All of lore.kernel.org
 help / color / mirror / Atom feed
From: Marek Vasut <marex@denx.de>
To: dri-devel@lists.freedesktop.org
Cc: Marek Vasut <marex@denx.de>,
	Thomas Zimmermann <tzimmermann@suse.de>,
	Sam Ravnborg <sam@ravnborg.org>,
	Jagan Teki <jagan@amarulasolutions.com>,
	Robert Foss <robert.foss@linaro.org>
Subject: [PATCH 12/14] drm: bridge: icn6211: Add I2C configuration support
Date: Fri, 14 Jan 2022 04:48:36 +0100	[thread overview]
Message-ID: <20220114034838.546267-12-marex@denx.de> (raw)
In-Reply-To: <20220114034838.546267-1-marex@denx.de>

The ICN6211 chip starts in I2C configuration mode after cold boot.
Implement support for configuring the chip via I2C in addition to
the current DSI LP command mode configuration support. The later
seems to be available only on chips which have additional MCU on
the panel/bridge board which preconfigures the ICN6211, while the
I2C configuration mode added by this patch does not require any
such MCU.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
---
 drivers/gpu/drm/bridge/chipone-icn6211.c | 219 +++++++++++++++++++----
 1 file changed, 188 insertions(+), 31 deletions(-)

diff --git a/drivers/gpu/drm/bridge/chipone-icn6211.c b/drivers/gpu/drm/bridge/chipone-icn6211.c
index 8226fefeedfc9..313c588297eca 100644
--- a/drivers/gpu/drm/bridge/chipone-icn6211.c
+++ b/drivers/gpu/drm/bridge/chipone-icn6211.c
@@ -11,6 +11,7 @@
 
 #include <linux/delay.h>
 #include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/regulator/consumer.h>
@@ -133,14 +134,17 @@
 
 struct chipone {
 	struct device *dev;
+	struct i2c_client *client;
 	struct drm_bridge bridge;
 	struct drm_bridge *panel_bridge;
 	struct device_node *host_node;
+	struct mipi_dsi_device *dsi;
 	struct gpio_desc *enable_gpio;
 	struct regulator *vdd1;
 	struct regulator *vdd2;
 	struct regulator *vdd3;
 	int dsi_lanes;
+	bool interface_i2c;
 };
 
 static inline struct chipone *bridge_to_chipone(struct drm_bridge *bridge)
@@ -172,20 +176,14 @@ bridge_to_mode(struct drm_bridge *bridge, struct drm_atomic_state *state)
 	return &crtc_state->adjusted_mode;
 }
 
-static inline int chipone_dsi_write(struct chipone *icn,  const void *seq,
-				    size_t len)
+static void ICN6211_DSI(struct chipone *icn, u8 reg, u8 val)
 {
-	struct mipi_dsi_device *dsi = to_mipi_dsi_device(icn->dev);
-
-	return mipi_dsi_generic_write(dsi, seq, len);
+	if (icn->interface_i2c)
+		i2c_smbus_write_byte_data(icn->client, reg, val);
+	else
+		mipi_dsi_generic_write(icn->dsi, (u8[]){reg, val}, 2);
 }
 
-#define ICN6211_DSI(icn, seq...)				\
-	{							\
-		const u8 d[] = { seq };				\
-		chipone_dsi_write(icn, d, ARRAY_SIZE(d));	\
-	}
-
 static void chipone_configure_pll(struct chipone *icn,
 				  const struct drm_display_mode *mode)
 {
@@ -282,7 +280,10 @@ static void chipone_atomic_enable(struct drm_bridge *bridge,
 	bridge_state = drm_atomic_get_new_bridge_state(state, bridge);
 	bus_flags = bridge_state->output_bus_cfg.flags;
 
-	ICN6211_DSI(icn, MIPI_CFG_PW, MIPI_CFG_PW_CONFIG_DSI);
+	if (icn->interface_i2c)
+		ICN6211_DSI(icn, MIPI_CFG_PW, MIPI_CFG_PW_CONFIG_I2C);
+	else
+		ICN6211_DSI(icn, MIPI_CFG_PW, MIPI_CFG_PW_CONFIG_DSI);
 
