[PATCH 1/3] net: bcmgenet: synchronize EXT_RGMII_OOB_CTRL access

[PATCH 1/3] net: bcmgenet: synchronize EXT_RGMII_OOB_CTRL access

[Doug Berger]

The EXT_RGMII_OOB_CTRL register can be written from different
contexts. It is predominantly written from the adjust_link
handler which is synchronized by the phydev->lock, but can
also be written from a different context when configuring the
mii in bcmgenet_mii_config().

The chances of contention are quite low, but it is conceivable
that adjust_link could occur during resume when WoL is enabled
so use the phydev->lock synchronizer in bcmgenet_mii_config()
to be sure.

Fixes: afe3f907d20f ("net: bcmgenet: power on MII block for all MII modes")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
---
 drivers/net/ethernet/broadcom/genet/bcmmii.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/broadcom/genet/bcmmii.c b/drivers/net/ethernet/broadcom/genet/bcmmii.c
index 9ada89355747..86a4aa72b3d4 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmmii.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmmii.c
@@ -2,7 +2,7 @@
 /*
  * Broadcom GENET MDIO routines
  *
- * Copyright (c) 2014-2017 Broadcom
+ * Copyright (c) 2014-2024 Broadcom
  */
 
 #include <linux/acpi.h>
@@ -275,6 +275,7 @@ int bcmgenet_mii_config(struct net_device *dev, bool init)
 	 * block for the interface to work, unconditionally clear the
 	 * Out-of-band disable since we do not need it.
 	 */
+	mutex_lock(&phydev->lock);
 	reg = bcmgenet_ext_readl(priv, EXT_RGMII_OOB_CTRL);
 	reg &= ~OOB_DISABLE;
 	if (priv->ext_phy) {
@@ -286,6 +287,7 @@ int bcmgenet_mii_config(struct net_device *dev, bool init)
 			reg |= RGMII_MODE_EN;
 	}
 	bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL);
+	mutex_unlock(&phydev->lock);
 
 	if (init)
 		dev_info(kdev, "configuring instance for %s\n", phy_name);
-- 
2.34.1

[PATCH 2/3] net: bcmgenet: synchronize use of bcmgenet_set_rx_mode()

[Doug Berger]

The ndo_set_rx_mode function is synchronized with the
netif_addr_lock spinlock and BHs disabled. Since this
function is also invoked directly from the driver the
same synchronization should be applied.

Fixes: 72f96347628e ("net: bcmgenet: set Rx mode before starting netif")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
---
 drivers/net/ethernet/broadcom/genet/bcmgenet.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
index b1f84b37032a..5452b7dc6e6a 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
@@ -2,7 +2,7 @@
 /*
  * Broadcom GENET (Gigabit Ethernet) controller driver
  *
- * Copyright (c) 2014-2020 Broadcom
+ * Copyright (c) 2014-2024 Broadcom
  */
 
 #define pr_fmt(fmt)				"bcmgenet: " fmt
@@ -3334,7 +3334,9 @@ static void bcmgenet_netif_start(struct net_device *dev)
 	struct bcmgenet_priv *priv = netdev_priv(dev);
 
 	/* Start the network engine */
+	netif_addr_lock_bh(dev);
 	bcmgenet_set_rx_mode(dev);
+	netif_addr_unlock_bh(dev);
 	bcmgenet_enable_rx_napi(priv);
 
 	umac_enable_set(priv, CMD_TX_EN | CMD_RX_EN, true);
-- 
2.34.1

[PATCH 3/3] net: bcmgenet: synchronize UMAC_CMD access

[Doug Berger]

The UMAC_CMD register is written from different execution
contexts and has insufficient synchronization protections to
prevent possible corruption. Of particular concern are the
acceses from the phy_device delayed work context used by the
adjust_link call and the BH context that may be used by the
ndo_set_rx_mode call.

A spinlock is added to the driver to protect contended register
accesses (i.e. reg_lock) and it is used to synchronize accesses
to UMAC_CMD.

Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
---
 drivers/net/ethernet/broadcom/genet/bcmgenet.c     | 12 +++++++++++-
 drivers/net/ethernet/broadcom/genet/bcmgenet.h     |  4 +++-
 drivers/net/ethernet/broadcom/genet/bcmgenet_wol.c |  8 +++++++-
 drivers/net/ethernet/broadcom/genet/bcmmii.c       |  2 ++
 4 files changed, 23 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
index 5452b7dc6e6a..c7e7dac057a3 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
@@ -2467,14 +2467,18 @@ static void umac_enable_set(struct bcmgenet_priv *priv, u32 mask, bool enable)
 {
 	u32 reg;
 
+	spin_lock_bh(&priv->reg_lock);
 	reg = bcmgenet_umac_readl(priv, UMAC_CMD);
-	if (reg & CMD_SW_RESET)
+	if (reg & CMD_SW_RESET) {
+		spin_unlock_bh(&priv->reg_lock);
 		return;
+	}
 	if (enable)
 		reg |= mask;
 	else
 		reg &= ~mask;
 	bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+	spin_unlock_bh(&priv->reg_lock);
 
 	/* UniMAC stops on a packet boundary, wait for a full-size packet
 	 * to be processed
@@ -2490,8 +2494,10 @@ static void reset_umac(struct bcmgenet_priv *priv)
 	udelay(10);
 
 	/* issue soft reset and disable MAC while updating its registers */
+	spin_lock_bh(&priv->reg_lock);
 	bcmgenet_umac_writel(priv, CMD_SW_RESET, UMAC_CMD);
 	udelay(2);
+	spin_unlock_bh(&priv->reg_lock);
 }
 
 static void bcmgenet_intr_disable(struct bcmgenet_priv *priv)
@@ -3597,16 +3603,19 @@ static void bcmgenet_set_rx_mode(struct net_device *dev)
 	 * 3. The number of filters needed exceeds the number filters
 	 *    supported by the hardware.
 	*/
+	spin_lock(&priv->reg_lock);
 	reg = bcmgenet_umac_readl(priv, UMAC_CMD);
 	if ((dev->flags & (IFF_PROMISC | IFF_ALLMULTI)) ||
 	    (nfilter > MAX_MDF_FILTER)) {
 		reg |= CMD_PROMISC;
 		bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+		spin_unlock(&priv->reg_lock);
 		bcmgenet_umac_writel(priv, 0, UMAC_MDF_CTRL);
 		return;
 	} else {
 		reg &= ~CMD_PROMISC;
 		bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+		spin_unlock(&priv->reg_lock);
 	}
 
 	/* update MDF filter */
@@ -4005,6 +4014,7 @@ static int bcmgenet_probe(struct platform_device *pdev)
 		goto err;
 	}
 
+	spin_lock_init(&priv->reg_lock);
 	spin_lock_init(&priv->lock);
 
 	/* Set default pause parameters */
diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.h b/drivers/net/ethernet/broadcom/genet/bcmgenet.h
index 7523b60b3c1c..43b923c48b14 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.h
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.h
@@ -1,6 +1,6 @@
 /* SPDX-License-Identifier: GPL-2.0-only */
 /*
- * Copyright (c) 2014-2020 Broadcom
+ * Copyright (c) 2014-2024 Broadcom
  */
 
 #ifndef __BCMGENET_H__
@@ -573,6 +573,8 @@ struct bcmgenet_rxnfc_rule {
 /* device context */
 struct bcmgenet_priv {
 	void __iomem *base;
+	/* reg_lock: lock to serialize access to shared registers */
+	spinlock_t reg_lock;
 	enum bcmgenet_version version;
 	struct net_device *dev;
 
diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet_wol.c b/drivers/net/ethernet/broadcom/genet/bcmgenet_wol.c
index 7a41cad5788f..1248792d7fd4 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet_wol.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet_wol.c
@@ -2,7 +2,7 @@
 /*
  * Broadcom GENET (Gigabit Ethernet) Wake-on-LAN support
  *
- * Copyright (c) 2014-2020 Broadcom
+ * Copyright (c) 2014-2024 Broadcom
  */
 
