* [PATCH v2 0/6] arm: mvebu: Support for 98DX25xx/98DX35xx (AlleyCat5)
@ 2022-09-20 8:31 Chris Packham
2022-09-20 8:31 ` [PATCH v2 1/6] net: mvneta: Add support for AlleyCat5 Chris Packham
` (5 more replies)
0 siblings, 6 replies; 17+ messages in thread
From: Chris Packham @ 2022-09-20 8:31 UTC (permalink / raw)
To: Stefan Roese
Cc: Elad Nachman, Vadym Kochan, Chris Packham, Adam Ford, Alice Guo,
Andre Przywara, Chris Packham, Christian Hewitt, Jim Liu,
Joe Hershberger, Keerthy, Lukasz Majewski, Marcel Ziswiler,
Marek Behún, Marek Vasut, Michael Scott, Michael Walle,
Pali Rohár, Peng Fan, Ramon Fried, Samuel Holland,
Sean Anderson, Simon Glass, Tom Rini, Weijie Gao, Ye Li,
Ying-Chun Liu (PaulLiu),
u-boot
These patches are based on Marvell's bootloader for the AlleyCat5/5X
which was based on u-boot 2018.03. I've split that code into consumable
chunks and dropped as much unnecessary stuff as I can. I've also tried
to sync the device trees as much as possible with the support that will
land in Linux 6.0 although there are still some differences
Changes in v2:
- Use distro boot by default
- remove unnecessary SPI-NOR partitions
Chris Packham (6):
net: mvneta: Add support for AlleyCat5
usb: ehci: ehci-marvell: Support for marvell,ac5-ehci
pinctrl: mvebu: Add AlleyCat5 support
misc: mvebu: Add sample at reset driver
arm: mvebu: Support for 98DX25xx/98DX35xx SoC
arm: mvebu: Add RD-AC5X board
arch/arm/dts/Makefile | 3 +-
arch/arm/dts/ac5-98dx25xx.dtsi | 292 +++++++++++++++++++++
arch/arm/dts/ac5-98dx35xx-rd.dts | 140 ++++++++++
arch/arm/dts/ac5-98dx35xx.dtsi | 17 ++
arch/arm/mach-mvebu/Kconfig | 14 +-
arch/arm/mach-mvebu/Makefile | 1 +
arch/arm/mach-mvebu/alleycat5/Makefile | 9 +
arch/arm/mach-mvebu/alleycat5/clock.c | 49 ++++
arch/arm/mach-mvebu/alleycat5/cpu.c | 129 +++++++++
arch/arm/mach-mvebu/alleycat5/soc.c | 229 ++++++++++++++++
arch/arm/mach-mvebu/arm64-common.c | 15 ++
arch/arm/mach-mvebu/include/mach/clock.h | 11 +
arch/arm/mach-mvebu/include/mach/cpu.h | 4 +
arch/arm/mach-mvebu/include/mach/soc.h | 4 +
board/Marvell/mvebu_alleycat-5/MAINTAINERS | 6 +
board/Marvell/mvebu_alleycat-5/Makefile | 3 +
board/Marvell/mvebu_alleycat-5/board.c | 35 +++
configs/mvebu_ac5_rd_defconfig | 88 +++++++
drivers/misc/Kconfig | 6 +
drivers/misc/Makefile | 1 +
drivers/misc/mvebu_sar/Makefile | 4 +
drivers/misc/mvebu_sar/ac5_sar.c | 119 +++++++++
drivers/misc/mvebu_sar/sar-uclass.c | 146 +++++++++++
drivers/net/Kconfig | 2 +-
drivers/net/mvneta.c | 66 ++++-
drivers/pinctrl/mvebu/Kconfig | 2 +-
drivers/usb/host/Kconfig | 1 +
drivers/usb/host/ehci-marvell.c | 57 +++-
include/configs/mvebu_alleycat-5.h | 71 +++++
include/dm/uclass-id.h | 1 +
include/fdtdec.h | 4 +
include/mvebu/mvebu_chip_sar.h | 73 ++++++
include/mvebu/sar.h | 57 ++++
include/mvebu/var.h | 28 ++
include/sar-uclass.h | 23 ++
lib/fdtdec.c | 6 +-
36 files changed, 1698 insertions(+), 18 deletions(-)
create mode 100644 arch/arm/dts/ac5-98dx25xx.dtsi
create mode 100644 arch/arm/dts/ac5-98dx35xx-rd.dts
create mode 100644 arch/arm/dts/ac5-98dx35xx.dtsi
create mode 100644 arch/arm/mach-mvebu/alleycat5/Makefile
create mode 100644 arch/arm/mach-mvebu/alleycat5/clock.c
create mode 100644 arch/arm/mach-mvebu/alleycat5/cpu.c
create mode 100644 arch/arm/mach-mvebu/alleycat5/soc.c
create mode 100644 arch/arm/mach-mvebu/include/mach/clock.h
create mode 100644 board/Marvell/mvebu_alleycat-5/MAINTAINERS
create mode 100644 board/Marvell/mvebu_alleycat-5/Makefile
create mode 100644 board/Marvell/mvebu_alleycat-5/board.c
create mode 100644 configs/mvebu_ac5_rd_defconfig
create mode 100644 drivers/misc/mvebu_sar/Makefile
create mode 100644 drivers/misc/mvebu_sar/ac5_sar.c
create mode 100644 drivers/misc/mvebu_sar/sar-uclass.c
create mode 100644 include/configs/mvebu_alleycat-5.h
create mode 100644 include/mvebu/mvebu_chip_sar.h
create mode 100644 include/mvebu/sar.h
create mode 100644 include/mvebu/var.h
create mode 100644 include/sar-uclass.h
--
2.37.3
^ permalink raw reply [flat|nested] 17+ messages in thread
* [PATCH v2 1/6] net: mvneta: Add support for AlleyCat5
2022-09-20 8:31 [PATCH v2 0/6] arm: mvebu: Support for 98DX25xx/98DX35xx (AlleyCat5) Chris Packham
@ 2022-09-20 8:31 ` Chris Packham
2022-09-20 9:17 ` Stefan Roese
2022-09-20 10:48 ` Pali Rohár
2022-09-20 8:31 ` [PATCH v2 2/6] usb: ehci: ehci-marvell: Support for marvell,ac5-ehci Chris Packham
` (4 subsequent siblings)
5 siblings, 2 replies; 17+ messages in thread
From: Chris Packham @ 2022-09-20 8:31 UTC (permalink / raw)
To: Stefan Roese
Cc: Elad Nachman, Vadym Kochan, Chris Packham, Joe Hershberger,
Ramon Fried, u-boot
Add support for the AlleyCat5 SoC. This lacks the mbus from the other
users of the mvneta.c driver so a new compatible string is needed to
allow for a different window configuration.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
---
(no changes since v1)
drivers/net/Kconfig | 2 +-
drivers/net/mvneta.c | 66 ++++++++++++++++++++++++++++++++++++++++++--
2 files changed, 64 insertions(+), 4 deletions(-)
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 6bbbadc5ee..8df3dce6df 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -448,7 +448,7 @@ config MVGBE
config MVNETA
bool "Marvell Armada XP/385/3700 network interface support"
- depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
+ depends on ARMADA_XP || ARMADA_38X || ARMADA_3700 || ALLEYCAT_5
select PHYLIB
select DM_MDIO
help
diff --git a/drivers/net/mvneta.c b/drivers/net/mvneta.c
index d2c42c4396..07919d6d35 100644
--- a/drivers/net/mvneta.c
+++ b/drivers/net/mvneta.c
@@ -91,6 +91,8 @@ DECLARE_GLOBAL_DATA_PTR;
#define MVNETA_WIN_SIZE_MASK (0xffff0000)
#define MVNETA_BASE_ADDR_ENABLE 0x2290
#define MVNETA_BASE_ADDR_ENABLE_BIT 0x1
+#define MVNETA_AC5_CNM_DDR_TARGET 0x2
+#define MVNETA_AC5_CNM_DDR_ATTR 0xb
#define MVNETA_PORT_ACCESS_PROTECT 0x2294
#define MVNETA_PORT_ACCESS_PROTECT_WIN0_RW 0x3
#define MVNETA_PORT_CONFIG 0x2400
@@ -282,6 +284,8 @@ struct mvneta_port {
struct gpio_desc phy_reset_gpio;
struct gpio_desc sfp_tx_disable_gpio;
#endif
+
+ uintptr_t dma_base; /* base address for DMA address decoding */
};
/* The mvneta_tx_desc and mvneta_rx_desc structures describe the
@@ -513,10 +517,19 @@ static void mvneta_rxq_desc_num_update(struct mvneta_port *pp,
static struct mvneta_rx_desc *
mvneta_rxq_next_desc_get(struct mvneta_rx_queue *rxq)
{
+ struct mvneta_rx_desc *curr;
int rx_desc = rxq->next_desc_to_proc;
+ /* validate RX descriptor */
+ curr = rxq->descs + rx_desc;
+ if (curr->data_size == 0) {
+ /* do it to read real descriptor next time */
+ DSB;
+ return NULL;
+ }
+
rxq->next_desc_to_proc = MVNETA_QUEUE_NEXT_DESC(rxq, rx_desc);
- return rxq->descs + rx_desc;
+ return curr;
}
/* Tx descriptors helper methods */
@@ -1343,6 +1356,29 @@ static void mvneta_conf_mbus_windows(struct mvneta_port *pp)
mvreg_write(pp, MVNETA_BASE_ADDR_ENABLE, win_enable);
}
+static void mvneta_conf_ac5_cnm_xbar_windows(struct mvneta_port *pp)
+{
+ int i;
+
+ /* Clear all windows */
+ for (i = 0; i < 6; i++) {
+ mvreg_write(pp, MVNETA_WIN_BASE(i), 0);
+ mvreg_write(pp, MVNETA_WIN_SIZE(i), 0);
+
+ if (i < 4)
+ mvreg_write(pp, MVNETA_WIN_REMAP(i), 0);
+ }
+
+ /*
+ * Setup window #0 base 0x0 to target XBAR port 2 (AMB2), attribute 0xb, size 4GB
+ * AMB2 address decoder remaps 0x0 to DDR 64 bit base address
+ */
+ mvreg_write(pp, MVNETA_WIN_BASE(0),
+ (MVNETA_AC5_CNM_DDR_ATTR << 8) | MVNETA_AC5_CNM_DDR_TARGET);
+ mvreg_write(pp, MVNETA_WIN_SIZE(0), 0xffff0000);
+ mvreg_write(pp, MVNETA_BASE_ADDR_ENABLE, 0x3e);
+}
+
/* Power up the port */
static int mvneta_port_power_up(struct mvneta_port *pp, int phy_mode)
{
@@ -1508,11 +1544,15 @@ static int mvneta_recv(struct udevice *dev, int flags, uchar **packetp)
*/
rx_desc = mvneta_rxq_next_desc_get(rxq);
+ if (!rx_desc)
+ return 0;
+
rx_status = rx_desc->status;
if (!mvneta_rxq_desc_is_first_last(rx_status) ||
(rx_status & MVNETA_RXD_ERR_SUMMARY)) {
mvneta_rx_error(pp, rx_desc);
- /* leave the descriptor untouched */
+ /* invalidate the descriptor */
+ rx_desc->data_size = 0;
return -EIO;
}
@@ -1525,13 +1565,15 @@ static int mvneta_recv(struct udevice *dev, int flags, uchar **packetp)
* No cache invalidation needed here, since the rx_buffer's are
* located in a uncached memory region
*/
- *packetp = data;
+ *packetp = data + pp->dma_base;
/*
* Only mark one descriptor as free
* since only one was processed
*/
mvneta_rxq_desc_num_update(pp, rxq, 1, 1);
+ /* invalidate the descriptor */
+ rx_desc->data_size = 0;
}
return rx_bytes;
@@ -1544,6 +1586,11 @@ static int mvneta_probe(struct udevice *dev)
struct ofnode_phandle_args sfp_args;
#endif
void *bd_space;
+ void *blob = (void *)gd->fdt_blob;
+ int node = dev_of_offset(dev);
+ const int *cell;
+ int len;
+
/*
* Allocate buffer area for descs and rx_buffers. This is only
@@ -1577,9 +1624,21 @@ static int mvneta_probe(struct udevice *dev)
/* Configure MBUS address windows */
if (device_is_compatible(dev, "marvell,armada-3700-neta"))
mvneta_bypass_mbus_windows(pp);
+ else if (device_is_compatible(dev, "marvell,armada-ac5-neta"))
+ mvneta_conf_ac5_cnm_xbar_windows(pp);
else
mvneta_conf_mbus_windows(pp);
+ /* fetch dma ranges property */
+ cell = fdt_getprop(blob, node, "dma-ranges", &len);
+ if (cell && len >= 4 * sizeof(int)) {
+ /* RAZA - TODO do that in loop by address-cells size */
+ pp->dma_base = fdt32_to_cpu(cell[1]);
+ pp->dma_base = (pp->dma_base << 32) | fdt32_to_cpu(cell[2]);
+ } else {
+ pp->dma_base = 0;
+ }
+
#if CONFIG_IS_ENABLED(DM_GPIO)
if (!dev_read_phandle_with_args(dev, "sfp", NULL, 0, 0, &sfp_args) &&
ofnode_is_enabled(sfp_args.node))
@@ -1620,6 +1679,7 @@ static const struct eth_ops mvneta_ops = {
static const struct udevice_id mvneta_ids[] = {
{ .compatible = "marvell,armada-370-neta" },
+ { .compatible = "marvell,armada-ac5-neta" },
{ .compatible = "marvell,armada-xp-neta" },
{ .compatible = "marvell,armada-3700-neta" },
{ }
--
2.37.3
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v2 2/6] usb: ehci: ehci-marvell: Support for marvell,ac5-ehci
2022-09-20 8:31 [PATCH v2 0/6] arm: mvebu: Support for 98DX25xx/98DX35xx (AlleyCat5) Chris Packham
2022-09-20 8:31 ` [PATCH v2 1/6] net: mvneta: Add support for AlleyCat5 Chris Packham
@ 2022-09-20 8:31 ` Chris Packham
2022-09-20 9:08 ` Pali Rohár
2022-09-20 8:31 ` [PATCH v2 3/6] pinctrl: mvebu: Add AlleyCat5 support Chris Packham
` (3 subsequent siblings)
5 siblings, 1 reply; 17+ messages in thread
From: Chris Packham @ 2022-09-20 8:31 UTC (permalink / raw)
To: Stefan Roese
Cc: Elad Nachman, Vadym Kochan, Chris Packham, Adam Ford,
Lukasz Majewski, Marek Behún, Marek Vasut, Pali Rohár,
Weijie Gao, u-boot
Unlike the other 64-bit mvebu SoCs the AlleyCat5 uses the older ehci
block from the 32-bit SoCs. Adapt the ehci-marvell.c driver to cope with
the fact that the ac5 does not have the mbus infrastructure the 32-bit
SoCs have and ensure USB_EHCI_IS_TDI is selected.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
---
(no changes since v1)
drivers/usb/host/Kconfig | 1 +
drivers/usb/host/ehci-marvell.c | 57 +++++++++++++++++++++++++++------
2 files changed, 48 insertions(+), 10 deletions(-)
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index a0f48f09a7..628078f495 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -178,6 +178,7 @@ config USB_EHCI_MARVELL
depends on ARCH_MVEBU || ARCH_KIRKWOOD || ARCH_ORION5X
default y
select USB_EHCI_IS_TDI if !ARM64
+ select USB_EHCI_IS_TDI if ALLEYCAT_5
---help---
Enables support for the on-chip EHCI controller on MVEBU SoCs.
diff --git a/drivers/usb/host/ehci-marvell.c b/drivers/usb/host/ehci-marvell.c
index b7e60c690a..7d859b9cce 100644
--- a/drivers/usb/host/ehci-marvell.c
+++ b/drivers/usb/host/ehci-marvell.c
@@ -48,12 +48,17 @@ struct ehci_mvebu_priv {
fdt_addr_t hcd_base;
};
+#define USB_TO_DRAM_TARGET_ID 0x2
+#define USB_TO_DRAM_ATTR_ID 0x0
+#define USB_DRAM_BASE 0x00000000
+#define USB_DRAM_SIZE 0xfff /* don't overrun u-boot source (was 0xffff) */
+
/*
* Once all the older Marvell SoC's (Orion, Kirkwood) are converted
* to the common mvebu archticture including the mbus setup, this
* will be the only function needed to configure the access windows
*/
-static void usb_brg_adrdec_setup(void *base)
+static void usb_brg_adrdec_setup(struct udevice *dev, void *base)
{
const struct mbus_dram_target_info *dram;
int i;
@@ -65,16 +70,34 @@ static void usb_brg_adrdec_setup(void *base)
writel(0, base + USB_WINDOW_BASE(i));
}
- for (i = 0; i < dram->num_cs; i++) {
- const struct mbus_dram_window *cs = dram->cs + i;
+ if (device_is_compatible(dev, "marvell,ac5-ehci")) {
+ /*
+ * use decoding window to map dram address seen by usb to 0x0
+ */
/* Write size, attributes and target id to control register */
- writel(((cs->size - 1) & 0xffff0000) | (cs->mbus_attr << 8) |
- (dram->mbus_dram_target_id << 4) | 1,
- base + USB_WINDOW_CTRL(i));
+ writel((USB_DRAM_SIZE << 16) | (USB_TO_DRAM_ATTR_ID << 8) |
+ (USB_TO_DRAM_TARGET_ID << 4) | 1,
+ base + USB_WINDOW_CTRL(0));
/* Write base address to base register */
- writel(cs->base, base + USB_WINDOW_BASE(i));
+ writel(USB_DRAM_BASE, base + USB_WINDOW_BASE(0));
+
+ debug("## AC5 decoding windows, ctrl[%p]=0x%x, base[%p]=0x%x\n",
+ base + USB_WINDOW_CTRL(0), readl(base + USB_WINDOW_CTRL(0)),
+ base + USB_WINDOW_BASE(0), readl(base + USB_WINDOW_BASE(0)));
+ } else {
+ for (i = 0; i < dram->num_cs; i++) {
+ const struct mbus_dram_window *cs = dram->cs + i;
+
+ /* Write size, attributes and target id to control register */
+ writel(((cs->size - 1) & 0xffff0000) | (cs->mbus_attr << 8) |
+ (dram->mbus_dram_target_id << 4) | 1,
+ base + USB_WINDOW_CTRL(i));
+
+ /* Write base address to base register */
+ writel(cs->base, base + USB_WINDOW_BASE(i));
+ }
}
}
@@ -126,15 +149,28 @@ static int ehci_mvebu_probe(struct udevice *dev)
if (device_is_compatible(dev, "marvell,armada-3700-ehci"))
marvell_ehci_ops.powerup_fixup = marvell_ehci_powerup_fixup;
else
- usb_brg_adrdec_setup((void *)priv->hcd_base);
+ usb_brg_adrdec_setup(dev, (void *)priv->hcd_base);
hccr = (struct ehci_hccr *)(priv->hcd_base + 0x100);
hcor = (struct ehci_hcor *)
((uintptr_t)hccr + HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
debug("ehci-marvell: init hccr %lx and hcor %lx hc_length %ld\n",
- (uintptr_t)hccr, (uintptr_t)hcor,
- (uintptr_t)HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
+ (uintptr_t)hccr, (uintptr_t)hcor,
+ (uintptr_t)HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
+
+#define PHY_CALIB_OFFSET 0x808
+ /*
+ * Trigger calibration during each usb start/reset:
+ * BIT 13 to 0, and then to 1
+ */
+ if (device_is_compatible(dev, "marvell,ac5-ehci")) {
+ void *phy_calib_reg = (void *)(priv->hcd_base + PHY_CALIB_OFFSET);
+ u32 val = readl(phy_calib_reg) & (~BIT(13));
+
+ writel(val, phy_calib_reg);
+ writel(val | BIT(13), phy_calib_reg);
+ }
return ehci_register(dev, hccr, hcor, &marvell_ehci_ops, 0,
USB_INIT_HOST);
@@ -143,6 +179,7 @@ static int ehci_mvebu_probe(struct udevice *dev)
static const struct udevice_id ehci_usb_ids[] = {
{ .compatible = "marvell,orion-ehci", },
{ .compatible = "marvell,armada-3700-ehci", },
+ { .compatible = "marvell,ac5-ehci", },
{ }
};
--
2.37.3
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v2 3/6] pinctrl: mvebu: Add AlleyCat5 support
2022-09-20 8:31 [PATCH v2 0/6] arm: mvebu: Support for 98DX25xx/98DX35xx (AlleyCat5) Chris Packham
2022-09-20 8:31 ` [PATCH v2 1/6] net: mvneta: Add support for AlleyCat5 Chris Packham
2022-09-20 8:31 ` [PATCH v2 2/6] usb: ehci: ehci-marvell: Support for marvell,ac5-ehci Chris Packham
@ 2022-09-20 8:31 ` Chris Packham
2022-09-20 8:31 ` [PATCH v2 4/6] misc: mvebu: Add sample at reset driver Chris Packham
` (2 subsequent siblings)
5 siblings, 0 replies; 17+ messages in thread
From: Chris Packham @ 2022-09-20 8:31 UTC (permalink / raw)
To: Stefan Roese; +Cc: Elad Nachman, Vadym Kochan, Chris Packham, Tom Rini, u-boot
This uses the same IP block as the Armada-8K SoCs.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
---
(no changes since v1)
drivers/pinctrl/mvebu/Kconfig | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/pinctrl/mvebu/Kconfig b/drivers/pinctrl/mvebu/Kconfig
index 574fb4dfb0..7c51d138c8 100644
--- a/drivers/pinctrl/mvebu/Kconfig
+++ b/drivers/pinctrl/mvebu/Kconfig
@@ -15,7 +15,7 @@ config PINCTRL_ARMADA_37XX
Marvell's Armada-37xx SoC.
config PINCTRL_ARMADA_8K
- depends on ARMADA_8K && PINCTRL_FULL
+ depends on (ARMADA_8K || ALLEYCAT_5) && PINCTRL_FULL
bool "Armada 7k/8k pin control driver"
help
Support pin multiplexing and pin configuration control on
--
2.37.3
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v2 4/6] misc: mvebu: Add sample at reset driver
2022-09-20 8:31 [PATCH v2 0/6] arm: mvebu: Support for 98DX25xx/98DX35xx (AlleyCat5) Chris Packham
` (2 preceding siblings ...)
