From: Michal Simek <michal.simek@xilinx.com> To: linux-kernel@vger.kernel.org, monstr@monstr.eu, michal.simek@xilinx.com, git@xilinx.com Cc: Piyush Mehta <piyush.mehta@xilinx.com>, Al Cooper <alcooperx@gmail.com>, Alan Stern <stern@rowland.harvard.edu>, "Alexander A. Klimov" <grandmaster@al2klimov.de>, Bastien Nocera <hadess@hadess.net>, Greg Kroah-Hartman <gregkh@linuxfoundation.org>, Masahiro Yamada <masahiroy@kernel.org>, linux-arm-kernel@lists.infradead.org, linux-usb@vger.kernel.org Subject: [PATCH v2 2/2] usb: misc: usb5744: Add support for USB hub controller Date: Tue, 9 Feb 2021 11:48:10 +0100 [thread overview] Message-ID: <d6accf76bb5d060a13067816f23008e93264f317.1612867682.git.michal.simek@xilinx.com> (raw) In-Reply-To: <cover.1612867682.git.michal.simek@xilinx.com> From: Piyush Mehta <piyush.mehta@xilinx.com> This patch adds a USB GPIO based hub reset for USB5744 hub. This usb5744 driver trigger hub reset signal after soft reset or core Reset. The HUB needs to be resetted after completion of phy initialization. After the toggling of gpio, hub configure using i2c usb attached command. USB5744 hub can be used without any I2C connection, is handled by a simple platform device driver. As part of the reset, sets the direction of the pin to output before toggling the pin. Delay of millisecond is added in between low and high to meet the setup and hold time requirement of the reset. Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> --- Changes in v2: - s/USB_USB5744/USB_HUB_USB5744/g - Fix order in Makefile and Kconfig MAINTAINERS | 1 + drivers/usb/misc/Kconfig | 9 +++ drivers/usb/misc/Makefile | 1 + drivers/usb/misc/usb5744.c | 115 +++++++++++++++++++++++++++++++++++++ 4 files changed, 126 insertions(+) create mode 100644 drivers/usb/misc/usb5744.c diff --git a/MAINTAINERS b/MAINTAINERS index 7439471b5d37..56d1fcdd24f6 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2706,6 +2706,7 @@ F: drivers/edac/synopsys_edac.c F: drivers/i2c/busses/i2c-cadence.c F: drivers/i2c/busses/i2c-xiic.c F: drivers/mmc/host/sdhci-of-arasan.c +F: drivers/usb/misc/usb5744.c N: zynq N: xilinx diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig index 8f1144359012..9995a5701fd9 100644 --- a/drivers/usb/misc/Kconfig +++ b/drivers/usb/misc/Kconfig @@ -255,6 +255,15 @@ config USB_HSIC_USB4604 help This option enables support for SMSC USB4604 HSIC to USB 2.0 Driver. +config USB_HUB_USB5744 + tristate "Microchip USB5744 Hub driver" + depends on I2C + depends on GPIOLIB + help + This option enables support for Microchip USB5744 Hub. This driver + optionally reset the hub using gpio pin and configure hub via i2c if + connected. + config USB_LINK_LAYER_TEST tristate "USB Link Layer Test driver" help diff --git a/drivers/usb/misc/Makefile b/drivers/usb/misc/Makefile index 5f4e598573ab..fbb9adf08f8c 100644 --- a/drivers/usb/misc/Makefile +++ b/drivers/usb/misc/Makefile @@ -27,6 +27,7 @@ obj-$(CONFIG_USB_YUREX) += yurex.o obj-$(CONFIG_USB_HUB_USB251XB) += usb251xb.o obj-$(CONFIG_USB_HSIC_USB3503) += usb3503.o obj-$(CONFIG_USB_HSIC_USB4604) += usb4604.o +obj-$(CONFIG_USB_HUB_USB5744) += usb5744.o obj-$(CONFIG_USB_CHAOSKEY) += chaoskey.o obj-$(CONFIG_USB_SISUSBVGA) += sisusbvga/ diff --git a/drivers/usb/misc/usb5744.c b/drivers/usb/misc/usb5744.c new file mode 100644 index 000000000000..729b76345c69 --- /dev/null +++ b/drivers/usb/misc/usb5744.c @@ -0,0 +1,115 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Driver for the Microchip USB5744 4-port hub. + * + * Copyright (c) 2021 Xilinx, Inc. + */ + +#include <linux/delay.h> +#include <linux/err.h> +#include <linux/i2c.