* [PATCH v3 2/2] dt-bindings: iio: adc: Add docs for AD7606 ADC
@ 2018-11-29 16:57 Stefan Popa
2018-12-01 17:00 ` Jonathan Cameron
2018-12-07 23:47 ` Rob Herring
0 siblings, 2 replies; 4+ messages in thread
From: Stefan Popa @ 2018-11-29 16:57 UTC (permalink / raw)
To: jic23, robh+dt, mark.rutland
Cc: knaack.h, lars, pmeerw, Michael.Hennerich, gregkh, linux-iio,
devicetree, linux-kernel, stefan.popa
Document support for AD7606 Analog to Digital Converter.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
---
Changes in v2:
- fixed indentation issues.
- used gpios instead of gpio.
- added vendor prefix for conversion-start-gpios, first-data-gpios,
and range-gpios.
Changes in v3:
- Added adi,oversampling-ratio-gpios.
.../devicetree/bindings/iio/adc/adi,ad7606.txt | 54 ++++++++++++++++++++++
MAINTAINERS | 1 +
2 files changed, 55 insertions(+)
create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
new file mode 100644
index 0000000..02fae23
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
@@ -0,0 +1,54 @@
+Analog Devices AD7606 Simultaneous Sampling ADC
+
+Required properties for the AD7606:
+
+- compatible: Must be one of
+ * "adi,ad7605-4"
+ * "adi,ad7606-8"
+ * "adi,ad7606-6"
+ * "adi,ad7606-4"
+- reg: SPI chip select number for the device
+- spi-max-frequency: Max SPI frequency to use
+ see: Documentation/devicetree/bindings/spi/spi-bus.txt
+- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt
+- avcc-supply: phandle to the Avcc power supply
+- interrupts: IRQ line for the ADC
+ see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+- adi,conversion-start-gpios: must be the device tree identifier of the CONVST pin.
+ This logic input is used to initiate conversions on the analog
+ input channels.
+
+Optional properties:
+
+- reset-gpios: must be the device tree identifier of the RESET pin. If specified,
+ it will be asserted during driver probe.
+- standby-gpios: must be the device tree identifier of the STBY pin. This pin is used
+ to place the AD7606 into one of two power-down modes, Standby mode or
+ Shutdown mode.
+- adi,first-data-gpios: must be the device tree identifier of the FRSTDATA pin.
+ The FRSTDATA output indicates when the first channel, V1, is
+ being read back on either the parallel, byte or serial interface.
+- adi,range-gpios: must be the device tree identifier of the RANGE pin. The polarity on
+ this pin determines the input range of the analog input channels. If
+ this pin is tied to a logic high, the analog input range is ±10V for
+ all channels. If this pin is tied to a logic low, the analog input range
+ is ±5V for all channels.
+
+Example:
+
+ adc@0 {
+ compatible = "adi,ad7606-8";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ spi-cpol;
+
+ avcc-supply = <&adc_vref>;
+
+ interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-parent = <&gpio>;
+
+ adi,conversion-start-gpios = <&gpio 17 0>;
+ reset-gpios = <&gpio 27 0>;
+ adi,first-data-gpios = <&gpio 22 0>;
+ standby-gpios = <&gpio 24 0>;
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 843545d..6d63db4 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -845,6 +845,7 @@ L: linux-iio@vger.kernel.org
W: http://ez.analog.com/community/linux-device-drivers
S: Supported
F: drivers/iio/adc/ad7606.c
+F: Documentation/devicetree/bindings/iio/adc/ad7606.txt
ANALOG DEVICES INC AD9389B DRIVER
M: Hans Verkuil <hans.verkuil@cisco.com>
--
2.7.4
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH v3 2/2] dt-bindings: iio: adc: Add docs for AD7606 ADC
2018-11-29 16:57 [PATCH v3 2/2] dt-bindings: iio: adc: Add docs for AD7606 ADC Stefan Popa
@ 2018-12-01 17:00 ` Jonathan Cameron
2018-12-01 17:00 ` Jonathan Cameron
2018-12-07 23:47 ` Rob Herring
1 sibling, 1 reply; 4+ messages in thread
From: Jonathan Cameron @ 2018-12-01 17:00 UTC (permalink / raw)
To: Stefan Popa
Cc: robh+dt, mark.rutland, knaack.h, lars, pmeerw, Michael.Hennerich,
gregkh, linux-iio, devicetree, linux-kernel
On Thu, 29 Nov 2018 18:57:43 +0200
Stefan Popa <stefan.popa@analog.com> wrote:
> Document support for AD7606 Analog to Digital Converter.
