* [PATCH 1/2] ARM: dts: aspeed: romulus: Add gpio line names
@ 2020-03-06 17:02 Andrew Geissler
2020-03-06 17:02 ` [PATCH 2/2] ARM: dts: aspeed: zaius: " Andrew Geissler
0 siblings, 1 reply; 6+ messages in thread
From: Andrew Geissler @ 2020-03-06 17:02 UTC (permalink / raw)
To: joel, devicetree, linux-arm-kernel, linux-aspeed, linux-kernel
Cc: linux-gpio, openbmc, Andrew Geissler
Name the GPIOs to help userspace work with them. The names describe the
functionality the lines provide, not the net or ball name. This makes it
easier to share userspace code across different systems and makes the
use of the lines more obvious.
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
---
arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts | 35 ++++++++++++++++++--
1 file changed, 32 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts b/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts
index edfa44fe1f75..fd2e014dae75 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts
@@ -231,23 +231,52 @@
};
&gpio {
+ gpio-line-names =
+ /*A0-A7*/ "","cfam-reset","","","","","fsi-mux","",
+ /*B0-B7*/ "","","","","","","","",
+ /*C0-C7*/ "","","","","","","","",
+ /*D0-D7*/ "fsi-enable","","","nic_func_mode0","nic_func_mode1","","","",
+ /*E0-E7*/ "","","","","","","","",
+ /*F0-F7*/ "","","","","","","","",
+ /*G0-G7*/ "","","","","","","","",
+ /*H0-H7*/ "","","","","","","","",
+ /*I0-I7*/ "","","","power-button","","","","",
+ /*J0-J7*/ "","","checkstop","","","","","",
+ /*K0-K7*/ "","","","","","","","",
+ /*L0-L7*/ "","","","","","","","",
+ /*M0-M7*/ "","","","","","","","",
+ /*N0-N7*/ "","","led-fault","",
+ "led-identify","","","",
+ /*O0-O7*/ "","","","","","","","",
+ /*P0-P7*/ "","","","","","","","",
+ /*Q0-Q7*/ "","","","","","","","id-button",
+ /*R0-R7*/ "","","fsi-trans","","","led-power","","",
+ /*S0-S7*/ "","","","","","","","seq_cont",
+ /*T0-T7*/ "","","","","","","","",
+ /*U0-U7*/ "","","","","","","","",
+ /*V0-V7*/ "","","","","","","","",
+ /*W0-W7*/ "","","","","","","","",
+ /*X0-X7*/ "","","","","","","","",
+ /*Y0-Y7*/ "","","","","","","","",
+ /*Z0-Z7*/ "","","","","","","","",
+ /*AA0-AA7*/ "fsi-clock","","fsi-data","","","","","",
+ /*AB0-AB7*/ "","","","","","","","",
+ /*AC0-AC7*/ "","","","","","","","";
+
nic_func_mode0 {
gpio-hog;
gpios = <ASPEED_GPIO(D, 3) GPIO_ACTIVE_HIGH>;
output-low;
- line-name = "nic_func_mode0";
};
nic_func_mode1 {
gpio-hog;
gpios = <ASPEED_GPIO(D, 4) GPIO_ACTIVE_HIGH>;
output-low;
- line-name = "nic_func_mode1";
};
seq_cont {
gpio-hog;
gpios = <ASPEED_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
output-low;
- line-name = "seq_cont";
};
};
--
2.21.0 (Apple Git-122)
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 2/2] ARM: dts: aspeed: zaius: Add gpio line names
2020-03-06 17:02 [PATCH 1/2] ARM: dts: aspeed: romulus: Add gpio line names Andrew Geissler
@ 2020-03-06 17:02 ` Andrew Geissler
2020-03-26 23:20 ` Andrew Jeffery
0 siblings, 1 reply; 6+ messages in thread
From: Andrew Geissler @ 2020-03-06 17:02 UTC (permalink / raw)
To: joel, devicetree, linux-arm-kernel, linux-aspeed, linux-kernel
Cc: linux-gpio, openbmc, Andrew Geissler
Name the GPIOs to help userspace work with them. The names describe the
functionality the lines provide, not the net or ball name. This makes it
easier to share userspace code across different systems and makes the
use of the lines more obvious.
