From: Vinod Koul <vkoul@kernel.org>
To: Stephen Boyd <sboyd@kernel.org>
Cc: linux-arm-msm@vger.kernel.org,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Vivek Aknurwar <viveka@codeaurora.org>,
Andy Gross <agross@kernel.org>,
Michael Turquette <mturquette@baylibre.com>,
Rob Herring <robh+dt@kernel.org>,
Taniya Das <tdas@codeaurora.org>,
AngeloGioacchino Del Regno
<angelogioacchino.delregno@somainline.org>,
linux-clk@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Jeevan Shriram <jshriram@codeaurora.org>,
Vinod Koul <vkoul@kernel.org>
Subject: [PATCH v5 3/5] clk: qcom: clk-alpha-pll: Add support for Lucid 5LPE PLL
Date: Wed, 27 Jan 2021 12:38:09 +0530 [thread overview]
Message-ID: <20210127070811.152690-4-vkoul@kernel.org> (raw)
In-Reply-To: <20210127070811.152690-1-vkoul@kernel.org>
From: Vivek Aknurwar <viveka@codeaurora.org>
Lucid 5LPE is a slightly different Lucid PLL with different offsets and
porgramming sequence so add support for these
Signed-off-by: Vivek Aknurwar <viveka@codeaurora.org>
Signed-off-by: Jeevan Shriram <jshriram@codeaurora.org>
[vkoul: rebase and tidy up for upstream]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
drivers/clk/qcom/clk-alpha-pll.c | 173 +++++++++++++++++++++++++++++++
drivers/clk/qcom/clk-alpha-pll.h | 4 +
2 files changed, 177 insertions(+)
diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
index a30ea7b09224..c6eb99169ddc 100644
--- a/drivers/clk/qcom/clk-alpha-pll.c
+++ b/drivers/clk/qcom/clk-alpha-pll.c
@@ -156,6 +156,12 @@ EXPORT_SYMBOL_GPL(clk_alpha_pll_regs);
/* LUCID PLL specific settings and offsets */
#define LUCID_PCAL_DONE BIT(27)
+/* LUCID 5LPE PLL specific settings and offsets */
+#define LUCID_5LPE_PCAL_DONE BIT(11)
+#define LUCID_5LPE_ALPHA_PLL_ACK_LATCH BIT(13)
+#define LUCID_5LPE_PLL_LATCH_INPUT BIT(14)
+#define LUCID_5LPE_ENABLE_VOTE_RUN BIT(21)
+
#define pll_alpha_width(p) \
((PLL_ALPHA_VAL_U(p) - PLL_ALPHA_VAL(p) == 4) ? \
ALPHA_REG_BITWIDTH : ALPHA_REG_16BIT_WIDTH)
@@ -1604,3 +1610,170 @@ const struct clk_ops clk_alpha_pll_agera_ops = {
.set_rate = clk_alpha_pll_agera_set_rate,
};
EXPORT_SYMBOL_GPL(clk_alpha_pll_agera_ops);
+
+static int alpha_pll_lucid_5lpe_enable(struct clk_hw *hw)
+{
+ struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
+ u32 val;
+ int ret;
+
+ ret = regmap_read(pll->clkr.regmap, PLL_USER_CTL(pll), &val);
+ if (ret)
+ return ret;
+
+ /* If in FSM mode, just vote for it */
+ if (val & LUCID_5LPE_ENABLE_VOTE_RUN) {
+ ret = clk_enable_regmap(hw);
+ if (ret)
+ return ret;
+ return wait_for_pll_enable_lock(pll);
+ }
+