>=20
> Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Looks good to me, but as it's a non trivial binding in complexity I'd
definitely like a DT maintainers input before applying this.
Thanks,
Jonathan
> ---
> Changes in v2:
> - fixed indentation issues.
> - used gpios instead of gpio.
> - added vendor prefix for conversion-start-gpios, first-data-gpios,
> and range-gpios.
> Changes in v3:
> - Added adi,oversampling-ratio-gpios.
>=20
> .../devicetree/bindings/iio/adc/adi,ad7606.txt | 54 ++++++++++++++++=
++++++
> MAINTAINERS | 1 +
> 2 files changed, 55 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7606.=
txt
>=20
> diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt b/D=
ocumentation/devicetree/bindings/iio/adc/adi,ad7606.txt
> new file mode 100644
> index 0000000..02fae23
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
> @@ -0,0 +1,54 @@
> +Analog Devices AD7606 Simultaneous Sampling ADC
> +
> +Required properties for the AD7606:
> +
> +- compatible: Must be one of
> + * "adi,ad7605-4"
> + * "adi,ad7606-8"
> + * "adi,ad7606-6"
> + * "adi,ad7606-4"
> +- reg: SPI chip select number for the device
> +- spi-max-frequency: Max SPI frequency to use
> + see: Documentation/devicetree/bindings/spi/spi-bus.txt
> +- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt
> +- avcc-supply: phandle to the Avcc power supply
> +- interrupts: IRQ line for the ADC
> + see: Documentation/devicetree/bindings/interrupt-controller/interrupts.=
txt
> +- adi,conversion-start-gpios: must be the device tree identifier of the =
CONVST pin.
> + This logic input is used to initiate conversions on the analog
> + input channels.
> +
> +Optional properties:
> +
> +- reset-gpios: must be the device tree identifier of the RESET pin. If s=
pecified,
> + it will be asserted during driver probe.
> +- standby-gpios: must be the device tree identifier of the STBY pin. Thi=
s pin is used
> + to place the AD7606 into one of two power-down modes, Standby mode or
> + Shutdown mode.
> +- adi,first-data-gpios: must be the device tree identifier of the FRSTDA=
TA pin.
> + The FRSTDATA output indicates when the first channel, V1, is
> + being read back on either the parallel, byte or serial interface.
> +- adi,range-gpios: must be the device tree identifier of the RANGE pin. =
The polarity on
> + this pin determines the input range of the analog input channels.=
If
> + this pin is tied to a logic high, the analog input range is =C2=
=B110V for
> + all channels. If this pin is tied to a logic low, the analog inpu=
t range
> + is =C2=B15V for all channels.
> +
> +Example:
> +
> + adc@0 {
> + compatible =3D "adi,ad7606-8";
> + reg =3D <0>;
> + spi-max-frequency =3D <1000000>;
> + spi-cpol;
> +
> + avcc-supply =3D <&adc_vref>;
> +
> + interrupts =3D <25 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-parent =3D <&gpio>;
> +
> + adi,conversion-start-gpios =3D <&gpio 17 0>;
> + reset-gpios =3D <&gpio 27 0>;
> + adi,first-data-gpios =3D <&gpio 22 0>;
> + standby-gpios =3D <&gpio 24 0>;
> + };
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 843545d..6d63db4 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -845,6 +845,7 @@ L: linux-iio@vger.kernel.org
> W: http://ez.analog.com/community/linux-device-drivers
> S: Supported
> F: drivers/iio/adc/ad7606.c
> +F: Documentation/devicetree/bindings/iio/adc/ad7606.txt
> =20
> ANALOG DEVICES INC AD9389B DRIVER
> M: Hans Verkuil <hans.verkuil@cisco.com>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH v3 2/2] dt-bindings: iio: adc: Add docs for AD7606 ADC
2018-12-01 17:00 ` Jonathan Cameron
@ 2018-12-01 17:00 ` Jonathan Cameron
0 siblings, 0 replies; 4+ messages in thread
From: Jonathan Cameron @ 2018-12-01 17:00 UTC (permalink / raw)
To: Stefan Popa
Cc: robh+dt, mark.rutland, knaack.h, lars, pmeerw, Michael.Hennerich,
gregkh, linux-iio, devicetree, linux-kernel
On Thu, 29 Nov 2018 18:57:43 +0200
Stefan Popa <stefan.popa@analog.com> wrote:
> Document support for AD7606 Analog to Digital Converter.
