From: Ansuel Smith <ansuelsmth@gmail.com>
To: Thara Gopinath <thara.gopinath@linaro.org>
Cc: Ansuel Smith <ansuelsmth@gmail.com>,
Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Amit Kucheria <amitk@kernel.org>, Zhang Rui <rui.zhang@intel.com>,
Daniel Lezcano <daniel.lezcano@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
linux-arm-msm@vger.kernel.org, linux-pm@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: [PATCH v11 5/9] drivers: thermal: tsens: Fix bug in sensor enable for msm8960
Date: Fri, 19 Mar 2021 01:52:23 +0100 [thread overview]
Message-ID: <20210319005228.1250-6-ansuelsmth@gmail.com> (raw)
In-Reply-To: <20210319005228.1250-1-ansuelsmth@gmail.com>
Device based on tsens VER_0 contains a hardware bug that results in some
problem with sensor enablement. Sensor id 6-11 can't be enabled
selectively and all of them must be enabled in one step.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
---
drivers/thermal/qcom/tsens-8960.c | 24 +++++++++++++++++++++---
1 file changed, 21 insertions(+), 3 deletions(-)
diff --git a/drivers/thermal/qcom/tsens-8960.c b/drivers/thermal/qcom/tsens-8960.c
index 86585f439985..bdc64d4188bf 100644
--- a/drivers/thermal/qcom/tsens-8960.c
+++ b/drivers/thermal/qcom/tsens-8960.c
@@ -27,9 +27,9 @@
#define EN BIT(0)
#define SW_RST BIT(1)
#define SENSOR0_EN BIT(3)
+#define MEASURE_PERIOD BIT(18)
#define SLP_CLK_ENA BIT(26)
#define SLP_CLK_ENA_8660 BIT(24)
-#define MEASURE_PERIOD 1
#define SENSOR0_SHIFT 3
/* INT_STATUS_ADDR bitmasks */
@@ -126,17 +126,35 @@ static int resume_8960(struct tsens_priv *priv)
static int enable_8960(struct tsens_priv *priv, int id)
{
int ret;
- u32 reg, mask;
+ u32 reg, mask = BIT(id);
ret = regmap_read(priv->tm_map, CNTL_ADDR, ®);
if (ret)
return ret;
- mask = BIT(id + SENSOR0_SHIFT);
+ /* HARDWARE BUG:
+ * On platform with more than 6 sensors, all the remaining
+ * sensors needs to be enabled all togheder or underfined
+ * results are expected. (Sensor 6-7 disabled, Sensor 3
+ * disabled...) In the original driver, all the sensors
+ * are enabled in one step hence this bug is not triggered.
+ */
+ if (id > 5) {
+ mask = GENMASK(10, 6);
+
+ /* Sensors already enabled. Skip. */
+ if ((reg & mask) == mask)
+ return 0;
+ }
+
+ mask <<= SENSOR0_SHIFT;
+
ret = regmap_write(priv->tm_map, CNTL_ADDR, reg | SW_RST);
if (ret)
return ret;
+ reg |= MEASURE_PERIOD;
+
if (priv->num_sensors > 1)
reg |= mask | SLP_CLK_ENA | EN;
else
--
2.30.2
next prev parent reply other threads:[~2021-03-19 0:53 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-03-19 0:52 [PATCH v11 0/9] Add support for ipq8064 tsens Ansuel Smith
2021-03-19 0:52 ` [PATCH v11 1/9] drivers: thermal: tsens: Add VER_0 tsens version Ansuel Smith
2021-03-19 13:11 ` Thara Gopinath
2021-03-19 13:28 ` Ansuel Smith
2021-03-19 14:11 ` Thara Gopinath
2021-03-19 0:52 ` [PATCH v11 2/9] drivers: thermal: tsens: Don't hardcode sensor slope Ansuel Smith
2021-03-19 0:52 ` [PATCH v11 3/9] drivers: thermal: tsens: Convert msm8960 to reg_field Ansuel Smith
2021-03-19 0:52 ` [PATCH v11 4/9] drivers: thermal: tsens: Use init_common for msm8960 Ansuel Smith
2021-03-19 0:52 ` Ansuel Smith [this message]
2021-03-19 13:11 ` [PATCH v11 5/9] drivers: thermal: tsens: Fix bug in sensor enable " Thara Gopinath
2021-03-22 10:47 ` Marc Gonzalez
2021-03-19 0:52 ` [PATCH v11 6/9] drivers: thermal: tsens: Replace custom 8960 apis with generic apis Ansuel Smith
2021-03-19 13:12 ` Thara Gopinath
2021-03-19 0:52 ` [PATCH v11 7/9] drivers: thermal: tsens: Drop unused define for msm8960 Ansuel Smith
2021-03-19 13:12 ` Thara Gopinath
2021-03-19 0:52 ` [PATCH v11 8/9] drivers: thermal: tsens: Add support for ipq8064-tsens Ansuel Smith
2021-03-19 0:52 ` [PATCH v11 9/9] dt-bindings: thermal: tsens: Document ipq8064 bindings Ansuel Smith
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210319005228.1250-6-ansuelsmth@gmail.com \
--to=ansuelsmth@gmail.com \
--cc=agross@kernel.org \
--cc=amitk@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=daniel.lezcano@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=rui.zhang@intel.com \
--cc=thara.gopinath@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).