 	ICN6211_DSI(icn, HACTIVE_LI, mode->hdisplay & 0xff);
 
@@ -396,11 +397,86 @@ static void chipone_atomic_post_disable(struct drm_bridge *bridge,
 	gpiod_set_value(icn->enable_gpio, 0);
 }
 
+static int chipone_dsi_attach(struct chipone *icn)
+{
+	struct mipi_dsi_device *dsi = icn->dsi;
+	int ret;
+
+	dsi->lanes = icn->dsi_lanes;
+	dsi->format = MIPI_DSI_FMT_RGB888;
+	dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
+			  MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET;
+
+	ret = mipi_dsi_attach(dsi);
+	if (ret < 0)
+		dev_err(icn->dev, "failed to attach dsi\n");
+
+	return ret;
+}
+
+static int chipone_dsi_setup(struct chipone *icn)
+{
+	struct device *dev = icn->dev;
+	struct mipi_dsi_device *dsi;
+	struct mipi_dsi_host *host;
+	int ret = 0;
+
+	const struct mipi_dsi_device_info info = {
+		.type = "chipone",
+		.channel = 0,
+		.node = NULL,
+	};
+
+	host = of_find_mipi_dsi_host_by_node(icn->host_node);
+	if (!host) {
+		dev_err(dev, "failed to find dsi host\n");
+		return -EPROBE_DEFER;
+	}
+
+	dsi = mipi_dsi_device_register_full(host, &info);
+	if (IS_ERR(dsi)) {
+		return dev_err_probe(dev, PTR_ERR(dsi),
+				     "failed to create dsi device\n");
+	}
+
+	icn->dsi = dsi;
+
+	ret = chipone_dsi_attach(icn);
+	if (ret < 0)
+		mipi_dsi_device_unregister(dsi);
+
+	return ret;
+}
+
 static int chipone_attach(struct drm_bridge *bridge, enum drm_bridge_attach_flags flags)
 {
 	struct chipone *icn = bridge_to_chipone(bridge);
+	struct drm_bridge *abridge = bridge;
+	int ret;
+
+	if (icn->interface_i2c) {
+		ret = chipone_dsi_setup(icn);
+		if (ret)
+			return ret;
+
+		abridge = &icn->bridge;
+	}
+
+	return drm_bridge_attach(bridge->encoder, icn->panel_bridge,
+				 bridge, flags);
+}
+
+static void chipone_detach(struct drm_bridge *bridge)
+{
+	struct chipone *icn = bridge_to_chipone(bridge);
+
+	if (!icn->dsi || icn->interface_i2c)
+		return;
 
-	return drm_bridge_attach(bridge->encoder, icn->panel_bridge, bridge, flags);
+	mipi_dsi_detach(icn->dsi);
+	mipi_dsi_device_unregister(icn->dsi);
+	drm_bridge_remove(&icn->bridge);
+	icn->dsi = NULL;
 }
 
 #define MAX_INPUT_SEL_FORMATS	1
@@ -431,6 +507,7 @@ chipone_atomic_get_input_bus_fmts(struct drm_bridge *bridge,
 
 static const struct drm_bridge_funcs chipone_bridge_funcs = {
 	.attach = chipone_attach,
+	.detach = chipone_detach,
 	.atomic_post_disable = chipone_atomic_post_disable,
 	.atomic_pre_enable = chipone_atomic_pre_enable,
 	.atomic_enable = chipone_atomic_enable,
@@ -505,9 +582,8 @@ static int chipone_parse_dt(struct chipone *icn)
 	return 0;
 }
 
-static int chipone_probe(struct mipi_dsi_device *dsi)
+static int chipone_common_probe(struct device *dev, struct chipone **icnr)
 {
-	struct device *dev = &dsi->dev;
 	struct chipone *icn;
 	int ret;
 