2022-09-20 8:31 ` [PATCH v2 3/6] pinctrl: mvebu: Add AlleyCat5 support Chris Packham
@ 2022-09-20 8:31 ` Chris Packham
2022-09-20 10:42 ` Pali Rohár
2022-09-20 8:31 ` [PATCH v2 5/6] arm: mvebu: Support for 98DX25xx/98DX35xx SoC Chris Packham
2022-09-20 8:31 ` [PATCH v2 6/6] arm: mvebu: Add RD-AC5X board Chris Packham
5 siblings, 1 reply; 17+ messages in thread
From: Chris Packham @ 2022-09-20 8:31 UTC (permalink / raw)
To: Stefan Roese
Cc: Elad Nachman, Vadym Kochan, Chris Packham, Alice Guo, Jim Liu,
Keerthy, Marek Vasut, Michael Scott, Michael Walle, Peng Fan,
Sean Anderson, Simon Glass, Tom Rini, Ye Li, u-boot
Add a new UCLASS_SAR, the generic SAR code and an Alleycat5 driver. This
has been adapted from the Marvell SDK but only the AC5 driver has been
brought through (other drivers exist for the ap806, ap807 and cp110 IP
blocks).
Signed-off-by: Chris Packham <judge.packham@gmail.com>
---
(no changes since v1)
drivers/misc/Kconfig | 6 ++
drivers/misc/Makefile | 1 +
drivers/misc/mvebu_sar/Makefile | 4 +
drivers/misc/mvebu_sar/ac5_sar.c | 119 +++++++++++++++++++++++
drivers/misc/mvebu_sar/sar-uclass.c | 146 ++++++++++++++++++++++++++++
include/dm/uclass-id.h | 1 +
include/fdtdec.h | 4 +
include/mvebu/mvebu_chip_sar.h | 73 ++++++++++++++
include/mvebu/sar.h | 57 +++++++++++
include/mvebu/var.h | 28 ++++++
include/sar-uclass.h | 23 +++++
lib/fdtdec.c | 6 +-
12 files changed, 467 insertions(+), 1 deletion(-)
create mode 100644 drivers/misc/mvebu_sar/Makefile
create mode 100644 drivers/misc/mvebu_sar/ac5_sar.c
create mode 100644 drivers/misc/mvebu_sar/sar-uclass.c
create mode 100644 include/mvebu/mvebu_chip_sar.h
create mode 100644 include/mvebu/sar.h
create mode 100644 include/mvebu/var.h
create mode 100644 include/sar-uclass.h
diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
index a6da6e215d..4e99ef29d9 100644
--- a/drivers/misc/Kconfig
+++ b/drivers/misc/Kconfig
@@ -645,4 +645,10 @@ config SL28CPLD
the base driver which provides common access methods for the
sub-drivers.
+config MVEBU_SAR
+ bool "MVEBU SAR driver"
+ depends on ARCH_MVEBU
+ help
+ Support MVEBU SAR driver
+
endmenu
diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
index d494639cd9..3cf976edd8 100644
--- a/drivers/misc/Makefile
+++ b/drivers/misc/Makefile
@@ -62,6 +62,7 @@ obj-$(CONFIG_NUVOTON_NCT6102D) += nuvoton_nct6102d.o
obj-$(CONFIG_P2SB) += p2sb-uclass.o
obj-$(CONFIG_PCA9551_LED) += pca9551_led.o
obj-$(CONFIG_$(SPL_)PWRSEQ) += pwrseq-uclass.o
+obj-$(CONFIG_MVEBU_SAR) += mvebu_sar/
ifdef CONFIG_QFW
obj-y += qfw.o
obj-$(CONFIG_QFW_PIO) += qfw_pio.o
diff --git a/drivers/misc/mvebu_sar/Makefile b/drivers/misc/mvebu_sar/Makefile
new file mode 100644
index 0000000000..6f339fb7b4
--- /dev/null
+++ b/drivers/misc/mvebu_sar/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0+
+
+obj-$(CONFIG_MVEBU_SAR) += sar-uclass.o
+obj-$(CONFIG_ALLEYCAT_5) += ac5_sar.o
diff --git a/drivers/misc/mvebu_sar/ac5_sar.c b/drivers/misc/mvebu_sar/ac5_sar.c
new file mode 100644
index 0000000000..67b2110bc8
--- /dev/null
+++ b/drivers/misc/mvebu_sar/ac5_sar.c
@@ -0,0 +1,119 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <errno.h>
+#include <fdtdec.h>
+#include <mvebu/mvebu_chip_sar.h>
+#include <dm.h>
+
+#include <sar-uclass.h>
+
+#define MHz 1000000
+
+#define BIT_VAL(b) ((1ULL << ((b) + 1)) - 1)
+#define BIT_RANGE(Bl, Bh) (BIT_VAL(Bh) - BIT_VAL((Bl) - 1))
+
+#define PLL_MAX_CHOICE 4
+
+#define CPU_TYPE_AC5 0
+#define CPU_TYPE_AC5x 1
+#define CPU_TYPE_LAST 2
+
+static const u32 pll_freq_tbl[CPU_TYPE_LAST][SAR_AP_FABRIC_FREQ + 1][PLL_MAX_CHOICE] = {
+ [CPU_TYPE_AC5] = {
+ [SAR_CPU_FREQ] = {
+ 800 * MHz, 1200 * MHz, 1400 * MHz, 1000 * MHz
+ },
+ [SAR_DDR_FREQ] = {
+ 1200 * MHz, 800 * MHz, 0, 0
+ },
+ [SAR_AP_FABRIC_FREQ] = {
+ 396 * MHz, 290 * MHz, 197 * MHz, 0
+ },
+ },
+ [CPU_TYPE_AC5x] = {
+ [SAR_CPU_FREQ] = {
+ 800 * MHz, 1200 * MHz, 1500 * MHz, 1600 * MHz
+ },
+ [SAR_DDR_FREQ] = {
+ 1200 * MHz, 800 * MHz, 0, 0
+ },
+ [SAR_AP_FABRIC_FREQ] = {
+ 0, 0, 0, 0
+ }
+ }
+};
+
+static const u32 soc_sar_masks_tbl[CPU_TYPE_LAST][SAR_AP_FABRIC_FREQ + 1] = {
+ [CPU_TYPE_AC5] = {
+ [SAR_CPU_FREQ] = BIT_RANGE(18, 20),
+ [SAR_DDR_FREQ] = BIT_RANGE(16, 17),
+ [SAR_AP_FABRIC_FREQ] = BIT_RANGE(22, 23),
+ },
+ [CPU_TYPE_AC5x] = {
+ [SAR_CPU_FREQ] = BIT_RANGE(8, 10),
+ [SAR_DDR_FREQ] = BIT_RANGE(6, 7),
+ [SAR_AP_FABRIC_FREQ] = 1,
+ },
+};
+
+static int ac5_sar_value_get(struct udevice *dev, enum mvebu_sar_opts sar_opt,
+ struct sar_val *val)
+{
+ u32 *pSarBase = (u32 *)(((struct dm_sar_pdata *)dev_get_priv(dev))->sar_base);
+ u32 sar_reg_val = readl(pSarBase);
+ u32 mask;
+ unsigned char choice;
+ int cpu_type = ((readl(0x7f90004c) & 0xFF000) >> 12) == 0x98 ? CPU_TYPE_AC5x : CPU_TYPE_AC5;
+
+ if (sar_opt > SAR_AP_FABRIC_FREQ) {
+ pr_err("AC5-SAR: Unsupported SAR option %d.\n", sar_opt);
+ return -EINVAL;
+ }
+
+ mask = soc_sar_masks_tbl[cpu_type][sar_opt];
+ /* The choice within the bits allocated for a specific PLL */
+ choice = (sar_reg_val & mask) >> (__builtin_ffs(mask) - 1);
+
+ val->freq = pll_freq_tbl[cpu_type][sar_opt][choice];
+ return 0;
+}
+
+static int ac5_sar_init(struct udevice *dev)
+{
+ int ret, i;
+
+ u32 sar_list[] = {
+ SAR_CPU_FREQ,
+ SAR_DDR_FREQ,
+ SAR_AP_FABRIC_FREQ
+ };
+
+ for (i = 0; i < ARRAY_SIZE(sar_list); i++) {
+ ret = mvebu_sar_id_register(dev, sar_list[i]);
+ if (ret) {
+ pr_err("Failed to register SAR %d, for AC5\n",
+ sar_list[i]);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static const struct sar_ops ac5_sar_ops = {
+ .sar_init_func = ac5_sar_init,
+ .sar_value_get_func = ac5_sar_value_get,
+ .sar_dump_func = NULL,
+};
+
+U_BOOT_DRIVER(ac5_sar) = {
+ .name = "ac5_sar",
+ .id = UCLASS_SAR,
+ .priv_auto = sizeof(struct dm_sar_pdata),
+ .ops = &ac5_sar_ops,
+};
diff --git a/drivers/misc/mvebu_sar/sar-uclass.c b/drivers/misc/mvebu_sar/sar-uclass.c
new file mode 100644
index 0000000000..d9cb019d5d
--- /dev/null
+++ b/drivers/misc/mvebu_sar/sar-uclass.c
@@ -0,0 +1,146 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <errno.h>
+#include <fdtdec.h>
+#include <dm.h>
+#include <dm/device-internal.h>
+#include <sar-uclass.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define SAR_MAX_CHIP 4
+
+UCLASS_DRIVER(sar) = {
+ .name = "sar",
+ .id = UCLASS_SAR,
+};
+
+struct udevice *__section(".data") soc_sar_info[SAR_MAX_IDX];
+
+int mvebu_sar_id_register(struct udevice *dev, u32 sar_id)
+{
+ if (soc_sar_info[sar_id]) {
+ pr_err("sar %d was already registered.\n", sar_id);
+ return -EBUSY;
+ }
+ soc_sar_info[sar_id] = dev;
+
+ return 0;
+}
+
+/* find all drivers for sar device and initialize each driver */
+int mvebu_sar_init(void)
+{
+ int ret, i;
+ int node, chip_count, sar_list[SAR_MAX_CHIP];
+ const void *blob = gd->fdt_blob;
+ struct udevice *sar_chip[SAR_MAX_CHIP];
+ struct dm_sar_pdata *priv;
+ const struct sar_ops *ops;
+ struct udevice *parent;
+ struct driver_info sar_drivers[SAR_MAX_CHIP];
+ void *sar_base = NULL;
+ const char *sar_driver, *sar_name;
+
+ chip_count = fdtdec_find_aliases_for_id(blob, "sar-reg",
+ COMPAT_MVEBU_SAR_REG_COMMON,
+ sar_list, SAR_MAX_CHIP);
+
+ if (chip_count <= 0) {
+ pr_err("Cannot find sample-at-reset dt entry (%d).\n",
+ chip_count);
+ return -ENODEV;
+ }
+ uclass_get_device_by_name(UCLASS_ROOT, "root_driver", &parent);
+ memset(soc_sar_info, 0, sizeof(soc_sar_info));
+
+ for (i = 0; i < chip_count ; i++) {
+ node = sar_list[i];
+ if (node <= 0)
+ continue;
+
+ /* Skip if Node is disabled */
+ if (!fdtdec_get_is_enabled(blob, node))
+ continue;
+ /* Binding stage */
+ sar_driver = fdt_getprop(blob, node, "sar-driver", NULL);
+ sar_drivers[i].name = sar_driver;
+ ret = device_bind_by_name(parent, false,
+ &sar_drivers[i], &sar_chip[i]);
+
+ if (!sar_chip[i]) {
+ pr_err("SAR driver binding failed\n");
+ return 0;
+ }
+
+ /* fetch driver info from device-tree */
+ sar_base = (void *)fdtdec_get_addr_size_auto_noparent(blob,
+ node, "reg", 0, NULL, true);
+ if (!sar_base) {
+ pr_err("SAR address isn't found in the device-tree\n");
+ return 0;
+ }
+ sar_name = fdt_getprop(blob, node, "sar-name", NULL);
+ /* Initialize driver priv struct */
+ device_probe(sar_chip[i]);
+ priv = dev_get_priv(sar_chip[i]);
+ priv->sar_base = sar_base;
+ priv->sar_name = sar_name;
+ ops = device_get_ops(sar_chip[i]);
+ if (!ops->sar_init_func)
+ return -EINVAL;
+
+ ret = ops->sar_init_func(sar_chip[i]);
+ if (ret) {
+ pr_err("sar_init failed (%d).\n", ret);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+int mvebu_sar_value_get(enum mvebu_sar_opts opt, struct sar_val *val)
+{
+ const struct sar_ops *ops;
+
+ if (soc_sar_info[opt]) {
+ ops = device_get_ops(soc_sar_info[opt]);
+ return ops->sar_value_get_func(soc_sar_info[opt], opt, val);
+ }
+
+ pr_err("SAR - No chip registered on sar %d.\n", opt);
+ return -ENODEV;
+}
+
+char *mvebu_sar_bootsrc_to_name(enum mvebu_bootsrc_type src)
+{
+ switch (src) {
+ case(BOOTSRC_NAND):
+ return "nand";
+ case(BOOTSRC_SPI):
+ case(BOOTSRC_AP_SPI):
+ return "spi";
+ case(BOOTSRC_SD_EMMC):
+ case(BOOTSRC_AP_SD_EMMC):
+ return "mmc";
+ case(BOOTSRC_NOR):
+ return "nor";
+ default:
+ return "unknown";
+ }
+}
+
+void mvebu_sar_dump(struct udevice *dev)
+{
+ const struct sar_ops *ops;
+
+ ops = device_get_ops(dev);
+
+ ops->sar_dump_func(dev);
+}
diff --git a/include/dm/uclass-id.h b/include/dm/uclass-id.h
index a432e43871..2213e76d38 100644
--- a/include/dm/uclass-id.h
+++ b/include/dm/uclass-id.h
@@ -107,6 +107,7 @@ enum uclass_id {
UCLASS_RESET, /* Reset controller device */
UCLASS_RNG, /* Random Number Generator */
UCLASS_RTC, /* Real time clock device */
+ UCLASS_SAR, /* Reset Sample Configuration */
UCLASS_SCMI_AGENT, /* Interface with an SCMI server */
UCLASS_SCSI, /* SCSI device */
UCLASS_SERIAL, /* Serial UART */
diff --git a/include/fdtdec.h b/include/fdtdec.h
index 12355afd7f..d8923ba443 100644
--- a/include/fdtdec.h
+++ b/include/fdtdec.h
@@ -199,6 +199,10 @@ enum fdt_compat_id {
COMPAT_ALTERA_SOCFPGA_FPGA0, /* SOCFPGA FPGA manager */
COMPAT_ALTERA_SOCFPGA_NOC, /* SOCFPGA Arria 10 NOC */
COMPAT_ALTERA_SOCFPGA_CLK_INIT, /* SOCFPGA Arria 10 clk init */
+ COMPAT_MVEBU_SAR, /* Marvell Sampled-at-Reset */
+ COMPAT_MVEBU_SAR_REG_COMMON, /* Marvell Sampled-at-Reset Common */
+ COMPAT_MVEBU_SAR_REG_AP806, /* Marvell Sampled-at-Reset for ap806/ap807 */
+ COMPAT_MVEBU_SAR_REG_CP110, /* Marvell Sampled-at-Reset for cp110 */
COMPAT_COUNT,
};
diff --git a/include/mvebu/mvebu_chip_sar.h b/include/mvebu/mvebu_chip_sar.h
new file mode 100644
index 0000000000..4781aa06c4
--- /dev/null
+++ b/include/mvebu/mvebu_chip_sar.h
@@ -0,0 +1,73 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ */
+
+#ifndef _MVEBU_CHIP_SAR_H_
+#define _MVEBU_CHIP_SAR_H_
+
+#include <asm/types.h>
+
+struct udevice;
+
+/*
+ * List of boot source options.
+ * Return value for each of the options:
+ * - SAR_CPU_FREQ: Frequency (Hz)
+ * - SAR_DDR_FREQ: Frequency (Hz)
+ * - SAR_AP_FABRIC_FREQ: Frequency (Hz)
+ * - SAR_CP_FABRIC_FREQ: Frequency (Hz)
+ * - SAR_BOOT_SRC: Boot source type (see mvebu_bootsrc_type)
+ */
+enum mvebu_sar_opts {
+ SAR_CPU_FREQ = 0,
+ SAR_DDR_FREQ,
+ SAR_AP_FABRIC_FREQ,
+ SAR_CP_FABRIC_FREQ,
+ SAR_CP0_PCIE0_CLK,
+ SAR_CP0_PCIE1_CLK,
+ SAR_CP1_PCIE0_CLK,
+ SAR_CP1_PCIE1_CLK,
+ SAR_BOOT_SRC,
+ SAR_MAX_IDX
+};
+
+enum mvebu_bootsrc_type {
+ BOOTSRC_NAND,
+ BOOTSRC_SPI,
+ BOOTSRC_AP_SPI,
+ BOOTSRC_SD_EMMC,
+ BOOTSRC_AP_SD_EMMC,
+ BOOTSRC_NOR,
+ BOOTSRC_MAX_IDX
+};
+
+/*
+ * sample-at-reset information
+ * raw_sar_val: Raw value out of the sample-at-reset register.
+ * This is hw dependent and should not be used for comparison
+ * purposes (useful for debug, or verbose information).
+ * bootsrc (SAR_BOOT_SRC):
+ * type: Boot source interface type.
+ * index: When applicable, indicates the interface index (e.g. SPI #1,
+ * NAND #0).
+ * freq: Frequency in Hz.
+ */
+struct sar_val {
+ u32 raw_sar_val;
+ union {
+ struct {
+ enum mvebu_bootsrc_type type;
+ int index;
+ } bootsrc;
+ u32 freq;
+ u32 clk_direction; /* input = 0 */
+ };
+};
+
+int mvebu_sar_init(void);
+int mvebu_sar_value_get(enum mvebu_sar_opts opt, struct sar_val *val);
+void mvebu_sar_dump(struct udevice *dev);
+char *mvebu_sar_bootsrc_to_name(enum mvebu_bootsrc_type src);
+
+#endif /* _MVEBU_CHIP_SAR_H_ */
diff --git a/include/mvebu/sar.h b/include/mvebu/sar.h
new file mode 100644
index 0000000000..bd0837d6a3
--- /dev/null
+++ b/include/mvebu/sar.h
@@ -0,0 +1,57 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ */
+
+#ifndef _SAR_H_
+#define _SAR_H_
+
+#include <linux/compiler.h>
+#include <mvebu/var.h>
+
+#define MAX_SAR_CHIPS 4
+#define MAX_SAR 8
+
+enum sar_variables {
+ CPUS_NUM_SAR = 0,
+ CPU0_ENDIANESS_SAR,
+ FREQ_SAR,
+ CPU_FREQ_SAR,
+ FAB_REQ_SAR,
+ BOOT_SRC_SAR,
+ BOOT_WIDTH_SAR,
+ PEX_MODE_SAR,
+ L2_SIZE_SAR,
+ DRAM_ECC_SAR,
+ DRAM_BUS_WIDTH_SAR,
+};
+
+struct sar_var {
+ u8 start_bit;
+ u8 bit_length;
+ u8 option_cnt;
+ u8 active;
+ bool swap_bit;
+ char *desc;
+ char *key;
+ struct var_opts option_desc[MAX_VAR_OPTIONS];
+};
+
+struct sar_data {
+ u32 chip_addr[MAX_SAR_CHIPS];
+ u8 chip_count;
+ u8 bit_width;
+ struct sar_var sar_lookup[MAX_SAR];
+};
+
+int sar_read_all(void);
+int sar_default_key(const char *key);
+int sar_default_all(void);
+int sar_write_key(const char *key, int val);
+int sar_print_key(const char *key);
+void sar_list_keys(void);
+int sar_list_key_opts(const char *key);
+int sar_is_available(void);
+void sar_init(void);
+
+#endif /* _SAR_H_ */
diff --git a/include/mvebu/var.h b/include/mvebu/var.h
new file mode 100644
index 0000000000..6bd315c841
--- /dev/null
+++ b/include/mvebu/var.h
@@ -0,0 +1,28 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ */
+
+#ifndef _VAR_H_
+#define _VAR_H_
+
+#include <linux/compiler.h>
+
+#define INVALID_KEY 0xFF
+#define MAX_VAR_OPTIONS 10
+
+#define VAR_IS_DEFAULT 0x1
+#define VAR_IS_LAST 0x2
+
+struct var_opts {
+ u8 value;
+ char *desc;
+ u8 flags;
+};
+
+struct var_desc {
+ char *key;
+ char *description;
+};
+
+#endif /* _VAR_H_ */
diff --git a/include/sar-uclass.h b/include/sar-uclass.h
new file mode 100644
index 0000000000..8b9cc08847
--- /dev/null
+++ b/include/sar-uclass.h
@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ */
+
+#include <mvebu/mvebu_chip_sar.h>
+
+struct udevice;
+
+struct sar_ops {
+ int (*sar_init_func)(struct udevice *dev);
+ int (*sar_dump_func)(struct udevice *dev);
+ int (*sar_value_get_func)(struct udevice *dev, enum mvebu_sar_opts sar,
+ struct sar_val *val);
+ int (*sar_bootsrc_get)(struct udevice *dev, u32 *idx);
+};
+
+struct dm_sar_pdata {
+ void __iomem *sar_base;
+ const char *sar_name;
+};
+
+int mvebu_sar_id_register(struct udevice *dev, u32 sar_id);
diff --git a/lib/fdtdec.c b/lib/fdtdec.c
index 96b6b71a60..26e5c82bcd 100644
--- a/lib/fdtdec.c
+++ b/lib/fdtdec.c
@@ -74,7 +74,11 @@ static const char * const compat_names[COMPAT_COUNT] = {
COMPAT(ALTERA_SOCFPGA_F2SDR2, "altr,socfpga-fpga2sdram2-bridge"),
COMPAT(ALTERA_SOCFPGA_FPGA0, "altr,socfpga-a10-fpga-mgr"),
COMPAT(ALTERA_SOCFPGA_NOC, "altr,socfpga-a10-noc"),
- COMPAT(ALTERA_SOCFPGA_CLK_INIT, "altr,socfpga-a10-clk-init")
+ COMPAT(ALTERA_SOCFPGA_CLK_INIT, "altr,socfpga-a10-clk-init"),
+ COMPAT(MVEBU_SAR, "marvell,sample-at-reset"),
+ COMPAT(MVEBU_SAR_REG_COMMON, "marvell,sample-at-reset-common"),
+ COMPAT(MVEBU_SAR_REG_AP806, "marvell,sample-at-reset-ap806"),
+ COMPAT(MVEBU_SAR_REG_CP110, "marvell,sample-at-reset-cp110"),
};
static const char *const fdt_src_name[] = {
--
2.37.3
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v2 5/6] arm: mvebu: Support for 98DX25xx/98DX35xx SoC
2022-09-20 8:31 [PATCH v2 0/6] arm: mvebu: Support for 98DX25xx/98DX35xx (AlleyCat5) Chris Packham
` (3 preceding siblings ...)
