmux = <PIN_PA10__GPIO>;
bias-pull-up;
diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
index 9d0a7fbea725..500e49eeb8cc 100644
--- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
@@ -129,8 +129,11 @@
i2c0: i2c@f8028000 {
dmas = <0>, <0>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c0_default>;
+ pinctrl-1 = <&pinctrl_i2c0_gpio>;
+ sda-gpios = <&pioA PIN_PD21 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&pioA PIN_PD22 GPIO_ACTIVE_HIGH>;
i2c-sda-hold-time-ns = <350>;
status = "okay";
@@ -331,8 +334,11 @@
#address-cells = <1>;
#size-cells = <0>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 23>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_flx4_default>;
+ pinctrl-1 = <&pinctrl_flx4_gpio>;
+ sda-gpios = <&pioA PIN_PD12 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&pioA PIN_PD13 GPIO_ACTIVE_HIGH>;
atmel,fifo-size = <16>;
i2c-analog-filter;
i2c-digital-filter;
@@ -343,11 +349,14 @@
i2c1: i2c@fc028000 {
dmas = <0>, <0>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1_default>;
i2c-analog-filter;
i2c-digital-filter;
i2c-digital-filter-width-ns = <35>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ sda-gpios = <&pioA PIN_PD4 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&pioA PIN_PD5 GPIO_ACTIVE_HIGH>;
status = "okay";
at24@54 {
@@ -441,18 +450,36 @@
bias-disable;
};
+ pinctrl_flx4_gpio: flx4_gpio {
+ pinmux = <PIN_PD12__GPIO>,
+ <PIN_PD13__GPIO>;
+ bias-pull-up;
+ };
+
pinctrl_i2c0_default: i2c0_default {
pinmux = <PIN_PD21__TWD0>,
<PIN_PD22__TWCK0>;
bias-disable;
};
+ pinctrl_i2c0_gpio: i2c0_gpio {
+ pinmux = <PIN_PD21__GPIO>,
+ <PIN_PD22__GPIO>;
+ bias-pull-up;
+ };
+
pinctrl_i2c1_default: i2c1_default {
pinmux = <PIN_PD4__TWD1>,
<PIN_PD5__TWCK1>;
bias-disable;
};
+ pinctrl_i2c1_gpio: i2c1_gpio {
+ pinmux = <PIN_PD4__GPIO>,
+ <PIN_PD5__GPIO>;
+ bias-pull-up;
+ };
+
pinctrl_i2s0_default: i2s0_default {
pinmux = <PIN_PC1__I2SC0_CK>,
<PIN_PC2__I2SC0_MCK>,
--
2.20.1
WARNING: multiple messages have this Message-ID (diff)
From: <Codrin.Ciubotariu@microchip.com>
To: <linux-i2c@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>
Cc: robh@kernel.org, alexandre.belloni@bootlin.com,
kamel.bouhara@bootlin.com, wsa@the-dreams.de,
Ludovic.Desroches@microchip.com
Subject: [PATCH v2 6/6] ARM: at91/dt: sama5d2: add i2c gpio pinctrl
Date: Fri, 3 Jan 2020 09:49:09 +0000 [thread overview]
Message-ID: <20200103094821.13185-7-codrin.ciubotariu@microchip.com> (raw)
In-Reply-To: <20200103094821.13185-1-codrin.ciubotariu@microchip.com>
From: Kamel Bouhara <kamel.bouhara@bootlin.com>
Add the i2c gpio pinctrls to support the i2c bus recovery
Signed-off-by: Kamel Bouhara <kamel.bouhara@bootlin.com>
---
Changes in v2:
- new changes;
arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts | 33 +++++++++++++++++++--
arch/arm/boot/dts/at91-sama5d2_xplained.dts | 33 +++++++++++++++++++--
2 files changed, 60 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts b/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
index ba7f3e646c26..b3cd651ecda0 100644
--- a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
@@ -180,8 +180,11 @@
i2c0: i2c@f8028000 {
