All of lore.kernel.org
 help / color / mirror / Atom feed
From: Ricard Wanderlof <ricard.wanderlof@axis.com>
To: "alsa-devel@alsa-project.org" <alsa-devel@alsa-project.org>,
	Mark Brown <broonie@kernel.org>,
	Liam Girdwood <lgirdwood@gmail.com>
Subject: [PATCH v2] ASoC: ics43432: Add codec driver for InvenSense ICS-43432
Date: Fri, 14 Aug 2015 11:10:10 +0200	[thread overview]
Message-ID: <alpine.DEB.2.02.1508141106040.27635@lnxricardw1.se.axis.com> (raw)


V2: Update after comments from Lars-Peter yesterday: set rate to 
CONTINUOUS and let ALSA figure out the details, also removing hw_params as 
it is then not needed.

Add support for the InvenSense ICS-43432 I2S MEMS microphone.

This is a non-software-configurable MEMS microphone with I2S output.

Signed-off-by: Ricard Wanderlof <ricardw@axis.com>
---
 .../devicetree/bindings/sound/ics43432.txt         |   17 ++++
 .../devicetree/bindings/vendor-prefixes.txt        |    1 +
 sound/soc/codecs/Kconfig                           |    4 +
 sound/soc/codecs/Makefile                          |    2 +
 sound/soc/codecs/ics43432.c                        |  101 ++++++++++++++++++++
 5 files changed, 125 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/sound/ics43432.txt
 create mode 100644 sound/soc/codecs/ics43432.c

diff --git a/Documentation/devicetree/bindings/sound/ics43432.txt b/Documentation/devicetree/bindings/sound/ics43432.txt
new file mode 100644
index 0000000..b02e3a6
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/ics43432.txt
@@ -0,0 +1,17 @@
+Invensense ICS-43432 MEMS microphone with I2S output.
+
+There are no software configuration options for this device, indeed, the only
+host connection is the I2S interface. Apart from requirements on clock
+frequency (460 kHz to 3.379 MHz according to the data sheet) there must be
+64 clock cycles in each stereo output frame; 24 of the 32 available bits
+contain audio data. A hardware pin determines if the device outputs data
+on the left or right channel of the I2S frame.
+
+Required properties:
+  - compatible : Must be "invensense,ics43432"
+
+Example:
+
+	ics43432: ics43432 {
+		compatible = "invensense,ics43432";
+	};
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 8033919..7966637 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -103,6 +103,7 @@ img	Imagination Technologies Ltd.
 innolux	Innolux Corporation
 intel	Intel Corporation
 intercontrol	Inter Control Group
+invensense	InvenSense Inc.
 isee	ISEE 2007 S.L.
 isil	Intersil
 karo	Ka-Ro electronics GmbH
diff --git a/sound/soc/codecs/Kconfig b/sound/soc/codecs/Kconfig
index 061c465..d696c85 100644
--- a/sound/soc/codecs/Kconfig
+++ b/sound/soc/codecs/Kconfig
@@ -62,6 +62,7 @@ config SND_SOC_ALL_CODECS
 	select SND_SOC_BT_SCO
 	select SND_SOC_ES8328_SPI if SPI_MASTER
 	select SND_SOC_ES8328_I2C if I2C
+	select SND_SOC_ICS43432
 	select SND_SOC_ISABELLE if I2C
 	select SND_SOC_JZ4740_CODEC
 	select SND_SOC_LM4857 if I2C
@@ -444,6 +445,9 @@ config SND_SOC_ES8328_SPI
 	tristate
 	select SND_SOC_ES8328
 