@@ -515,7 +591,6 @@ static int chipone_probe(struct mipi_dsi_device *dsi)
 	if (!icn)
 		return -ENOMEM;
 
-	mipi_dsi_set_drvdata(dsi, icn);
 	icn->dev = dev;
 
 	ret = chipone_parse_dt(icn);
@@ -526,29 +601,77 @@ static int chipone_probe(struct mipi_dsi_device *dsi)
 	icn->bridge.type = DRM_MODE_CONNECTOR_DPI;
 	icn->bridge.of_node = dev->of_node;
 
-	drm_bridge_add(&icn->bridge);
+	*icnr = icn;
 
-	dsi->lanes = icn->dsi_lanes;
-	dsi->format = MIPI_DSI_FMT_RGB888;
-	dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST |
-			  MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_NO_EOT_PACKET;
+	return ret;
+}
 
-	ret = mipi_dsi_attach(dsi);
-	if (ret < 0) {
+static int chipone_dsi_probe(struct mipi_dsi_device *dsi)
+{
+	struct device *dev = &dsi->dev;
+	struct chipone *icn;
+	int ret;
+
+	ret = chipone_common_probe(dev, &icn);
+	if (ret)
+		return ret;
+
+	icn->interface_i2c = false;
+	icn->dsi = dsi;
+
+	mipi_dsi_set_drvdata(dsi, icn);
+
+	drm_bridge_add(&icn->bridge);
+
+	ret = chipone_dsi_attach(icn);
+	if (ret)
 		drm_bridge_remove(&icn->bridge);
-		dev_err(dev, "failed to attach dsi\n");
-	}
 
 	return ret;
 }
 
-static int chipone_remove(struct mipi_dsi_device *dsi)
+static int chipone_i2c_probe(struct i2c_client *client,
+			     const struct i2c_device_id *id)
+{
+	struct device *dev = &client->dev;
+	struct chipone *icn;
+	int ret;
+
+	ret = chipone_common_probe(dev, &icn);
+	if (ret)
+		return ret;
+
+	icn->interface_i2c = true;
+	icn->client = client;
+	dev_set_drvdata(dev, icn);
+	i2c_set_clientdata(client, icn);
+
+	drm_bridge_add(&icn->bridge);
+
+	return ret;
+}
+
+static void chipone_common_remove(struct chipone *icn)
+{
+	of_node_put(icn->host_node);
+}
+
+static int chipone_dsi_remove(struct mipi_dsi_device *dsi)
 {
 	struct chipone *icn = mipi_dsi_get_drvdata(dsi);
 
 	mipi_dsi_detach(dsi);
 	drm_bridge_remove(&icn->bridge);
-	of_node_put(icn->host_node);
+	chipone_common_remove(icn);
+
+	return 0;
+}
+
+static int chipone_i2c_remove(struct i2c_client *client)
+{
+	struct chipone *icn = i2c_get_clientdata(client);
+
+	chipone_common_remove(icn);
 
 	return 0;
 }
@@ -559,16 +682,50 @@ static const struct of_device_id chipone_of_match[] = {
 };
 MODULE_DEVICE_TABLE(of, chipone_of_match);
 
-static struct mipi_dsi_driver chipone_driver = {
-	.probe = chipone_probe,
-	.remove = chipone_remove,
+static struct mipi_dsi_driver chipone_dsi_driver = {
+	.probe = chipone_dsi_probe,
+	.remove = chipone_dsi_remove,
 	.driver = {
 		.name = "chipone-icn6211",
 		.owner = THIS_MODULE,
 		.of_match_table = chipone_of_match,
 	},
 };
-module_mipi_dsi_driver(chipone_driver);
+
+static struct i2c_device_id chipone_i2c_id[] = {
+	{ "chipone,icn6211" },
+	{},
+};
+MODULE_DEVICE_TABLE(i2c, chipone_i2c_id);
+
+static struct i2c_driver chipone_i2c_driver = {
+	.probe = chipone_i2c_probe,
+	.remove = chipone_i2c_remove,
+	.id_table = chipone_i2c_id,
+	.driver = {
+		.name = "chipone-icn6211-i2c",
+		.owner = THIS_MODULE,
+		.of_match_table = chipone_of_match,
+	},
+};
+
+static int __init chipone_init(void)
+{
+	if (IS_ENABLED(CONFIG_DRM_MIPI_DSI))
+		mipi_dsi_driver_register(&chipone_dsi_driver);
+
+	return i2c_add_driver(&chipone_i2c_driver);
+}
+module_init(chipone_init);
+
+static void __init chipone_exit(void)
+{
+	i2c_del_driver(&chipone_i2c_driver);
+
+	if (IS_ENABLED(CONFIG_DRM_MIPI_DSI))
+		mipi_dsi_driver_unregister(&chipone_dsi_driver);
+}
+module_exit(chipone_exit);
 