2022-09-20 8:31 ` [PATCH v2 4/6] misc: mvebu: Add sample at reset driver Chris Packham
@ 2022-09-20 8:31 ` Chris Packham
2022-09-20 9:22 ` Pali Rohár
2022-09-20 8:31 ` [PATCH v2 6/6] arm: mvebu: Add RD-AC5X board Chris Packham
5 siblings, 1 reply; 17+ messages in thread
From: Chris Packham @ 2022-09-20 8:31 UTC (permalink / raw)
To: Stefan Roese
Cc: Elad Nachman, Vadym Kochan, Chris Packham, Marek Behún,
Pali Rohár, Tom Rini, u-boot
Add support for the Allecat5/Alleycat5X SoC. These are L3 switches with
an integrated CPU (referred to as the CnM block in Marvell's
documentation). These have dual ARMv8.2 CPUs (Cortex-A55). This support
has been ported from Marvell's SDK which is based on a much older
version of U-Boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
---
(no changes since v1)
arch/arm/dts/ac5-98dx25xx.dtsi | 292 +++++++++++++++++++++++
arch/arm/dts/ac5-98dx35xx.dtsi | 17 ++
arch/arm/mach-mvebu/Kconfig | 5 +
arch/arm/mach-mvebu/Makefile | 1 +
arch/arm/mach-mvebu/alleycat5/Makefile | 9 +
arch/arm/mach-mvebu/alleycat5/clock.c | 49 ++++
arch/arm/mach-mvebu/alleycat5/cpu.c | 129 ++++++++++
arch/arm/mach-mvebu/alleycat5/soc.c | 229 ++++++++++++++++++
arch/arm/mach-mvebu/arm64-common.c | 15 ++
arch/arm/mach-mvebu/include/mach/clock.h | 11 +
arch/arm/mach-mvebu/include/mach/cpu.h | 4 +
arch/arm/mach-mvebu/include/mach/soc.h | 4 +
12 files changed, 765 insertions(+)
create mode 100644 arch/arm/dts/ac5-98dx25xx.dtsi
create mode 100644 arch/arm/dts/ac5-98dx35xx.dtsi
create mode 100644 arch/arm/mach-mvebu/alleycat5/Makefile
create mode 100644 arch/arm/mach-mvebu/alleycat5/clock.c
create mode 100644 arch/arm/mach-mvebu/alleycat5/cpu.c
create mode 100644 arch/arm/mach-mvebu/alleycat5/soc.c
create mode 100644 arch/arm/mach-mvebu/include/mach/clock.h
diff --git a/arch/arm/dts/ac5-98dx25xx.dtsi b/arch/arm/dts/ac5-98dx25xx.dtsi
new file mode 100644
index 0000000000..c31d2f08cf
--- /dev/null
+++ b/arch/arm/dts/ac5-98dx25xx.dtsi
@@ -0,0 +1,292 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree For AC5.
+ *
+ * Copyright (C) 2021 Marvell
+ * Copyright (C) 2022 Allied Telesis Labs
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ model = "Marvell AC5 SoC";
+ compatible = "marvell,ac5";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+ core1 {
+ cpu = <&cpu1>;
+ };
+ };
+ };
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a55";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ l2: l2-cache {
+ compatible = "cache";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_PPI 8 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pmu {
+ compatible = "arm,armv8-pmuv3";
+ interrupts = <GIC_PPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ config-space {
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+ compatible = "simple-bus";
+
+ sar-reg {
+ compatible = "marvell,sample-at-reset-common";
+ sar-driver = "ac5_sar";
+ sar-name = "ac5_sar";
+ status = "okay";
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ dma-ranges;
+
+ internal-regs@7f000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ /* 16M internal register @ 0x7f00_0000 */
+ ranges = <0x0 0x0 0x7f000000 0x1000000>;
+ dma-coherent;
+
+ uart0: serial@12000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x12000 0x100>;
+ reg-shift = <2>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ reg-io-width = <1>;
+ clocks = <&cnm_clock>;
+ status = "okay";
+ };
+
+ uart1: serial@12100 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x12100 0x100>;
+ reg-shift = <2>;
+ reg-io-width = <1>;
+ clocks = <&cnm_clock>;
+ status = "disabled";
+ };
+
+ uart2: serial@12200 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x12200 0x100>;
+ reg-shift = <2>;
+ reg-io-width = <1>;
+ clocks = <&cnm_clock>;
+ status = "disabled";
+ };
+
+ uart3: serial@12300 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x12300 0x100>;
+ reg-shift = <2>;
+ reg-io-width = <1>;
+ clocks = <&cnm_clock>;
+ status = "disabled";
+ };
+
+ mdio: mdio@22004 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "marvell,orion-mdio";
+ reg = <0x22004 0x4>;
+ clocks = <&cnm_clock>;
+ };
+
+ i2c0: i2c@11000 {
+ compatible = "marvell,mv78230-i2c";
+ reg = <0x11000 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ clocks = <&cnm_clock>;
+ clock-names = "core";
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency=<100000>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@11100 {
+ compatible = "marvell,mv78230-i2c";
+ reg = <0x11100 0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ clocks = <&cnm_clock>;
+ clock-names = "core";
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ clock-frequency=<100000>;
+ status = "disabled";
+ };
+
+ gpio0: gpio@18100 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18100 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "okay";
+ };
+
+ gpio1: gpio@18140 {
+ reg = <0x18140 0x40>;
+ compatible = "marvell,orion-gpio";
+ ngpios = <14>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ status = "okay";
+ };
+ };
+
+ /*
+ * Dedicated section for devices behind 32bit controllers so we
+ * can configure specific DMA mapping for them
+ */
+ behind-32bit-controller@7f000000 {
+ compatible = "simple-bus";
+ #address-cells = <0x2>;
+ #size-cells = <0x2>;
+ ranges = <0x0 0x0 0x0 0x7f000000 0x0 0x1000000>;
+ /* Host phy ram starts at 0x200M */
+ dma-ranges = <0x0 0x0 0x2 0x0 0x1 0x0>;
+ dma-coherent;
+
+ eth0: ethernet@20000 {
+ compatible = "marvell,armada-ac5-neta";
+ reg = <0x0 0x20000 0x0 0x4000>;
+ dma-ranges = <0 2 0 0x40000000>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cnm_clock>;
+ phy-mode = "sgmii";
+ status = "disabled";
+ };
+
+ eth1: ethernet@24000 {
+ compatible = "marvell,armada-ac5-neta";
+ reg = <0x0 0x24000 0x0 0x4000>;
+ dma-ranges = <0 2 0 0x40000000>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cnm_clock>;
+ phy-mode = "sgmii";
+ status = "disabled";
+ };
+
+ usb0: usb@80000 {
+ compatible = "marvell,ac5-ehci";
+ reg = <0x0 0x80000 0x0 0x500>;
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ usb1: usb@a0000 {
+ compatible = "marvell,ac5-ehci";
+ reg = <0x0 0xa0000 0x0 0x500>;
+ interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+ };
+
+ pinctrl0: pinctrl@80020100 {
+ compatible = "marvell,mvebu-pinctrl";
+ reg = <0 0x80020100 0 0x20>;
+ pin-count = <46>;
+ max-func = <0xf>;
+ status = "okay";
+ };
+
+ spi0: spi@805a0000 {
+ compatible = "marvell,armada-3700-spi";
+ reg = <0x0 0x805a0000 0x0 0x50>;
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ clocks = <&spi_clock>;
+ interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+ num-cs = <1>;
+ status = "disabled";
+ };
+
+ spi1: spi@805a8000 {
+ compatible = "marvell,armada-3700-spi";
+ reg = <0x0 0x805a8000 0x0 0x50>;
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ clocks = <&spi_clock>;
+ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+ num-cs = <1>;
+ status = "disabled";
+ };
+
+ gic: interrupt-controller@80600000 {
+ compatible = "arm,gic-v3";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x0 0x80600000 0x0 0x10000>, /* GICD */
+ <0x0 0x80660000 0x0 0x40000>; /* GICR */
+ interrupts = <GIC_PPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
+
+ clocks {
+ cnm_clock: cnm-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <328000000>;
+ };
+
+ spi_clock: spi-clock {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <200000000>;
+ };
+ };
+};
diff --git a/arch/arm/dts/ac5-98dx35xx.dtsi b/arch/arm/dts/ac5-98dx35xx.dtsi
new file mode 100644
index 0000000000..2ab72f854b
--- /dev/null
+++ b/arch/arm/dts/ac5-98dx35xx.dtsi
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree For AC5X.
+ *
+ * Copyright (C) 2022 Allied Telesis Labs
+ */
+
+#include "ac5-98dx25xx.dtsi"
+
+/ {
+ model = "Marvell AC5X SoC";
+ compatible = "marvell,ac5x", "marvell,ac5";
+};
+
+&cnm_clock {
+ clock-frequency = <325000000>;
+};
diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index a81b8e2b0d..400a308985 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -49,6 +49,11 @@ config ARMADA_8K
bool
select ARM64
+config ALLEYCAT_5
+ bool
+ select ARM64
+ select HAVE_MVEBU_EFUSE
+
# Armada PLL frequency (used for NAND clock generation)
config SYS_MVEBU_PLL_CLOCK
int
diff --git a/arch/arm/mach-mvebu/Makefile b/arch/arm/mach-mvebu/Makefile
index 103e64cf20..f7d7f5f8ef 100644
--- a/arch/arm/mach-mvebu/Makefile
+++ b/arch/arm/mach-mvebu/Makefile
@@ -6,6 +6,7 @@ ifdef CONFIG_ARM64
obj-$(CONFIG_ARMADA_3700) += armada3700/
obj-$(CONFIG_ARMADA_8K) += armada8k/
+obj-$(CONFIG_ALLEYCAT_5) += alleycat5/
obj-y += arm64-common.o
else # CONFIG_ARM64
diff --git a/arch/arm/mach-mvebu/alleycat5/Makefile b/arch/arm/mach-mvebu/alleycat5/Makefile
new file mode 100644
index 0000000000..43b8b70c84
--- /dev/null
+++ b/arch/arm/mach-mvebu/alleycat5/Makefile
@@ -0,0 +1,9 @@
+#
+# Copyright (C) 2016 Stefan Roese <sr@denx.de>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y = cpu.o
+obj-y += soc.o
+obj-y += clock.o
diff --git a/arch/arm/mach-mvebu/alleycat5/clock.c b/arch/arm/mach-mvebu/alleycat5/clock.c
new file mode 100644
index 0000000000..83c01daa2d
--- /dev/null
+++ b/arch/arm/mach-mvebu/alleycat5/clock.c
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ */
+
+#include <common.h>
+#include <mach/clock.h>
+#include <mvebu/mvebu_chip_sar.h>
+
+#define CONFIG_MSS_FREQUENCY (200 * 1000000)
+
+static u32 soc_ring_clk_get(void)
+{
+ struct sar_val sar;
+
+ mvebu_sar_value_get(SAR_AP_FABRIC_FREQ, &sar);
+ return sar.freq;
+}
+
+static u32 soc_mss_clk_get(void)
+{
+ return CONFIG_MSS_FREQUENCY;
+}
+
+static u32 soc_cpu_clk_get(void)
+{
+ struct sar_val sar;
+
+ mvebu_sar_value_get(SAR_CPU_FREQ, &sar);
+ return sar.freq;
+}
+
+static u32 soc_ddr_clk_get(void)
+{
+ struct sar_val sar;
+
+ mvebu_sar_value_get(SAR_DDR_FREQ, &sar);
+ return sar.freq;
+}
+
+void soc_print_clock_info(void)
+{
+ char buf[32];
+
+ printf("Clock: CPU %4s MHz\n", strmhz(buf, soc_cpu_clk_get()));
+ printf("\tDDR %4s MHz\n", strmhz(buf, soc_ddr_clk_get()));
+ printf("\tFABRIC %4s MHz\n", strmhz(buf, soc_ring_clk_get()));
+ printf("\tMSS %4s MHz\n", strmhz(buf, soc_mss_clk_get()));
+}
diff --git a/arch/arm/mach-mvebu/alleycat5/cpu.c b/arch/arm/mach-mvebu/alleycat5/cpu.c
new file mode 100644
index 0000000000..4ff95e8399
--- /dev/null
+++ b/arch/arm/mach-mvebu/alleycat5/cpu.c
@@ -0,0 +1,129 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <fdtdec.h>
+#include <linux/libfdt.h>
+#include <asm/io.h>
+#include <asm/system.h>
+#include <asm/arch/cpu.h>
+#include <linux/sizes.h>
+#include <asm/arch/soc.h>
+#include <asm/armv8/mmu.h>
+#include <mach/clock.h>
+#include <mach/soc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define RAM_SIZE SZ_1G
+
+static struct mm_region ac5_mem_map[] = {
+ {
+ /* RAM */
+ .phys = CONFIG_SYS_SDRAM_BASE,
+ .virt = CONFIG_SYS_SDRAM_BASE,
+ .attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) |
+ PTE_BLOCK_INNER_SHARE
+ },
+ {
+ /* MMIO regions */
+ .phys = 0x00000000,
+ .virt = 0xa0000000,
+ .size = 0x100000,
+
+ .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
+ PTE_BLOCK_NON_SHARE |
+ PTE_BLOCK_PXN | PTE_BLOCK_UXN
+ },
+ {
+ /* MMIO regions */
+ .phys = 0x100000,
+ .virt = 0x100000,
+ .size = 0x3ff00000,
+
+ .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
+ PTE_BLOCK_NON_SHARE |
+ PTE_BLOCK_PXN | PTE_BLOCK_UXN
+ },
+ {
+ /* MMIO regions */
+ .phys = 0x7F000000,
+ .virt = 0x7F000000,
+ .size = 0x21000000,
+
+ .attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
+ PTE_BLOCK_NON_SHARE |
+ PTE_BLOCK_PXN | PTE_BLOCK_UXN
+ },
+ {
+ 0,
+ }
+};
+
+struct mm_region *mem_map = ac5_mem_map;
+
+void reset_cpu(void)
+{
+}
+
+#if defined(CONFIG_DISPLAY_CPUINFO)
+int print_cpuinfo(void)
+{
+ soc_print_device_info();
+ soc_print_clock_info();
+
+ return 0;
+}
+#endif
+
+int alleycat5_dram_init(void)
+{
+#define SCRATCH_PAD_REG 0x80010018
+ int ret;
+
+ /* override DDR_FW size if DTS is set with size */
+ ret = fdtdec_setup_mem_size_base();
+ if (ret == -EINVAL)
+ gd->ram_size = readl(SCRATCH_PAD_REG) * 4ULL;
+
+ /* if DRAM size == 0, print error message */
+ if (gd->ram_size == 0) {
+ pr_err("DRAM size not initialized - check DRAM configuration\n");
+ printf("\n Using temporary DRAM size of 512MB.\n\n");
+ gd->ram_size = SZ_512M;
+ }
+
+ ac5_mem_map[0].size = gd->ram_size;
+
+ return 0;
+}
+
+int alleycat5_dram_init_banksize(void)
+{
+ /*
+ * Config single DRAM bank
+ */
+ gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+
+ gd->bd->bi_dram[0].size = gd->ram_size;
+
+ return 0;
+}
+
+int timer_init(void)
+{
+ return 0;
+}
+
+/*
+ * get_ref_clk
+ *
+ * return: reference clock in MHz
+ */
+u32 get_ref_clk(void)
+{
+ return 25;
+}
diff --git a/arch/arm/mach-mvebu/alleycat5/soc.c b/arch/arm/mach-mvebu/alleycat5/soc.c
new file mode 100644
index 0000000000..f388d4ee40
--- /dev/null
+++ b/arch/arm/mach-mvebu/alleycat5/soc.c
@@ -0,0 +1,229 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ */
+
+#include <common.h>
+#include <asm/arch-armada8k/cache_llc.h>
+#include <asm/io.h>
+#include <asm/arch/soc.h>
+#include <mvebu/mvebu_chip_sar.h>
+#include <dm/device.h>
+
+#define DEVICE_ID_REG 0x7F90004C
+#define DEVICE_ID_MASK 0xffff0
+#define REV_ID_MASK 0xf
+#define DEVICE_ID_OFFSET 4
+#define REV_ID_OFFSET 0
+
+#define AP_DEV_ID_STATUS_REG (SOC_REGS_PHY_BASE + 0x6F8240)
+#define JTAG_DEV_ID_STATUS_REG (SOC_REGS_PHY_BASE + 0x6F8244)
+#define AP_DEV_ID_STATUS_MASK 0xfff
+#define AP_DEV_REV_ID_STATUS_MASK 0xf0000000
+#define SW_REV_STATUS_OFFSET 16
+#define AP_REV_STATUS_OFFSET 28
+#define SW_REV_STATUS_MASK 0xf
+
+#define DEVICE_ID_SUB_REV (MVEBU_REGISTER(0x2400230))
+#define DEVICE_ID_SUB_REV_OFFSET 7
+#define DEVICE_ID_SUB_REV_MASK (0xffff << DEVICE_ID_SUB_REV_OFFSET)
+
+#define NF_CLOCK_SEL_MASK 0x1
+#define SOC_MUX_NAND_EN_MASK 0x1
+#define CLOCK_1Mhz 1000000
+#define AC5X_DEV_ID 0x9800
+
+struct soc_info {
+ u32 dev_id;
+ u32 rev_id;
+ char *soc_name;
+};
+
+static struct soc_info soc_info_table[] = {
+ /* Two reserved entries for unidentified devices - don't change */
+ { 0xB4FF, 0x0, "Unidentified Alleycat5"},
+ { 0x98FF, 0x0, "Unidentified Alleycat5x"},
+
+ { 0xB400, 0x2, "Alleycat5-plus 98DX2538-A2"},
+ { 0xB401, 0x2, "Alleycat5-plus 98DX2535-A2"},
+ { 0xB402, 0x2, "Alleycat5-plus 98DX2532-A2"},
+ { 0xB403, 0x2, "Alleycat5-plus 98DX2531-A2"},
+ { 0xB408, 0x2, "Alleycat5 98DX2528-A2"},
+ { 0xB409, 0x2, "Alleycat5 98DX2525-A2"},
+ { 0xB40A, 0x2, "Alleycat5 98DX2522-A2"},
+ { 0xB40B, 0x2, "Alleycat5 98DX2521-A2"},
+ { 0xB410, 0x2, "Alleycat5-lite 98DX2518-A2"},
+ { 0xB411, 0x2, "Alleycat5-lite 98DX2515-A2"},
+ { 0xB412, 0x2, "Alleycat5-lite 98DX2512-A2"},
+ { 0xB413, 0x2, "Alleycat5-lite 98DX2511-A2"},
+
+ { 0xB400, 0x1, "Alleycat5-plus 98DX2538-A1"},
+ { 0xB401, 0x1, "Alleycat5-plus 98DX2535-A1"},
+ { 0xB402, 0x1, "Alleycat5-plus 98DX2532-A1"},
+ { 0xB403, 0x1, "Alleycat5-plus 98DX2531-A1"},
+ { 0xB408, 0x1, "Alleycat5 98DX2528-A1"},
+ { 0xB409, 0x1, "Alleycat5 98DX2525-A1"},
+ { 0xB40A, 0x1, "Alleycat5 98DX2522-A1"},
+ { 0xB40B, 0x1, "Alleycat5 98DX2521-A1"},
+ { 0xB410, 0x1, "Alleycat5-lite 98DX2518-A1"},
+ { 0xB411, 0x1, "Alleycat5-lite 98DX2515-A1"},
+ { 0xB412, 0x1, "Alleycat5-lite 98DX2512-A1"},
+ { 0xB413, 0x1, "Alleycat5-lite 98DX2511-A1"},
+ { 0x9800, 0x1, "Alleycat5X 98DX3500M-A1"},
+ { 0x9806, 0x1, "Alleycat5X 98DX3501M-A1"},
+ { 0x9801, 0x1, "Alleycat5X 98DX3510M-A1"},
+ { 0x9802, 0x1, "Alleycat5X 98DX3520M-A1"},
+ { 0x9803, 0x1, "Alleycat5X 98DX3530M-A1"},
+ { 0x9804, 0x1, "Alleycat5X 98DX3540M-A1"},
+ { 0x9805, 0x1, "Alleycat5X 98DX3550M-A1"},
+ { 0x9820, 0x1, "Alleycat5X 98DX3500-A1"},
+ { 0x9826, 0x1, "Alleycat5X 98DX3501-A1"},
+ { 0x9821, 0x1, "Alleycat5X 98DX3510-A1"},
+ { 0x9861, 0x1, "Alleycat5X 98DX3510H-A1"},
+ { 0x9841, 0x1, "Alleycat5X 98DX3510MH-A1"},
+ { 0x9822, 0x1, "Alleycat5X 98DX3520-A1"},
+ { 0x9823, 0x1, "Alleycat5X 98DX3530-A1"},
+ { 0x9863, 0x1, "Alleycat5X 98DX3530H-A1"},
+ { 0x9824, 0x1, "Alleycat5X 98DX3540-A1"},
+ { 0x9825, 0x1, "Alleycat5X 98DX3550-A1"},
+
+ { 0xB400, 0x0, "Alleycat5-plus 98DX2538-A0"},
+ { 0xB401, 0x0, "Alleycat5-plus 98DX2535-A0"},
+ { 0xB402, 0x0, "Alleycat5-plus 98DX2532-A0"},
+ { 0xB403, 0x0, "Alleycat5-plus 98DX2531-A0"},
+ { 0xB408, 0x0, "Alleycat5 98DX2528-A0"},
+ { 0xB409, 0x0, "Alleycat5 98DX2525-A0"},
+ { 0xB40A, 0x0, "Alleycat5 98DX2522-A0"},
+ { 0xB40B, 0x0, "Alleycat5 98DX2521-A0"},
+ { 0xB410, 0x0, "Alleycat5-lite 98DX2518-A0"},
+ { 0xB411, 0x0, "Alleycat5-lite 98DX2515-A0"},
+ { 0xB412, 0x0, "Alleycat5-lite 98DX2512-A0"},
+ { 0xB413, 0x0, "Alleycat5-lite 98DX2511-A0"},
+ { 0x9800, 0x0, "Alleycat5X 98DX3500M-A0"},
+ { 0x9806, 0x0, "Alleycat5X 98DX3501M-A0"},
+ { 0x9801, 0x0, "Alleycat5X 98DX3510M-A0"},
+ { 0x9802, 0x0, "Alleycat5X 98DX3520M-A0"},
+ { 0x9803, 0x0, "Alleycat5X 98DX3530M-A0"},
+ { 0x9804, 0x0, "Alleycat5X 98DX3540M-A0"},
+ { 0x9805, 0x0, "Alleycat5X 98DX3550M-A0"},
+ { 0x9820, 0x0, "Alleycat5X 98DX3500-A0"},
+ { 0x9826, 0x0, "Alleycat5X 98DX3501-A0"},
+ { 0x9821, 0x0, "Alleycat5X 98DX3510-A0"},
+ { 0x9861, 0x0, "Alleycat5X 98DX3510H-A0"},
+ { 0x9841, 0x0, "Alleycat5X 98DX3510MH-A0"},
+ { 0x9822, 0x0, "Alleycat5X 98DX3520-A0"},
+ { 0x9823, 0x0, "Alleycat5X 98DX3530-A0"},
+ { 0x9863, 0x0, "Alleycat5X 98DX3530H-A0"},
+ { 0x9824, 0x0, "Alleycat5X 98DX3540-A0"},
+ { 0x9825, 0x0, "Alleycat5X 98DX3550-A0"},
+};
+
+static int get_soc_type_rev(u32 *type, u32 *rev)
+{
+ *type = (readl(DEVICE_ID_REG) & DEVICE_ID_MASK) >> DEVICE_ID_OFFSET;
+ *rev = (readl(DEVICE_ID_REG) & REV_ID_MASK) >> REV_ID_OFFSET;
+
+ return 0;
+}
+
+static int get_soc_table_index(u32 *index)
+{
+ u32 soc_type;
+ u32 rev, i, ret = 1;
+
+ *index = 0;
+ get_soc_type_rev(&soc_type, &rev);
+
+ for (i = 0; i < ARRAY_SIZE(soc_info_table) && ret != 0; i++) {
+ if (soc_type != soc_info_table[i].dev_id ||
+ rev != soc_info_table[i].rev_id)
+ continue;
+
+ *index = i;
+ ret = 0;
+ }
+
+ if (ret && ((soc_type & 0xFF00) == AC5X_DEV_ID))
+ *index = 1;
+
+ return ret;
+}
+
+static int get_soc_name(char **soc_name)
+{
+ u32 index;
+
+ get_soc_table_index(&index);
