From: Xingyu Wu <xingyu.wu@starfivetech.com>
To: <linux-riscv@lists.infradead.org>, <devicetree@vger.kernel.org>,
"Michael Turquette" <mturquette@baylibre.com>,
Stephen Boyd <sboyd@kernel.org>,
"Rob Herring" <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Philipp Zabel <p.zabel@pengutronix.de>,
Conor Dooley <conor@kernel.org>,
Emil Renner Berthing <emil.renner.berthing@canonical.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>,
Palmer Dabbelt <palmer@dabbelt.com>,
Albert Ou <aou@eecs.berkeley.edu>,
Hal Feng <hal.feng@starfivetech.com>,
Xingyu Wu <xingyu.wu@starfivetech.com>,
"William Qiu" <william.qiu@starfivetech.com>,
<linux-kernel@vger.kernel.org>, <linux-clk@vger.kernel.org>
Subject: [PATCH v7 0/7] Add PLL clocks driver and syscon for StarFive JH7110 SoC
Date: Mon, 17 Jul 2023 10:30:33 +0800 [thread overview]
Message-ID: <20230717023040.78860-1-xingyu.wu@starfivetech.com> (raw)
This patch serises are to add PLL clocks driver and providers by writing
and reading syscon registers for the StarFive JH7110 RISC-V SoC. And add
documentation and nodes to describe StarFive System Controller(syscon)
Registers. This patch serises are based on Linux 6.4.
PLLs are high speed, low jitter frequency synthesizers in JH7110.
Each PLL clock works in integer mode or fraction mode by some dividers,
and the dividers are set in several syscon registers.
The formula for calculating frequency is:
Fvco = Fref * (NI + NF) / M / Q1
The first patch adds docunmentation to describe PLL clock bindings,
and the second patch adds documentation to decribe syscon registers.
The patch 3 modifies the SYSCRG bindings and adds PLL clock inputs.
The patch 4 adds driver to support PLL clocks for JH7110.
The patch 5 modifies the system clock driver and can select the PLL clock
source from PLL clocks driver. And the patch 6 adds the
stg/sys/aon syscon nodes for JH7110 SoC. The last patch modifies the
syscrg node in JH7110 dts file.
Changes since v6:
- Rebased on Linux 6.5-rc2.
- Patch 1 added the 'the' in front of 'JH7110' and changed the PLL clock
names from 'JH7110_CLK_PLL?_OUT' to 'JH7110_PLLCLK_PLL?_OUT' in the
binding of PLL.
- Patch 2 modified the value of 'reg' in example to fix the error.
- Patch 4 and 7 changed the PLL clock names from 'JH7110_CLK_PLL?_OUT'
to 'JH7110_PLLCLK_PLL?_OUT' in the driver and dts.
- Patch 5 added clk_put() and a better way to detect if the pll
references are specified in the device tree or not.
v6: https://lore.kernel.org/all/20230704064610.292603-1-xingyu.wu@starfivetech.com/
Changes since v5:
- Rebased on Linux 6.4.
- Patch 1 fixed some grammatical mistake.
- Patch 2 added the selection about properties from different syscon
modules and madethe example completed.
- Patch 3 dropped the 'optional' PLL clocks.
v5: https://lore.kernel.org/all/20230613125852.211636-1-xingyu.wu@starfivetech.com/
Changes since v4:
- Rebased on Linux 6.4-rc6.
- Patch 2 dropped the example node about sys-syscon.
- Patch 3 used PLL clocks as one of optional items in SYSCRG bindings.
- Patch 4 used the patch instead about PLL clocks driver from Emil.
- Patch 5 retained the fixed factor PLL clocks as the optional source
about PLL clocks in SYSCRG clock driver.
- Patch 6 added the child node clock-controller as the complete
sys-syscon node and patch 7 dropped this part.
v4: https://lore.kernel.org/all/20230512022036.97987-1-xingyu.wu@starfivetech.com/
Changes since v3:
- Rebased on Linux 6.4-rc1.
- Dropped the 'power-controller' property and used 'power-domain-cells'
instead in syscon binding.
- Used the data by of_device_id to get the syscon registers'
configuration include offset, mask and shift.
v3: https://lore.kernel.org/all/20230414024157.53203-1-xingyu.wu@starfivetech.com/
Changes since v2:
- Rebased on latest JH7110 basic clock drivers.