+config SND_SOC_ICS43432
+	tristate
+
 config SND_SOC_ISABELLE
         tristate
 
diff --git a/sound/soc/codecs/Makefile b/sound/soc/codecs/Makefile
index abe2d7e..23a2caf 100644
--- a/sound/soc/codecs/Makefile
+++ b/sound/soc/codecs/Makefile
@@ -55,6 +55,7 @@ snd-soc-dmic-objs := dmic.o
 snd-soc-es8328-objs := es8328.o
 snd-soc-es8328-i2c-objs := es8328-i2c.o
 snd-soc-es8328-spi-objs := es8328-spi.o
+snd-soc-ics43432-objs := ics43432.o
 snd-soc-isabelle-objs := isabelle.o
 snd-soc-jz4740-codec-objs := jz4740.o
 snd-soc-l3-objs := l3.o
@@ -240,6 +241,7 @@ obj-$(CONFIG_SND_SOC_DMIC)	+= snd-soc-dmic.o
 obj-$(CONFIG_SND_SOC_ES8328)	+= snd-soc-es8328.o
 obj-$(CONFIG_SND_SOC_ES8328_I2C)+= snd-soc-es8328-i2c.o
 obj-$(CONFIG_SND_SOC_ES8328_SPI)+= snd-soc-es8328-spi.o
+obj-$(CONFIG_SND_SOC_ICS43432)	+= snd-soc-ics43432.o
 obj-$(CONFIG_SND_SOC_ISABELLE)	+= snd-soc-isabelle.o
 obj-$(CONFIG_SND_SOC_JZ4740_CODEC)	+= snd-soc-jz4740-codec.o
 obj-$(CONFIG_SND_SOC_L3)	+= snd-soc-l3.o
diff --git a/sound/soc/codecs/ics43432.c b/sound/soc/codecs/ics43432.c
new file mode 100644
index 0000000..fe0af4a
--- /dev/null
+++ b/sound/soc/codecs/ics43432.c
@@ -0,0 +1,101 @@
+/*
+ * I2S MEMS microphone driver for InvenSense ICS-43432
+ *
+ * - Non configurable.
+ * - I2S interface, 64 BCLs per frame, 32 bits per channel, 24 bit data
+ *
+ * Copyright (c) 2015 Axis Communications AB
+ *
+ * Licensed under GPL2.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <sound/core.h>
+#include <sound/pcm.h>
+#include <sound/pcm_params.h>
+#include <sound/soc.h>
+#include <sound/initval.h>
+#include <sound/tlv.h>
+
+#define ICS43432_RATE_MIN 7190 /* Hz, from data sheet */
+#define ICS43432_RATE_MAX 52800  /* Hz, from data sheet */
+
+static int ics43432_set_dai_fmt(struct snd_soc_dai *dai, unsigned int fmt)
+{
+	switch (fmt & SND_SOC_DAIFMT_INV_MASK) {
+	case SND_SOC_DAIFMT_NB_NF:
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
+	case SND_SOC_DAIFMT_I2S:
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+#define ICS43432_FORMATS (SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S32)
+
+static const struct snd_soc_dai_ops ics43432_dai_ops = {
+	.set_fmt	= ics43432_set_dai_fmt,
+};
+
+static struct snd_soc_dai_driver ics43432_dai = {
+	.name = "ics43432-hifi",
+	.capture = {
+		.stream_name = "Capture",
+		.channels_min = 1,
+		.channels_max = 2,
+		.rate_min = ICS43432_RATE_MIN,
+		.rate_max = ICS43432_RATE_MAX,
+		.rates = SNDRV_PCM_RATE_CONTINUOUS,
+		.formats = ICS43432_FORMATS,
+	},
+	.ops = &ics43432_dai_ops,
+};
+
+static struct snd_soc_codec_driver ics43432_codec_driver = {
+};
+
+static int ics43432_probe(struct platform_device *pdev)
+{
+	return snd_soc_register_codec(&pdev->dev, &ics43432_codec_driver,
+			&ics43432_dai, 1);
+}
+
+static int ics43432_remove(struct platform_device *pdev)
+{
+	snd_soc_unregister_codec(&pdev->dev);
+	return 0;
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id ics43432_ids[] = {
+	{ .compatible = "invensense,ics43432", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, ics43432_dt_ids);
+#endif
+
+static struct platform_driver ics43432_driver = {
+	.driver = {
+		.name = "ics43432",
+		.owner = THIS_MODULE,
+		.of_match_table = of_match_ptr(ics43432_ids),
+	},
+	.probe = ics43432_probe,
+	.remove = ics43432_remove,
+};
+
+module_platform_driver(ics43432_driver);
+
+MODULE_DESCRIPTION("ASoC ICS43432 driver");
+MODULE_AUTHOR("Ricard Wanderlof <ricardw@axis.com>");
+MODULE_LICENSE("GPL2");
-- 
1.7.10.4


-- 
Ricard Wolf Wanderlöf                           ricardw(at)axis.com
Axis Communications AB, Lund, Sweden            www.axis.com
Phone +46 46 272 2016                           Fax +46 46 13 61 30

             reply	other threads:[~2015-08-14  9:10 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-08-14  9:10 Ricard Wanderlof [this message]
2015-08-14 16:07 ` [PATCH v2] ASoC: ics43432: Add codec driver for InvenSense ICS-43432 Mark Brown
2015-08-17  7:09   ` Ricard Wanderlof
2015-08-17  7:48     ` Lars-Peter Clausen
2015-08-17  9:51       ` Ricard Wanderlof
2015-08-17 17:33       ` Mark Brown

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=alpine.DEB.2.02.1508141106040.27635@lnxricardw1.se.axis.com \
    --to=ricard.wanderlof@axis.com \
    --cc=alsa-devel@alsa-project.org \
    --cc=broonie@kernel.org \
    --cc=lgirdwood@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.