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
---
arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts | 37 +++++++++++++++++++---
1 file changed, 33 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts b/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts
index bc60ec291681..4bcc82046362 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts
@@ -478,32 +478,61 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_gpioh_unbiased>;
+ gpio-line-names =
+ /*A0-A7*/ "","cfam-reset","","","","","","",
+ /*B0-B7*/ "","","","","","","","",
+ /*C0-C7*/ "","","","","","","","",
+ /*D0-D7*/ "fsi-enable","","","","","led-sys-boot-status","led-attention",
+ "led-fault",
+ /*E0-E7*/ "","","","","","","","presence-pcie-e2b",
+ /*F0-F7*/ "","","","","","","","checkstop",
+ /*G0-G7*/ "fsi-clock","fsi-data","","","","","","",
+ /*H0-H7*/ "onewire0","onewire1","onewire2","onewire3","","","","",
+ /*I0-I7*/ "","","","power-button","","","","",
+ /*J0-J7*/ "","","","","","","","",
+ /*K0-K7*/ "","","","","","","","",
+ /*L0-L7*/ "","","","","","","","",
+ /*M0-M7*/ "","","","","","","","",
+ /*N0-N7*/ "","","","","","","","",
+ /*O0-O7*/ "","","","","iso_u164_en","","fsi-trans","",
+ /*P0-P7*/ "ncsi_mux_en_n","bmc_i2c2_sw_rst_n","","bmc_i2c5_sw_rst_n","",
+ "","fsi-mux","",
+ /*Q0-Q7*/ "","","","","","","","",
+ /*R0-R7*/ "","","","","","","","",
+ /*S0-S7*/ "","","","","","","","",
+ /*T0-T7*/ "","","","","","","","",
+ /*U0-U7*/ "","","","","","","","",
+ /*V0-V7*/ "","","","","","","","",
+ /*W0-W7*/ "","","","","","","","",
+ /*X0-X7*/ "","","","","","","","",
+ /*Y0-Y7*/ "","","","","","","","",
+ /*Z0-Z7*/ "","","","","","","","",
+ /*AA0-AA7*/ "","","led-hdd-fault","","","","","",
+ /*AB0-AB7*/ "","","","","","","","",
+ /*AC0-AC7*/ "","","","","","","","";
+
line_iso_u146_en {
gpio-hog;
gpios = <ASPEED_GPIO(O, 4) GPIO_ACTIVE_HIGH>;
output-high;
- line-name = "iso_u164_en";
};
ncsi_mux_en_n {
gpio-hog;
gpios = <ASPEED_GPIO(P, 0) GPIO_ACTIVE_HIGH>;
output-low;
- line-name = "ncsi_mux_en_n";
};
line_bmc_i2c2_sw_rst_n {
gpio-hog;
gpios = <ASPEED_GPIO(P, 1) GPIO_ACTIVE_HIGH>;
output-high;
- line-name = "bmc_i2c2_sw_rst_n";
};
line_bmc_i2c5_sw_rst_n {
gpio-hog;
gpios = <ASPEED_GPIO(P, 3) GPIO_ACTIVE_HIGH>;
output-high;
- line-name = "bmc_i2c5_sw_rst_n";
};
};
--
2.21.0 (Apple Git-122)
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH 2/2] ARM: dts: aspeed: zaius: Add gpio line names
2020-03-06 17:02 ` [PATCH 2/2] ARM: dts: aspeed: zaius: " Andrew Geissler
@ 2020-03-26 23:20 ` Andrew Jeffery
2020-03-30 18:16 ` Andrew Geissler
0 siblings, 1 reply; 6+ messages in thread
From: Andrew Jeffery @ 2020-03-26 23:20 UTC (permalink / raw)
To: Andrew Geissler, Joel Stanley, devicetree, linux-arm-kernel,
linux-aspeed, linux-kernel
Cc: linux-gpio, openbmc, Andrew Geissler
On Sat, 7 Mar 2020, at 03:32, Andrew Geissler wrote:
> Name the GPIOs to help userspace work with them. The names describe the
> functionality the lines provide, not the net or ball name. This makes it
> easier to share userspace code across different systems and makes the
> use of the lines more obvious.
>
> Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
So we're creating a bit of an ad-hoc ABI here between the DT and userspace.
Where are we documenting it?