 #define pr_fmt(fmt)				"bcmgenet_wol: " fmt
@@ -151,6 +151,7 @@ int bcmgenet_wol_power_down_cfg(struct bcmgenet_priv *priv,
 	}
 
 	/* Can't suspend with WoL if MAC is still in reset */
+	spin_lock_bh(&priv->reg_lock);
 	reg = bcmgenet_umac_readl(priv, UMAC_CMD);
 	if (reg & CMD_SW_RESET)
 		reg &= ~CMD_SW_RESET;
@@ -158,6 +159,7 @@ int bcmgenet_wol_power_down_cfg(struct bcmgenet_priv *priv,
 	/* disable RX */
 	reg &= ~CMD_RX_EN;
 	bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+	spin_unlock_bh(&priv->reg_lock);
 	mdelay(10);
 
 	if (priv->wolopts & (WAKE_MAGIC | WAKE_MAGICSECURE)) {
@@ -203,6 +205,7 @@ int bcmgenet_wol_power_down_cfg(struct bcmgenet_priv *priv,
 	}
 
 	/* Enable CRC forward */
+	spin_lock_bh(&priv->reg_lock);
 	reg = bcmgenet_umac_readl(priv, UMAC_CMD);
 	priv->crc_fwd_en = 1;
 	reg |= CMD_CRC_FWD;
@@ -210,6 +213,7 @@ int bcmgenet_wol_power_down_cfg(struct bcmgenet_priv *priv,
 	/* Receiver must be enabled for WOL MP detection */
 	reg |= CMD_RX_EN;
 	bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+	spin_unlock_bh(&priv->reg_lock);
 
 	reg = UMAC_IRQ_MPD_R;
 	if (hfb_enable)
@@ -256,7 +260,9 @@ void bcmgenet_wol_power_up_cfg(struct bcmgenet_priv *priv,
 	}
 
 	/* Disable CRC Forward */
+	spin_lock_bh(&priv->reg_lock);
 	reg = bcmgenet_umac_readl(priv, UMAC_CMD);
 	reg &= ~CMD_CRC_FWD;
 	bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+	spin_unlock_bh(&priv->reg_lock);
 }
diff --git a/drivers/net/ethernet/broadcom/genet/bcmmii.c b/drivers/net/ethernet/broadcom/genet/bcmmii.c
index 86a4aa72b3d4..c4a3698cef66 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmmii.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmmii.c
@@ -76,6 +76,7 @@ static void bcmgenet_mac_config(struct net_device *dev)
 	reg |= RGMII_LINK;
 	bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL);
 
+	spin_lock_bh(&priv->reg_lock);
 	reg = bcmgenet_umac_readl(priv, UMAC_CMD);
 	reg &= ~((CMD_SPEED_MASK << CMD_SPEED_SHIFT) |
 		       CMD_HD_EN |
@@ -88,6 +89,7 @@ static void bcmgenet_mac_config(struct net_device *dev)
 		reg |= CMD_TX_EN | CMD_RX_EN;
 	}
 	bcmgenet_umac_writel(priv, reg, UMAC_CMD);
+	spin_unlock_bh(&priv->reg_lock);
 
 	active = phy_init_eee(phydev, 0) >= 0;
 	bcmgenet_eee_enable_set(dev,
-- 
2.34.1

Re: [PATCH 1/3] net: bcmgenet: synchronize EXT_RGMII_OOB_CTRL access

[Simon Horman]

On Thu, Apr 25, 2024 at 03:10:05PM -0700, Doug Berger wrote:
> The EXT_RGMII_OOB_CTRL register can be written from different
> contexts. It is predominantly written from the adjust_link
> handler which is synchronized by the phydev->lock, but can
> also be written from a different context when configuring the
> mii in bcmgenet_mii_config().
> 
> The chances of contention are quite low, but it is conceivable
> that adjust_link could occur during resume when WoL is enabled
> so use the phydev->lock synchronizer in bcmgenet_mii_config()
> to be sure.
> 
> Fixes: afe3f907d20f ("net: bcmgenet: power on MII block for all MII modes")
> Cc: stable@vger.kernel.org
> Signed-off-by: Doug Berger <opendmb@gmail.com>

