[PATCH 1/4] ARM: dts: exynos: fix roles of USB 3.0 ports on Odroid XU

[PATCH 1/4] ARM: dts: exynos: fix roles of USB 3.0 ports on Odroid XU

[Krzysztof Kozlowski]

On Odroid XU board the USB3-0 port is a microUSB and USB3-1 port is USB
type A (host).  The roles were copied from Odroid XU3 (Exynos5422)
design which has it reversed.

Fixes: 8149afe4dbf9 ("ARM: dts: exynos: Add initial support for Odroid XU board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm/boot/dts/exynos5410-odroidxu.dts | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/exynos5410-odroidxu.dts b/arch/arm/boot/dts/exynos5410-odroidxu.dts
index 4f9297ae0763..353eb6ef3a04 100644
--- a/arch/arm/boot/dts/exynos5410-odroidxu.dts
+++ b/arch/arm/boot/dts/exynos5410-odroidxu.dts
@@ -637,11 +637,11 @@ &tmu_cpu3 {
 };
 
 &usbdrd_dwc3_0 {
-	dr_mode = "host";
+	dr_mode = "peripheral";
 };
 
 &usbdrd_dwc3_1 {
-	dr_mode = "peripheral";
+	dr_mode = "host";
 };
 
 &usbdrd3_0 {
-- 
2.25.1

[PATCH 2/4] ARM: dts: exynos: fix USB 3.0 VBUS control and over-current pins on Exynos5410

[Krzysztof Kozlowski]

The VBUS control (PWREN) and over-current pins of USB 3.0 DWC3
controllers are on Exynos5410 regular GPIOs.  This is different than for
example on Exynos5422 where these are special ETC pins with proper reset
values (pulls, functions).

Therefore these pins should be configured to enable proper USB 3.0
peripheral and host modes.  This also fixes over-current warning:

    [    6.024658] usb usb4-port1: over-current condition
    [    6.028271] usb usb3-port1: over-current condition

Fixes: cb0896562228 ("ARM: dts: exynos: Add USB to Exynos5410")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm/boot/dts/exynos5410-pinctrl.dtsi | 28 +++++++++++++++++++++++
 arch/arm/boot/dts/exynos5410.dtsi         |  4 ++++
 2 files changed, 32 insertions(+)

diff --git a/arch/arm/boot/dts/exynos5410-pinctrl.dtsi b/arch/arm/boot/dts/exynos5410-pinctrl.dtsi
index e5d0a2a4f648..d0aa18443a69 100644
--- a/arch/arm/boot/dts/exynos5410-pinctrl.dtsi
+++ b/arch/arm/boot/dts/exynos5410-pinctrl.dtsi
@@ -560,6 +560,34 @@ gpk3: gpk3 {
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
+
+	usb3_1_oc: usb3-1-oc {
+		samsung,pins = "gpk2-4", "gpk2-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	usb3_1_vbusctrl: usb3-1-vbusctrl {
+		samsung,pins = "gpk2-6", "gpk2-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	usb3_0_oc: usb3-0-oc {
+		samsung,pins = "gpk3-0", "gpk3-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	usb3_0_vbusctrl: usb3-0-vbusctrl {
+		samsung,pins = "gpk3-2", "gpk3-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
 };
 
 &pinctrl_2 {
diff --git a/arch/arm/boot/dts/exynos5410.dtsi b/arch/arm/boot/dts/exynos5410.dtsi
index abe75b9e39f5..060b8696d24d 100644
--- a/arch/arm/boot/dts/exynos5410.dtsi
+++ b/arch/arm/boot/dts/exynos5410.dtsi
@@ -390,6 +390,8 @@ &trng {
 &usbdrd3_0 {
 	clocks = <&clock CLK_USBD300>;
 	clock-names = "usbdrd30";
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb3_0_oc>, <&usb3_0_vbusctrl>;
 };
 
 &usbdrd_phy0 {
@@ -401,6 +403,8 @@ &usbdrd_phy0 {
 &usbdrd3_1 {
 	clocks = <&clock CLK_USBD301>;
 	clock-names = "usbdrd30";
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb3_1_oc>, <&usb3_1_vbusctrl>;
 };
 
 &usbdrd_dwc3_1 {
-- 
2.25.1

[PATCH 3/4] ARM: dts: exynos: fix USB 3.0 pins supply being turned off on Odroid XU

[Krzysztof Kozlowski]

On Odroid XU LDO12 and LDO15 supplies the power to USB 3.0 blocks but
the GPK GPIO pins are supplied by LDO7 (VDDQ_LCD).  LDO7 also supplies
GPJ GPIO pins.

The Exynos pinctrl driver does not take any supplies, so to have entire
GPIO block always available, make the regulator always on.

Fixes: 88644b4c750b ("ARM: dts: exynos: Configure PWM, usb3503, PMIC and thermal on Odroid XU board")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm/boot/dts/exynos5410-odroidxu.dts | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/boot/dts/exynos5410-odroidxu.dts b/arch/arm/boot/dts/exynos5410-odroidxu.dts
index 353eb6ef3a04..6cc4d4653f84 100644
--- a/arch/arm/boot/dts/exynos5410-odroidxu.dts
+++ b/arch/arm/boot/dts/exynos5410-odroidxu.dts
@@ -327,6 +327,8 @@ ldo7_reg: LDO7 {
 				regulator-name = "vddq_lcd";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
+				/* Supplies also GPK and GPJ */
+				regulator-always-on;
 			};
 
 			ldo8_reg: LDO8 {
-- 
2.25.1

Re: [PATCH 1/4] ARM: dts: exynos: fix roles of USB 3.0 ports on Odroid XU

[Krzysztof Kozlowski]

On Thu, Oct 15, 2020 at 08:20:41PM +0200, Krzysztof Kozlowski wrote:
> On Odroid XU board the USB3-0 port is a microUSB and USB3-1 port is USB
> type A (host).  The roles were copied from Odroid XU3 (Exynos5422)
> design which has it reversed.
> 
> Fixes: 8149afe4dbf9 ("ARM: dts: exynos: Add initial support for Odroid XU board")
> Cc: <stable@vger.kernel.org>
> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
> ---
>  arch/arm/boot/dts/exynos5410-odroidxu.dts | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)

Applied all four, with Gabriel's tested-by tag.

Best regards,
Krzysztof