dmas = <0>, <0>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c0_default>;
+ pinctrl-1 = <&pinctrl_i2c0_gpio>;
+ sda-gpios = <&pioA PIN_PD21 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&pioA PIN_PD22 GPIO_ACTIVE_HIGH>;
status = "okay";
};
@@ -198,8 +201,11 @@
#address-cells = <1>;
#size-cells = <0>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_flx0_default>;
+ pinctrl-1 = <&pinctrl_flx0_gpio>;
+ sda-gpios = <&pioA PIN_PB28 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&pioA PIN_PB29 GPIO_ACTIVE_HIGH>;
atmel,fifo-size = <16>;
status = "okay";
};
@@ -226,8 +232,11 @@
i2c1: i2c@fc028000 {
dmas = <0>, <0>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1_default>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ sda-gpios = <&pioA PIN_PC6 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&pioA PIN_PC7 GPIO_ACTIVE_HIGH>;
status = "okay";
at24@50 {
@@ -244,18 +253,36 @@
bias-disable;
};
+ pinctrl_flx0_gpio: flx0_gpio {
+ pinmux = <PIN_PB28__GPIO>,
+ <PIN_PB29__GPIO>;
+ bias-pull-up;
+ };
+
pinctrl_i2c0_default: i2c0_default {
pinmux = <PIN_PD21__TWD0>,
<PIN_PD22__TWCK0>;
bias-disable;
};
+ pinctrl_i2c0_gpio: i2c0_gpio {
+ pinmux = <PIN_PD21__GPIO>,
+ <PIN_PD22__GPIO>;
+ bias-pull-up;
+ };
+
pinctrl_i2c1_default: i2c1_default {
pinmux = <PIN_PC6__TWD1>,
<PIN_PC7__TWCK1>;
bias-disable;
};
+ pinctrl_i2c1_gpio: i2c1_gpio {
+ pinmux = <PIN_PC6__GPIO>,
+ <PIN_PC7__GPIO>;
+ bias-pull-up;
+ };
+
pinctrl_key_gpio_default: key_gpio_default {
pinmux = <PIN_PA10__GPIO>;
bias-pull-up;
diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
index 9d0a7fbea725..500e49eeb8cc 100644
--- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
@@ -129,8 +129,11 @@
i2c0: i2c@f8028000 {
dmas = <0>, <0>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c0_default>;
+ pinctrl-1 = <&pinctrl_i2c0_gpio>;
+ sda-gpios = <&pioA PIN_PD21 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&pioA PIN_PD22 GPIO_ACTIVE_HIGH>;
i2c-sda-hold-time-ns = <350>;
status = "okay";
@@ -331,8 +334,11 @@
#address-cells = <1>;
#size-cells = <0>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 23>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_flx4_default>;
+ pinctrl-1 = <&pinctrl_flx4_gpio>;
+ sda-gpios = <&pioA PIN_PD12 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&pioA PIN_PD13 GPIO_ACTIVE_HIGH>;
atmel,fifo-size = <16>;
i2c-analog-filter;
i2c-digital-filter;
@@ -343,11 +349,14 @@
i2c1: i2c@fc028000 {
dmas = <0>, <0>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "gpio";
pinctrl-0 = <&pinctrl_i2c1_default>;
i2c-analog-filter;
i2c-digital-filter;
i2c-digital-filter-width-ns = <35>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ sda-gpios = <&pioA PIN_PD4 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&pioA PIN_PD5 GPIO_ACTIVE_HIGH>;
status = "okay";
at24@54 {
@@ -441,18 +450,36 @@
bias-disable;
};
+ pinctrl_flx4_gpio: flx4_gpio {
+ pinmux = <PIN_PD12__GPIO>,
+ <PIN_PD13__GPIO>;
+ bias-pull-up;
+ };
+
pinctrl_i2c0_default: i2c0_default {
pinmux = <PIN_PD21__TWD0>,
<PIN_PD22__TWCK0>;
bias-disable;
};
+ pinctrl_i2c0_gpio: i2c0_gpio {
+ pinmux = <PIN_PD21__GPIO>,
+ <PIN_PD22__GPIO>;
+ bias-pull-up;
+ };
+
pinctrl_i2c1_default: i2c1_default {