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/gpio/consumer.h> +#include <linux/platform_device.h> + +static int usb5744_init_hw(struct device *dev) +{ + struct gpio_desc *reset_gpio; + + reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH); + if (IS_ERR(reset_gpio)) { + dev_err(dev, "Failed to bind reset gpio"); + return -ENODEV; + } + + if (reset_gpio) { + /* Toggle RESET_N to reset the hub. */ + gpiod_set_value(reset_gpio, 0); + usleep_range(5, 20); /* trstia */ + gpiod_set_value(reset_gpio, 1); + usleep_range(5000, 10000); /* tcsh */ + } + + return 0; +} + +static int usb5744_i2c_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct device *dev = &client->dev; + int ret; + + /* Trigger gpio reset to the hub. */ + ret = usb5744_init_hw(dev); + if (ret) + return ret; + + /* Send SMBus command to boot hub. */ + ret = i2c_smbus_write_word_data(client, 0xAA, swab16(0x5600)); + if (ret < 0) + dev_err(dev, "Sending boot command failed"); + + return ret; +} + +static int usb5744_platform_probe(struct platform_device *pdev) +{ + /* Trigger gpio reset to the hub. */ + return usb5744_init_hw(&pdev->dev); +} + +static const struct i2c_device_id usb5744_id[] = { + { "usb5744", 0 }, + {} +}; +MODULE_DEVICE_TABLE(i2c, usb5744_id); + +static struct i2c_driver usb5744_i2c_driver = { + .driver = { + .name = "usb5744", + }, + .probe = usb5744_i2c_probe, + .id_table = usb5744_id, +}; + +static const struct of_device_id usb5744_platform_id[] = { + { .compatible = "microchip,usb5744", }, + { } +}; + +static struct platform_driver usb5744_platform_driver = { + .driver = { + .name = "microchip,usb5744", + .of_match_table = usb5744_platform_id, + }, + .probe = usb5744_platform_probe, +}; + +static int __init usb5744_init(void) +{ + int err; + + err = i2c_add_driver(&usb5744_i2c_driver); + if (err != 0) + pr_err("usb5744: Failed to register I2C driver: %d\n", err); + + err = platform_driver_register(&usb5744_platform_driver); + if (err != 0) + pr_err("usb5744: Failed to register platform driver: %d\n", + err); + return 0; +} +module_init(usb5744_init); + +static void __exit usb5744_exit(void) +{ + platform_driver_unregister(&usb5744_platform_driver); + i2c_del_driver(&usb5744_i2c_driver); +} +module_exit(usb5744_exit); + +MODULE_AUTHOR("Piyush Mehta <piyush.mehta@xilinx.com>"); +MODULE_AUTHOR("Michal Simek <michal.simek@xilinx.com>"); +MODULE_DESCRIPTION("USB5744 Hub"); +MODULE_LICENSE("GPL v2"); -- 2.30.0
WARNING: multiple messages have this Message-ID (diff)
From: Michal Simek <michal.simek@xilinx.com> To: linux-kernel@vger.kernel.org, monstr@monstr.eu, michal.simek@xilinx.com, git@xilinx.com Cc: linux-usb@vger.kernel.org, "Alexander A. Klimov" <grandmaster@al2klimov.de>, Piyush Mehta <piyush.mehta@xilinx.com>, Masahiro Yamada <masahiroy@kernel.org>, Al Cooper <alcooperx@gmail.com>, Alan Stern <stern@rowland.harvard.edu>, Bastien Nocera <hadess@hadess.net>, Greg Kroah-Hartman <gregkh@linuxfoundation.org>, linux-arm-kernel@lists.infradead.org Subject: [PATCH v2 2/2] usb: misc: usb5744: Add support for USB hub controller Date: Tue, 9 Feb 2021 11:48:10 +0100 [thread overview] Message-ID: <d6accf76bb5d060a13067816f23008e93264f317.1612867682.git.michal.simek@xilinx.com> (raw) In-Reply-To: <cover.1612867682.git.michal.simek@xilinx.com> From: Piyush Mehta <piyush.mehta@xilinx.com> This patch adds a USB GPIO based hub reset for USB5744 hub. This usb5744 driver trigger hub reset signal after soft reset or core Reset. The HUB needs to be resetted after completion of phy initialization. After the toggling of gpio, hub configure using i2c usb attached command. USB5744 hub can be used without any I2C connection, is handled by a simple platform device driver. As part of the reset, sets the direction of the pin to output before toggling the pin. Delay of millisecond is added in between low and high to meet the setup and hold time requirement of the reset. Signed-off-by: Piyush Mehta <piyush.mehta@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> --- Changes in v2: - s/USB_USB5744/USB_HUB_USB5744/g - Fix order in Makefile and Kconfig MAINTAINERS | 1 + drivers/usb/misc/Kconfig | 9 +++ drivers/usb/misc/Makefile | 1 + drivers/usb/misc/usb5744.c | 115 +++++++++++++++++++++++++++++++++++++ 4 files changed, 126 insertions(+) create mode 100644 drivers/usb/misc/usb5744.c diff --git a/MAINTAINERS b/MAINTAINERS index 7439471b5d37..56d1fcdd24f6 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2706,6 +2706,7 @@ F: drivers/edac/synopsys_edac.c F: drivers/i2c/busses/i2c-cadence.c F: drivers/i2c/busses/i2c-xiic.c F: drivers/mmc/host/sdhci-of-arasan.c +F: drivers/usb/misc/usb5744.c N: zynq N: xilinx diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig index 8f1144359012..9995a5701fd9 100644 --- a/drivers/usb/misc/Kconfig +++ b/drivers/usb/misc/Kconfig @@ -255,6 +255,15 @@ config USB_HSIC_USB4604 help This option enables support for SMSC USB4604 HSIC to USB 2.0 Driver. +config USB_HUB_USB5744 + tristate "Microchip USB5744 Hub driver" + depends on I2C + depends on GPIOLIB + help + This option enables support for Microchip USB5744 Hub. This driver + optionally reset the hub using gpio pin and configure hub via i2c if + connected. + config USB_LINK_LAYER_TEST tristate "USB Link Layer Test driver" help diff --git a/drivers/usb/misc/Makefile b/drivers/usb/misc/Makefile index 5f4e598573ab..fbb9adf08f8c 100644 --- a/drivers/usb/misc/Makefile +++ b/drivers/usb/misc/Makefile @@ -27,6 +27,7 @@ obj-$(CONFIG_USB_YUREX) += yurex.o obj-$(CONFIG_USB_HUB_USB251XB) += usb251xb.o obj-$(CONFIG_USB_HSIC_USB3503) += usb3503.o obj-$(CONFIG_USB_HSIC_USB4604) += usb4604.o +obj-$(CONFIG_USB_HUB_USB5744) += usb5744.o obj-$(CONFIG_USB_CHAOSKEY) += chaoskey.o obj-$(CONFIG_USB_SISUSBVGA) += sisusbvga/ diff --git a/drivers/usb/misc/usb5744.c b/drivers/usb/misc/usb5744.c new file mode 100644 index 000000000000..729b76345c69 --- /dev/null +++ b/drivers/usb/misc/usb5744.c @@ -0,0 +1,115 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Driver for the Microchip USB5744 4-port hub. + * + * Copyright (c) 2021 Xilinx, Inc. + */ + +#include <linux/delay.h> +#include <linux/err.h> +#include <linux/i2c.