+ *soc_name = soc_info_table[index].soc_name;
+
+ return 0;
+}
+
+/* Print device's SoC name and AP & CP information */
+void soc_print_device_info(void)
+{
+ char *soc_name = NULL;
+
+ get_soc_name(&soc_name);
+
+ printf("SoC: %s\n", soc_name);
+}
+
+/* Return NAND clock in Hz */
+u32 mvebu_get_nand_clock(void)
+{
+ return 200 * 1000000;
+}
+
+int soc_early_init_f(void)
+{
+#ifdef CONFIG_MVEBU_SAR
+/* Sample at reset register init */
+ mvebu_sar_init();
+#endif
+ return 0;
+}
+
+/*
+ * Override of __weak int mach_cpu_init(void) :
+ * SoC/machine dependent CPU setup
+ */
+int mach_cpu_init(void)
+{
+ u32 phy_i;
+ u64 newVal, phyBase = 0x7F080800;
+
+ /* Init USB PHY */
+#define USB_STEPPING 0x20000
+#define WRITE_MASK(addr, mask, val) \
+ { newVal = (readl(addr) & (~(mask))) | val;\
+ writel(newVal, addr); }
+
+ for (phy_i = 0; phy_i < 2; phy_i++, phyBase += USB_STEPPING) {
+ WRITE_MASK(phyBase + 0x4, 0x3, 0x2);
+ WRITE_MASK(phyBase + 0xC, 0x3000000, 0x2000000);
+ WRITE_MASK(phyBase + 0x1C, 0x3, 0x2);
+ WRITE_MASK(phyBase + 0x0, 0x1FF007F, 0x600005);
+ WRITE_MASK(phyBase + 0xC, 0x000F000, 0x0002000);
+ /* Calibration Threshold Setting = 4*/
+ WRITE_MASK(phyBase + 0x8, 0x700, 0x400)
+ WRITE_MASK(phyBase + 0x14, 0x000000F, 0x000000a);
+ /* Change AMP to 4*/
+ WRITE_MASK(phyBase + 0xC, 0x3700000, 0x3400000);
+ WRITE_MASK(phyBase + 0x4, 0x3, 0x3);
+ /* Impedance calibration triggering is performed by USB probe */
+ }
+
+ return 0;
+}
+
+#ifdef CONFIG_ARCH_MISC_INIT
+int arch_misc_init(void)
+{
+ u32 type, rev;
+
+ get_soc_type_rev(&type, &rev);
+
+ return 0;
+}
+#endif
diff --git a/arch/arm/mach-mvebu/arm64-common.c b/arch/arm/mach-mvebu/arm64-common.c
index 238edbe6ba..c9b6f16c63 100644
--- a/arch/arm/mach-mvebu/arm64-common.c
+++ b/arch/arm/mach-mvebu/arm64-common.c
@@ -53,6 +53,8 @@ __weak int dram_init_banksize(void)
return a8k_dram_init_banksize();
else if (CONFIG_IS_ENABLED(ARMADA_3700))
return a3700_dram_init_banksize();
+ else if (CONFIG_IS_ENABLED(ALLEYCAT_5))
+ return alleycat5_dram_init_banksize();
else
return fdtdec_setup_memory_banksize();
}
@@ -68,6 +70,9 @@ __weak int dram_init(void)
if (CONFIG_IS_ENABLED(ARMADA_3700))
return a3700_dram_init();
+ if (CONFIG_IS_ENABLED(ALLEYCAT_5))
+ return alleycat5_dram_init();
+
if (fdtdec_setup_mem_size_base() != 0)
return -EINVAL;
@@ -100,6 +105,16 @@ int arch_early_init_r(void)
break;
}
+ i = 0;
+ while (1) {
+ /* Call the pinctrl code via the PINCTRL uclass driver */
+ ret = uclass_get_device(UCLASS_PINCTRL, i++, &dev);
+
+ /* We're done, once no further CP110 device is found */
+ if (ret)
+ break;
+ }
+
/* Cause the SATA device to do its early init */
uclass_first_device(UCLASS_AHCI, &dev);
diff --git a/arch/arm/mach-mvebu/include/mach/clock.h b/arch/arm/mach-mvebu/include/mach/clock.h
new file mode 100644
index 0000000000..93d965ad5a
--- /dev/null
+++ b/arch/arm/mach-mvebu/include/mach/clock.h
@@ -0,0 +1,11 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ */
+
+#ifndef _MVEBU_CLOCK_H_
+#define _MVEBU_CLOCK_H_
+
+void soc_print_clock_info(void);
+
+#endif /* _MVEBU_CLOCK_H_ */
diff --git a/arch/arm/mach-mvebu/include/mach/cpu.h b/arch/arm/mach-mvebu/include/mach/cpu.h
index b127fce865..c17c2440f1 100644
--- a/arch/arm/mach-mvebu/include/mach/cpu.h
+++ b/arch/arm/mach-mvebu/include/mach/cpu.h
@@ -174,6 +174,10 @@ int a3700_dram_init_banksize(void);
/* A3700 PCIe regions fixer for device tree */
int a3700_fdt_fix_pcie_regions(void *blob);
+/* Alleycat5 dram functions */
+int alleycat5_dram_init(void);
+int alleycat5_dram_init_banksize(void);
+
/*
* get_ref_clk
*
diff --git a/arch/arm/mach-mvebu/include/mach/soc.h b/arch/arm/mach-mvebu/include/mach/soc.h
index 3b9618852c..b9312e37dc 100644
--- a/arch/arm/mach-mvebu/include/mach/soc.h
+++ b/arch/arm/mach-mvebu/include/mach/soc.h
@@ -212,4 +212,8 @@
#define CONFIG_SYS_TCLK 250000000 /* 250MHz */
#endif
+#ifndef __ASSEMBLY__
+void soc_print_device_info(void);
+int soc_early_init_f(void);
+#endif /* __ASSEMBLY__ */
#endif /* _MVEBU_SOC_H */
--
2.37.3
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v2 6/6] arm: mvebu: Add RD-AC5X board
2022-09-20 8:31 [PATCH v2 0/6] arm: mvebu: Support for 98DX25xx/98DX35xx (AlleyCat5) Chris Packham
` (4 preceding siblings ...)
2022-09-20 8:31 ` [PATCH v2 5/6] arm: mvebu: Support for 98DX25xx/98DX35xx SoC Chris Packham
@ 2022-09-20 8:31 ` Chris Packham
2022-09-20 11:10 ` Pali Rohár
5 siblings, 1 reply; 17+ messages in thread
From: Chris Packham @ 2022-09-20 8:31 UTC (permalink / raw)
To: Stefan Roese
Cc: Elad Nachman, Vadym Kochan, Chris Packham, Andre Przywara,
Chris Packham, Christian Hewitt, Marcel Ziswiler, Marek Vasut,
Pali Rohár, Samuel Holland, Simon Glass, Tom Rini,
Ying-Chun Liu (PaulLiu),
u-boot
The RD-AC5X-32G16HVG6HLG-A0 development board main components and features include:
* Main 12V/54V power supply
* 270 Gbps throughput packet processor on the main board
* DDR4:
* SR1: 2GB DDR4 2400MT/S(1GB x 2 pcs ) with ECC(1GB x 1 pcs)
* SR2: 4GB DDR4 2400MT/S(2GB x 2 pcs ) with ECC(2GB x 1 pcs)
* PCB co-layout with 4GB device to support 8GB (Dual CS) requirement
* 16GB eMMC (Samsung KLMAG1JETD-B041006)
* 16MB SPI NOR(GD25Q127C)
* 32 x 1000 Base-T interfaces
* 16 x 2500 Base-T interfaces
* SR1: 88E2540*4
* SR2: 88E2580*1+88E2540*2
* Six (6) x 25G Base-R SFP28 interfaces
* One (1) x RJ-45 console connector, interfacing to the on board UART
* One (1) x USB Type-A connector, interfacing to the USB 2.0 port (0)
* One (1) x USB Type-mini B connector, interfacing to the USB 2.0 port (1)
* One (1) x RJ-45 1G Base-T Management port, interfacing to the host port (shared with PCIe)
Connected to 88E1512 Gigabit Ethernet Phy
* One (1) x Oculink port, interfacing to the PCIe port for external CPU connection
* POE 802.3AT support on Port 1 ~ Port 32, 802.3BT support on Port 33 ~ Port 48
(Microsemi PD69208T4, PD69208M or TI TPS2388,TPS23881 solution)
* POE total power budget 780W
* LED interfaces per network port/POE
* LED interfaces (common) showing system status
* PTP TC mode Supported (Reserved M.2 connector to support BC mode)
Signed-off-by: Chris Packham <judge.packham@gmail.com>
---
Changes in v2:
- Use distro boot by default
- remove unnecessary SPI-NOR partitions
arch/arm/dts/Makefile | 3 +-
arch/arm/dts/ac5-98dx35xx-rd.dts | 140 +++++++++++++++++++++
arch/arm/mach-mvebu/Kconfig | 9 +-
board/Marvell/mvebu_alleycat-5/MAINTAINERS | 6 +
board/Marvell/mvebu_alleycat-5/Makefile | 3 +
board/Marvell/mvebu_alleycat-5/board.c | 35 ++++++
configs/mvebu_ac5_rd_defconfig | 88 +++++++++++++
include/configs/mvebu_alleycat-5.h | 71 +++++++++++
8 files changed, 353 insertions(+), 2 deletions(-)
create mode 100644 arch/arm/dts/ac5-98dx35xx-rd.dts
create mode 100644 board/Marvell/mvebu_alleycat-5/MAINTAINERS
create mode 100644 board/Marvell/mvebu_alleycat-5/Makefile
create mode 100644 board/Marvell/mvebu_alleycat-5/board.c
create mode 100644 configs/mvebu_ac5_rd_defconfig
create mode 100644 include/configs/mvebu_alleycat-5.h
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 7330121dba..a334596ada 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -274,7 +274,8 @@ dtb-$(CONFIG_ARCH_MVEBU) += \
cn9132-db-A.dtb \
cn9132-db-B.dtb \
cn9130-crb-A.dtb \
- cn9130-crb-B.dtb
+ cn9130-crb-B.dtb \
+ ac5-98dx35xx-rd.dtb
endif
dtb-$(CONFIG_ARCH_SYNQUACER) += synquacer-sc2a11-developerbox.dtb
diff --git a/arch/arm/dts/ac5-98dx35xx-rd.dts b/arch/arm/dts/ac5-98dx35xx-rd.dts
new file mode 100644
index 0000000000..3b747e722e
--- /dev/null
+++ b/arch/arm/dts/ac5-98dx35xx-rd.dts
@@ -0,0 +1,140 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree For RD-AC5X.
+ *
+ * Copyright (C) 2021 Marvell
+ * Copyright (C) 2022 Allied Telesis Labs
+ */
+/*
+ * Device Tree file for Marvell Alleycat 5X development board
+ * This board file supports the B configuration of the board
+ */
+
+/dts-v1/;
+
+#include "ac5-98dx35xx.dtsi"
+
+/ {
+ model = "Marvell RD-AC5X Board";
+ compatible = "marvell,rd-ac5x", "marvell,ac5x", "marvell,ac5";
+
+ aliases {
+ serial0 = &uart0;
+ spiflash0 = &spiflash0;
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ ethernet0 = ð0;
+ ethernet1 = ð1;
+ spi0 = &spi0;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ pinctrl0 = &pinctrl0;
+ sar-reg0 = "/config-space/sar-reg";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x2 0x00000000 0x0 0x40000000>;
+ };
+
+ usb1phy: usb-phy {
+ compatible = "usb-nop-xceiv";
+ #phy-cells = <0>;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ config-space {
+ sar-reg {
+ reg = <0x944F8204 0x1>;
+ };
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&mdio {
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+ð0 {
+ status = "okay";
+ phy-handle = <&phy0>;
+};
+
+/* USB0 is a host USB */
+&usb0 {
+ status = "okay";
+};
+
+/* USB1 is a peripheral USB */
+&usb1 {
+ status = "okay";
+ phys = <&usb1phy>;
+ phy-names = "usb-phy";
+ dr_mode = "peripheral";
+};
+
+&spi0 {
+ status = "okay";
+
+ spiflash0: flash@0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <50000000>;
+ spi-tx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
+ spi-rx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
+ reg = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
+&pinctrl0 {
+ /*
+ * MPP Bus: MPP# mode#
+ * eMMC [0-11] 0x1
+ * SPI[0] [12-17] 0x1
+ * TSEN_INT [18] 0x1
+ * DEV_INIT [19] 0x1
+ * SPI[1] [20-23] 0x3
+ * UART[1] [24-25] 0x3
+ * I2C[0] [26-27] 0x1
+ * XSMI[0] [28-29] 0x1 // SCH use SMI[0], reversed due to CPSS problem
+ * SMI[1] [30-31] 0x2 // SCH use XSMI[1], reversed due to CPSS problem
+ * UART[0] [32-33] 0x1
+ * OOB_SMI [34-35] 0x1
+ * PTP_CLK0_OUT [36] 0x1
+ * PTP_PULSE_OUT [37] 0x1
+ * RCVR_CLK_OUT [38] 0x1
+ * GPIO(in/out) [39] 0x0
+ * GPIO(in/out) [40] 0x0
+ * PTP_REF_CLK [41] 0x1
+ * PTP_CLK0 [42] 0x1
+ * LED0_CLK [43] 0x1
+ * LED0_STB [44] 0x1
+ * LED0_DATA [45] 0x1
+ */
+ /* 0 1 2 3 4 5 6 7 8 9 */
+ pin-func = < 1 1 1 1 1 1 1 1 1 1
+ 1 1 1 1 1 1 1 1 1 1
+ 3 3 3 3 3 3 1 1 1 1
+ 2 2 1 1 1 1 1 1 1 0
+ 0 1 1 1 1 1 >;
+};
diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index 400a308985..d27c45d58f 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -98,7 +98,7 @@ config CUSTOMER_BOARD_SUPPORT
bool
choice
- prompt "Armada XP/375/38x/3700/7K/8K board select"
+ prompt "Armada XP/375/38x/3700/7K/8K/Alleycat-5 board select"
optional
config TARGET_CLEARFOG
@@ -150,6 +150,10 @@ config TARGET_MVEBU_ARMADA_8K
select BOARD_LATE_INIT
imply SCSI
+config TARGET_MVEBU_ALLEYCAT5
+ bool "Support AlleyCat 5 platforms"
+ select ALLEYCAT_5
+
config TARGET_OCTEONTX2_CN913x
bool "Support CN913x platforms"
select ARMADA_8K
@@ -258,6 +262,7 @@ config SYS_BOARD
default "x530" if TARGET_X530
default "db-xc3-24g4xg" if TARGET_DB_XC3_24G4XG
default "crs3xx-98dx3236" if TARGET_CRS3XX_98DX3236
+ default "mvebu_alleycat-5" if TARGET_MVEBU_ALLEYCAT5
config SYS_CONFIG_NAME
default "clearfog" if TARGET_CLEARFOG
@@ -278,6 +283,7 @@ config SYS_CONFIG_NAME
default "x530" if TARGET_X530
default "db-xc3-24g4xg" if TARGET_DB_XC3_24G4XG
default "crs3xx-98dx3236" if TARGET_CRS3XX_98DX3236
+ default "mvebu_alleycat-5" if TARGET_MVEBU_ALLEYCAT5
config SYS_VENDOR
default "Marvell" if TARGET_DB_MV784MP_GP
@@ -297,6 +303,7 @@ config SYS_VENDOR
default "gdsys" if TARGET_CONTROLCENTERDC
default "alliedtelesis" if TARGET_X530
default "mikrotik" if TARGET_CRS3XX_98DX3236
+ default "Marvell" if TARGET_MVEBU_ALLEYCAT5
config SYS_SOC
default "mvebu"
diff --git a/board/Marvell/mvebu_alleycat-5/MAINTAINERS b/board/Marvell/mvebu_alleycat-5/MAINTAINERS
new file mode 100644
index 0000000000..480c07c5f0
--- /dev/null
+++ b/board/Marvell/mvebu_alleycat-5/MAINTAINERS
@@ -0,0 +1,6 @@
+RD-AC5X BOARD
+M: Chris Packham <chris.packham@alliedtelesis.co.nz>
+S: Maintained
+F: board/Marvell/mvebu_alleycat-5/
+F: include/configs/mvebu_alleycat-5.h
+F: configs/mvebu_ac5_rd_defconfig
diff --git a/board/Marvell/mvebu_alleycat-5/Makefile b/board/Marvell/mvebu_alleycat-5/Makefile
new file mode 100644
index 0000000000..29254b4d64
--- /dev/null
+++ b/board/Marvell/mvebu_alleycat-5/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0+
+
+obj-y := board.o
diff --git a/board/Marvell/mvebu_alleycat-5/board.c b/board/Marvell/mvebu_alleycat-5/board.c
new file mode 100644
index 0000000000..3303d3c2c9
--- /dev/null
+++ b/board/Marvell/mvebu_alleycat-5/board.c
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+#include <common.h>
+#include <asm/global_data.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+__weak int soc_early_init_f(void)
+{
+ return 0;
+}
+
+int board_early_init_f(void)
+{
+ soc_early_init_f();
+
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+ return 0;
+}
+
+int board_init(void)
+{
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+ return 0;
+}
+
+int board_late_init(void)
+{
+ return 0;
+}
diff --git a/configs/mvebu_ac5_rd_defconfig b/configs/mvebu_ac5_rd_defconfig
new file mode 100644
index 0000000000..b87d337e26
--- /dev/null
+++ b/configs/mvebu_ac5_rd_defconfig
@@ -0,0 +1,88 @@
+CONFIG_ARM=y
+CONFIG_ARCH_CPU_INIT=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_SYS_TEXT_BASE=0x200000000
+CONFIG_SYS_MALLOC_LEN=0x900000
+CONFIG_TARGET_MVEBU_ALLEYCAT5=y
+CONFIG_ENV_SIZE=0x10000
+CONFIG_ENV_OFFSET=0x400000
+CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_DM_GPIO=y
+CONFIG_DEBUG_UART_BASE=0x7f012000
+CONFIG_DEBUG_UART_CLOCK=325000000
+CONFIG_SYS_LOAD_ADDR=0x202000000
+CONFIG_DEBUG_UART=y
+CONFIG_SYS_MEMTEST_START=0x200800000
+CONFIG_SYS_MEMTEST_END=0x200ffffff
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x200FF0000
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_FIT=y
+CONFIG_BOOTDELAY=-1
+CONFIG_SYS_CONSOLE_ENV_OVERWRITE=y
+CONFIG_SYS_CONSOLE_INFO_QUIET=y
+CONFIG_ARCH_EARLY_INIT_R=y
+CONFIG_ARCH_MISC_INIT=y
+CONFIG_BOARD_EARLY_INIT_F=y
+CONFIG_CMD_BOOTZ=y
+CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=10
+CONFIG_CMD_MEMTEST=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+# CONFIG_CMD_SETEXPR is not set
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_MVEBU_BUBT=y
+CONFIG_CMD_REGULATOR=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_UBI=y
+CONFIG_MAC_PARTITION=y
+CONFIG_OF_EMBED=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_CLK=y
+CONFIG_CLK_MVEBU=y
+CONFIG_DM_PCA953X=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_MVTWSI=y
+CONFIG_MISC=y
+CONFIG_MVEBU_SAR=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_XENON=y
+CONFIG_MTD=y
+CONFIG_SPI_FLASH_GIGADEVICE=y
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_SPANSION=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_PHY_MARVELL=y
+CONFIG_PHY_GIGE=y
+CONFIG_E1000=y
+CONFIG_MVNETA=y
+CONFIG_MVMDIO=y
+CONFIG_PCI=y
+CONFIG_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_ARMADA_8K=y
+CONFIG_DM_REGULATOR_FIXED=y
+CONFIG_DM_REGULATOR_GPIO=y
+CONFIG_DM_RTC=y
+CONFIG_DM_SCSI=y
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_DEBUG_UART_ANNOUNCE=y
+CONFIG_SYS_NS16550=y
+CONFIG_MVEBU_A3700_SPI=y
+CONFIG_DM_THERMAL=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_ETHER_ASIX88179=y
+CONFIG_USB_ETHER_MCS7830=y
+CONFIG_USB_ETHER_RTL8152=y
+CONFIG_USB_ETHER_SMSC95XX=y
diff --git a/include/configs/mvebu_alleycat-5.h b/include/configs/mvebu_alleycat-5.h
new file mode 100644
index 0000000000..a1a76ba4e1
--- /dev/null
+++ b/include/configs/mvebu_alleycat-5.h
@@ -0,0 +1,71 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2018 Marvell International Ltd
+ */
+
+#ifndef _CONFIG_MVEBU_ALLEYCAY_5_H
+#define _CONFIG_MVEBU_ALLEYCAY_5_H
+
+#include <asm/arch/soc.h>
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+
+/* additions for new ARM relocation support */
+#define CONFIG_SYS_SDRAM_BASE 0x200000000
+
+/* auto boot */
+#define CONFIG_PREBOOT
+
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
+ 115200, 230400, 460800, 921600 }
+
+/* Default Env vars */
+#define CONFIG_IPADDR 0.0.0.0 /* In order to cause an error */
+#define CONFIG_SERVERIP 0.0.0.0 /* In order to cause an error */
+#define CONFIG_NETMASK 255.255.255.0
+#define CONFIG_GATEWAYIP 0.0.0.0
+#define CONFIG_ETHPRIME "eth0"
+#define CONFIG_ROOTPATH "/srv/nfs/" /* Default Dir for NFS */
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+
+#define BOOT_TARGET_DEVICES(func) \
+ func(UBIFS, ubifs, 0, UBI, boot) \
+ func(MMC, mmc, 0) \
+ func(USB, usb, 0) \
+ func(DHCP, dhcp, na)
+
+#include <config_distro_bootcmd.h>
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ BOOTENV \
+ "kernel_addr_r=0x202000000\0" \
+ "fdt_addr_r=0x201000000\0" \
+ "ramdisk_addr_r=0x206000000\0" \
+ "fdtfile=marvell/" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
+ "netdev=eth0\0" \
+ "ethaddr=00:51:82:11:22:00\0" \
+ "eth1addr=00:51:82:11:22:01\0" \
+ "console=console=ttyS0,115200 earlycon=uart8250,mmio32,0xf0512000\0"\
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_SYS_TCLK 325000000
+
+/* tbd #define CONFIG_BOARD_EARLY_INIT_R */
+
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_MAX_CHIPS 1
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_SYS_NAND_USE_FLASH_BBT
+
+#define CONFIG_USB_MAX_CONTROLLER_COUNT (3 + 3)
+
+/* MTD support */
+#define CONFIG_MTD_DEVICE
+
+#endif /* _CONFIG_MVEBU_ALLEYCAY_5_H */
--
2.37.3
^ permalink raw reply related [flat|nested] 17+ messages in thread
* Re: [PATCH v2 2/6] usb: ehci: ehci-marvell: Support for marvell,ac5-ehci
2022-09-20 8:31 ` [PATCH v2 2/6] usb: ehci: ehci-marvell: Support for marvell,ac5-ehci Chris Packham
@ 2022-09-20 9:08 ` Pali Rohár
0 siblings, 0 replies; 17+ messages in thread
From: Pali Rohár @ 2022-09-20 9:08 UTC (permalink / raw)
To: Chris Packham
Cc: Stefan Roese, Elad Nachman, Vadym Kochan, Adam Ford,
Lukasz Majewski, Marek Behún, Marek Vasut, Weijie Gao,
u-boot
On Tuesday 20 September 2022 20:31:49 Chris Packham wrote:
> Unlike the other 64-bit mvebu SoCs the AlleyCat5 uses the older ehci
> block from the 32-bit SoCs. Adapt the ehci-marvell.c driver to cope with
> the fact that the ac5 does not have the mbus infrastructure the 32-bit
> SoCs have and ensure USB_EHCI_IS_TDI is selected.