Generally I think the idea is good though, so:
Acked-by: Andrew Jeffery <andrew@aj.id.au>
> ---
> arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts | 37 +++++++++++++++++++---
> 1 file changed, 33 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts
> b/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts
> index bc60ec291681..4bcc82046362 100644
> --- a/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts
> +++ b/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts
> @@ -478,32 +478,61 @@
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_gpioh_unbiased>;
>
> + gpio-line-names =
> + /*A0-A7*/ "","cfam-reset","","","","","","",
> + /*B0-B7*/ "","","","","","","","",
> + /*C0-C7*/ "","","","","","","","",
> + /*D0-D7*/ "fsi-enable","","","","","led-sys-boot-status","led-attention",
> + "led-fault",
> + /*E0-E7*/ "","","","","","","","presence-pcie-e2b",
> + /*F0-F7*/ "","","","","","","","checkstop",
> + /*G0-G7*/ "fsi-clock","fsi-data","","","","","","",
> + /*H0-H7*/ "onewire0","onewire1","onewire2","onewire3","","","","",
> + /*I0-I7*/ "","","","power-button","","","","",
> + /*J0-J7*/ "","","","","","","","",
> + /*K0-K7*/ "","","","","","","","",
> + /*L0-L7*/ "","","","","","","","",
> + /*M0-M7*/ "","","","","","","","",
> + /*N0-N7*/ "","","","","","","","",
> + /*O0-O7*/ "","","","","iso_u164_en","","fsi-trans","",
> + /*P0-P7*/ "ncsi_mux_en_n","bmc_i2c2_sw_rst_n","","bmc_i2c5_sw_rst_n","",
> + "","fsi-mux","",
> + /*Q0-Q7*/ "","","","","","","","",
> + /*R0-R7*/ "","","","","","","","",
> + /*S0-S7*/ "","","","","","","","",
> + /*T0-T7*/ "","","","","","","","",
> + /*U0-U7*/ "","","","","","","","",
> + /*V0-V7*/ "","","","","","","","",
> + /*W0-W7*/ "","","","","","","","",
> + /*X0-X7*/ "","","","","","","","",
> + /*Y0-Y7*/ "","","","","","","","",
> + /*Z0-Z7*/ "","","","","","","","",
> + /*AA0-AA7*/ "","","led-hdd-fault","","","","","",
> + /*AB0-AB7*/ "","","","","","","","",
> + /*AC0-AC7*/ "","","","","","","","";
> +
> line_iso_u146_en {
> gpio-hog;
> gpios = <ASPEED_GPIO(O, 4) GPIO_ACTIVE_HIGH>;
> output-high;
> - line-name = "iso_u164_en";
> };
>
> ncsi_mux_en_n {
> gpio-hog;
> gpios = <ASPEED_GPIO(P, 0) GPIO_ACTIVE_HIGH>;
> output-low;
> - line-name = "ncsi_mux_en_n";
> };
>
> line_bmc_i2c2_sw_rst_n {
> gpio-hog;
> gpios = <ASPEED_GPIO(P, 1) GPIO_ACTIVE_HIGH>;
> output-high;
> - line-name = "bmc_i2c2_sw_rst_n";
> };
>
> line_bmc_i2c5_sw_rst_n {
> gpio-hog;
> gpios = <ASPEED_GPIO(P, 3) GPIO_ACTIVE_HIGH>;
> output-high;
> - line-name = "bmc_i2c5_sw_rst_n";
> };
> };
>
> --
> 2.21.0 (Apple Git-122)
>
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 2/2] ARM: dts: aspeed: zaius: Add gpio line names
2020-03-26 23:20 ` Andrew Jeffery
@ 2020-03-30 18:16 ` Andrew Geissler
2020-04-03 0:51 ` Andrew Jeffery
0 siblings, 1 reply; 6+ messages in thread
From: Andrew Geissler @ 2020-03-30 18:16 UTC (permalink / raw)
To: Andrew Jeffery
Cc: devicetree, linux-aspeed, openbmc, linux-kernel, linux-gpio,
Joel Stanley, linux-arm-kernel
> On Mar 26, 2020, at 6:20 PM, Andrew Jeffery <andrew@aj.id.au> wrote:
>
>
>
> On Sat, 7 Mar 2020, at 03:32, Andrew Geissler wrote:
>> Name the GPIOs to help userspace work with them. The names describe the
>> functionality the lines provide, not the net or ball name. This makes it
>> easier to share userspace code across different systems and makes the
>> use of the lines more obvious.
