From: Vinod Koul <vkoul@kernel.org>
To: Stephen Boyd <sboyd@kernel.org>
Cc: linux-arm-msm@vger.kernel.org,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Vinod Koul <vkoul@kernel.org>, Andy Gross <agross@kernel.org>,
Michael Turquette <mturquette@baylibre.com>,
Rob Herring <robh+dt@kernel.org>,
Taniya Das <tdas@codeaurora.org>,
AngeloGioacchino Del Regno
<angelogioacchino.delregno@somainline.org>,
linux-clk@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: [PATCH v5 1/5] clk: qcom: clk-alpha-pll: replace regval with val
Date: Wed, 27 Jan 2021 12:38:07 +0530 [thread overview]
Message-ID: <20210127070811.152690-2-vkoul@kernel.org> (raw)
In-Reply-To: <20210127070811.152690-1-vkoul@kernel.org>
Driver uses regval variable for holding register values, replace with a
shorter one val
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
---
drivers/clk/qcom/clk-alpha-pll.c | 20 ++++++++++----------
1 file changed, 10 insertions(+), 10 deletions(-)
diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
index 21c357c26ec4..f7721088494c 100644
--- a/drivers/clk/qcom/clk-alpha-pll.c
+++ b/drivers/clk/qcom/clk-alpha-pll.c
@@ -777,15 +777,15 @@ static long alpha_pll_huayra_round_rate(struct clk_hw *hw, unsigned long rate,
static int trion_pll_is_enabled(struct clk_alpha_pll *pll,
struct regmap *regmap)
{
- u32 mode_regval, opmode_regval;
+ u32 mode_val, opmode_val;
int ret;
- ret = regmap_read(regmap, PLL_MODE(pll), &mode_regval);
- ret |= regmap_read(regmap, PLL_OPMODE(pll), &opmode_regval);
+ ret = regmap_read(regmap, PLL_MODE(pll), &mode_val);
+ ret |= regmap_read(regmap, PLL_OPMODE(pll), &opmode_val);
if (ret)
return 0;
- return ((opmode_regval & PLL_RUN) && (mode_regval & PLL_OUTCTRL));
+ return ((opmode_val & PLL_RUN) && (mode_val & PLL_OUTCTRL));
}
static int clk_trion_pll_is_enabled(struct clk_hw *hw)
@@ -1445,12 +1445,12 @@ EXPORT_SYMBOL_GPL(clk_trion_pll_configure);
static int __alpha_pll_trion_prepare(struct clk_hw *hw, u32 pcal_done)
{
struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
- u32 regval;
+ u32 val;
int ret;
/* Return early if calibration is not needed. */
- regmap_read(pll->clkr.regmap, PLL_STATUS(pll), ®val);
- if (regval & pcal_done)
+ regmap_read(pll->clkr.regmap, PLL_STATUS(pll), &val);
+ if (val & pcal_done)
return 0;
/* On/off to calibrate */
@@ -1476,7 +1476,7 @@ static int alpha_pll_trion_set_rate(struct clk_hw *hw, unsigned long rate,
{
struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
unsigned long rrate;
- u32 regval, l, alpha_width = pll_alpha_width(pll);
+ u32 val, l, alpha_width = pll_alpha_width(pll);
u64 a;
int ret;
@@ -1497,8 +1497,8 @@ static int alpha_pll_trion_set_rate(struct clk_hw *hw, unsigned long rate,
/* Wait for 2 reference cycles before checking the ACK bit. */
udelay(1);
- regmap_read(pll->clkr.regmap, PLL_MODE(pll), ®val);
- if (!(regval & ALPHA_PLL_ACK_LATCH)) {
+ regmap_read(pll->clkr.regmap, PLL_MODE(pll), &val);
+ if (!(val & ALPHA_PLL_ACK_LATCH)) {
pr_err("Lucid PLL latch failed. Output may be unstable!\n");
return -EINVAL;
}
--
2.26.2
next prev parent reply other threads:[~2021-01-27 7:12 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-01-27 7:08 [PATCH v5 0/5] Add clock drivers for SM8350 Vinod Koul
2021-01-27 7:08 ` Vinod Koul [this message]
2021-02-08 18:07 ` [PATCH v5 1/5] clk: qcom: clk-alpha-pll: replace regval with val Stephen Boyd
2021-01-27 7:08 ` [PATCH v5 2/5] clk: qcom: clk-alpha-pll: modularize alpha_pll_trion_set_rate() Vinod Koul
2021-02-08 18:06 ` Stephen Boyd
2021-01-27 7:08 ` [PATCH v5 3/5] clk: qcom: clk-alpha-pll: Add support for Lucid 5LPE PLL Vinod Koul
2021-02-08 18:06 ` Stephen Boyd
2021-01-27 7:08 ` [PATCH v5 4/5] dt-bindings: clock: Add SM8350 GCC clock bindings Vinod Koul
2021-02-08 18:07 ` Stephen Boyd
[not found] ` <20210127070811.152690-6-vkoul@kernel.org>
2021-02-08 18:07 ` [PATCH v5 5/5] clk: qcom: gcc: Add clock driver for SM8350 Stephen Boyd
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210127070811.152690-2-vkoul@kernel.org \
--to=vkoul@kernel.org \
--cc=agross@kernel.org \
--cc=angelogioacchino.delregno@somainline.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mturquette@baylibre.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
--cc=tdas@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).