* [PATCH v3 1/2] macb: bindings doc: add sifive fu540-c000 binding
2019-06-18 7:56 [PATCH v3 0/2] Add macb support for SiFive FU540-C000 Yash Shah
@ 2019-06-18 7:56 ` Yash Shah
2019-06-18 7:56 ` [PATCH v3 2/2] macb: Add support for SiFive FU540-C000 Yash Shah
` (2 subsequent siblings)
3 siblings, 0 replies; 5+ messages in thread
From: Yash Shah @ 2019-06-18 7:56 UTC (permalink / raw)
To: davem, devicetree, netdev, linux-kernel, linux-riscv
Cc: robh+dt, mark.rutland, nicolas.ferre, palmer, aou, paul.walmsley,
ynezz, sachin.ghadi, Yash Shah
Add the compatibility string documentation for SiFive FU540-C0000
interface.
On the FU540, this driver also needs to read and write registers in a
management IP block that monitors or drives boundary signals for the
GEMGXL IP block that are not directly mapped to GEMGXL registers.
Therefore, add additional range to "reg" property for SiFive GEMGXL
management IP registers.
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
---
Documentation/devicetree/bindings/net/macb.txt | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt
index 9c5e944..63c73fa 100644
--- a/Documentation/devicetree/bindings/net/macb.txt
+++ b/Documentation/devicetree/bindings/net/macb.txt
@@ -15,8 +15,11 @@ Required properties:
Use "atmel,sama5d4-gem" for the GEM IP (10/100) available on Atmel sama5d4 SoCs.
Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC.
Use "cdns,zynqmp-gem" for Zynq Ultrascale+ MPSoC.
+ Use "sifive,fu540-macb" for SiFive FU540-C000 SoC.
Or the generic form: "cdns,emac".
- reg: Address and length of the register set for the device
+ For "sifive,fu540-macb", second range is required to specify the
+ address and length of the registers for GEMGXL Management block.
- interrupts: Should contain macb interrupt
- phy-mode: See ethernet.txt file in the same directory.
- clock-names: Tuple listing input clock names.
--
1.9.1
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH v3 2/2] macb: Add support for SiFive FU540-C000
2019-06-18 7:56 [PATCH v3 0/2] Add macb support for SiFive FU540-C000 Yash Shah
2019-06-18 7:56 ` [PATCH v3 1/2] macb: bindings doc: add sifive fu540-c000 binding Yash Shah
@ 2019-06-18 7:56 ` Yash Shah
2019-06-18 23:27 ` [PATCH v3 0/2] Add macb " Atish Patra
2019-06-19 2:02 ` David Miller
3 siblings, 0 replies; 5+ messages in thread
From: Yash Shah @ 2019-06-18 7:56 UTC (permalink / raw)
To: davem, devicetree, netdev, linux-kernel, linux-riscv
Cc: robh+dt, mark.rutland, nicolas.ferre, palmer, aou, paul.walmsley,
ynezz, sachin.ghadi, Yash Shah
The management IP block is tightly coupled with the Cadence MACB IP
block on the FU540, and manages many of the boundary signals from the
MACB IP. This patch only controls the tx_clk input signal to the MACB
IP. Future patches may add support for monitoring or controlling other
IP boundary signals.