+ /* Check if PLL is already enabled, return if enabled */
+ ret = trion_pll_is_enabled(pll, pll->clkr.regmap);
+ if (ret < 0)
+ return ret;
+
+ ret = regmap_update_bits(pll->clkr.regmap, PLL_MODE(pll), PLL_RESET_N, PLL_RESET_N);
+ if (ret)
+ return ret;
+
+ regmap_write(pll->clkr.regmap, PLL_OPMODE(pll), PLL_RUN);
+
+ ret = wait_for_pll_enable_lock(pll);
+ if (ret)
+ return ret;
+
+ /* Enable the PLL outputs */
+ ret = regmap_update_bits(pll->clkr.regmap, PLL_USER_CTL(pll), PLL_OUT_MASK, PLL_OUT_MASK);
+ if (ret)
+ return ret;
+
+ /* Enable the global PLL outputs */
+ return regmap_update_bits(pll->clkr.regmap, PLL_MODE(pll), PLL_OUTCTRL, PLL_OUTCTRL);
+}
+
+static void alpha_pll_lucid_5lpe_disable(struct clk_hw *hw)
+{
+ struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
+ u32 val;
+ int ret;
+
+ ret = regmap_read(pll->clkr.regmap, PLL_USER_CTL(pll), &val);
+ if (ret)
+ return;
+
+ /* If in FSM mode, just unvote it */
+ if (val & LUCID_5LPE_ENABLE_VOTE_RUN) {
+ clk_disable_regmap(hw);
+ return;
+ }
+
+ /* Disable the global PLL output */
+ ret = regmap_update_bits(pll->clkr.regmap, PLL_MODE(pll), PLL_OUTCTRL, 0);
+ if (ret)
+ return;
+
+ /* Disable the PLL outputs */
+ ret = regmap_update_bits(pll->clkr.regmap, PLL_USER_CTL(pll), PLL_OUT_MASK, 0);
+ if (ret)
+ return;
+
+ /* Place the PLL mode in STANDBY */
+ regmap_write(pll->clkr.regmap, PLL_OPMODE(pll), PLL_STANDBY);
+}
+
+/*
+ * The Lucid 5LPE PLL requires a power-on self-calibration which happens
+ * when the PLL comes out of reset. Calibrate in case it is not completed.
+ */
+static int alpha_pll_lucid_5lpe_prepare(struct clk_hw *hw)
+{
+ struct clk_alpha_pll *pll = to_clk_alpha_pll(hw);
+ struct clk_hw *p;
+ u32 val = 0;
+ int ret;
+
+ /* Return early if calibration is not needed. */
+ regmap_read(pll->clkr.regmap, PLL_MODE(pll), &val);
+ if (val & LUCID_5LPE_PCAL_DONE)
+ return 0;
+
+ p = clk_hw_get_parent(hw);
+ if (!p)
+ return -EINVAL;
+
+ ret = alpha_pll_lucid_5lpe_enable(hw);
+ if (ret)
+ return ret;
+
+ alpha_pll_lucid_5lpe_disable(hw);
+
+ return 0;
+}
+
+static int alpha_pll_lucid_5lpe_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long prate)
+{
+ return __alpha_pll_trion_set_rate(hw, rate, prate,
+ LUCID_5LPE_PLL_LATCH_INPUT,
+ LUCID_5LPE_ALPHA_PLL_ACK_LATCH);
+}
+
+static int clk_lucid_5lpe_pll_postdiv_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct clk_alpha_pll_postdiv *pll = to_clk_alpha_pll_postdiv(hw);
+ int i, val = 0, div, ret;
+ u32 mask;
+
+ /*
+ * If the PLL is in FSM mode, then treat set_rate callback as a
+ * no-operation.