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/gpio/consumer.h> +#include <linux/platform_device.h> + +static int usb5744_init_hw(struct device *dev) +{ + struct gpio_desc *reset_gpio; + + reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH); + if (IS_ERR(reset_gpio)) { + dev_err(dev, "Failed to bind reset gpio"); + return -ENODEV; + } + + if (reset_gpio) { + /* Toggle RESET_N to reset the hub. */ + gpiod_set_value(reset_gpio, 0); + usleep_range(5, 20); /* trstia */ + gpiod_set_value(reset_gpio, 1); + usleep_range(5000, 10000); /* tcsh */ + } + + return 0; +} + +static int usb5744_i2c_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + struct device *dev = &client->dev; + int ret; + + /* Trigger gpio reset to the hub. */ + ret = usb5744_init_hw(dev); + if (ret) + return ret; + + /* Send SMBus command to boot hub. */ + ret = i2c_smbus_write_word_data(client, 0xAA, swab16(0x5600)); + if (ret < 0) + dev_err(dev, "Sending boot command failed"); + + return ret; +} + +static int usb5744_platform_probe(struct platform_device *pdev) +{ + /* Trigger gpio reset to the hub. */ + return usb5744_init_hw(&pdev->dev); +} + +static const struct i2c_device_id usb5744_id[] = { + { "usb5744", 0 }, + {} +}; +MODULE_DEVICE_TABLE(i2c, usb5744_id); + +static struct i2c_driver usb5744_i2c_driver = { + .driver = { + .name = "usb5744", + }, + .probe = usb5744_i2c_probe, + .id_table = usb5744_id, +}; + +static const struct of_device_id usb5744_platform_id[] = { + { .compatible = "microchip,usb5744", }, + { } +}; + +static struct platform_driver usb5744_platform_driver = { + .driver = { + .name = "microchip,usb5744", + .of_match_table = usb5744_platform_id, + }, + .probe = usb5744_platform_probe, +}; + +static int __init usb5744_init(void) +{ + int err; + + err = i2c_add_driver(&usb5744_i2c_driver); + if (err != 0) + pr_err("usb5744: Failed to register I2C driver: %d\n", err); + + err = platform_driver_register(&usb5744_platform_driver); + if (err != 0) + pr_err("usb5744: Failed to register platform driver: %d\n", + err); + return 0; +} +module_init(usb5744_init); + +static void __exit usb5744_exit(void) +{ + platform_driver_unregister(&usb5744_platform_driver); + i2c_del_driver(&usb5744_i2c_driver); +} +module_exit(usb5744_exit); + +MODULE_AUTHOR("Piyush Mehta <piyush.mehta@xilinx.com>"); +MODULE_AUTHOR("Michal Simek <michal.simek@xilinx.com>"); +MODULE_DESCRIPTION("USB5744 Hub"); +MODULE_LICENSE("GPL v2"); -- 2.30.0 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-02-09 10:54 UTC|newest] Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top 2021-02-09 10:48 [PATCH v2 0/2] usb: misc: Add support for Microchip USB5744 Michal Simek 2021-02-09 10:48 ` Michal Simek 2021-02-09 10:48 ` [PATCH v2 1/2] dt-bindings: usb: misc: Add binding for Microchip usb5744 hub Michal Simek 2021-02-09 10:48 ` Michal Simek 2021-02-10 22:22 ` Rob Herring 2021-02-10 22:22 ` Rob Herring 2021-02-11 9:35 ` Michal Simek 2021-02-11 9:35 ` Michal Simek 2021-02-11 14:42 ` Rob Herring 2021-02-11 14:42 ` Rob Herring 2021-02-24 13:37 ` Michal Simek 2021-02-24 13:37 ` Michal Simek 2021-03-04 20:02 ` Rob Herring 2021-03-04 20:02 ` Rob Herring 2021-02-09 10:48 ` Michal Simek [this message] 2021-02-09 10:48 ` [PATCH v2 2/2] usb: misc: usb5744: Add support for USB hub controller Michal Simek 2021-02-09 11:20 ` Greg Kroah-Hartman 2021-02-09 11:20 ` Greg Kroah-Hartman
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=d6accf76bb5d060a13067816f23008e93264f317.1612867682.git.michal.simek@xilinx.com \ --to=michal.simek@xilinx.com \ --cc=alcooperx@gmail.com \ --cc=git@xilinx.com \ --cc=grandmaster@al2klimov.de \ --cc=gregkh@linuxfoundation.org \ --cc=hadess@hadess.net \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-usb@vger.kernel.org \ --cc=masahiroy@kernel.org \ --cc=monstr@monstr.eu \ --cc=piyush.mehta@xilinx.com \ --cc=stern@rowland.harvard.edu \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.