Signed-off-by: Yash Shah <yash.shah@sifive.com>
---
drivers/net/ethernet/cadence/macb_main.c | 123 +++++++++++++++++++++++++++++++
1 file changed, 123 insertions(+)
diff --git a/drivers/net/ethernet/cadence/macb_main.c b/drivers/net/ethernet/cadence/macb_main.c
index c049410..15d0737 100644
--- a/drivers/net/ethernet/cadence/macb_main.c
+++ b/drivers/net/ethernet/cadence/macb_main.c
@@ -10,6 +10,7 @@
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
#include <linux/clk.h>
+#include <linux/clk-provider.h>
#include <linux/crc32.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
@@ -40,6 +41,15 @@
#include <linux/pm_runtime.h>
#include "macb.h"
+/* This structure is only used for MACB on SiFive FU540 devices */
+struct sifive_fu540_macb_mgmt {
+ void __iomem *reg;
+ unsigned long rate;
+ struct clk_hw hw;
+};
+
+static struct sifive_fu540_macb_mgmt *mgmt;
+
#define MACB_RX_BUFFER_SIZE 128
#define RX_BUFFER_MULTIPLE 64 /* bytes */
@@ -3903,6 +3913,116 @@ static int at91ether_init(struct platform_device *pdev)
return 0;
}
+static unsigned long fu540_macb_tx_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ return mgmt->rate;
+}
+
+static long fu540_macb_tx_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *parent_rate)
+{
+ if (WARN_ON(rate < 2500000))
+ return 2500000;
+ else if (rate == 2500000)
+ return 2500000;
+ else if (WARN_ON(rate < 13750000))
+ return 2500000;
+ else if (WARN_ON(rate < 25000000))
+ return 25000000;
+ else if (rate == 25000000)
+ return 25000000;
+ else if (WARN_ON(rate < 75000000))
+ return 25000000;
+ else if (WARN_ON(rate < 125000000))
+ return 125000000;
+ else if (rate == 125000000)
+ return 125000000;
+
+ WARN_ON(rate > 125000000);
+
+ return 125000000;
+}
+
+static int fu540_macb_tx_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ rate = fu540_macb_tx_round_rate(hw, rate, &parent_rate);
+ if (rate != 125000000)
+ iowrite32(1, mgmt->reg);
+ else
+ iowrite32(0, mgmt->reg);
+ mgmt->rate = rate;
+
+ return 0;
+}
+
+static const struct clk_ops fu540_c000_ops = {
+ .recalc_rate = fu540_macb_tx_recalc_rate,
+ .round_rate = fu540_macb_tx_round_rate,
+ .set_rate = fu540_macb_tx_set_rate,
+};
+
+static int fu540_c000_clk_init(struct platform_device *pdev, struct clk **pclk,
+ struct clk **hclk, struct clk **tx_clk,
+ struct clk **rx_clk, struct clk **tsu_clk)
+{
+ struct clk_init_data init;
+ int err = 0;
+
+ err = macb_clk_init(pdev, pclk, hclk, tx_clk, rx_clk, tsu_clk);
+ if (err)
+ return err;
+
+ mgmt = devm_kzalloc(&pdev->dev, sizeof(*mgmt), GFP_KERNEL);
+ if (!mgmt)
+ return -ENOMEM;
+
+ init.name = "sifive-gemgxl-mgmt";
+ init.ops = &fu540_c000_ops;
+ init.flags = 0;
+ init.num_parents = 0;
+
+ mgmt->rate = 0;
+ mgmt->hw.init = &init;
+
+ *tx_clk = clk_register(NULL, &mgmt->hw);
+ if (IS_ERR(*tx_clk))
+ return PTR_ERR(*tx_clk);
+
+ err = clk_prepare_enable(*tx_clk);
+ if (err)
+ dev_err(&pdev->dev, "failed to enable tx_clk (%u)\n", err);
+ else
+ dev_info(&pdev->dev, "Registered clk switch '%s'\n", init.name);
+
+ return 0;
+}
+
+static int fu540_c000_init(struct platform_device *pdev)
+{
+ struct resource *res;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ if (!res)
+ return -ENODEV;
+
+ mgmt->reg = ioremap(res->start, resource_size(res));
+ if (!mgmt->reg)
+ return -ENOMEM;
+
+ return macb_init(pdev);
+}
+
+static const struct macb_config fu540_c000_config = {
+ .caps = MACB_CAPS_GIGABIT_MODE_AVAILABLE | MACB_CAPS_JUMBO |
+ MACB_CAPS_GEM_HAS_PTP,
+ .dma_burst_length = 16,
+ .clk_init = fu540_c000_clk_init,
+ .init = fu540_c000_init,
+ .jumbo_max_len = 10240,
+};
+
static const struct macb_config at91sam9260_config = {
.caps = MACB_CAPS_USRIO_HAS_CLKEN | MACB_CAPS_USRIO_DEFAULT_IS_MII_GMII,
.clk_init = macb_clk_init,
@@ -3992,6 +4112,7 @@ static int at91ether_init(struct platform_device *pdev)