>>
>> Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
>
> So we're creating a bit of an ad-hoc ABI here between the DT and userspace.
>
> Where are we documenting it?
Yeah, so far it’s basically design by precedent. If you want your OpenBMC
function to work then follow the standards we're setting in other dts’s.
Is there a good place to document this? I could create a OpenBMC design
doc but that would not address non-OpenBMC areas.
>
> Generally I think the idea is good though, so:
>
> Acked-by: Andrew Jeffery <andrew@aj.id.au>
Thanks
>
>> ---
>> arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts | 37 +++++++++++++++++++---
>> 1 file changed, 33 insertions(+), 4 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts
>> b/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts
>> index bc60ec291681..4bcc82046362 100644
>> --- a/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts
>> +++ b/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts
>> @@ -478,32 +478,61 @@
>> pinctrl-names = "default";
>> pinctrl-0 = <&pinctrl_gpioh_unbiased>;
>>
>> + gpio-line-names =
>> + /*A0-A7*/ "","cfam-reset","","","","","","",
>> + /*B0-B7*/ "","","","","","","","",
>> + /*C0-C7*/ "","","","","","","","",
>> + /*D0-D7*/ "fsi-enable","","","","","led-sys-boot-status","led-attention",
>> + "led-fault",
>> + /*E0-E7*/ "","","","","","","","presence-pcie-e2b",
>> + /*F0-F7*/ "","","","","","","","checkstop",
>> + /*G0-G7*/ "fsi-clock","fsi-data","","","","","","",
>> + /*H0-H7*/ "onewire0","onewire1","onewire2","onewire3","","","","",
>> + /*I0-I7*/ "","","","power-button","","","","",
>> + /*J0-J7*/ "","","","","","","","",
>> + /*K0-K7*/ "","","","","","","","",
>> + /*L0-L7*/ "","","","","","","","",
>> + /*M0-M7*/ "","","","","","","","",
>> + /*N0-N7*/ "","","","","","","","",
>> + /*O0-O7*/ "","","","","iso_u164_en","","fsi-trans","",
>> + /*P0-P7*/ "ncsi_mux_en_n","bmc_i2c2_sw_rst_n","","bmc_i2c5_sw_rst_n","",
>> + "","fsi-mux","",
>> + /*Q0-Q7*/ "","","","","","","","",
>> + /*R0-R7*/ "","","","","","","","",
>> + /*S0-S7*/ "","","","","","","","",
>> + /*T0-T7*/ "","","","","","","","",
>> + /*U0-U7*/ "","","","","","","","",
>> + /*V0-V7*/ "","","","","","","","",
>> + /*W0-W7*/ "","","","","","","","",
>> + /*X0-X7*/ "","","","","","","","",
>> + /*Y0-Y7*/ "","","","","","","","",
>> + /*Z0-Z7*/ "","","","","","","","",
>> + /*AA0-AA7*/ "","","led-hdd-fault","","","","","",
>> + /*AB0-AB7*/ "","","","","","","","",
>> + /*AC0-AC7*/ "","","","","","","","";
>> +
>> line_iso_u146_en {
>> gpio-hog;
>> gpios = <ASPEED_GPIO(O, 4) GPIO_ACTIVE_HIGH>;
>> output-high;
>> - line-name = "iso_u164_en";
>> };
>>
>> ncsi_mux_en_n {
>> gpio-hog;
>> gpios = <ASPEED_GPIO(P, 0) GPIO_ACTIVE_HIGH>;
>> output-low;
>> - line-name = "ncsi_mux_en_n";
>> };
>>
>> line_bmc_i2c2_sw_rst_n {
>> gpio-hog;
>> gpios = <ASPEED_GPIO(P, 1) GPIO_ACTIVE_HIGH>;
>> output-high;
>> - line-name = "bmc_i2c2_sw_rst_n";
>> };
>>
>> line_bmc_i2c5_sw_rst_n {
>> gpio-hog;
>> gpios = <ASPEED_GPIO(P, 3) GPIO_ACTIVE_HIGH>;
>> output-high;
>> - line-name = "bmc_i2c5_sw_rst_n";
>> };
>> };
>>
>> --
>> 2.21.0 (Apple Git-122)
>>
>>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 2/2] ARM: dts: aspeed: zaius: Add gpio line names
2020-03-30 18:16 ` Andrew Geissler
@ 2020-04-03 0:51 ` Andrew Jeffery
2020-04-03 16:19 ` Andrew Geissler
0 siblings, 1 reply; 6+ messages in thread
From: Andrew Jeffery @ 2020-04-03 0:51 UTC (permalink / raw)
To: Andrew Geissler
Cc: devicetree, linux-aspeed, openbmc, linux-kernel, linux-gpio,
Joel Stanley, linux-arm-kernel
On Tue, 31 Mar 2020, at 04:46, Andrew Geissler wrote:
>
>
> > On Mar 26, 2020, at 6:20 PM, Andrew Jeffery <andrew@aj.id.au> wrote:
> >
> >
> >
> > On Sat, 7 Mar 2020, at 03:32, Andrew Geissler wrote:
> >> Name the GPIOs to help userspace work with them. The names describe the
> >> functionality the lines provide, not the net or ball name. This makes it
> >> easier to share userspace code across different systems and makes the
> >> use of the lines more obvious.