>
> Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Looks good to me, but as it's a non trivial binding in complexity I'd
definitely like a DT maintainers input before applying this.
Thanks,
Jonathan
> ---
> Changes in v2:
> - fixed indentation issues.
> - used gpios instead of gpio.
> - added vendor prefix for conversion-start-gpios, first-data-gpios,
> and range-gpios.
> Changes in v3:
> - Added adi,oversampling-ratio-gpios.
>
> .../devicetree/bindings/iio/adc/adi,ad7606.txt | 54 ++++++++++++++++++++++
> MAINTAINERS | 1 +
> 2 files changed, 55 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
> new file mode 100644
> index 0000000..02fae23
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
> @@ -0,0 +1,54 @@
> +Analog Devices AD7606 Simultaneous Sampling ADC
> +
> +Required properties for the AD7606:
> +
> +- compatible: Must be one of
> + * "adi,ad7605-4"
> + * "adi,ad7606-8"
> + * "adi,ad7606-6"
> + * "adi,ad7606-4"
> +- reg: SPI chip select number for the device
> +- spi-max-frequency: Max SPI frequency to use
> + see: Documentation/devicetree/bindings/spi/spi-bus.txt
> +- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt
> +- avcc-supply: phandle to the Avcc power supply
> +- interrupts: IRQ line for the ADC
> + see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
> +- adi,conversion-start-gpios: must be the device tree identifier of the CONVST pin.
> + This logic input is used to initiate conversions on the analog
> + input channels.
> +
> +Optional properties:
> +
> +- reset-gpios: must be the device tree identifier of the RESET pin. If specified,
> + it will be asserted during driver probe.
> +- standby-gpios: must be the device tree identifier of the STBY pin. This pin is used
> + to place the AD7606 into one of two power-down modes, Standby mode or
> + Shutdown mode.
> +- adi,first-data-gpios: must be the device tree identifier of the FRSTDATA pin.
> + The FRSTDATA output indicates when the first channel, V1, is
> + being read back on either the parallel, byte or serial interface.
> +- adi,range-gpios: must be the device tree identifier of the RANGE pin. The polarity on
> + this pin determines the input range of the analog input channels. If
> + this pin is tied to a logic high, the analog input range is ±10V for
> + all channels. If this pin is tied to a logic low, the analog input range
> + is ±5V for all channels.
> +
> +Example:
> +
> + adc@0 {
> + compatible = "adi,ad7606-8";
> + reg = <0>;
> + spi-max-frequency = <1000000>;
> + spi-cpol;
> +
> + avcc-supply = <&adc_vref>;
> +
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-parent = <&gpio>;
> +
> + adi,conversion-start-gpios = <&gpio 17 0>;
> + reset-gpios = <&gpio 27 0>;
> + adi,first-data-gpios = <&gpio 22 0>;
> + standby-gpios = <&gpio 24 0>;
> + };
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 843545d..6d63db4 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -845,6 +845,7 @@ L: linux-iio@vger.kernel.org
> W: http://ez.analog.com/community/linux-device-drivers
> S: Supported
> F: drivers/iio/adc/ad7606.c
> +F: Documentation/devicetree/bindings/iio/adc/ad7606.txt
>
> ANALOG DEVICES INC AD9389B DRIVER
> M: Hans Verkuil <hans.verkuil@cisco.com>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [PATCH v3 2/2] dt-bindings: iio: adc: Add docs for AD7606 ADC
2018-11-29 16:57 [PATCH v3 2/2] dt-bindings: iio: adc: Add docs for AD7606 ADC Stefan Popa
2018-12-01 17:00 ` Jonathan Cameron
@ 2018-12-07 23:47 ` Rob Herring
1 sibling, 0 replies; 4+ messages in thread
From: Rob Herring @ 2018-12-07 23:47 UTC (permalink / raw)
To: Stefan Popa
Cc: jic23, mark.rutland, knaack.h, lars, pmeerw, Michael.Hennerich,
gregkh, linux-iio, devicetree, linux-kernel
On Thu, Nov 29, 2018 at 06:57:43PM +0200, Stefan Popa wrote:
> Document support for AD7606 Analog to Digital Converter.