{ .compatible = "cdns,emac", .data = &emac_config },
{ .compatible = "cdns,zynqmp-gem", .data = &zynqmp_config},
{ .compatible = "cdns,zynq-gem", .data = &zynq_config },
+ { .compatible = "sifive,fu540-macb", .data = &fu540_c000_config },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, macb_dt_ids);
@@ -4199,6 +4320,7 @@ static int macb_probe(struct platform_device *pdev)
err_disable_clocks:
clk_disable_unprepare(tx_clk);
+ clk_unregister(tx_clk);
clk_disable_unprepare(hclk);
clk_disable_unprepare(pclk);
clk_disable_unprepare(rx_clk);
@@ -4233,6 +4355,7 @@ static int macb_remove(struct platform_device *pdev)
pm_runtime_dont_use_autosuspend(&pdev->dev);
if (!pm_runtime_suspended(&pdev->dev)) {
clk_disable_unprepare(bp->tx_clk);
+ clk_unregister(bp->tx_clk);
clk_disable_unprepare(bp->hclk);
clk_disable_unprepare(bp->pclk);
clk_disable_unprepare(bp->rx_clk);
--
1.9.1
^ permalink raw reply related [flat|nested] 5+ messages in thread* Re: [PATCH v3 0/2] Add macb support for SiFive FU540-C000
2019-06-18 7:56 [PATCH v3 0/2] Add macb support for SiFive FU540-C000 Yash Shah
2019-06-18 7:56 ` [PATCH v3 1/2] macb: bindings doc: add sifive fu540-c000 binding Yash Shah
2019-06-18 7:56 ` [PATCH v3 2/2] macb: Add support for SiFive FU540-C000 Yash Shah
@ 2019-06-18 23:27 ` Atish Patra
2019-06-19 2:02 ` David Miller
3 siblings, 0 replies; 5+ messages in thread
From: Atish Patra @ 2019-06-18 23:27 UTC (permalink / raw)
To: linux-riscv, linux-kernel, devicetree, davem, yash.shah, netdev
Cc: sachin.ghadi, nicolas.ferre, mark.rutland, paul.walmsley, aou,
ynezz, palmer, robh+dt
On Tue, 2019-06-18 at 13:26 +0530, Yash Shah wrote:
> On FU540, the management IP block is tightly coupled with the Cadence
> MACB IP block. It manages many of the boundary signals from the MACB
> IP
> This patchset controls the tx_clk input signal to the MACB IP. It
> switches between the local TX clock (125MHz) and PHY TX clocks. This
> is necessary to toggle between 1Gb and 100/10Mb speeds.
>
> Future patches may add support for monitoring or controlling other IP
> boundary signals.
>
> This patchset is mostly based on work done by
> Wesley Terpstra <wesley@sifive.com>
>
> This patchset is based on Linux v5.2-rc1 and tested on HiFive
> Unleashed
> board with additional board related patches needed for testing can be
> found at dev/yashs/ethernet_v3 branch of:
> https://github.com/yashshah7/riscv-linux.git
>
> Change History:
> V3:
> - Revert "MACB_SIFIVE_FU540" config changes in Kconfig and driver
> code.
> The driver does not depend on SiFive GPIO driver.
>
> V2:
> - Change compatible string from "cdns,fu540-macb" to "sifive,fu540-
> macb"
> - Add "MACB_SIFIVE_FU540" in Kconfig to support SiFive FU540 in macb
> driver. This is needed because on FU540, the macb driver depends on
> SiFive GPIO driver.
> - Avoid writing the result of a comparison to a register.
> - Fix the issue of probe fail on reloading the module reported by:
> Andreas Schwab <schwab@suse.de>
>
> Yash Shah (2):
> macb: bindings doc: add sifive fu540-c000 binding
> macb: Add support for SiFive FU540-C000
>
> Documentation/devicetree/bindings/net/macb.txt | 3 +
> drivers/net/ethernet/cadence/macb_main.c | 123
> +++++++++++++++++++++++++
> 2 files changed, 126 insertions(+)
>
Can you also post the ethernet dt entry[1] along with this patch ?
I think it would be good to all the dt related stuff reviewed together.
[1]
https://github.com/yashshah7/riscv-linux/commit/6d3af64bc5efed3915d658dc3bfe82dc1dbfafb3
I am able to get networking up in latest kernel + your patches in
OpenSBI + U-Boot(with updated compatible string) + Linux bootflow.
Tested-by: Atish Patra <atish.patra@wdc.com>
Regards,
Atish
^ permalink raw reply [flat|nested] 5+ messages in thread