 MODULE_AUTHOR("Jagan Teki <jagan@amarulasolutions.com>");
 MODULE_DESCRIPTION("Chipone ICN6211 MIPI-DSI to RGB Converter Bridge");
-- 
2.34.1


  parent reply	other threads:[~2022-01-14  3:49 UTC|newest]

Thread overview: 23+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-01-14  3:48 [PATCH 01/14] drm: bridge: icn6211: Fix register layout Marek Vasut
2022-01-14  3:48 ` [PATCH 02/14] drm: bridge: icn6211: Fix HFP_HSW_HBP_HI and HFP_MIN handling Marek Vasut
2022-01-14  3:48 ` [PATCH 03/14] drm: bridge: icn6211: Switch to atomic operations Marek Vasut
2022-01-14  3:48 ` [PATCH 04/14] drm: bridge: icn6211: Implement atomic_get_input_bus_fmts Marek Vasut
2022-01-14  3:48 ` [PATCH 05/14] drm: bridge: icn6211: Retrieve the display mode from the state Marek Vasut
2022-02-03 12:09   ` Maxime Ripard
2022-02-16 20:13     ` Marek Vasut
2022-01-14  3:48 ` [PATCH 06/14] drm: bridge: icn6211: Add HS/VS/DE polarity handling Marek Vasut
2022-01-14  3:48 ` [PATCH 07/14] drm: bridge: icn6211: Add DSI lane count DT property parsing Marek Vasut
2022-02-03 12:13   ` Maxime Ripard
2022-02-16 20:24     ` Marek Vasut
2022-01-14  3:48 ` [PATCH 08/14] drm: bridge: icn6211: Add generic DSI-to-DPI PLL configuration Marek Vasut
2022-01-14  3:48 ` [PATCH 09/14] drm: bridge: icn6211: Use DSI burst mode without EoT and with LP command mode Marek Vasut
2022-01-14  3:48 ` [PATCH 10/14] drm: bridge: icn6211: Disable DPI color swap Marek Vasut
2022-01-14  3:48 ` [PATCH 11/14] drm: bridge: icn6211: Set SYS_CTRL_1 to value used in examples Marek Vasut
2022-01-14  3:48 ` Marek Vasut [this message]
2022-01-14 10:24   ` [PATCH 12/14] drm: bridge: icn6211: Add I2C configuration support kernel test robot
2022-01-14 10:24     ` kernel test robot
2022-02-03 12:17   ` Maxime Ripard
2022-01-14  3:48 ` [PATCH 13/14] drm: bridge: icn6211: Rename ICN6211_DSI to chipone_writeb Marek Vasut
2022-01-14  3:48 ` [PATCH 14/14] drm: bridge: icn6211: Read and validate chip IDs before configuration Marek Vasut
2022-01-14  8:16 ` [PATCH 01/14] drm: bridge: icn6211: Fix register layout Jagan Teki
2022-01-14 14:33   ` Marek Vasut

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20220114034838.546267-12-marex@denx.de \
    --to=marex@denx.de \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=jagan@amarulasolutions.com \
    --cc=robert.foss@linaro.org \
    --cc=sam@ravnborg.org \
    --cc=tzimmermann@suse.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.