pinmux = <PIN_PD4__TWD1>,
<PIN_PD5__TWCK1>;
bias-disable;
};
+ pinctrl_i2c1_gpio: i2c1_gpio {
+ pinmux = <PIN_PD4__GPIO>,
+ <PIN_PD5__GPIO>;
+ bias-pull-up;
+ };
+
pinctrl_i2s0_default: i2s0_default {
pinmux = <PIN_PC1__I2SC0_CK>,
<PIN_PC2__I2SC0_MCK>,
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2020-01-03 9:49 UTC|newest]
Thread overview: 50+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-01-03 9:49 [PATCH v2 0/6] i2c bus recovery for Microchip SoCs Codrin.Ciubotariu
2020-01-03 9:49 ` Codrin.Ciubotariu
2020-01-03 9:49 ` Codrin.Ciubotariu
2020-01-03 9:49 ` [PATCH v2 1/6] dt-bindings: i2c: at91: document optional bus recovery properties Codrin.Ciubotariu
2020-01-03 9:49 ` Codrin.Ciubotariu
2020-01-03 9:49 ` Codrin.Ciubotariu
2020-01-03 22:29 ` Rob Herring
2020-01-03 22:29 ` Rob Herring
2020-01-03 22:29 ` Rob Herring
2020-01-06 16:34 ` Codrin.Ciubotariu
2020-01-06 16:34 ` Codrin.Ciubotariu
2020-01-06 16:34 ` Codrin.Ciubotariu
2020-01-03 9:49 ` [PATCH v2 2/6] i2c: at91: implement i2c bus recovery Codrin.Ciubotariu
2020-01-03 9:49 ` Codrin.Ciubotariu
2020-01-03 9:49 ` Codrin.Ciubotariu
2020-01-09 7:48 ` Ludovic Desroches
2020-01-09 7:48 ` Ludovic Desroches
2020-01-09 7:48 ` Ludovic Desroches
2020-01-09 10:54 ` Codrin.Ciubotariu
2020-01-09 10:54 ` Codrin.Ciubotariu
2020-01-09 10:54 ` Codrin.Ciubotariu-UWL1GkI3JZL3oGB3hsPCZA
2020-01-03 9:49 ` [PATCH v2 3/6] i2c: at91: Send bus clear command if SCL is down Codrin.Ciubotariu
2020-01-03 9:49 ` Codrin.Ciubotariu
2020-01-03 9:49 ` Codrin.Ciubotariu
2020-01-09 7:47 ` Ludovic Desroches
2020-01-09 7:47 ` Ludovic Desroches
2020-01-09 7:47 ` Ludovic Desroches
2020-01-09 10:58 ` Codrin.Ciubotariu
2020-01-09 10:58 ` Codrin.Ciubotariu
2020-01-09 10:58 ` Codrin.Ciubotariu
2020-01-09 11:05 ` Russell King - ARM Linux admin
2020-01-09 11:05 ` Russell King - ARM Linux admin
2020-01-09 13:29 ` Codrin.Ciubotariu
2020-01-09 13:29 ` Codrin.Ciubotariu
2020-01-09 13:29 ` Codrin.Ciubotariu-UWL1GkI3JZL3oGB3hsPCZA
2020-01-03 9:49 ` [PATCH v2 5/6] ARM: at91/dt: sama5d4: add i2c gpio pinctrl Codrin.Ciubotariu
2020-01-03 9:49 ` Codrin.Ciubotariu
2020-01-03 9:49 ` Codrin.Ciubotariu
2020-01-03 9:49 ` [PATCH v2 4/6] ARM: at91/dt: sama5d3: " Codrin.Ciubotariu
2020-01-03 9:49 ` Codrin.Ciubotariu
2020-01-03 9:49 ` Codrin.Ciubotariu
2020-01-04 22:39 ` Peter Rosin
2020-01-04 22:39 ` Peter Rosin
2020-01-04 22:39 ` Peter Rosin
2020-01-06 16:58 ` Codrin.Ciubotariu
2020-01-06 16:58 ` Codrin.Ciubotariu
2020-01-06 16:58 ` Codrin.Ciubotariu
2020-01-03 9:49 ` Codrin.Ciubotariu [this message]
2020-01-03 9:49 ` [PATCH v2 6/6] ARM: at91/dt: sama5d2: " Codrin.Ciubotariu
2020-01-03 9:49 ` Codrin.Ciubotariu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200103094821.13185-7-codrin.ciubotariu@microchip.com \
--to=codrin.ciubotariu@microchip.com \
--cc=Ludovic.Desroches@microchip.com \
--cc=Nicolas.Ferre@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=devicetree@vger.kernel.org \
--cc=kamel.bouhara@bootlin.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-i2c@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
--cc=wsa@the-dreams.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.