>
> Signed-off-by: Chris Packham <judge.packham@gmail.com>
> ---
>
> (no changes since v1)
>
> drivers/usb/host/Kconfig | 1 +
> drivers/usb/host/ehci-marvell.c | 57 +++++++++++++++++++++++++++------
> 2 files changed, 48 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
> index a0f48f09a7..628078f495 100644
> --- a/drivers/usb/host/Kconfig
> +++ b/drivers/usb/host/Kconfig
> @@ -178,6 +178,7 @@ config USB_EHCI_MARVELL
> depends on ARCH_MVEBU || ARCH_KIRKWOOD || ARCH_ORION5X
> default y
> select USB_EHCI_IS_TDI if !ARM64
> + select USB_EHCI_IS_TDI if ALLEYCAT_5
Hello! Is this change correct? Because before this change it was
selected from all 32-bit mvebu SoCs and now it is selected only for AC5?
> ---help---
> Enables support for the on-chip EHCI controller on MVEBU SoCs.
>
> diff --git a/drivers/usb/host/ehci-marvell.c b/drivers/usb/host/ehci-marvell.c
> index b7e60c690a..7d859b9cce 100644
> --- a/drivers/usb/host/ehci-marvell.c
> +++ b/drivers/usb/host/ehci-marvell.c
> @@ -48,12 +48,17 @@ struct ehci_mvebu_priv {
> fdt_addr_t hcd_base;
> };
>
> +#define USB_TO_DRAM_TARGET_ID 0x2
> +#define USB_TO_DRAM_ATTR_ID 0x0
> +#define USB_DRAM_BASE 0x00000000
> +#define USB_DRAM_SIZE 0xfff /* don't overrun u-boot source (was 0xffff) */
> +
> /*
> * Once all the older Marvell SoC's (Orion, Kirkwood) are converted
> * to the common mvebu archticture including the mbus setup, this
> * will be the only function needed to configure the access windows
> */
> -static void usb_brg_adrdec_setup(void *base)
> +static void usb_brg_adrdec_setup(struct udevice *dev, void *base)
> {
> const struct mbus_dram_target_info *dram;
> int i;
> @@ -65,16 +70,34 @@ static void usb_brg_adrdec_setup(void *base)
> writel(0, base + USB_WINDOW_BASE(i));
> }
>
> - for (i = 0; i < dram->num_cs; i++) {
> - const struct mbus_dram_window *cs = dram->cs + i;
> + if (device_is_compatible(dev, "marvell,ac5-ehci")) {
> + /*
> + * use decoding window to map dram address seen by usb to 0x0
> + */
>
> /* Write size, attributes and target id to control register */
> - writel(((cs->size - 1) & 0xffff0000) | (cs->mbus_attr << 8) |
> - (dram->mbus_dram_target_id << 4) | 1,
> - base + USB_WINDOW_CTRL(i));
> + writel((USB_DRAM_SIZE << 16) | (USB_TO_DRAM_ATTR_ID << 8) |
> + (USB_TO_DRAM_TARGET_ID << 4) | 1,
> + base + USB_WINDOW_CTRL(0));
>
> /* Write base address to base register */
> - writel(cs->base, base + USB_WINDOW_BASE(i));
> + writel(USB_DRAM_BASE, base + USB_WINDOW_BASE(0));
> +
> + debug("## AC5 decoding windows, ctrl[%p]=0x%x, base[%p]=0x%x\n",
> + base + USB_WINDOW_CTRL(0), readl(base + USB_WINDOW_CTRL(0)),
> + base + USB_WINDOW_BASE(0), readl(base + USB_WINDOW_BASE(0)));
> + } else {
> + for (i = 0; i < dram->num_cs; i++) {
> + const struct mbus_dram_window *cs = dram->cs + i;
> +
> + /* Write size, attributes and target id to control register */
> + writel(((cs->size - 1) & 0xffff0000) | (cs->mbus_attr << 8) |
> + (dram->mbus_dram_target_id << 4) | 1,
> + base + USB_WINDOW_CTRL(i));
> +
> + /* Write base address to base register */
> + writel(cs->base, base + USB_WINDOW_BASE(i));
> + }
> }
> }
>
> @@ -126,15 +149,28 @@ static int ehci_mvebu_probe(struct udevice *dev)
> if (device_is_compatible(dev, "marvell,armada-3700-ehci"))
> marvell_ehci_ops.powerup_fixup = marvell_ehci_powerup_fixup;
> else
> - usb_brg_adrdec_setup((void *)priv->hcd_base);
> + usb_brg_adrdec_setup(dev, (void *)priv->hcd_base);
>
> hccr = (struct ehci_hccr *)(priv->hcd_base + 0x100);
> hcor = (struct ehci_hcor *)
> ((uintptr_t)hccr + HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
>
> debug("ehci-marvell: init hccr %lx and hcor %lx hc_length %ld\n",
> - (uintptr_t)hccr, (uintptr_t)hcor,
> - (uintptr_t)HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
> + (uintptr_t)hccr, (uintptr_t)hcor,
> + (uintptr_t)HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
> +
> +#define PHY_CALIB_OFFSET 0x808
> + /*
> + * Trigger calibration during each usb start/reset:
> + * BIT 13 to 0, and then to 1
> + */
> + if (device_is_compatible(dev, "marvell,ac5-ehci")) {
> + void *phy_calib_reg = (void *)(priv->hcd_base + PHY_CALIB_OFFSET);
> + u32 val = readl(phy_calib_reg) & (~BIT(13));
> +
> + writel(val, phy_calib_reg);
> + writel(val | BIT(13), phy_calib_reg);
> + }
>
> return ehci_register(dev, hccr, hcor, &marvell_ehci_ops, 0,
> USB_INIT_HOST);
> @@ -143,6 +179,7 @@ static int ehci_mvebu_probe(struct udevice *dev)
> static const struct udevice_id ehci_usb_ids[] = {
> { .compatible = "marvell,orion-ehci", },
> { .compatible = "marvell,armada-3700-ehci", },
> + { .compatible = "marvell,ac5-ehci", },
> { }
> };
>
> --
> 2.37.3
>
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v2 1/6] net: mvneta: Add support for AlleyCat5
2022-09-20 8:31 ` [PATCH v2 1/6] net: mvneta: Add support for AlleyCat5 Chris Packham
@ 2022-09-20 9:17 ` Stefan Roese
2022-09-21 1:04 ` Chris Packham
2022-09-20 10:48 ` Pali Rohár
1 sibling, 1 reply; 17+ messages in thread
From: Stefan Roese @ 2022-09-20 9:17 UTC (permalink / raw)
To: Chris Packham
Cc: Elad Nachman, Vadym Kochan, Joe Hershberger, Ramon Fried, u-boot
On 20.09.22 10:31, Chris Packham wrote:
> Add support for the AlleyCat5 SoC. This lacks the mbus from the other
> users of the mvneta.c driver so a new compatible string is needed to
> allow for a different window configuration.
>
> Signed-off-by: Chris Packham <judge.packham@gmail.com>
> ---
>
> (no changes since v1)
>
> drivers/net/Kconfig | 2 +-
> drivers/net/mvneta.c | 66 ++++++++++++++++++++++++++++++++++++++++++--
> 2 files changed, 64 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
> index 6bbbadc5ee..8df3dce6df 100644
> --- a/drivers/net/Kconfig
> +++ b/drivers/net/Kconfig
> @@ -448,7 +448,7 @@ config MVGBE
>
> config MVNETA
> bool "Marvell Armada XP/385/3700 network interface support"
> - depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
> + depends on ARMADA_XP || ARMADA_38X || ARMADA_3700 || ALLEYCAT_5
> select PHYLIB
> select DM_MDIO
> help
> diff --git a/drivers/net/mvneta.c b/drivers/net/mvneta.c
> index d2c42c4396..07919d6d35 100644
> --- a/drivers/net/mvneta.c
> +++ b/drivers/net/mvneta.c
> @@ -91,6 +91,8 @@ DECLARE_GLOBAL_DATA_PTR;
> #define MVNETA_WIN_SIZE_MASK (0xffff0000)
> #define MVNETA_BASE_ADDR_ENABLE 0x2290
> #define MVNETA_BASE_ADDR_ENABLE_BIT 0x1
> +#define MVNETA_AC5_CNM_DDR_TARGET 0x2
> +#define MVNETA_AC5_CNM_DDR_ATTR 0xb
> #define MVNETA_PORT_ACCESS_PROTECT 0x2294
> #define MVNETA_PORT_ACCESS_PROTECT_WIN0_RW 0x3
> #define MVNETA_PORT_CONFIG 0x2400
> @@ -282,6 +284,8 @@ struct mvneta_port {
> struct gpio_desc phy_reset_gpio;
> struct gpio_desc sfp_tx_disable_gpio;
> #endif
> +
> + uintptr_t dma_base; /* base address for DMA address decoding */
> };
>
> /* The mvneta_tx_desc and mvneta_rx_desc structures describe the
> @@ -513,10 +517,19 @@ static void mvneta_rxq_desc_num_update(struct mvneta_port *pp,
> static struct mvneta_rx_desc *
> mvneta_rxq_next_desc_get(struct mvneta_rx_queue *rxq)
> {
> + struct mvneta_rx_desc *curr;
> int rx_desc = rxq->next_desc_to_proc;
>
> + /* validate RX descriptor */
> + curr = rxq->descs + rx_desc;
> + if (curr->data_size == 0) {
> + /* do it to read real descriptor next time */
> + DSB;
> + return NULL;
> + }
> +
> rxq->next_desc_to_proc = MVNETA_QUEUE_NEXT_DESC(rxq, rx_desc);
> - return rxq->descs + rx_desc;
> + return curr;
> }
>
> /* Tx descriptors helper methods */
> @@ -1343,6 +1356,29 @@ static void mvneta_conf_mbus_windows(struct mvneta_port *pp)
> mvreg_write(pp, MVNETA_BASE_ADDR_ENABLE, win_enable);
> }
>
> +static void mvneta_conf_ac5_cnm_xbar_windows(struct mvneta_port *pp)
> +{
> + int i;
> +
> + /* Clear all windows */
> + for (i = 0; i < 6; i++) {
> + mvreg_write(pp, MVNETA_WIN_BASE(i), 0);
> + mvreg_write(pp, MVNETA_WIN_SIZE(i), 0);
> +
> + if (i < 4)
> + mvreg_write(pp, MVNETA_WIN_REMAP(i), 0);
> + }
> +
> + /*
> + * Setup window #0 base 0x0 to target XBAR port 2 (AMB2), attribute 0xb, size 4GB
> + * AMB2 address decoder remaps 0x0 to DDR 64 bit base address
> + */
> + mvreg_write(pp, MVNETA_WIN_BASE(0),
> + (MVNETA_AC5_CNM_DDR_ATTR << 8) | MVNETA_AC5_CNM_DDR_TARGET);
> + mvreg_write(pp, MVNETA_WIN_SIZE(0), 0xffff0000);
> + mvreg_write(pp, MVNETA_BASE_ADDR_ENABLE, 0x3e);
> +}
> +
> /* Power up the port */
> static int mvneta_port_power_up(struct mvneta_port *pp, int phy_mode)
> {
> @@ -1508,11 +1544,15 @@ static int mvneta_recv(struct udevice *dev, int flags, uchar **packetp)
> */
> rx_desc = mvneta_rxq_next_desc_get(rxq);
>
> + if (!rx_desc)
> + return 0;
> +
> rx_status = rx_desc->status;
> if (!mvneta_rxq_desc_is_first_last(rx_status) ||
> (rx_status & MVNETA_RXD_ERR_SUMMARY)) {
> mvneta_rx_error(pp, rx_desc);
> - /* leave the descriptor untouched */
> + /* invalidate the descriptor */
> + rx_desc->data_size = 0;
> return -EIO;
> }
>
> @@ -1525,13 +1565,15 @@ static int mvneta_recv(struct udevice *dev, int flags, uchar **packetp)
> * No cache invalidation needed here, since the rx_buffer's are
> * located in a uncached memory region
> */
> - *packetp = data;
> + *packetp = data + pp->dma_base;
>
> /*
> * Only mark one descriptor as free
> * since only one was processed
> */
> mvneta_rxq_desc_num_update(pp, rxq, 1, 1);
> + /* invalidate the descriptor */
> + rx_desc->data_size = 0;
> }
>
> return rx_bytes;
> @@ -1544,6 +1586,11 @@ static int mvneta_probe(struct udevice *dev)
> struct ofnode_phandle_args sfp_args;
> #endif
> void *bd_space;
> + void *blob = (void *)gd->fdt_blob;
> + int node = dev_of_offset(dev);
> + const int *cell;
> + int len;
> +
>
> /*
> * Allocate buffer area for descs and rx_buffers. This is only
> @@ -1577,9 +1624,21 @@ static int mvneta_probe(struct udevice *dev)
> /* Configure MBUS address windows */
> if (device_is_compatible(dev, "marvell,armada-3700-neta"))
> mvneta_bypass_mbus_windows(pp);
> + else if (device_is_compatible(dev, "marvell,armada-ac5-neta"))
> + mvneta_conf_ac5_cnm_xbar_windows(pp);
> else
> mvneta_conf_mbus_windows(pp);
>
> + /* fetch dma ranges property */
> + cell = fdt_getprop(blob, node, "dma-ranges", &len);
> + if (cell && len >= 4 * sizeof(int)) {
> + /* RAZA - TODO do that in loop by address-cells size */
Is this "TODO" something you wanted to address in the v2 patchset
release?
> + pp->dma_base = fdt32_to_cpu(cell[1]);
> + pp->dma_base = (pp->dma_base << 32) | fdt32_to_cpu(cell[2]);
> + } else {
> + pp->dma_base = 0;
> + }
> +
> #if CONFIG_IS_ENABLED(DM_GPIO)
> if (!dev_read_phandle_with_args(dev, "sfp", NULL, 0, 0, &sfp_args) &&
> ofnode_is_enabled(sfp_args.node))
> @@ -1620,6 +1679,7 @@ static const struct eth_ops mvneta_ops = {
>
> static const struct udevice_id mvneta_ids[] = {
> { .compatible = "marvell,armada-370-neta" },
> + { .compatible = "marvell,armada-ac5-neta" },
> { .compatible = "marvell,armada-xp-neta" },
> { .compatible = "marvell,armada-3700-neta" },
> { }
Other than the above:
Reviewed-by: Stefan Roese <sr@denx.de>
Thanks,
Stefan
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v2 5/6] arm: mvebu: Support for 98DX25xx/98DX35xx SoC
2022-09-20 8:31 ` [PATCH v2 5/6] arm: mvebu: Support for 98DX25xx/98DX35xx SoC Chris Packham
@ 2022-09-20 9:22 ` Pali Rohár
2022-09-21 3:54 ` Chris Packham
0 siblings, 1 reply; 17+ messages in thread
From: Pali Rohár @ 2022-09-20 9:22 UTC (permalink / raw)
To: Chris Packham
Cc: Stefan Roese, Elad Nachman, Vadym Kochan, Marek Behún,
Tom Rini, u-boot
On Tuesday 20 September 2022 20:31:52 Chris Packham wrote:
> Add support for the Allecat5/Alleycat5X SoC. These are L3 switches with
> an integrated CPU (referred to as the CnM block in Marvell's
> documentation). These have dual ARMv8.2 CPUs (Cortex-A55). This support
> has been ported from Marvell's SDK which is based on a much older
> version of U-Boot.
>
> Signed-off-by: Chris Packham <judge.packham@gmail.com>
> ---
>
> (no changes since v1)
>
> arch/arm/dts/ac5-98dx25xx.dtsi | 292 +++++++++++++++++++++++
> arch/arm/dts/ac5-98dx35xx.dtsi | 17 ++
> arch/arm/mach-mvebu/Kconfig | 5 +
> arch/arm/mach-mvebu/Makefile | 1 +
> arch/arm/mach-mvebu/alleycat5/Makefile | 9 +
> arch/arm/mach-mvebu/alleycat5/clock.c | 49 ++++
> arch/arm/mach-mvebu/alleycat5/cpu.c | 129 ++++++++++
> arch/arm/mach-mvebu/alleycat5/soc.c | 229 ++++++++++++++++++
> arch/arm/mach-mvebu/arm64-common.c | 15 ++
> arch/arm/mach-mvebu/include/mach/clock.h | 11 +
> arch/arm/mach-mvebu/include/mach/cpu.h | 4 +
> arch/arm/mach-mvebu/include/mach/soc.h | 4 +
> 12 files changed, 765 insertions(+)
> create mode 100644 arch/arm/dts/ac5-98dx25xx.dtsi
> create mode 100644 arch/arm/dts/ac5-98dx35xx.dtsi
> create mode 100644 arch/arm/mach-mvebu/alleycat5/Makefile
> create mode 100644 arch/arm/mach-mvebu/alleycat5/clock.c
> create mode 100644 arch/arm/mach-mvebu/alleycat5/cpu.c
> create mode 100644 arch/arm/mach-mvebu/alleycat5/soc.c
> create mode 100644 arch/arm/mach-mvebu/include/mach/clock.h
>
...
> diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
> index a81b8e2b0d..400a308985 100644
> --- a/arch/arm/mach-mvebu/Kconfig
> +++ b/arch/arm/mach-mvebu/Kconfig
> @@ -49,6 +49,11 @@ config ARMADA_8K
> bool
> select ARM64
>
> +config ALLEYCAT_5
> + bool
> + select ARM64
> + select HAVE_MVEBU_EFUSE
Hello! You are not adding any efuse implementation for AC5 platform,
so selecting this symbol seems to be wrong.
Or are you reusing A3720 or A38x OTP implementation for AC5? This is not
clear from the patch.
> +
> # Armada PLL frequency (used for NAND clock generation)
> config SYS_MVEBU_PLL_CLOCK
> int
...
> diff --git a/arch/arm/mach-mvebu/arm64-common.c b/arch/arm/mach-mvebu/arm64-common.c
> index 238edbe6ba..c9b6f16c63 100644
> --- a/arch/arm/mach-mvebu/arm64-common.c
> +++ b/arch/arm/mach-mvebu/arm64-common.c
> @@ -53,6 +53,8 @@ __weak int dram_init_banksize(void)
> return a8k_dram_init_banksize();
> else if (CONFIG_IS_ENABLED(ARMADA_3700))
> return a3700_dram_init_banksize();
> + else if (CONFIG_IS_ENABLED(ALLEYCAT_5))
> + return alleycat5_dram_init_banksize();
> else
> return fdtdec_setup_memory_banksize();
> }
> @@ -68,6 +70,9 @@ __weak int dram_init(void)
> if (CONFIG_IS_ENABLED(ARMADA_3700))
> return a3700_dram_init();
>
> + if (CONFIG_IS_ENABLED(ALLEYCAT_5))
> + return alleycat5_dram_init();
> +
> if (fdtdec_setup_mem_size_base() != 0)
> return -EINVAL;
>
> @@ -100,6 +105,16 @@ int arch_early_init_r(void)
> break;
> }
>
> + i = 0;
> + while (1) {
> + /* Call the pinctrl code via the PINCTRL uclass driver */
> + ret = uclass_get_device(UCLASS_PINCTRL, i++, &dev);
> +
> + /* We're done, once no further CP110 device is found */
> + if (ret)
> + break;
> + }
This code is unconditionally called for all 64-bit mvebu platforms, not
only for new AC5. So if this is some fix, it should be in separate
commit. If not then it should be marked AC5 specific and explained why.
> +
> /* Cause the SATA device to do its early init */
> uclass_first_device(UCLASS_AHCI, &dev);
>
> diff --git a/arch/arm/mach-mvebu/include/mach/clock.h b/arch/arm/mach-mvebu/include/mach/clock.h
> new file mode 100644
> index 0000000000..93d965ad5a
> --- /dev/null
> +++ b/arch/arm/mach-mvebu/include/mach/clock.h
> @@ -0,0 +1,11 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * Copyright (C) 2018 Marvell International Ltd.
> + */
> +
> +#ifndef _MVEBU_CLOCK_H_
> +#define _MVEBU_CLOCK_H_
> +
> +void soc_print_clock_info(void);
I'm not sure if this function needs to be exported. You are using it
only in AC5 cpu.c file, in function print_cpuinfo(). So probably you can
move soc_print_clock_info() into that file and then global mvebu clock.h
would not be needed at all.
