From: Luca Weiss <luca@z3ntu.xyz>
To: linux-arm-msm@vger.kernel.org
Cc: ~postmarketos/upstreaming@lists.sr.ht, bartosz.dudziak@snejp.pl,
Luca Weiss <luca@z3ntu.xyz>, Arnd Bergmann <arnd@arndb.de>,
Olof Johansson <olof@lixom.net>,
soc@kernel.org, Rob Herring <robh+dt@kernel.org>,
Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: [PATCH 8/8] ARM: dts: qcom: Add support for LG G Watch R
Date: Sun, 12 Sep 2021 01:27:02 +0200 [thread overview]
Message-ID: <20210911232707.259615-9-luca@z3ntu.xyz> (raw)
Message-ID: <20210911232702.obLzaq2VfgksUJtWGc9BNVjUpbUVQysnRH0V-oa6VKA@z> (raw)
In-Reply-To: <20210911232707.259615-1-luca@z3ntu.xyz>
Add a device tree for the LG G Watch R smartwatch, manufactured by LG
Electronics and based on the msm8226 platform (apq8026).
Currently UART, internal storage, power button and touchscreen are
supported.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/qcom-apq8026-lge-lenok.dts | 237 +++++++++++++++++++
2 files changed, 238 insertions(+)
create mode 100644 arch/arm/boot/dts/qcom-apq8026-lge-lenok.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7e0934180724..8cb859728bd9 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -939,6 +939,7 @@ dtb-$(CONFIG_ARCH_OXNAS) += \
ox810se-wd-mbwe.dtb \
ox820-cloudengines-pogoplug-series-3.dtb
dtb-$(CONFIG_ARCH_QCOM) += \
+ qcom-apq8026-lge-lenok.dtb \
qcom-apq8060-dragonboard.dtb \
qcom-apq8064-cm-qs600.dtb \
qcom-apq8064-ifc6410.dtb \
diff --git a/arch/arm/boot/dts/qcom-apq8026-lge-lenok.dts b/arch/arm/boot/dts/qcom-apq8026-lge-lenok.dts
new file mode 100644
index 000000000000..02c8dfb0988a
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8026-lge-lenok.dts
@@ -0,0 +1,237 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "qcom-pm8226.dtsi"
+
+/ {
+ model = "LG G Watch R";
+ compatible = "lge,lenok", "qcom,apq8026";
+ qcom,board-id = <132 0x0a>;
+ qcom,msm-id = <199 0x20000>;
+
+ aliases {
+ serial0 = &blsp1_uart3;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&blsp1_i2c5 {
+ status = "okay";
+ clock-frequency = <384000>;
+
+ touchscreen@20 {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x20>;
+
+ interrupts-extended = <&tlmm 17 IRQ_TYPE_EDGE_FALLING>;
+ vdd-supply = <&pm8226_l15>;
+ vio-supply = <&pm8226_l22>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&touch_pins>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rmi4-f01@1 {
+ reg = <0x1>;
+ syna,nosleep-mode = <1>;
+ };
+
+ rmi4-f12@12 {
+ reg = <0x12>;
+ syna,sensor-type = <1>;
+ };
+ };
+};
+
+&blsp1_uart3 {
+ status = "okay";
+};
+
+&sdhc_1 {
+ status = "okay";
+
+ vmmc-supply = <&pm8226_l17>;
+ vqmmc-supply = <&pm8226_l6>;
+
+ bus-width = <8>;
+ non-removable;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhc1_pin_a>;
+};
+
+&rpm_requests {
+ pm8226-regulators {
+ compatible = "qcom,rpm-pm8226-regulators";
+
+ pm8226_s1: s1 {
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1275000>;
+ };
+ pm8226_s3: s3 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1350000>;
+ };
+ pm8226_s4: s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2200000>;
+ };
+ pm8226_s5: s5 {
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+ };
+
+ pm8226_l1: l1 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+ pm8226_l2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+ pm8226_l3: l3 {
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1337500>;
+ };
+ pm8226_l4: l4 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+ pm8226_l5: l5 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+ pm8226_l6: l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ pm8226_l7: l7 {
+ regulator-min-microvolt = <1850000>;
+ regulator-max-microvolt = <1850000>;
+ };
+ pm8226_l8: l8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ pm8226_l9: l9 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+ pm8226_l10: l10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ pm8226_l12: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ pm8226_l14: l14 {
+ regulator-min-microvolt = <2750000>;
+ regulator-max-microvolt = <2750000>;
+ };
+ pm8226_l15: l15 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ pm8226_l16: l16 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3350000>;
+ };
+ pm8226_l17: l17 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ };
+ pm8226_l18: l18 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ };
+ pm8226_l19: l19 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+ pm8226_l20: l20 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ };
+ pm8226_l21: l21 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+ pm8226_l22: l22 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ pm8226_l23: l23 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+ pm8226_l24: l24 {
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1350000>;
+ };
+ pm8226_l25: l25 {
+ regulator-min-microvolt = <1775000>;
+ regulator-max-microvolt = <2125000>;
+ };
+ pm8226_l26: l26 {
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+ pm8226_l27: l27 {
+ regulator-min-microvolt = <2050000>;
+ regulator-max-microvolt = <2050000>;
+ };
+ pm8226_l28: l28 {
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ pm8226_lvs1: lvs1 {};
+ };
+};
+
+&tlmm {
+ sdhc1_pin_a: sdhc1-pin-active {
+ clk {
+ pins = "sdc1_clk";
+ drive-strength = <10>;
+ bias-disable;
+ };
+
+ cmd-data {
+ pins = "sdc1_cmd", "sdc1_data";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+ };
+
+ touch_pins: touch {
+ irq {
+ pins = "gpio17";
+ function = "gpio";
+
+ drive-strength = <8>;
+ bias-pull-down;
+ input-enable;
+ };
+
+ reset {
+ pins = "gpio16";
+ function = "gpio";
+
+ drive-strength = <8>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
--
2.33.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
parent reply other threads:[~2021-09-11 23:48 UTC|newest]
Thread overview: expand[flat|nested] mbox.gz Atom feed
[parent not found: <20210911232707.259615-1-luca@z3ntu.xyz>]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210911232707.259615-9-luca@z3ntu.xyz \
--to=luca@z3ntu.xyz \
--cc=agross@kernel.org \
--cc=arnd@arndb.de \
--cc=bartosz.dudziak@snejp.pl \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=olof@lixom.net \
--cc=robh+dt@kernel.org \
--cc=soc@kernel.org \
--cc=~postmarketos/upstreaming@lists.sr.ht \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).