From: Maksim Kiselev <bigunclemax@gmail.com> To: linux-kernel@vger.kernel.org Cc: Maxim Kiselev <bigunclemax@gmail.com>, Vasily Khoruzhick <anarsoul@gmail.com>, Yangtao Li <tiny.windzz@gmail.com>, "Rafael J. Wysocki" <rafael@kernel.org>, Daniel Lezcano <daniel.lezcano@linaro.org>, Amit Kucheria <amitk@kernel.org>, Zhang Rui <rui.zhang@intel.com>, Rob Herring <robh+dt@kernel.org>, Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>, Conor Dooley <conor+dt@kernel.org>, Chen-Yu Tsai <wens@csie.org>, Jernej Skrabec <jernej.skrabec@gmail.com>, Samuel Holland <samuel@sholland.org>, Paul Walmsley <paul.walmsley@sifive.com>, Palmer Dabbelt <palmer@dabbelt.com>, Albert Ou <aou@eecs.berkeley.edu>, Cristian Ciocaltea <cristian.ciocaltea@collabora.com>, linux-pm@vger.kernel.org, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-sunxi@lists.linux.dev, linux-riscv@lists.infradead.org Subject: [PATCH v1 1/3] thermal: sun8i: Add D1/T113s THS controller support Date: Sat, 10 Jun 2023 17:17:32 +0300 [thread overview] Message-ID: <20230610141739.999268-2-bigunclemax@gmail.com> (raw) In-Reply-To: <20230610141739.999268-1-bigunclemax@gmail.com> From: Maxim Kiselev <bigunclemax@gmail.com> This patch adds a thermal sensor controller support for the D1/T113s, which is similar to the one on H6, but with only one sensor and different scale and offset values. Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com> Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com> --- drivers/thermal/sun8i_thermal.c | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c index 793ddce72132..01cc4e130892 100644 --- a/drivers/thermal/sun8i_thermal.c +++ b/drivers/thermal/sun8i_thermal.c @@ -628,6 +628,18 @@ static const struct ths_thermal_chip sun50i_h6_ths = { .calc_temp = sun8i_ths_calc_temp, }; +static const struct ths_thermal_chip sun20i_d1_ths = { + .sensor_num = 1, + .has_bus_clk_reset = true, + .offset = 188552, + .scale = 673, + .temp_data_base = SUN50I_H6_THS_TEMP_DATA, + .calibrate = sun50i_h6_ths_calibrate, + .init = sun50i_h6_thermal_init, + .irq_ack = sun50i_h6_irq_ack, + .calc_temp = sun8i_ths_calc_temp, +}; + static const struct of_device_id of_ths_match[] = { { .compatible = "allwinner,sun8i-a83t-ths", .data = &sun8i_a83t_ths }, { .compatible = "allwinner,sun8i-h3-ths", .data = &sun8i_h3_ths }, @@ -636,6 +648,7 @@ static const struct of_device_id of_ths_match[] = { { .compatible = "allwinner,sun50i-a100-ths", .data = &sun50i_a100_ths }, { .compatible = "allwinner,sun50i-h5-ths", .data = &sun50i_h5_ths }, { .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths }, + { .compatible = "allwinner,sun20i-d1-ths", .data = &sun20i_d1_ths }, { /* sentinel */ }, }; MODULE_DEVICE_TABLE(of, of_ths_match); -- 2.39.2
WARNING: multiple messages have this Message-ID (diff)
From: Maksim Kiselev <bigunclemax@gmail.com> To: linux-kernel@vger.kernel.org Cc: Maxim Kiselev <bigunclemax@gmail.com>, Vasily Khoruzhick <anarsoul@gmail.com>, Yangtao Li <tiny.windzz@gmail.com>, "Rafael J. Wysocki" <rafael@kernel.org>, Daniel Lezcano <daniel.lezcano@linaro.org>, Amit Kucheria <amitk@kernel.org>, Zhang Rui <rui.zhang@intel.com>, Rob Herring <robh+dt@kernel.org>, Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>, Conor Dooley <conor+dt@kernel.org>, Chen-Yu Tsai <wens@csie.org>, Jernej Skrabec <jernej.skrabec@gmail.com>, Samuel Holland <samuel@sholland.org>, Paul Walmsley <paul.walmsley@sifive.com>, Palmer Dabbelt <palmer@dabbelt.com>, Albert Ou <aou@eecs.berkeley.edu>, Cristian Ciocaltea <cristian.ciocaltea@collabora.com>, linux-pm@vger.kernel.org, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-sunxi@lists.linux.dev, linux-riscv@lists.infradead.org Subject: [PATCH v1 1/3] thermal: sun8i: Add D1/T113s THS controller support Date: Sat, 10 Jun 2023 17:17:32 +0300 [thread overview] Message-ID: <20230610141739.999268-2-bigunclemax@gmail.com> (raw) In-Reply-To: <20230610141739.999268-1-bigunclemax@gmail.com> From: Maxim Kiselev <bigunclemax@gmail.com> This patch adds a thermal sensor controller support for the D1/T113s, which is similar to the one on H6, but with only one sensor and different scale and offset values. Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com> Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com> --- drivers/thermal/sun8i_thermal.c | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c index 793ddce72132..01cc4e130892 100644 --- a/drivers/thermal/sun8i_thermal.c +++ b/drivers/thermal/sun8i_thermal.c @@ -628,6 +628,18 @@ static const struct ths_thermal_chip sun50i_h6_ths = { .calc_temp = sun8i_ths_calc_temp, }; +static const struct ths_thermal_chip sun20i_d1_ths = { + .sensor_num = 1, + .has_bus_clk_reset = true, + .offset = 188552, + .scale = 673, + .temp_data_base = SUN50I_H6_THS_TEMP_DATA, + .calibrate = sun50i_h6_ths_calibrate, + .init = sun50i_h6_thermal_init, + .irq_ack = sun50i_h6_irq_ack, + .calc_temp = sun8i_ths_calc_temp, +}; + static const struct of_device_id of_ths_match[] = { { .compatible = "allwinner,sun8i-a83t-ths", .data = &sun8i_a83t_ths }, { .compatible = "allwinner,sun8i-h3-ths", .data = &sun8i_h3_ths }, @@ -636,6 +648,7 @@ static const struct of_device_id of_ths_match[] = { { .compatible = "allwinner,sun50i-a100-ths", .data = &sun50i_a100_ths }, { .compatible = "allwinner,sun50i-h5-ths", .data = &sun50i_h5_ths }, { .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths }, + { .compatible = "allwinner,sun20i-d1-ths", .data = &sun20i_d1_ths }, { /* sentinel */ }, }; MODULE_DEVICE_TABLE(of, of_ths_match); -- 2.39.2 _______________________________________________ linux-riscv mailing list linux-riscv@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-riscv
next prev parent reply other threads:[~2023-06-10 14:18 UTC|newest] Thread overview: 26+ messages / expand[flat|nested] mbox.gz Atom feed top 2023-06-10 14:17 [PATCH v1 0/3] Add D1/T113s thermal sensor controller support Maksim Kiselev 2023-06-10 14:17 ` Maksim Kiselev 2023-06-10 14:17 ` Maksim Kiselev [this message] 2023-06-10 14:17 ` [PATCH v1 1/3] thermal: sun8i: Add D1/T113s THS " Maksim Kiselev 2023-06-10 14:17 ` [PATCH v1 2/3] riscv: dts: allwinner: d1: Add thermal sensor and thermal zone Maksim Kiselev 2023-06-10 14:17 ` Maksim Kiselev 2023-06-10 14:17 ` [PATCH v1 3/3] dt-bindings: thermal: sun8i: Add binding for D1/T113s THS controller Maksim Kiselev 2023-06-10 14:17 ` Maksim Kiselev 2023-06-10 14:52 ` Conor Dooley 2023-06-10 14:52 ` Conor Dooley 2023-06-10 15:30 ` Maxim Kiselev 2023-06-10 15:30 ` Maxim Kiselev 2023-06-10 17:59 ` Conor Dooley 2023-06-10 17:59 ` Conor Dooley 2023-06-10 18:01 ` Conor Dooley 2023-06-10 18:01 ` Conor Dooley 2023-06-10 20:31 ` Maxim Kiselev 2023-06-10 20:31 ` Maxim Kiselev 2023-06-10 22:13 ` Conor Dooley 2023-06-10 22:13 ` Conor Dooley 2023-06-11 7:53 ` Maxim Kiselev 2023-06-11 7:53 ` Maxim Kiselev 2023-06-11 10:18 ` Conor Dooley 2023-06-11 10:18 ` Conor Dooley 2023-06-10 19:04 ` [PATCH v1 0/3] Add D1/T113s thermal sensor controller support Jernej Škrabec 2023-06-10 19:04 ` Jernej Škrabec
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20230610141739.999268-2-bigunclemax@gmail.com \ --to=bigunclemax@gmail.com \ --cc=amitk@kernel.org \ --cc=anarsoul@gmail.com \ --cc=aou@eecs.berkeley.edu \ --cc=conor+dt@kernel.org \ --cc=cristian.ciocaltea@collabora.com \ --cc=daniel.lezcano@linaro.org \ --cc=devicetree@vger.kernel.org \ --cc=jernej.skrabec@gmail.com \ --cc=krzysztof.kozlowski+dt@linaro.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-pm@vger.kernel.org \ --cc=linux-riscv@lists.infradead.org \ --cc=linux-sunxi@lists.linux.dev \ --cc=palmer@dabbelt.com \ --cc=paul.walmsley@sifive.com \ --cc=rafael@kernel.org \ --cc=robh+dt@kernel.org \ --cc=rui.zhang@intel.com \ --cc=samuel@sholland.org \ --cc=tiny.windzz@gmail.com \ --cc=wens@csie.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.