> +
> +#endif /* _MVEBU_CLOCK_H_ */
> diff --git a/arch/arm/mach-mvebu/include/mach/cpu.h b/arch/arm/mach-mvebu/include/mach/cpu.h
> index b127fce865..c17c2440f1 100644
> --- a/arch/arm/mach-mvebu/include/mach/cpu.h
> +++ b/arch/arm/mach-mvebu/include/mach/cpu.h
> @@ -174,6 +174,10 @@ int a3700_dram_init_banksize(void);
> /* A3700 PCIe regions fixer for device tree */
> int a3700_fdt_fix_pcie_regions(void *blob);
>
> +/* Alleycat5 dram functions */
> +int alleycat5_dram_init(void);
> +int alleycat5_dram_init_banksize(void);
> +
> /*
> * get_ref_clk
> *
> diff --git a/arch/arm/mach-mvebu/include/mach/soc.h b/arch/arm/mach-mvebu/include/mach/soc.h
> index 3b9618852c..b9312e37dc 100644
> --- a/arch/arm/mach-mvebu/include/mach/soc.h
> +++ b/arch/arm/mach-mvebu/include/mach/soc.h
> @@ -212,4 +212,8 @@
> #define CONFIG_SYS_TCLK 250000000 /* 250MHz */
> #endif
>
> +#ifndef __ASSEMBLY__
> +void soc_print_device_info(void);
> +int soc_early_init_f(void);
These two functions are not available on existing mvebu platforms,
so I think functions should not be declared in global mvebu soc.h file.
> +#endif /* __ASSEMBLY__ */
> #endif /* _MVEBU_SOC_H */
> --
> 2.37.3
>
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v2 4/6] misc: mvebu: Add sample at reset driver
2022-09-20 8:31 ` [PATCH v2 4/6] misc: mvebu: Add sample at reset driver Chris Packham
@ 2022-09-20 10:42 ` Pali Rohár
0 siblings, 0 replies; 17+ messages in thread
From: Pali Rohár @ 2022-09-20 10:42 UTC (permalink / raw)
To: Chris Packham
Cc: Stefan Roese, Elad Nachman, Vadym Kochan, Alice Guo, Jim Liu,
Keerthy, Marek Vasut, Michael Scott, Michael Walle, Peng Fan,
Sean Anderson, Simon Glass, Tom Rini, Ye Li, u-boot
On Tuesday 20 September 2022 20:31:51 Chris Packham wrote:
> diff --git a/lib/fdtdec.c b/lib/fdtdec.c
> index 96b6b71a60..26e5c82bcd 100644
> --- a/lib/fdtdec.c
> +++ b/lib/fdtdec.c
> @@ -74,7 +74,11 @@ static const char * const compat_names[COMPAT_COUNT] = {
> COMPAT(ALTERA_SOCFPGA_F2SDR2, "altr,socfpga-fpga2sdram2-bridge"),
> COMPAT(ALTERA_SOCFPGA_FPGA0, "altr,socfpga-a10-fpga-mgr"),
> COMPAT(ALTERA_SOCFPGA_NOC, "altr,socfpga-a10-noc"),
> - COMPAT(ALTERA_SOCFPGA_CLK_INIT, "altr,socfpga-a10-clk-init")
> + COMPAT(ALTERA_SOCFPGA_CLK_INIT, "altr,socfpga-a10-clk-init"),
> + COMPAT(MVEBU_SAR, "marvell,sample-at-reset"),
> + COMPAT(MVEBU_SAR_REG_COMMON, "marvell,sample-at-reset-common"),
> + COMPAT(MVEBU_SAR_REG_AP806, "marvell,sample-at-reset-ap806"),
> + COMPAT(MVEBU_SAR_REG_CP110, "marvell,sample-at-reset-cp110"),
> };
Hello! You should really not to extend compat_names[]. This list here is
just for old u-boot code and entries should be removed from it only.
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v2 1/6] net: mvneta: Add support for AlleyCat5
2022-09-20 8:31 ` [PATCH v2 1/6] net: mvneta: Add support for AlleyCat5 Chris Packham
2022-09-20 9:17 ` Stefan Roese
@ 2022-09-20 10:48 ` Pali Rohár
2022-09-21 1:10 ` Chris Packham
1 sibling, 1 reply; 17+ messages in thread
From: Pali Rohár @ 2022-09-20 10:48 UTC (permalink / raw)
To: Chris Packham
Cc: Stefan Roese, Elad Nachman, Vadym Kochan, Joe Hershberger,
Ramon Fried, u-boot
On Tuesday 20 September 2022 20:31:48 Chris Packham wrote:
> diff --git a/drivers/net/mvneta.c b/drivers/net/mvneta.c
> index d2c42c4396..07919d6d35 100644
> --- a/drivers/net/mvneta.c
> +++ b/drivers/net/mvneta.c
> @@ -91,6 +91,8 @@ DECLARE_GLOBAL_DATA_PTR;
> #define MVNETA_WIN_SIZE_MASK (0xffff0000)
> #define MVNETA_BASE_ADDR_ENABLE 0x2290
> #define MVNETA_BASE_ADDR_ENABLE_BIT 0x1
> +#define MVNETA_AC5_CNM_DDR_TARGET 0x2
> +#define MVNETA_AC5_CNM_DDR_ATTR 0xb
> #define MVNETA_PORT_ACCESS_PROTECT 0x2294
> #define MVNETA_PORT_ACCESS_PROTECT_WIN0_RW 0x3
> #define MVNETA_PORT_CONFIG 0x2400
> @@ -282,6 +284,8 @@ struct mvneta_port {
> struct gpio_desc phy_reset_gpio;
> struct gpio_desc sfp_tx_disable_gpio;
> #endif
> +
> + uintptr_t dma_base; /* base address for DMA address decoding */
> };
>
> /* The mvneta_tx_desc and mvneta_rx_desc structures describe the
> @@ -513,10 +517,19 @@ static void mvneta_rxq_desc_num_update(struct mvneta_port *pp,
> static struct mvneta_rx_desc *
> mvneta_rxq_next_desc_get(struct mvneta_rx_queue *rxq)
> {
> + struct mvneta_rx_desc *curr;
> int rx_desc = rxq->next_desc_to_proc;
>
> + /* validate RX descriptor */
> + curr = rxq->descs + rx_desc;
> + if (curr->data_size == 0) {
> + /* do it to read real descriptor next time */
> + DSB;
> + return NULL;
> + }
> +
> rxq->next_desc_to_proc = MVNETA_QUEUE_NEXT_DESC(rxq, rx_desc);
> - return rxq->descs + rx_desc;
> + return curr;
> }
Hello! This change looks like some fix, and not related to AC5 support.
So it should be in separate patch as it affects all mvneta platforms,
not only AC5.
> @@ -1508,11 +1544,15 @@ static int mvneta_recv(struct udevice *dev, int flags, uchar **packetp)
> */
> rx_desc = mvneta_rxq_next_desc_get(rxq);
>
> + if (!rx_desc)
> + return 0;
> +
> rx_status = rx_desc->status;
> if (!mvneta_rxq_desc_is_first_last(rx_status) ||
> (rx_status & MVNETA_RXD_ERR_SUMMARY)) {
> mvneta_rx_error(pp, rx_desc);
> - /* leave the descriptor untouched */
> + /* invalidate the descriptor */
> + rx_desc->data_size = 0;
> return -EIO;
> }
ditto.
> @@ -1525,13 +1565,15 @@ static int mvneta_recv(struct udevice *dev, int flags, uchar **packetp)
> * No cache invalidation needed here, since the rx_buffer's are
> * located in a uncached memory region
> */
> - *packetp = data;
> + *packetp = data + pp->dma_base;
>
> /*
> * Only mark one descriptor as free
> * since only one was processed
> */
> mvneta_rxq_desc_num_update(pp, rxq, 1, 1);
> + /* invalidate the descriptor */
> + rx_desc->data_size = 0;
ditto.
> }
>
> return rx_bytes;
> @@ -1544,6 +1586,11 @@ static int mvneta_probe(struct udevice *dev)
> struct ofnode_phandle_args sfp_args;
> #endif
> void *bd_space;
> + void *blob = (void *)gd->fdt_blob;
> + int node = dev_of_offset(dev);
> + const int *cell;
> + int len;
> +
>
> /*
> * Allocate buffer area for descs and rx_buffers. This is only
> @@ -1577,9 +1624,21 @@ static int mvneta_probe(struct udevice *dev)
> /* Configure MBUS address windows */
> if (device_is_compatible(dev, "marvell,armada-3700-neta"))
> mvneta_bypass_mbus_windows(pp);
> + else if (device_is_compatible(dev, "marvell,armada-ac5-neta"))
> + mvneta_conf_ac5_cnm_xbar_windows(pp);
> else
> mvneta_conf_mbus_windows(pp);
>
> + /* fetch dma ranges property */
> + cell = fdt_getprop(blob, node, "dma-ranges", &len);
> + if (cell && len >= 4 * sizeof(int)) {
> + /* RAZA - TODO do that in loop by address-cells size */
> + pp->dma_base = fdt32_to_cpu(cell[1]);
> + pp->dma_base = (pp->dma_base << 32) | fdt32_to_cpu(cell[2]);
Probably it should be better to use some function for parsing dma-ranges
instead of open-coded implementation. It is not really clear why
cell[0] and cell[3] are ignored there, if it is missing intentionally or
it is a bug.
And... This should be used only for AC5, right?
> + } else {
> + pp->dma_base = 0;
> + }
> +
> #if CONFIG_IS_ENABLED(DM_GPIO)
> if (!dev_read_phandle_with_args(dev, "sfp", NULL, 0, 0, &sfp_args) &&
> ofnode_is_enabled(sfp_args.node))
> @@ -1620,6 +1679,7 @@ static const struct eth_ops mvneta_ops = {
>
> static const struct udevice_id mvneta_ids[] = {
> { .compatible = "marvell,armada-370-neta" },
> + { .compatible = "marvell,armada-ac5-neta" },
> { .compatible = "marvell,armada-xp-neta" },
> { .compatible = "marvell,armada-3700-neta" },
> { }
> --
> 2.37.3
>
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v2 6/6] arm: mvebu: Add RD-AC5X board
2022-09-20 8:31 ` [PATCH v2 6/6] arm: mvebu: Add RD-AC5X board Chris Packham
@ 2022-09-20 11:10 ` Pali Rohár
0 siblings, 0 replies; 17+ messages in thread
From: Pali Rohár @ 2022-09-20 11:10 UTC (permalink / raw)
To: Chris Packham
Cc: Stefan Roese, Elad Nachman, Vadym Kochan, Andre Przywara,
Chris Packham, Christian Hewitt, Marcel Ziswiler, Marek Vasut,
Samuel Holland, Simon Glass, Tom Rini, Ying-Chun Liu (PaulLiu),
u-boot
On Tuesday 20 September 2022 20:31:53 Chris Packham wrote:
> The RD-AC5X-32G16HVG6HLG-A0 development board main components and features include:
> * Main 12V/54V power supply
> * 270 Gbps throughput packet processor on the main board
> * DDR4:
> * SR1: 2GB DDR4 2400MT/S(1GB x 2 pcs ) with ECC(1GB x 1 pcs)
> * SR2: 4GB DDR4 2400MT/S(2GB x 2 pcs ) with ECC(2GB x 1 pcs)
> * PCB co-layout with 4GB device to support 8GB (Dual CS) requirement
> * 16GB eMMC (Samsung KLMAG1JETD-B041006)
> * 16MB SPI NOR(GD25Q127C)
> * 32 x 1000 Base-T interfaces
> * 16 x 2500 Base-T interfaces
> * SR1: 88E2540*4
> * SR2: 88E2580*1+88E2540*2
> * Six (6) x 25G Base-R SFP28 interfaces
> * One (1) x RJ-45 console connector, interfacing to the on board UART
> * One (1) x USB Type-A connector, interfacing to the USB 2.0 port (0)
> * One (1) x USB Type-mini B connector, interfacing to the USB 2.0 port (1)
> * One (1) x RJ-45 1G Base-T Management port, interfacing to the host port (shared with PCIe)
> Connected to 88E1512 Gigabit Ethernet Phy
> * One (1) x Oculink port, interfacing to the PCIe port for external CPU connection
> * POE 802.3AT support on Port 1 ~ Port 32, 802.3BT support on Port 33 ~ Port 48
> (Microsemi PD69208T4, PD69208M or TI TPS2388,TPS23881 solution)
> * POE total power budget 780W
> * LED interfaces per network port/POE
> * LED interfaces (common) showing system status
> * PTP TC mode Supported (Reserved M.2 connector to support BC mode)
>
> Signed-off-by: Chris Packham <judge.packham@gmail.com>
> ---
>
> Changes in v2:
> - Use distro boot by default
> - remove unnecessary SPI-NOR partitions
>
> arch/arm/dts/Makefile | 3 +-
> arch/arm/dts/ac5-98dx35xx-rd.dts | 140 +++++++++++++++++++++
> arch/arm/mach-mvebu/Kconfig | 9 +-
> board/Marvell/mvebu_alleycat-5/MAINTAINERS | 6 +
> board/Marvell/mvebu_alleycat-5/Makefile | 3 +
> board/Marvell/mvebu_alleycat-5/board.c | 35 ++++++
> configs/mvebu_ac5_rd_defconfig | 88 +++++++++++++
> include/configs/mvebu_alleycat-5.h | 71 +++++++++++
> 8 files changed, 353 insertions(+), 2 deletions(-)
> create mode 100644 arch/arm/dts/ac5-98dx35xx-rd.dts
> create mode 100644 board/Marvell/mvebu_alleycat-5/MAINTAINERS
> create mode 100644 board/Marvell/mvebu_alleycat-5/Makefile
> create mode 100644 board/Marvell/mvebu_alleycat-5/board.c
> create mode 100644 configs/mvebu_ac5_rd_defconfig
> create mode 100644 include/configs/mvebu_alleycat-5.h
>
> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> index 7330121dba..a334596ada 100644
> --- a/arch/arm/dts/Makefile
> +++ b/arch/arm/dts/Makefile
> @@ -274,7 +274,8 @@ dtb-$(CONFIG_ARCH_MVEBU) += \
> cn9132-db-A.dtb \
> cn9132-db-B.dtb \
> cn9130-crb-A.dtb \
> - cn9130-crb-B.dtb
> + cn9130-crb-B.dtb \
> + ac5-98dx35xx-rd.dtb
> endif
>
> dtb-$(CONFIG_ARCH_SYNQUACER) += synquacer-sc2a11-developerbox.dtb
> diff --git a/arch/arm/dts/ac5-98dx35xx-rd.dts b/arch/arm/dts/ac5-98dx35xx-rd.dts
> new file mode 100644
> index 0000000000..3b747e722e
> --- /dev/null
> +++ b/arch/arm/dts/ac5-98dx35xx-rd.dts
> @@ -0,0 +1,140 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree For RD-AC5X.
> + *
> + * Copyright (C) 2021 Marvell
> + * Copyright (C) 2022 Allied Telesis Labs
> + */
> +/*
> + * Device Tree file for Marvell Alleycat 5X development board
> + * This board file supports the B configuration of the board
> + */
> +
> +/dts-v1/;
> +
> +#include "ac5-98dx35xx.dtsi"
> +
> +/ {
> + model = "Marvell RD-AC5X Board";
> + compatible = "marvell,rd-ac5x", "marvell,ac5x", "marvell,ac5";
> +
> + aliases {
> + serial0 = &uart0;
> + spiflash0 = &spiflash0;
> + gpio0 = &gpio0;
> + gpio1 = &gpio1;
> + ethernet0 = ð0;
> + ethernet1 = ð1;
> + spi0 = &spi0;
> + i2c0 = &i2c0;
> + i2c1 = &i2c1;
> + usb0 = &usb0;
> + usb1 = &usb1;
> + pinctrl0 = &pinctrl0;
> + sar-reg0 = "/config-space/sar-reg";
> + };
> +
> + memory@0 {
> + device_type = "memory";
> + reg = <0x2 0x00000000 0x0 0x40000000>;
> + };
> +
> + usb1phy: usb-phy {
> + compatible = "usb-nop-xceiv";
> + #phy-cells = <0>;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + config-space {
> + sar-reg {
> + reg = <0x944F8204 0x1>;
> + };
> + };
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&mdio {
> + phy0: ethernet-phy@0 {
> + reg = <0>;
> + };
> +};
> +
> +&i2c0 {
> + status = "okay";
> +};
> +
> +&i2c1 {
> + status = "okay";
> +};
> +
> +ð0 {
> + status = "okay";
> + phy-handle = <&phy0>;
> +};
> +
> +/* USB0 is a host USB */
> +&usb0 {
> + status = "okay";
> +};
> +
> +/* USB1 is a peripheral USB */
> +&usb1 {
> + status = "okay";
> + phys = <&usb1phy>;
> + phy-names = "usb-phy";
> + dr_mode = "peripheral";
> +};
> +
> +&spi0 {
> + status = "okay";
> +
> + spiflash0: flash@0 {
> + compatible = "jedec,spi-nor";
> + spi-max-frequency = <50000000>;
> + spi-tx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
> + spi-rx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
> + reg = <0>;
> +
> + #address-cells = <1>;
> + #size-cells = <1>;
> + };
> +};
> +
> +&pinctrl0 {
> + /*
> + * MPP Bus: MPP# mode#
> + * eMMC [0-11] 0x1
> + * SPI[0] [12-17] 0x1
> + * TSEN_INT [18] 0x1
> + * DEV_INIT [19] 0x1
> + * SPI[1] [20-23] 0x3
> + * UART[1] [24-25] 0x3
> + * I2C[0] [26-27] 0x1
> + * XSMI[0] [28-29] 0x1 // SCH use SMI[0], reversed due to CPSS problem
> + * SMI[1] [30-31] 0x2 // SCH use XSMI[1], reversed due to CPSS problem
> + * UART[0] [32-33] 0x1
> + * OOB_SMI [34-35] 0x1
> + * PTP_CLK0_OUT [36] 0x1
> + * PTP_PULSE_OUT [37] 0x1
> + * RCVR_CLK_OUT [38] 0x1
> + * GPIO(in/out) [39] 0x0
> + * GPIO(in/out) [40] 0x0
> + * PTP_REF_CLK [41] 0x1
> + * PTP_CLK0 [42] 0x1
> + * LED0_CLK [43] 0x1
> + * LED0_STB [44] 0x1
> + * LED0_DATA [45] 0x1
> + */
> + /* 0 1 2 3 4 5 6 7 8 9 */
> + pin-func = < 1 1 1 1 1 1 1 1 1 1
> + 1 1 1 1 1 1 1 1 1 1
> + 3 3 3 3 3 3 1 1 1 1
> + 2 2 1 1 1 1 1 1 1 0
> + 0 1 1 1 1 1 >;
> +};
> diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
> index 400a308985..d27c45d58f 100644
> --- a/arch/arm/mach-mvebu/Kconfig
> +++ b/arch/arm/mach-mvebu/Kconfig
> @@ -98,7 +98,7 @@ config CUSTOMER_BOARD_SUPPORT
> bool
>
> choice
> - prompt "Armada XP/375/38x/3700/7K/8K board select"
> + prompt "Armada XP/375/38x/3700/7K/8K/Alleycat-5 board select"
> optional
>
> config TARGET_CLEARFOG
> @@ -150,6 +150,10 @@ config TARGET_MVEBU_ARMADA_8K
> select BOARD_LATE_INIT
> imply SCSI
>
> +config TARGET_MVEBU_ALLEYCAT5
> + bool "Support AlleyCat 5 platforms"
> + select ALLEYCAT_5
> +
> config TARGET_OCTEONTX2_CN913x
> bool "Support CN913x platforms"
> select ARMADA_8K
> @@ -258,6 +262,7 @@ config SYS_BOARD
> default "x530" if TARGET_X530
> default "db-xc3-24g4xg" if TARGET_DB_XC3_24G4XG
> default "crs3xx-98dx3236" if TARGET_CRS3XX_98DX3236
> + default "mvebu_alleycat-5" if TARGET_MVEBU_ALLEYCAT5
>
> config SYS_CONFIG_NAME
> default "clearfog" if TARGET_CLEARFOG
> @@ -278,6 +283,7 @@ config SYS_CONFIG_NAME
> default "x530" if TARGET_X530
> default "db-xc3-24g4xg" if TARGET_DB_XC3_24G4XG
> default "crs3xx-98dx3236" if TARGET_CRS3XX_98DX3236
> + default "mvebu_alleycat-5" if TARGET_MVEBU_ALLEYCAT5
>
> config SYS_VENDOR
> default "Marvell" if TARGET_DB_MV784MP_GP
> @@ -297,6 +303,7 @@ config SYS_VENDOR
> default "gdsys" if TARGET_CONTROLCENTERDC
> default "alliedtelesis" if TARGET_X530
> default "mikrotik" if TARGET_CRS3XX_98DX3236
> + default "Marvell" if TARGET_MVEBU_ALLEYCAT5
>
> config SYS_SOC
> default "mvebu"
> diff --git a/board/Marvell/mvebu_alleycat-5/MAINTAINERS b/board/Marvell/mvebu_alleycat-5/MAINTAINERS
> new file mode 100644
> index 0000000000..480c07c5f0
> --- /dev/null
> +++ b/board/Marvell/mvebu_alleycat-5/MAINTAINERS
> @@ -0,0 +1,6 @@
> +RD-AC5X BOARD
> +M: Chris Packham <chris.packham@alliedtelesis.co.nz>
> +S: Maintained
> +F: board/Marvell/mvebu_alleycat-5/
> +F: include/configs/mvebu_alleycat-5.h
> +F: configs/mvebu_ac5_rd_defconfig
> diff --git a/board/Marvell/mvebu_alleycat-5/Makefile b/board/Marvell/mvebu_alleycat-5/Makefile
> new file mode 100644
> index 0000000000..29254b4d64
> --- /dev/null
> +++ b/board/Marvell/mvebu_alleycat-5/Makefile
> @@ -0,0 +1,3 @@
> +# SPDX-License-Identifier: GPL-2.0+
> +
> +obj-y := board.o
> diff --git a/board/Marvell/mvebu_alleycat-5/board.c b/board/Marvell/mvebu_alleycat-5/board.c
> new file mode 100644
> index 0000000000..3303d3c2c9
> --- /dev/null
> +++ b/board/Marvell/mvebu_alleycat-5/board.c
> @@ -0,0 +1,35 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +
> +#include <common.h>
> +#include <asm/global_data.h>
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +__weak int soc_early_init_f(void)
> +{
> + return 0;
> +}
> +
> +int board_early_init_f(void)
> +{
> + soc_early_init_f();
> +
> + return 0;
> +}
> +
> +int board_early_init_r(void)
> +{
> + return 0;
> +}
> +
> +int board_init(void)
> +{
> + gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
> +
> + return 0;
> +}
> +
> +int board_late_init(void)
> +{
> + return 0;
> +}
> diff --git a/configs/mvebu_ac5_rd_defconfig b/configs/mvebu_ac5_rd_defconfig
> new file mode 100644
> index 0000000000..b87d337e26
> --- /dev/null
> +++ b/configs/mvebu_ac5_rd_defconfig
> @@ -0,0 +1,88 @@
> +CONFIG_ARM=y
> +CONFIG_ARCH_CPU_INIT=y
> +CONFIG_ARCH_MVEBU=y
> +CONFIG_SYS_TEXT_BASE=0x200000000
> +CONFIG_SYS_MALLOC_LEN=0x900000
> +CONFIG_TARGET_MVEBU_ALLEYCAT5=y
> +CONFIG_ENV_SIZE=0x10000
> +CONFIG_ENV_OFFSET=0x400000
> +CONFIG_ENV_SECT_SIZE=0x10000
> +CONFIG_DM_GPIO=y
> +CONFIG_DEBUG_UART_BASE=0x7f012000
> +CONFIG_DEBUG_UART_CLOCK=325000000
> +CONFIG_SYS_LOAD_ADDR=0x202000000
> +CONFIG_DEBUG_UART=y
> +CONFIG_SYS_MEMTEST_START=0x200800000
> +CONFIG_SYS_MEMTEST_END=0x200ffffff
> +CONFIG_DISTRO_DEFAULTS=y
> +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
> +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x200FF0000
> +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> +CONFIG_FIT=y
> +CONFIG_BOOTDELAY=-1
> +CONFIG_SYS_CONSOLE_ENV_OVERWRITE=y
> +CONFIG_SYS_CONSOLE_INFO_QUIET=y
> +CONFIG_ARCH_EARLY_INIT_R=y
> +CONFIG_ARCH_MISC_INIT=y
> +CONFIG_BOARD_EARLY_INIT_F=y
> +CONFIG_CMD_BOOTZ=y
> +CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS=10
> +CONFIG_CMD_MEMTEST=y
> +# CONFIG_CMD_FLASH is not set
> +CONFIG_CMD_GPIO=y
> +CONFIG_CMD_I2C=y
> +CONFIG_CMD_MMC=y
> +CONFIG_CMD_PCI=y
> +CONFIG_CMD_SPI=y
> +CONFIG_CMD_USB=y
> +# CONFIG_CMD_SETEXPR is not set
> +CONFIG_CMD_CACHE=y
> +CONFIG_CMD_TIME=y
> +CONFIG_CMD_MVEBU_BUBT=y
> +CONFIG_CMD_REGULATOR=y
> +CONFIG_CMD_EXT4_WRITE=y
> +CONFIG_CMD_UBI=y
> +CONFIG_MAC_PARTITION=y
> +CONFIG_OF_EMBED=y
> +CONFIG_ENV_IS_IN_SPI_FLASH=y
> +CONFIG_CLK=y
> +CONFIG_CLK_MVEBU=y
> +CONFIG_DM_PCA953X=y
> +CONFIG_DM_I2C=y
> +CONFIG_SYS_I2C_MVTWSI=y
> +CONFIG_MISC=y
> +CONFIG_MVEBU_SAR=y
> +CONFIG_MMC_SDHCI=y
> +CONFIG_MMC_SDHCI_XENON=y
> +CONFIG_MTD=y
> +CONFIG_SPI_FLASH_GIGADEVICE=y
> +CONFIG_SPI_FLASH_MACRONIX=y
> +CONFIG_SPI_FLASH_SPANSION=y
> +CONFIG_SPI_FLASH_STMICRO=y
> +CONFIG_PHY_MARVELL=y
> +CONFIG_PHY_GIGE=y
> +CONFIG_E1000=y
> +CONFIG_MVNETA=y
> +CONFIG_MVMDIO=y
> +CONFIG_PCI=y
> +CONFIG_PHY=y
> +CONFIG_PINCTRL=y
> +CONFIG_PINCTRL_ARMADA_8K=y
> +CONFIG_DM_REGULATOR_FIXED=y
> +CONFIG_DM_REGULATOR_GPIO=y
> +CONFIG_DM_RTC=y
> +CONFIG_DM_SCSI=y
> +CONFIG_DEBUG_UART_SHIFT=2
> +CONFIG_DEBUG_UART_ANNOUNCE=y
> +CONFIG_SYS_NS16550=y
> +CONFIG_MVEBU_A3700_SPI=y
> +CONFIG_DM_THERMAL=y
> +CONFIG_USB=y
> +CONFIG_USB_XHCI_HCD=y
> +CONFIG_USB_EHCI_HCD=y
> +CONFIG_USB_HOST_ETHER=y
> +CONFIG_USB_ETHER_ASIX=y
> +CONFIG_USB_ETHER_ASIX88179=y
> +CONFIG_USB_ETHER_MCS7830=y
> +CONFIG_USB_ETHER_RTL8152=y
> +CONFIG_USB_ETHER_SMSC95XX=y
> diff --git a/include/configs/mvebu_alleycat-5.h b/include/configs/mvebu_alleycat-5.h
> new file mode 100644
> index 0000000000..a1a76ba4e1
> --- /dev/null
> +++ b/include/configs/mvebu_alleycat-5.h
> @@ -0,0 +1,71 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/*
> + * Copyright (C) 2018 Marvell International Ltd
> + */
> +
> +#ifndef _CONFIG_MVEBU_ALLEYCAY_5_H
> +#define _CONFIG_MVEBU_ALLEYCAY_5_H
> +
> +#include <asm/arch/soc.h>
> +
> +/*
> + * High Level Configuration Options (easy to change)
> + */
> +#define CONFIG_DISPLAY_BOARDINFO_LATE
> +
> +/* additions for new ARM relocation support */
> +#define CONFIG_SYS_SDRAM_BASE 0x200000000
> +
> +/* auto boot */
> +#define CONFIG_PREBOOT
> +
> +#define CONFIG_BAUDRATE 115200
> +#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
> + 115200, 230400, 460800, 921600 }
> +
> +/* Default Env vars */
> +#define CONFIG_IPADDR 0.0.0.0 /* In order to cause an error */
> +#define CONFIG_SERVERIP 0.0.0.0 /* In order to cause an error */
> +#define CONFIG_NETMASK 255.255.255.0
> +#define CONFIG_GATEWAYIP 0.0.0.0
> +#define CONFIG_ETHPRIME "eth0"
Hello! This was already migrated to Kconfig.