Reviewed-by: Simon Horman <horms@kernel.org>

Re: [PATCH 2/3] net: bcmgenet: synchronize use of bcmgenet_set_rx_mode()

[Simon Horman]

On Thu, Apr 25, 2024 at 03:10:06PM -0700, Doug Berger wrote:
> The ndo_set_rx_mode function is synchronized with the
> netif_addr_lock spinlock and BHs disabled. Since this
> function is also invoked directly from the driver the
> same synchronization should be applied.
> 
> Fixes: 72f96347628e ("net: bcmgenet: set Rx mode before starting netif")
> Cc: stable@vger.kernel.org
> Signed-off-by: Doug Berger <opendmb@gmail.com>

Reviewed-by: Simon Horman <horms@kernel.org>

Re: [PATCH 3/3] net: bcmgenet: synchronize UMAC_CMD access

[Simon Horman]

On Thu, Apr 25, 2024 at 03:10:07PM -0700, Doug Berger wrote:
> The UMAC_CMD register is written from different execution
> contexts and has insufficient synchronization protections to
> prevent possible corruption. Of particular concern are the
> acceses from the phy_device delayed work context used by the
> adjust_link call and the BH context that may be used by the
> ndo_set_rx_mode call.
> 
> A spinlock is added to the driver to protect contended register
> accesses (i.e. reg_lock) and it is used to synchronize accesses
> to UMAC_CMD.
> 
> Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
> Cc: stable@vger.kernel.org
> Signed-off-by: Doug Berger <opendmb@gmail.com>

Reviewed-by: Simon Horman <horms@kernel.org>

[PATCH 1/3] net: bcmgenet: synchronize EXT_RGMII_OOB_CTRL access

[Doug Berger]

The EXT_RGMII_OOB_CTRL register can be written from different
contexts. It is predominantly written from the adjust_link
handler which is synchronized by the phydev->lock, but can
also be written from a different context when configuring the
mii in bcmgenet_mii_config().

The chances of contention are quite low, but it is conceivable
that adjust_link could occur during resume when WoL is enabled
so use the phydev->lock synchronizer in bcmgenet_mii_config()
to be sure.

Fixes: afe3f907d20f ("net: bcmgenet: power on MII block for all MII modes")
Cc: stable@vger.kernel.org
Signed-off-by: Doug Berger <opendmb@gmail.com>
---
 drivers/net/ethernet/broadcom/genet/bcmmii.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/broadcom/genet/bcmmii.c b/drivers/net/ethernet/broadcom/genet/bcmmii.c
index 9ada89355747..86a4aa72b3d4 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmmii.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmmii.c
@@ -2,7 +2,7 @@
 /*
  * Broadcom GENET MDIO routines
  *
- * Copyright (c) 2014-2017 Broadcom
+ * Copyright (c) 2014-2024 Broadcom
  */
 
 #include <linux/acpi.h>
@@ -275,6 +275,7 @@ int bcmgenet_mii_config(struct net_device *dev, bool init)
 	 * block for the interface to work, unconditionally clear the
 	 * Out-of-band disable since we do not need it.
 	 */
+	mutex_lock(&phydev->lock);
 	reg = bcmgenet_ext_readl(priv, EXT_RGMII_OOB_CTRL);
 	reg &= ~OOB_DISABLE;
 	if (priv->ext_phy) {
@@ -286,6 +287,7 @@ int bcmgenet_mii_config(struct net_device *dev, bool init)
 			reg |= RGMII_MODE_EN;
 	}
 	bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL);
+	mutex_unlock(&phydev->lock);
 
 	if (init)
 		dev_info(kdev, "configuring instance for %s\n", phy_name);
-- 
2.34.1