>
> Signed-off-by: Stefan Popa <stefan.popa@analog.com>
> ---
> Changes in v2:
> - fixed indentation issues.
> - used gpios instead of gpio.
> - added vendor prefix for conversion-start-gpios, first-data-gpios,
> and range-gpios.
> Changes in v3:
> - Added adi,oversampling-ratio-gpios.
>
> .../devicetree/bindings/iio/adc/adi,ad7606.txt | 54 ++++++++++++++++++++++
> MAINTAINERS | 1 +
> 2 files changed, 55 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
>
> diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
> new file mode 100644
> index 0000000..02fae23
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.txt
> @@ -0,0 +1,54 @@
> +Analog Devices AD7606 Simultaneous Sampling ADC
> +
> +Required properties for the AD7606:
> +
> +- compatible: Must be one of
> + * "adi,ad7605-4"
> + * "adi,ad7606-8"
> + * "adi,ad7606-6"
> + * "adi,ad7606-4"
> +- reg: SPI chip select number for the device
> +- spi-max-frequency: Max SPI frequency to use
> + see: Documentation/devicetree/bindings/spi/spi-bus.txt
> +- spi-cpha: See Documentation/devicetree/bindings/spi/spi-bus.txt
> +- avcc-supply: phandle to the Avcc power supply
> +- interrupts: IRQ line for the ADC
> + see: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
> +- adi,conversion-start-gpios: must be the device tree identifier of the CONVST pin.
> + This logic input is used to initiate conversions on the analog
> + input channels.
Needs to say active high or low and set the flag appropriately.
> +
> +Optional properties:
> +
> +- reset-gpios: must be the device tree identifier of the RESET pin. If specified,
> + it will be asserted during driver probe.
active high or low?
> +- standby-gpios: must be the device tree identifier of the STBY pin. This pin is used
> + to place the AD7606 into one of two power-down modes, Standby mode or
> + Shutdown mode.
active high or low?
> +- adi,first-data-gpios: must be the device tree identifier of the FRSTDATA pin.
> + The FRSTDATA output indicates when the first channel, V1, is
> + being read back on either the parallel, byte or serial interface.
active high or low?
> +- adi,range-gpios: must be the device tree identifier of the RANGE pin. The polarity on
> + this pin determines the input range of the analog input channels. If
> + this pin is tied to a logic high, the analog input range is ±10V for
> + all channels. If this pin is tied to a logic low, the analog input range
> + is ±5V for all channels.
> +
> +Example:
> +
> + adc@0 {
> + compatible = "adi,ad7606-8";
> + reg = <0>;
> + spi-max-frequency = <1000000>;
> + spi-cpol;
> +
> + avcc-supply = <&adc_vref>;
> +
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-parent = <&gpio>;
> +
> + adi,conversion-start-gpios = <&gpio 17 0>;
> + reset-gpios = <&gpio 27 0>;
> + adi,first-data-gpios = <&gpio 22 0>;
> + standby-gpios = <&gpio 24 0>;
> + };
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 843545d..6d63db4 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -845,6 +845,7 @@ L: linux-iio@vger.kernel.org
> W: http://ez.analog.com/community/linux-device-drivers
> S: Supported
> F: drivers/iio/adc/ad7606.c
> +F: Documentation/devicetree/bindings/iio/adc/ad7606.txt
>
> ANALOG DEVICES INC AD9389B DRIVER
> M: Hans Verkuil <hans.verkuil@cisco.com>
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2018-12-07 23:47 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2018-11-29 16:57 [PATCH v3 2/2] dt-bindings: iio: adc: Add docs for AD7606 ADC Stefan Popa
2018-12-01 17:00 ` Jonathan Cameron
2018-12-01 17:00 ` Jonathan Cameron
2018-12-07 23:47 ` Rob Herring
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).