> +#define CONFIG_ROOTPATH "/srv/nfs/" /* Default Dir for NFS */
> +#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
> +
> +#define BOOT_TARGET_DEVICES(func) \
> + func(UBIFS, ubifs, 0, UBI, boot) \
This is for sure wrong. You have not defined any MTD partition with
label UBI. So it would not work.
> + func(MMC, mmc, 0) \
> + func(USB, usb, 0) \
> + func(DHCP, dhcp, na)
> +
> +#include <config_distro_bootcmd.h>
> +
> +#define CONFIG_EXTRA_ENV_SETTINGS \
> + BOOTENV \
> + "kernel_addr_r=0x202000000\0" \
> + "fdt_addr_r=0x201000000\0" \
> + "ramdisk_addr_r=0x206000000\0" \
> + "fdtfile=marvell/" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
> + "netdev=eth0\0" \
You should set CONFIG_ETHPRIME in Kconfig. $netdev is already ignored
by U-Boot.
And if you have only one eth controller then setting CONFIG_ETHPRIME is
probably not needed at all.
> + "ethaddr=00:51:82:11:22:00\0" \
> + "eth1addr=00:51:82:11:22:01\0" \
Hardcoding static fixed MAC addresses into ENV looks also bad.
> + "console=console=ttyS0,115200 earlycon=uart8250,mmio32,0xf0512000\0"\
> +
> +/*
> + * High Level Configuration Options (easy to change)
> + */
> +#define CONFIG_SYS_TCLK 325000000
> +
> +/* tbd #define CONFIG_BOARD_EARLY_INIT_R */
> +
> +#define CONFIG_SYS_MAX_NAND_DEVICE 1
> +#define CONFIG_SYS_NAND_MAX_CHIPS 1
> +#define CONFIG_SYS_NAND_ONFI_DETECTION
> +#define CONFIG_SYS_NAND_USE_FLASH_BBT
> +
> +#define CONFIG_USB_MAX_CONTROLLER_COUNT (3 + 3)
> +
> +/* MTD support */
> +#define CONFIG_MTD_DEVICE
> +
> +#endif /* _CONFIG_MVEBU_ALLEYCAY_5_H */
> --
> 2.37.3
>
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v2 1/6] net: mvneta: Add support for AlleyCat5
2022-09-20 9:17 ` Stefan Roese
@ 2022-09-21 1:04 ` Chris Packham
0 siblings, 0 replies; 17+ messages in thread
From: Chris Packham @ 2022-09-21 1:04 UTC (permalink / raw)
To: Stefan Roese
Cc: Elad Nachman, Vadym Kochan, Joe Hershberger, Ramon Fried, u-boot
On Tue, Sep 20, 2022 at 9:17 PM Stefan Roese <sr@denx.de> wrote:
>
> On 20.09.22 10:31, Chris Packham wrote:
> > Add support for the AlleyCat5 SoC. This lacks the mbus from the other
> > users of the mvneta.c driver so a new compatible string is needed to
> > allow for a different window configuration.
> >
> > Signed-off-by: Chris Packham <judge.packham@gmail.com>
> > ---
> >
> > (no changes since v1)
> >
> > drivers/net/Kconfig | 2 +-
> > drivers/net/mvneta.c | 66 ++++++++++++++++++++++++++++++++++++++++++--
> > 2 files changed, 64 insertions(+), 4 deletions(-)
> >
> > diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
> > index 6bbbadc5ee..8df3dce6df 100644
> > --- a/drivers/net/Kconfig
> > +++ b/drivers/net/Kconfig
> > @@ -448,7 +448,7 @@ config MVGBE
> >
> > config MVNETA
> > bool "Marvell Armada XP/385/3700 network interface support"
> > - depends on ARMADA_XP || ARMADA_38X || ARMADA_3700
> > + depends on ARMADA_XP || ARMADA_38X || ARMADA_3700 || ALLEYCAT_5
> > select PHYLIB
> > select DM_MDIO
> > help
> > diff --git a/drivers/net/mvneta.c b/drivers/net/mvneta.c
> > index d2c42c4396..07919d6d35 100644
> > --- a/drivers/net/mvneta.c
> > +++ b/drivers/net/mvneta.c
> > @@ -91,6 +91,8 @@ DECLARE_GLOBAL_DATA_PTR;
> > #define MVNETA_WIN_SIZE_MASK (0xffff0000)
> > #define MVNETA_BASE_ADDR_ENABLE 0x2290
> > #define MVNETA_BASE_ADDR_ENABLE_BIT 0x1
> > +#define MVNETA_AC5_CNM_DDR_TARGET 0x2
> > +#define MVNETA_AC5_CNM_DDR_ATTR 0xb
> > #define MVNETA_PORT_ACCESS_PROTECT 0x2294
> > #define MVNETA_PORT_ACCESS_PROTECT_WIN0_RW 0x3
> > #define MVNETA_PORT_CONFIG 0x2400
> > @@ -282,6 +284,8 @@ struct mvneta_port {
> > struct gpio_desc phy_reset_gpio;
> > struct gpio_desc sfp_tx_disable_gpio;
> > #endif
> > +
> > + uintptr_t dma_base; /* base address for DMA address decoding */
> > };
> >
> > /* The mvneta_tx_desc and mvneta_rx_desc structures describe the
> > @@ -513,10 +517,19 @@ static void mvneta_rxq_desc_num_update(struct mvneta_port *pp,
> > static struct mvneta_rx_desc *
> > mvneta_rxq_next_desc_get(struct mvneta_rx_queue *rxq)
> > {
> > + struct mvneta_rx_desc *curr;
> > int rx_desc = rxq->next_desc_to_proc;
> >
> > + /* validate RX descriptor */
> > + curr = rxq->descs + rx_desc;
> > + if (curr->data_size == 0) {
> > + /* do it to read real descriptor next time */
> > + DSB;
> > + return NULL;
> > + }
> > +
> > rxq->next_desc_to_proc = MVNETA_QUEUE_NEXT_DESC(rxq, rx_desc);
> > - return rxq->descs + rx_desc;
> > + return curr;
> > }
> >
> > /* Tx descriptors helper methods */
> > @@ -1343,6 +1356,29 @@ static void mvneta_conf_mbus_windows(struct mvneta_port *pp)
> > mvreg_write(pp, MVNETA_BASE_ADDR_ENABLE, win_enable);
> > }
> >
> > +static void mvneta_conf_ac5_cnm_xbar_windows(struct mvneta_port *pp)
> > +{
> > + int i;
> > +
> > + /* Clear all windows */
> > + for (i = 0; i < 6; i++) {
> > + mvreg_write(pp, MVNETA_WIN_BASE(i), 0);
> > + mvreg_write(pp, MVNETA_WIN_SIZE(i), 0);
> > +
> > + if (i < 4)
> > + mvreg_write(pp, MVNETA_WIN_REMAP(i), 0);
> > + }
> > +
> > + /*
> > + * Setup window #0 base 0x0 to target XBAR port 2 (AMB2), attribute 0xb, size 4GB
> > + * AMB2 address decoder remaps 0x0 to DDR 64 bit base address
> > + */
> > + mvreg_write(pp, MVNETA_WIN_BASE(0),
> > + (MVNETA_AC5_CNM_DDR_ATTR << 8) | MVNETA_AC5_CNM_DDR_TARGET);
> > + mvreg_write(pp, MVNETA_WIN_SIZE(0), 0xffff0000);
> > + mvreg_write(pp, MVNETA_BASE_ADDR_ENABLE, 0x3e);
> > +}
> > +
> > /* Power up the port */
> > static int mvneta_port_power_up(struct mvneta_port *pp, int phy_mode)
> > {
> > @@ -1508,11 +1544,15 @@ static int mvneta_recv(struct udevice *dev, int flags, uchar **packetp)
> > */
> > rx_desc = mvneta_rxq_next_desc_get(rxq);
> >
> > + if (!rx_desc)
> > + return 0;
> > +
> > rx_status = rx_desc->status;
> > if (!mvneta_rxq_desc_is_first_last(rx_status) ||
> > (rx_status & MVNETA_RXD_ERR_SUMMARY)) {
> > mvneta_rx_error(pp, rx_desc);
> > - /* leave the descriptor untouched */
> > + /* invalidate the descriptor */
> > + rx_desc->data_size = 0;
> > return -EIO;
> > }
> >
> > @@ -1525,13 +1565,15 @@ static int mvneta_recv(struct udevice *dev, int flags, uchar **packetp)
> > * No cache invalidation needed here, since the rx_buffer's are
> > * located in a uncached memory region
> > */
> > - *packetp = data;
> > + *packetp = data + pp->dma_base;
> >
> > /*
> > * Only mark one descriptor as free
> > * since only one was processed
> > */
> > mvneta_rxq_desc_num_update(pp, rxq, 1, 1);
> > + /* invalidate the descriptor */
> > + rx_desc->data_size = 0;
> > }
> >
> > return rx_bytes;
> > @@ -1544,6 +1586,11 @@ static int mvneta_probe(struct udevice *dev)
> > struct ofnode_phandle_args sfp_args;
> > #endif
> > void *bd_space;
> > + void *blob = (void *)gd->fdt_blob;
> > + int node = dev_of_offset(dev);
> > + const int *cell;
> > + int len;
> > +
> >
> > /*
> > * Allocate buffer area for descs and rx_buffers. This is only
> > @@ -1577,9 +1624,21 @@ static int mvneta_probe(struct udevice *dev)
> > /* Configure MBUS address windows */
> > if (device_is_compatible(dev, "marvell,armada-3700-neta"))
> > mvneta_bypass_mbus_windows(pp);
> > + else if (device_is_compatible(dev, "marvell,armada-ac5-neta"))
> > + mvneta_conf_ac5_cnm_xbar_windows(pp);
> > else
> > mvneta_conf_mbus_windows(pp);
> >
> > + /* fetch dma ranges property */
> > + cell = fdt_getprop(blob, node, "dma-ranges", &len);
> > + if (cell && len >= 4 * sizeof(int)) {
> > + /* RAZA - TODO do that in loop by address-cells size */
>
> Is this "TODO" something you wanted to address in the v2 patchset
> release?
>
That's from the original Marvell code. I've no idea who Raza is or if
(s)he ever got around to doing this. Pali has other concerns with this
part so I'll try to address removing the TODO along with avoiding open
coding the parsing.
> > + pp->dma_base = fdt32_to_cpu(cell[1]);
> > + pp->dma_base = (pp->dma_base << 32) | fdt32_to_cpu(cell[2]);
> > + } else {
> > + pp->dma_base = 0;
> > + }
> > +
> > #if CONFIG_IS_ENABLED(DM_GPIO)
> > if (!dev_read_phandle_with_args(dev, "sfp", NULL, 0, 0, &sfp_args) &&
> > ofnode_is_enabled(sfp_args.node))
> > @@ -1620,6 +1679,7 @@ static const struct eth_ops mvneta_ops = {
> >
> > static const struct udevice_id mvneta_ids[] = {
> > { .compatible = "marvell,armada-370-neta" },
> > + { .compatible = "marvell,armada-ac5-neta" },
> > { .compatible = "marvell,armada-xp-neta" },
> > { .compatible = "marvell,armada-3700-neta" },
> > { }
>
> Other than the above:
>
> Reviewed-by: Stefan Roese <sr@denx.de>
>
> Thanks,
> Stefan
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v2 1/6] net: mvneta: Add support for AlleyCat5
2022-09-20 10:48 ` Pali Rohár
@ 2022-09-21 1:10 ` Chris Packham
0 siblings, 0 replies; 17+ messages in thread
From: Chris Packham @ 2022-09-21 1:10 UTC (permalink / raw)
To: Pali Rohár
Cc: Stefan Roese, Elad Nachman, Vadym Kochan, Joe Hershberger,
Ramon Fried, u-boot
On Tue, Sep 20, 2022 at 10:48 PM Pali Rohár <pali@kernel.org> wrote:
>
> On Tuesday 20 September 2022 20:31:48 Chris Packham wrote:
> > diff --git a/drivers/net/mvneta.c b/drivers/net/mvneta.c
> > index d2c42c4396..07919d6d35 100644
> > --- a/drivers/net/mvneta.c
> > +++ b/drivers/net/mvneta.c
> > @@ -91,6 +91,8 @@ DECLARE_GLOBAL_DATA_PTR;
> > #define MVNETA_WIN_SIZE_MASK (0xffff0000)
> > #define MVNETA_BASE_ADDR_ENABLE 0x2290
> > #define MVNETA_BASE_ADDR_ENABLE_BIT 0x1
> > +#define MVNETA_AC5_CNM_DDR_TARGET 0x2
> > +#define MVNETA_AC5_CNM_DDR_ATTR 0xb
> > #define MVNETA_PORT_ACCESS_PROTECT 0x2294
> > #define MVNETA_PORT_ACCESS_PROTECT_WIN0_RW 0x3
> > #define MVNETA_PORT_CONFIG 0x2400
> > @@ -282,6 +284,8 @@ struct mvneta_port {
> > struct gpio_desc phy_reset_gpio;
> > struct gpio_desc sfp_tx_disable_gpio;
> > #endif
> > +
> > + uintptr_t dma_base; /* base address for DMA address decoding */
> > };
> >
> > /* The mvneta_tx_desc and mvneta_rx_desc structures describe the
> > @@ -513,10 +517,19 @@ static void mvneta_rxq_desc_num_update(struct mvneta_port *pp,
> > static struct mvneta_rx_desc *
> > mvneta_rxq_next_desc_get(struct mvneta_rx_queue *rxq)
> > {
> > + struct mvneta_rx_desc *curr;
> > int rx_desc = rxq->next_desc_to_proc;
> >
> > + /* validate RX descriptor */
> > + curr = rxq->descs + rx_desc;
> > + if (curr->data_size == 0) {
> > + /* do it to read real descriptor next time */
> > + DSB;
> > + return NULL;
> > + }
> > +
> > rxq->next_desc_to_proc = MVNETA_QUEUE_NEXT_DESC(rxq, rx_desc);
> > - return rxq->descs + rx_desc;
> > + return curr;
> > }
>
> Hello! This change looks like some fix, and not related to AC5 support.
> So it should be in separate patch as it affects all mvneta platforms,
> not only AC5.
>
Yep. I'll see if I can get away without this change for the AC5X. So
I'll either move it to a new patch or remove it completely in the next
round.
> > @@ -1508,11 +1544,15 @@ static int mvneta_recv(struct udevice *dev, int flags, uchar **packetp)
> > */
> > rx_desc = mvneta_rxq_next_desc_get(rxq);
> >
> > + if (!rx_desc)
> > + return 0;
> > +
> > rx_status = rx_desc->status;
> > if (!mvneta_rxq_desc_is_first_last(rx_status) ||
> > (rx_status & MVNETA_RXD_ERR_SUMMARY)) {
> > mvneta_rx_error(pp, rx_desc);
> > - /* leave the descriptor untouched */
> > + /* invalidate the descriptor */
> > + rx_desc->data_size = 0;
> > return -EIO;
> > }
>
> ditto.
>
> > @@ -1525,13 +1565,15 @@ static int mvneta_recv(struct udevice *dev, int flags, uchar **packetp)
> > * No cache invalidation needed here, since the rx_buffer's are
> > * located in a uncached memory region
> > */
> > - *packetp = data;
> > + *packetp = data + pp->dma_base;
> >
> > /*
> > * Only mark one descriptor as free
> > * since only one was processed
> > */
> > mvneta_rxq_desc_num_update(pp, rxq, 1, 1);
> > + /* invalidate the descriptor */
> > + rx_desc->data_size = 0;
>
> ditto.
>
> > }
> >
> > return rx_bytes;
> > @@ -1544,6 +1586,11 @@ static int mvneta_probe(struct udevice *dev)
> > struct ofnode_phandle_args sfp_args;
> > #endif
> > void *bd_space;
> > + void *blob = (void *)gd->fdt_blob;
> > + int node = dev_of_offset(dev);
> > + const int *cell;
> > + int len;
> > +
> >
> > /*
> > * Allocate buffer area for descs and rx_buffers. This is only
> > @@ -1577,9 +1624,21 @@ static int mvneta_probe(struct udevice *dev)
> > /* Configure MBUS address windows */
> > if (device_is_compatible(dev, "marvell,armada-3700-neta"))
> > mvneta_bypass_mbus_windows(pp);
> > + else if (device_is_compatible(dev, "marvell,armada-ac5-neta"))
> > + mvneta_conf_ac5_cnm_xbar_windows(pp);
> > else
> > mvneta_conf_mbus_windows(pp);
> >
> > + /* fetch dma ranges property */
> > + cell = fdt_getprop(blob, node, "dma-ranges", &len);
> > + if (cell && len >= 4 * sizeof(int)) {
> > + /* RAZA - TODO do that in loop by address-cells size */
> > + pp->dma_base = fdt32_to_cpu(cell[1]);
> > + pp->dma_base = (pp->dma_base << 32) | fdt32_to_cpu(cell[2]);
>
> Probably it should be better to use some function for parsing dma-ranges
> instead of open-coded implementation. It is not really clear why
> cell[0] and cell[3] are ignored there, if it is missing intentionally or
> it is a bug.
