[PATCH v7,3/4] drm/mediatek: keep dsi as LP00 before dcs cmds transfer

[PATCH v7,3/4] drm/mediatek: keep dsi as LP00 before dcs cmds transfer

[xinlei.lee]

From: Jitao Shi <jitao.shi@mediatek.com>

To comply with the panel sequence, hold the mipi signal to LP00 before the dcs cmds transmission,
and pull the mipi signal high from LP00 to LP11 until the start of the dcs cmds transmission.
The normal panel timing is :
(1) pp1800 DC pull up
(2) avdd & avee AC pull high
(3) lcm_reset pull high -> pull low -> pull high
(4) Pull MIPI signal high (LP11) -> initial code -> send video data(HS mode)
The power-off sequence is reversed.
If dsi is not in cmd mode, then dsi will pull the mipi signal high in the mtk_output_dsi_enable function.
The delay in lane_ready func is the reaction time of dsi_rx after pulling up the mipi signal.

Fixes: 2dd8075d2185 ("drm/mediatek: mtk_dsi: Use the drm_panel_bridge API")

Cc: <stable@vger.kernel.org> # 5.10.x: b255d51e3967: sched: Modify dsi funcs to atomic operations
Cc: <stable@vger.kernel.org> # 5.10.x: 72c69c977502: sched: Separate poweron/poweroff from enable/disable and define new funcs
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
 drivers/gpu/drm/mediatek/mtk_dsi.c | 28 +++++++++++++++++++++-------
 1 file changed, 21 insertions(+), 7 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c b/drivers/gpu/drm/mediatek/mtk_dsi.c
index d9a6b928dba8..25e84d9426bf 100644
--- a/drivers/gpu/drm/mediatek/mtk_dsi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dsi.c
@@ -203,6 +203,7 @@ struct mtk_dsi {
 	struct mtk_phy_timing phy_timing;
 	int refcount;
 	bool enabled;
+	bool lanes_ready;
 	u32 irq_data;
 	wait_queue_head_t irq_wait_queue;
 	const struct mtk_dsi_driver_data *driver_data;
@@ -661,18 +662,11 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi)
 	mtk_dsi_reset_engine(dsi);
 	mtk_dsi_phy_timconfig(dsi);
 
-	mtk_dsi_rxtx_control(dsi);
-	usleep_range(30, 100);
-	mtk_dsi_reset_dphy(dsi);
 	mtk_dsi_ps_control_vact(dsi);
 	mtk_dsi_set_vm_cmd(dsi);
 	mtk_dsi_config_vdo_timing(dsi);
 	mtk_dsi_set_interrupt_enable(dsi);
 
-	mtk_dsi_clk_ulp_mode_leave(dsi);
-	mtk_dsi_lane0_ulp_mode_leave(dsi);
-	mtk_dsi_clk_hs_mode(dsi, 0);
-
 	return 0;
 err_disable_engine_clk:
 	clk_disable_unprepare(dsi->engine_clk);
@@ -701,6 +695,23 @@ static void mtk_dsi_poweroff(struct mtk_dsi *dsi)
 	clk_disable_unprepare(dsi->digital_clk);
 
 	phy_power_off(dsi->phy);
+
+	dsi->lanes_ready = false;
+}
+
+static void mtk_dsi_lane_ready(struct mtk_dsi *dsi)
+{
+	if (!dsi->lanes_ready) {
+		dsi->lanes_ready = true;
+		mtk_dsi_rxtx_control(dsi);
+		usleep_range(30, 100);
+		mtk_dsi_reset_dphy(dsi);
+		mtk_dsi_clk_ulp_mode_leave(dsi);
+		mtk_dsi_lane0_ulp_mode_leave(dsi);
+		mtk_dsi_clk_hs_mode(dsi, 0);
+		msleep(20);
+		/* The reaction time after pulling up the mipi signal for dsi_rx */
+	}
 }
 
 static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
@@ -708,6 +719,7 @@ static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
 	if (dsi->enabled)
 		return;
 
+	mtk_dsi_lane_ready(dsi);
 	mtk_dsi_set_mode(dsi);
 	mtk_dsi_clk_hs_mode(dsi, 1);
 
@@ -1017,6 +1029,8 @@ static ssize_t mtk_dsi_host_transfer(struct mipi_dsi_host *host,
 	if (MTK_DSI_HOST_IS_READ(msg->type))
 		irq_flag |= LPRX_RD_RDY_INT_FLAG;
 
+	mtk_dsi_lane_ready(dsi);
+
 	ret = mtk_dsi_host_send_cmd(dsi, msg, irq_flag);
 	if (ret)
 		goto restore_dsi_mode;
-- 
2.18.0

Re: [PATCH v7,3/4] drm/mediatek: keep dsi as LP00 before dcs cmds transfer

[Rex-BC Chen]

On Fri, 2022-05-20 at 10:00 +0800, xinlei.lee@mediatek.com wrote:
> From: Jitao Shi <jitao.shi@mediatek.com>
> 
> To comply with the panel sequence, hold the mipi signal to LP00
> before the dcs cmds transmission,
> and pull the mipi signal high from LP00 to LP11 until the start of
> the dcs cmds transmission.
> The normal panel timing is :
> (1) pp1800 DC pull up
> (2) avdd & avee AC pull high
> (3) lcm_reset pull high -> pull low -> pull high
> (4) Pull MIPI signal high (LP11) -> initial code -> send video
> data(HS mode)
> The power-off sequence is reversed.
> If dsi is not in cmd mode, then dsi will pull the mipi signal high in
> the mtk_output_dsi_enable function.
> The delay in lane_ready func is the reaction time of dsi_rx after
> pulling up the mipi signal.
> 
> Fixes: 2dd8075d2185 ("drm/mediatek: mtk_dsi: Use the drm_panel_bridge
> API")
> 
> Cc: <stable@vger.kernel.org> # 5.10.x: b255d51e3967: sched: Modify
> dsi funcs to atomic operations
> Cc: <stable@vger.kernel.org> # 5.10.x: 72c69c977502: sched: Separate
> poweron/poweroff from enable/disable and define new funcs
> Cc: <stable@vger.kernel.org> # 5.10.x
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
> Reviewed-by: AngeloGioacchino Del Regno <
> angelogioacchino.delregno@collabora.com>
> ---

Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>

Re: [PATCH v7, 3/4] drm/mediatek: keep dsi as LP00 before dcs cmds transfer

[CK Hu]

Hi, Xinlei:

On Fri, 2022-05-20 at 10:00 +0800, xinlei.lee@mediatek.com wrote:
> From: Jitao Shi <jitao.shi@mediatek.com>
> 
> To comply with the panel sequence, hold the mipi signal to LP00
> before the dcs cmds transmission,
> and pull the mipi signal high from LP00 to LP11 until the start of
> the dcs cmds transmission.
> The normal panel timing is :
> (1) pp1800 DC pull up
> (2) avdd & avee AC pull high
> (3) lcm_reset pull high -> pull low -> pull high
> (4) Pull MIPI signal high (LP11) -> initial code -> send video
> data(HS mode)
> The power-off sequence is reversed.
> If dsi is not in cmd mode, then dsi will pull the mipi signal high in
> the mtk_output_dsi_enable function.
> The delay in lane_ready func is the reaction time of dsi_rx after
> pulling up the mipi signal.

Reviewed-by: CK Hu <ck.hu@mediatek.com>

> 
> Fixes: 2dd8075d2185 ("drm/mediatek: mtk_dsi: Use the drm_panel_bridge
> API")
> 
> Cc: <stable@vger.kernel.org> # 5.10.x: b255d51e3967: sched: Modify
> dsi funcs to atomic operations
> Cc: <stable@vger.kernel.org> # 5.10.x: 72c69c977502: sched: Separate
> poweron/poweroff from enable/disable and define new funcs
> Cc: <stable@vger.kernel.org> # 5.10.x
> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
> Reviewed-by: AngeloGioacchino Del Regno <
> angelogioacchino.delregno@collabora.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_dsi.c | 28 +++++++++++++++++++++-------
>  1 file changed, 21 insertions(+), 7 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c
> b/drivers/gpu/drm/mediatek/mtk_dsi.c
> index d9a6b928dba8..25e84d9426bf 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dsi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dsi.c
> @@ -203,6 +203,7 @@ struct mtk_dsi {
>  	struct mtk_phy_timing phy_timing;
>  	int refcount;
>  	bool enabled;
> +	bool lanes_ready;
>  	u32 irq_data;
>  	wait_queue_head_t irq_wait_queue;
>  	const struct mtk_dsi_driver_data *driver_data;
> @@ -661,18 +662,11 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi)
>  	mtk_dsi_reset_engine(dsi);
>  	mtk_dsi_phy_timconfig(dsi);
>  
> -	mtk_dsi_rxtx_control(dsi);
> -	usleep_range(30, 100);
> -	mtk_dsi_reset_dphy(dsi);
>  	mtk_dsi_ps_control_vact(dsi);
>  	mtk_dsi_set_vm_cmd(dsi);
>  	mtk_dsi_config_vdo_timing(dsi);
>  	mtk_dsi_set_interrupt_enable(dsi);
>  
> -	mtk_dsi_clk_ulp_mode_leave(dsi);
> -	mtk_dsi_lane0_ulp_mode_leave(dsi);
> -	mtk_dsi_clk_hs_mode(dsi, 0);
> -
>  	return 0;
>  err_disable_engine_clk:
>  	clk_disable_unprepare(dsi->engine_clk);
> @@ -701,6 +695,23 @@ static void mtk_dsi_poweroff(struct mtk_dsi
> *dsi)
>  	clk_disable_unprepare(dsi->digital_clk);
>  
>  	phy_power_off(dsi->phy);
> +
> +	dsi->lanes_ready = false;
> +}
> +
> +static void mtk_dsi_lane_ready(struct mtk_dsi *dsi)
> +{
> +	if (!dsi->lanes_ready) {
> +		dsi->lanes_ready = true;
> +		mtk_dsi_rxtx_control(dsi);
> +		usleep_range(30, 100);
> +		mtk_dsi_reset_dphy(dsi);
> +		mtk_dsi_clk_ulp_mode_leave(dsi);
> +		mtk_dsi_lane0_ulp_mode_leave(dsi);
> +		mtk_dsi_clk_hs_mode(dsi, 0);
> +		msleep(20);
> +		/* The reaction time after pulling up the mipi signal
> for dsi_rx */
> +	}
>  }
>  
>  static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
> @@ -708,6 +719,7 @@ static void mtk_output_dsi_enable(struct mtk_dsi
> *dsi)
>  	if (dsi->enabled)
>  		return;
>  
> +	mtk_dsi_lane_ready(dsi);
>  	mtk_dsi_set_mode(dsi);
>  	mtk_dsi_clk_hs_mode(dsi, 1);
>  
> @@ -1017,6 +1029,8 @@ static ssize_t mtk_dsi_host_transfer(struct
> mipi_dsi_host *host,
>  	if (MTK_DSI_HOST_IS_READ(msg->type))
>  		irq_flag |= LPRX_RD_RDY_INT_FLAG;
>  
> +	mtk_dsi_lane_ready(dsi);
> +
>  	ret = mtk_dsi_host_send_cmd(dsi, msg, irq_flag);
>  	if (ret)
>  		goto restore_dsi_mode;