+ */
+ ret = regmap_read(pll->clkr.regmap, PLL_USER_CTL(pll), &val);
+ if (ret)
+ return ret;
+
+ if (val & LUCID_5LPE_ENABLE_VOTE_RUN)
+ return 0;
+
+ div = DIV_ROUND_UP_ULL((u64)parent_rate, rate);
+ for (i = 0; i < pll->num_post_div; i++) {
+ if (pll->post_div_table[i].div == div) {
+ val = pll->post_div_table[i].val;
+ break;
+ }
+ }
+
+ mask = GENMASK(pll->width + pll->post_div_shift - 1, pll->post_div_shift);
+ return regmap_update_bits(pll->clkr.regmap, PLL_USER_CTL(pll),
+ mask, val << pll->post_div_shift);
+}
+
+const struct clk_ops clk_alpha_pll_lucid_5lpe_ops = {
+ .prepare = alpha_pll_lucid_5lpe_prepare,
+ .enable = alpha_pll_lucid_5lpe_enable,
+ .disable = alpha_pll_lucid_5lpe_disable,
+ .is_enabled = clk_trion_pll_is_enabled,
+ .recalc_rate = clk_trion_pll_recalc_rate,
+ .round_rate = clk_alpha_pll_round_rate,
+ .set_rate = alpha_pll_lucid_5lpe_set_rate,
+};
+EXPORT_SYMBOL(clk_alpha_pll_lucid_5lpe_ops);
+
+const struct clk_ops clk_alpha_pll_fixed_lucid_5lpe_ops = {
+ .enable = alpha_pll_lucid_5lpe_enable,
+ .disable = alpha_pll_lucid_5lpe_disable,
+ .is_enabled = clk_trion_pll_is_enabled,
+ .recalc_rate = clk_trion_pll_recalc_rate,
+ .round_rate = clk_alpha_pll_round_rate,
+};
+EXPORT_SYMBOL(clk_alpha_pll_fixed_lucid_5lpe_ops);
+
+const struct clk_ops clk_alpha_pll_postdiv_lucid_5lpe_ops = {
+ .recalc_rate = clk_alpha_pll_postdiv_fabia_recalc_rate,
+ .round_rate = clk_alpha_pll_postdiv_fabia_round_rate,
+ .set_rate = clk_lucid_5lpe_pll_postdiv_set_rate,
+};
+EXPORT_SYMBOL(clk_alpha_pll_postdiv_lucid_5lpe_ops);
diff --git a/drivers/clk/qcom/clk-alpha-pll.h b/drivers/clk/qcom/clk-alpha-pll.h
index 0ea30d2f3da1..6943e933be0f 100644
--- a/drivers/clk/qcom/clk-alpha-pll.h
+++ b/drivers/clk/qcom/clk-alpha-pll.h
@@ -144,6 +144,10 @@ extern const struct clk_ops clk_alpha_pll_lucid_ops;
extern const struct clk_ops clk_alpha_pll_postdiv_lucid_ops;
extern const struct clk_ops clk_alpha_pll_agera_ops;
+extern const struct clk_ops clk_alpha_pll_lucid_5lpe_ops;
+extern const struct clk_ops clk_alpha_pll_fixed_lucid_5lpe_ops;
+extern const struct clk_ops clk_alpha_pll_postdiv_lucid_5lpe_ops;
+
void clk_alpha_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
const struct alpha_pll_config *config);
void clk_fabia_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
--
2.26.2
next prev parent reply other threads:[~2021-01-27 7:13 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-01-27 7:08 [PATCH v5 0/5] Add clock drivers for SM8350 Vinod Koul
2021-01-27 7:08 ` [PATCH v5 1/5] clk: qcom: clk-alpha-pll: replace regval with val Vinod Koul
2021-02-08 18:07 ` Stephen Boyd
2021-01-27 7:08 ` [PATCH v5 2/5] clk: qcom: clk-alpha-pll: modularize alpha_pll_trion_set_rate() Vinod Koul
2021-02-08 18:06 ` Stephen Boyd
2021-01-27 7:08 ` Vinod Koul [this message]
2021-02-08 18:06 ` [PATCH v5 3/5] clk: qcom: clk-alpha-pll: Add support for Lucid 5LPE PLL Stephen Boyd
2021-01-27 7:08 ` [PATCH v5 4/5] dt-bindings: clock: Add SM8350 GCC clock bindings Vinod Koul
2021-02-08 18:07 ` Stephen Boyd
[not found] ` <20210127070811.152690-6-vkoul@kernel.org>
2021-02-08 18:07 ` [PATCH v5 5/5] clk: qcom: gcc: Add clock driver for SM8350 Stephen Boyd
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210127070811.152690-4-vkoul@kernel.org \
--to=vkoul@kernel.org \
--cc=agross@kernel.org \
--cc=angelogioacchino.delregno@somainline.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=jshriram@codeaurora.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mturquette@baylibre.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
--cc=tdas@codeaurora.org \
--cc=viveka@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).