- Added the complete documentation to describe syscon register.
- Added syscon node in JH7110 dts file.
- Modified the clock rate selection to match the closest rate in
PLL driver when setting rate.
v2: https://lore.kernel.org/all/20230316030514.137427-1-xingyu.wu@starfivetech.com/
Changes since v1:
- Changed PLL clock node to be child of syscon node in dts.
- Modifed the definitions and names of function in PLL clock driver.
- Added commit to update syscon and syscrg dt-bindings.
v1: https://lore.kernel.org/all/20230221141147.303642-1-xingyu.wu@starfivetech.com/
William Qiu (2):
dt-bindings: soc: starfive: Add StarFive syscon module
riscv: dts: starfive: jh7110: Add syscon nodes
Xingyu Wu (5):
dt-bindings: clock: Add StarFive JH7110 PLL clock generator
dt-bindings: clock: jh7110-syscrg: Add PLL clock inputs
clk: starfive: Add StarFive JH7110 PLL clock driver
clk: starfive: jh7110-sys: Add PLL clocks source from DTS
riscv: dts: starfive: jh7110: Add PLL clocks source in SYSCRG node
.../bindings/clock/starfive,jh7110-pll.yaml | 46 ++
.../clock/starfive,jh7110-syscrg.yaml | 18 +-
.../soc/starfive/starfive,jh7110-syscon.yaml | 93 ++++
MAINTAINERS | 13 +
arch/riscv/boot/dts/starfive/jh7110.dtsi | 30 +-
drivers/clk/starfive/Kconfig | 9 +
drivers/clk/starfive/Makefile | 1 +
.../clk/starfive/clk-starfive-jh7110-pll.c | 507 ++++++++++++++++++
.../clk/starfive/clk-starfive-jh7110-sys.c | 66 ++-
.../dt-bindings/clock/starfive,jh7110-crg.h | 6 +
10 files changed, 763 insertions(+), 26 deletions(-)
create mode 100644 Documentation/devicetree/bindings/clock/starfive,jh7110-pll.yaml
create mode 100644 Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-syscon.yaml
create mode 100644 drivers/clk/starfive/clk-starfive-jh7110-pll.c
--
2.25.1
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv
next reply other threads:[~2023-07-17 2:31 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-07-17 2:30 Xingyu Wu [this message]
2023-07-17 2:30 ` [PATCH v7 1/7] dt-bindings: clock: Add StarFive JH7110 PLL clock generator Xingyu Wu
2023-07-19 15:45 ` Emil Renner Berthing
2023-07-17 2:30 ` [PATCH v7 2/7] dt-bindings: soc: starfive: Add StarFive syscon module Xingyu Wu
2023-07-17 2:30 ` [PATCH v7 3/7] dt-bindings: clock: jh7110-syscrg: Add PLL clock inputs Xingyu Wu
2023-07-17 2:30 ` [PATCH v7 4/7] clk: starfive: Add StarFive JH7110 PLL clock driver Xingyu Wu
2023-07-17 2:30 ` [PATCH v7 5/7] clk: starfive: jh7110-sys: Add PLL clocks source from DTS Xingyu Wu
2023-07-19 15:49 ` Emil Renner Berthing
2023-07-17 2:30 ` [PATCH v7 6/7] riscv: dts: starfive: jh7110: Add syscon nodes Xingyu Wu
2023-07-17 2:30 ` [PATCH v7 7/7] riscv: dts: starfive: jh7110: Add PLL clocks source in SYSCRG node Xingyu Wu
2023-07-17 18:14 ` [PATCH v7 0/7] Add PLL clocks driver and syscon for StarFive JH7110 SoC Conor Dooley
2023-07-18 5:48 ` Xingyu Wu
2023-07-20 16:29 ` (subset) " Conor Dooley
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230717023040.78860-1-xingyu.wu@starfivetech.com \
--to=xingyu.wu@starfivetech.com \
--cc=aou@eecs.berkeley.edu \
--cc=conor@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=emil.renner.berthing@canonical.com \
--cc=hal.feng@starfivetech.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-riscv@lists.infradead.org \
--cc=mturquette@baylibre.com \
--cc=p.zabel@pengutronix.de \
--cc=palmer@dabbelt.com \
--cc=paul.walmsley@sifive.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
--cc=william.qiu@starfivetech.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).