>
> And... This should be used only for AC5, right?
>
I think this is about handling 32-bit DMA on a 64-bit system with RAM
that starts above the 4GB boundary. So not strictly AC5 specific but
the AC5 is the only thing that fits those criteria currently.
Certainly the AC5 is the only thing that sets the dma-ranges property
on the Ethernet controller. I did find some APIs for parsing
dma-ranges but that led me down a rabbit hole of DM_DMA which looks
like it (or the SoC) might not be ready for prime-time. I'll see what
I can do to avoid the open coding.
> > + } else {
> > + pp->dma_base = 0;
> > + }
> > +
> > #if CONFIG_IS_ENABLED(DM_GPIO)
> > if (!dev_read_phandle_with_args(dev, "sfp", NULL, 0, 0, &sfp_args) &&
> > ofnode_is_enabled(sfp_args.node))
> > @@ -1620,6 +1679,7 @@ static const struct eth_ops mvneta_ops = {
> >
> > static const struct udevice_id mvneta_ids[] = {
> > { .compatible = "marvell,armada-370-neta" },
> > + { .compatible = "marvell,armada-ac5-neta" },
> > { .compatible = "marvell,armada-xp-neta" },
> > { .compatible = "marvell,armada-3700-neta" },
> > { }
> > --
> > 2.37.3
> >
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v2 5/6] arm: mvebu: Support for 98DX25xx/98DX35xx SoC
2022-09-20 9:22 ` Pali Rohár
@ 2022-09-21 3:54 ` Chris Packham
2022-09-21 22:08 ` Pali Rohár
0 siblings, 1 reply; 17+ messages in thread
From: Chris Packham @ 2022-09-21 3:54 UTC (permalink / raw)
To: Pali Rohár
Cc: Stefan Roese, Elad Nachman, Vadym Kochan, Marek Behún,
Tom Rini, u-boot
On Tue, Sep 20, 2022 at 9:22 PM Pali Rohár <pali@kernel.org> wrote:
>
> On Tuesday 20 September 2022 20:31:52 Chris Packham wrote:
> > Add support for the Allecat5/Alleycat5X SoC. These are L3 switches with
> > an integrated CPU (referred to as the CnM block in Marvell's
> > documentation). These have dual ARMv8.2 CPUs (Cortex-A55). This support
> > has been ported from Marvell's SDK which is based on a much older
> > version of U-Boot.
> >
> > Signed-off-by: Chris Packham <judge.packham@gmail.com>
> > ---
> >
> > (no changes since v1)
> >
> > arch/arm/dts/ac5-98dx25xx.dtsi | 292 +++++++++++++++++++++++
> > arch/arm/dts/ac5-98dx35xx.dtsi | 17 ++
> > arch/arm/mach-mvebu/Kconfig | 5 +
> > arch/arm/mach-mvebu/Makefile | 1 +
> > arch/arm/mach-mvebu/alleycat5/Makefile | 9 +
> > arch/arm/mach-mvebu/alleycat5/clock.c | 49 ++++
> > arch/arm/mach-mvebu/alleycat5/cpu.c | 129 ++++++++++
> > arch/arm/mach-mvebu/alleycat5/soc.c | 229 ++++++++++++++++++
> > arch/arm/mach-mvebu/arm64-common.c | 15 ++
> > arch/arm/mach-mvebu/include/mach/clock.h | 11 +
> > arch/arm/mach-mvebu/include/mach/cpu.h | 4 +
> > arch/arm/mach-mvebu/include/mach/soc.h | 4 +
> > 12 files changed, 765 insertions(+)
> > create mode 100644 arch/arm/dts/ac5-98dx25xx.dtsi
> > create mode 100644 arch/arm/dts/ac5-98dx35xx.dtsi
> > create mode 100644 arch/arm/mach-mvebu/alleycat5/Makefile
> > create mode 100644 arch/arm/mach-mvebu/alleycat5/clock.c
> > create mode 100644 arch/arm/mach-mvebu/alleycat5/cpu.c
> > create mode 100644 arch/arm/mach-mvebu/alleycat5/soc.c
> > create mode 100644 arch/arm/mach-mvebu/include/mach/clock.h
> >
> ...
> > diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
> > index a81b8e2b0d..400a308985 100644
> > --- a/arch/arm/mach-mvebu/Kconfig
> > +++ b/arch/arm/mach-mvebu/Kconfig
> > @@ -49,6 +49,11 @@ config ARMADA_8K
> > bool
> > select ARM64
> >
> > +config ALLEYCAT_5
> > + bool
> > + select ARM64
> > + select HAVE_MVEBU_EFUSE
>
> Hello! You are not adding any efuse implementation for AC5 platform,
> so selecting this symbol seems to be wrong.
>
> Or are you reusing A3720 or A38x OTP implementation for AC5? This is not
> clear from the patch.
>
The original code did have some EFUSE stuff in it but I've dropped
most of it out. I think this can go.
> > +
> > # Armada PLL frequency (used for NAND clock generation)
> > config SYS_MVEBU_PLL_CLOCK
> > int
> ...
> > diff --git a/arch/arm/mach-mvebu/arm64-common.c b/arch/arm/mach-mvebu/arm64-common.c
> > index 238edbe6ba..c9b6f16c63 100644
> > --- a/arch/arm/mach-mvebu/arm64-common.c
> > +++ b/arch/arm/mach-mvebu/arm64-common.c
> > @@ -53,6 +53,8 @@ __weak int dram_init_banksize(void)
> > return a8k_dram_init_banksize();
> > else if (CONFIG_IS_ENABLED(ARMADA_3700))
> > return a3700_dram_init_banksize();
> > + else if (CONFIG_IS_ENABLED(ALLEYCAT_5))
> > + return alleycat5_dram_init_banksize();
> > else
> > return fdtdec_setup_memory_banksize();
> > }
> > @@ -68,6 +70,9 @@ __weak int dram_init(void)
> > if (CONFIG_IS_ENABLED(ARMADA_3700))
> > return a3700_dram_init();
> >
> > + if (CONFIG_IS_ENABLED(ALLEYCAT_5))
> > + return alleycat5_dram_init();
> > +
> > if (fdtdec_setup_mem_size_base() != 0)
> > return -EINVAL;
> >
> > @@ -100,6 +105,16 @@ int arch_early_init_r(void)
> > break;
> > }
> >
> > + i = 0;
> > + while (1) {
> > + /* Call the pinctrl code via the PINCTRL uclass driver */
> > + ret = uclass_get_device(UCLASS_PINCTRL, i++, &dev);
> > +
> > + /* We're done, once no further CP110 device is found */
> > + if (ret)
> > + break;
> > + }
>
> This code is unconditionally called for all 64-bit mvebu platforms, not
> only for new AC5. So if this is some fix, it should be in separate
> commit. If not then it should be marked AC5 specific and explained why.
>
Yeah I can't see why it's needed. The pinctrl device still gets probed
without it so I suspect it's just old cruft left over from a time that
wasn't the case.
> > +
> > /* Cause the SATA device to do its early init */
> > uclass_first_device(UCLASS_AHCI, &dev);
> >
> > diff --git a/arch/arm/mach-mvebu/include/mach/clock.h b/arch/arm/mach-mvebu/include/mach/clock.h
> > new file mode 100644
> > index 0000000000..93d965ad5a
> > --- /dev/null
> > +++ b/arch/arm/mach-mvebu/include/mach/clock.h
> > @@ -0,0 +1,11 @@
> > +/* SPDX-License-Identifier: GPL-2.0+ */
> > +/*
> > + * Copyright (C) 2018 Marvell International Ltd.
> > + */
> > +
> > +#ifndef _MVEBU_CLOCK_H_
> > +#define _MVEBU_CLOCK_H_
> > +
> > +void soc_print_clock_info(void);
>
> I'm not sure if this function needs to be exported. You are using it
> only in AC5 cpu.c file, in function print_cpuinfo(). So probably you can
> move soc_print_clock_info() into that file and then global mvebu clock.h
> would not be needed at all.
>
I'd need to fold all of the stuff in alleycat5/clock.c into
alleycat5/cpu.c but it should be doable. Alternatively I could keep it
separate but have a local .h file for this (and soc.h) to avoid
polluting the mvebu generic files.
> > +
> > +#endif /* _MVEBU_CLOCK_H_ */
> > diff --git a/arch/arm/mach-mvebu/include/mach/cpu.h b/arch/arm/mach-mvebu/include/mach/cpu.h
> > index b127fce865..c17c2440f1 100644
> > --- a/arch/arm/mach-mvebu/include/mach/cpu.h
> > +++ b/arch/arm/mach-mvebu/include/mach/cpu.h
> > @@ -174,6 +174,10 @@ int a3700_dram_init_banksize(void);
> > /* A3700 PCIe regions fixer for device tree */
> > int a3700_fdt_fix_pcie_regions(void *blob);
> >
> > +/* Alleycat5 dram functions */
> > +int alleycat5_dram_init(void);
> > +int alleycat5_dram_init_banksize(void);
> > +
> > /*
> > * get_ref_clk
> > *
> > diff --git a/arch/arm/mach-mvebu/include/mach/soc.h b/arch/arm/mach-mvebu/include/mach/soc.h
> > index 3b9618852c..b9312e37dc 100644
> > --- a/arch/arm/mach-mvebu/include/mach/soc.h
> > +++ b/arch/arm/mach-mvebu/include/mach/soc.h
> > @@ -212,4 +212,8 @@
> > #define CONFIG_SYS_TCLK 250000000 /* 250MHz */
> > #endif
> >
> > +#ifndef __ASSEMBLY__
> > +void soc_print_device_info(void);
> > +int soc_early_init_f(void);
>
> These two functions are not available on existing mvebu platforms,
> so I think functions should not be declared in global mvebu soc.h file.
>
This one is a bit weird. There is a weak version defined in the
board.c (same for the octeontx2_cn913x, possibly copied from similar
vendor code). But the actual implementation that we need is in
arch/arm/mach-mvebu/alleycat5/soc.c so my attempt to put a definition
in soc.h was to make this less mysterious but I forgot to remove the
weak definition.
The strong implementation is the thing that triggers the init for the
mvebu_sar driver from the previous patch. So I think I need to unpick
the SAR driver and figure out how to do it "properly" (addressing the
issues you've pointed out). What I intend to do is send a v3 series
without addressing this specific concern and then try and figure out
how much (or how little) of the SAR code I really need.
> > +#endif /* __ASSEMBLY__ */
> > #endif /* _MVEBU_SOC_H */
> > --
> > 2.37.3
> >
^ permalink raw reply [flat|nested] 17+ messages in thread
* Re: [PATCH v2 5/6] arm: mvebu: Support for 98DX25xx/98DX35xx SoC
2022-09-21 3:54 ` Chris Packham
@ 2022-09-21 22:08 ` Pali Rohár
0 siblings, 0 replies; 17+ messages in thread
From: Pali Rohár @ 2022-09-21 22:08 UTC (permalink / raw)
To: Chris Packham
Cc: Stefan Roese, Elad Nachman, Vadym Kochan, Marek Behún,
Tom Rini, u-boot
On Wednesday 21 September 2022 15:54:52 Chris Packham wrote:
> On Tue, Sep 20, 2022 at 9:22 PM Pali Rohár <pali@kernel.org> wrote:
> >
> > On Tuesday 20 September 2022 20:31:52 Chris Packham wrote:
> > > Add support for the Allecat5/Alleycat5X SoC. These are L3 switches with
> > > an integrated CPU (referred to as the CnM block in Marvell's
> > > documentation). These have dual ARMv8.2 CPUs (Cortex-A55). This support
> > > has been ported from Marvell's SDK which is based on a much older
> > > version of U-Boot.
> > >
> > > Signed-off-by: Chris Packham <judge.packham@gmail.com>
> > > ---
> > >
> > > (no changes since v1)
> > >
> > > arch/arm/dts/ac5-98dx25xx.dtsi | 292 +++++++++++++++++++++++
> > > arch/arm/dts/ac5-98dx35xx.dtsi | 17 ++
> > > arch/arm/mach-mvebu/Kconfig | 5 +
> > > arch/arm/mach-mvebu/Makefile | 1 +
> > > arch/arm/mach-mvebu/alleycat5/Makefile | 9 +
> > > arch/arm/mach-mvebu/alleycat5/clock.c | 49 ++++
> > > arch/arm/mach-mvebu/alleycat5/cpu.c | 129 ++++++++++
> > > arch/arm/mach-mvebu/alleycat5/soc.c | 229 ++++++++++++++++++
> > > arch/arm/mach-mvebu/arm64-common.c | 15 ++
> > > arch/arm/mach-mvebu/include/mach/clock.h | 11 +
> > > arch/arm/mach-mvebu/include/mach/cpu.h | 4 +
> > > arch/arm/mach-mvebu/include/mach/soc.h | 4 +
> > > 12 files changed, 765 insertions(+)
> > > create mode 100644 arch/arm/dts/ac5-98dx25xx.dtsi
> > > create mode 100644 arch/arm/dts/ac5-98dx35xx.dtsi
> > > create mode 100644 arch/arm/mach-mvebu/alleycat5/Makefile
> > > create mode 100644 arch/arm/mach-mvebu/alleycat5/clock.c
> > > create mode 100644 arch/arm/mach-mvebu/alleycat5/cpu.c
> > > create mode 100644 arch/arm/mach-mvebu/alleycat5/soc.c
> > > create mode 100644 arch/arm/mach-mvebu/include/mach/clock.h
> > >
> > ...
> > > diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
> > > index a81b8e2b0d..400a308985 100644
> > > --- a/arch/arm/mach-mvebu/Kconfig
> > > +++ b/arch/arm/mach-mvebu/Kconfig
> > > @@ -49,6 +49,11 @@ config ARMADA_8K
> > > bool
> > > select ARM64
> > >
> > > +config ALLEYCAT_5
> > > + bool
> > > + select ARM64
> > > + select HAVE_MVEBU_EFUSE
> >
> > Hello! You are not adding any efuse implementation for AC5 platform,
> > so selecting this symbol seems to be wrong.
> >
> > Or are you reusing A3720 or A38x OTP implementation for AC5? This is not
> > clear from the patch.
> >
>
> The original code did have some EFUSE stuff in it but I've dropped
> most of it out. I think this can go.
Ok! I know that there is Marvell **e**fuse API and U-Boot fuse API
(without leading e). For A3720 Marvell U-Boot has only **e**fuse
command and I have already ported it to U-Boot fuse and it is in
mainline.
So I think that same is for AC5 and if you need it, you would have to
port it to u-boot fuse API.
> > > +
> > > # Armada PLL frequency (used for NAND clock generation)
> > > config SYS_MVEBU_PLL_CLOCK
> > > int
> > ...
> > > diff --git a/arch/arm/mach-mvebu/arm64-common.c b/arch/arm/mach-mvebu/arm64-common.c
> > > index 238edbe6ba..c9b6f16c63 100644
> > > --- a/arch/arm/mach-mvebu/arm64-common.c
> > > +++ b/arch/arm/mach-mvebu/arm64-common.c
> > > @@ -53,6 +53,8 @@ __weak int dram_init_banksize(void)
> > > return a8k_dram_init_banksize();
> > > else if (CONFIG_IS_ENABLED(ARMADA_3700))
> > > return a3700_dram_init_banksize();
> > > + else if (CONFIG_IS_ENABLED(ALLEYCAT_5))
> > > + return alleycat5_dram_init_banksize();
> > > else
> > > return fdtdec_setup_memory_banksize();
> > > }
> > > @@ -68,6 +70,9 @@ __weak int dram_init(void)
> > > if (CONFIG_IS_ENABLED(ARMADA_3700))
> > > return a3700_dram_init();
> > >
> > > + if (CONFIG_IS_ENABLED(ALLEYCAT_5))
> > > + return alleycat5_dram_init();
> > > +
> > > if (fdtdec_setup_mem_size_base() != 0)
> > > return -EINVAL;
> > >
> > > @@ -100,6 +105,16 @@ int arch_early_init_r(void)
> > > break;
> > > }
> > >
> > > + i = 0;
> > > + while (1) {
> > > + /* Call the pinctrl code via the PINCTRL uclass driver */
> > > + ret = uclass_get_device(UCLASS_PINCTRL, i++, &dev);
> > > +
> > > + /* We're done, once no further CP110 device is found */
> > > + if (ret)
> > > + break;
> > > + }
> >
> > This code is unconditionally called for all 64-bit mvebu platforms, not
> > only for new AC5. So if this is some fix, it should be in separate
> > commit. If not then it should be marked AC5 specific and explained why.
> >
>
> Yeah I can't see why it's needed. The pinctrl device still gets probed
> without it so I suspect it's just old cruft left over from a time that
> wasn't the case.
Maybe because of this fix?
https://lore.kernel.org/u-boot/20220506180140.141049-1-robert.marko@sartura.hr/
> > > +
> > > /* Cause the SATA device to do its early init */
> > > uclass_first_device(UCLASS_AHCI, &dev);
> > >
> > > diff --git a/arch/arm/mach-mvebu/include/mach/clock.h b/arch/arm/mach-mvebu/include/mach/clock.h
> > > new file mode 100644
> > > index 0000000000..93d965ad5a
> > > --- /dev/null
> > > +++ b/arch/arm/mach-mvebu/include/mach/clock.h
> > > @@ -0,0 +1,11 @@
> > > +/* SPDX-License-Identifier: GPL-2.0+ */
> > > +/*
> > > + * Copyright (C) 2018 Marvell International Ltd.
> > > + */
> > > +
> > > +#ifndef _MVEBU_CLOCK_H_
> > > +#define _MVEBU_CLOCK_H_
> > > +
> > > +void soc_print_clock_info(void);
> >
> > I'm not sure if this function needs to be exported. You are using it
> > only in AC5 cpu.c file, in function print_cpuinfo(). So probably you can
> > move soc_print_clock_info() into that file and then global mvebu clock.h
> > would not be needed at all.
> >
>
> I'd need to fold all of the stuff in alleycat5/clock.c into
> alleycat5/cpu.c but it should be doable. Alternatively I could keep it
> separate but have a local .h file for this (and soc.h) to avoid
> polluting the mvebu generic files.
>
> > > +
> > > +#endif /* _MVEBU_CLOCK_H_ */
> > > diff --git a/arch/arm/mach-mvebu/include/mach/cpu.h b/arch/arm/mach-mvebu/include/mach/cpu.h
> > > index b127fce865..c17c2440f1 100644
> > > --- a/arch/arm/mach-mvebu/include/mach/cpu.h
> > > +++ b/arch/arm/mach-mvebu/include/mach/cpu.h
> > > @@ -174,6 +174,10 @@ int a3700_dram_init_banksize(void);
> > > /* A3700 PCIe regions fixer for device tree */
> > > int a3700_fdt_fix_pcie_regions(void *blob);
> > >
> > > +/* Alleycat5 dram functions */
> > > +int alleycat5_dram_init(void);
> > > +int alleycat5_dram_init_banksize(void);
> > > +
> > > /*
> > > * get_ref_clk
> > > *
> > > diff --git a/arch/arm/mach-mvebu/include/mach/soc.h b/arch/arm/mach-mvebu/include/mach/soc.h
> > > index 3b9618852c..b9312e37dc 100644
> > > --- a/arch/arm/mach-mvebu/include/mach/soc.h
> > > +++ b/arch/arm/mach-mvebu/include/mach/soc.h
> > > @@ -212,4 +212,8 @@
> > > #define CONFIG_SYS_TCLK 250000000 /* 250MHz */
> > > #endif
> > >
> > > +#ifndef __ASSEMBLY__
> > > +void soc_print_device_info(void);
> > > +int soc_early_init_f(void);
> >
> > These two functions are not available on existing mvebu platforms,
> > so I think functions should not be declared in global mvebu soc.h file.
> >
>
> This one is a bit weird. There is a weak version defined in the
> board.c (same for the octeontx2_cn913x, possibly copied from similar
> vendor code). But the actual implementation that we need is in
> arch/arm/mach-mvebu/alleycat5/soc.c so my attempt to put a definition
> in soc.h was to make this less mysterious but I forgot to remove the
> weak definition.
Yea, A70x0/A80x0/CN913x U-Boot code is not cleaned yet, contains lot of
unsystematic parts and its DTS is not compatible with Linux... So I'm
not surprised and even you already wrote that original code is based on
older u-boot version.
> The strong implementation is the thing that triggers the init for the
> mvebu_sar driver from the previous patch. So I think I need to unpick
> the SAR driver and figure out how to do it "properly" (addressing the
> issues you've pointed out). What I intend to do is send a v3 series
> without addressing this specific concern and then try and figure out
> how much (or how little) of the SAR code I really need.
>
> > > +#endif /* __ASSEMBLY__ */
> > > #endif /* _MVEBU_SOC_H */
> > > --
> > > 2.37.3
> > >
^ permalink raw reply [flat|nested] 17+ messages in thread
end of thread, other threads:[~2022-09-21 22:09 UTC | newest]
Thread overview: 17+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-09-20 8:31 [PATCH v2 0/6] arm: mvebu: Support for 98DX25xx/98DX35xx (AlleyCat5) Chris Packham
2022-09-20 8:31 ` [PATCH v2 1/6] net: mvneta: Add support for AlleyCat5 Chris Packham
2022-09-20 9:17 ` Stefan Roese
2022-09-21 1:04 ` Chris Packham
2022-09-20 10:48 ` Pali Rohár
2022-09-21 1:10 ` Chris Packham
2022-09-20 8:31 ` [PATCH v2 2/6] usb: ehci: ehci-marvell: Support for marvell,ac5-ehci Chris Packham
2022-09-20 9:08 ` Pali Rohár
2022-09-20 8:31 ` [PATCH v2 3/6] pinctrl: mvebu: Add AlleyCat5 support Chris Packham
2022-09-20 8:31 ` [PATCH v2 4/6] misc: mvebu: Add sample at reset driver Chris Packham
2022-09-20 10:42 ` Pali Rohár
2022-09-20 8:31 ` [PATCH v2 5/6] arm: mvebu: Support for 98DX25xx/98DX35xx SoC Chris Packham
2022-09-20 9:22 ` Pali Rohár
2022-09-21 3:54 ` Chris Packham
2022-09-21 22:08 ` Pali Rohár
2022-09-20 8:31 ` [PATCH v2 6/6] arm: mvebu: Add RD-AC5X board Chris Packham
2022-09-20 11:10 ` Pali Rohár
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).