> >>
> >> Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
> >
> > So we're creating a bit of an ad-hoc ABI here between the DT and userspace.
> >
> > Where are we documenting it?
>
> Yeah, so far it’s basically design by precedent. If you want your OpenBMC
> function to work then follow the standards we're setting in other dts’s.
>
> Is there a good place to document this? I could create a OpenBMC design
> doc but that would not address non-OpenBMC areas.
Don't let perfect be the enemy of good enough :) Lets document it in OpenBMC
and then look at alternatives if we find it's necessary. I don't think we will given
that the contract is between the kernel and OpenBMC userspace.
Andrew
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 2/2] ARM: dts: aspeed: zaius: Add gpio line names
2020-04-03 0:51 ` Andrew Jeffery
@ 2020-04-03 16:19 ` Andrew Geissler
0 siblings, 0 replies; 6+ messages in thread
From: Andrew Geissler @ 2020-04-03 16:19 UTC (permalink / raw)
To: Andrew Jeffery
Cc: devicetree, linux-aspeed, OpenBMC Maillist,
Linux Kernel Mailing List, open list:GPIO SUBSYSTEM,
Joel Stanley, Linux ARM
> On Apr 2, 2020, at 7:51 PM, Andrew Jeffery <andrew@aj.id.au> wrote:
>
>
>
> On Tue, 31 Mar 2020, at 04:46, Andrew Geissler wrote:
>>
>>
>>> On Mar 26, 2020, at 6:20 PM, Andrew Jeffery <andrew@aj.id.au> wrote:
>>>
>>>
>>>
>>> On Sat, 7 Mar 2020, at 03:32, Andrew Geissler wrote:
>>>> Name the GPIOs to help userspace work with them. The names describe the
>>>> functionality the lines provide, not the net or ball name. This makes it
>>>> easier to share userspace code across different systems and makes the
>>>> use of the lines more obvious.
>>>>
>>>> Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
>>>
>>> So we're creating a bit of an ad-hoc ABI here between the DT and userspace.
>>>
>>> Where are we documenting it?
>>
>> Yeah, so far it’s basically design by precedent. If you want your OpenBMC
>> function to work then follow the standards we're setting in other dts’s.
>>
>> Is there a good place to document this? I could create a OpenBMC design
>> doc but that would not address non-OpenBMC areas.
>
> Don't let perfect be the enemy of good enough :) Lets document it in OpenBMC
> and then look at alternatives if we find it's necessary. I don't think we will given
> that the contract is between the kernel and OpenBMC userspace.
Ok, I put a doc up for review here:
https://gerrit.openbmc-project.xyz/c/openbmc/docs/+/30988
>
> Andrew
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2020-04-03 16:19 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-03-06 17:02 [PATCH 1/2] ARM: dts: aspeed: romulus: Add gpio line names Andrew Geissler
2020-03-06 17:02 ` [PATCH 2/2] ARM: dts: aspeed: zaius: " Andrew Geissler
2020-03-26 23:20 ` Andrew Jeffery
2020-03-30 18:16 ` Andrew Geissler
2020-04-03 0:51 ` Andrew Jeffery
2020-04-03 16:19 ` Andrew Geissler
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).