From: Matthew Barth <msbarth@linux.ibm.com>
To: Eddie James <eajames@linux.ibm.com>, openbmc@lists.ozlabs.org
Subject: Re: [PATCH linux dev-5.10 08/14] ARM: dts: aspeed: Rainier: Add fan controller properties
Date: Wed, 11 Aug 2021 11:14:34 -0500 [thread overview]
Message-ID: <c24ea0f7-0f83-a4b9-d019-cc0e3847e8a0@linux.ibm.com> (raw)
In-Reply-To: <20210811154232.12649-9-eajames@linux.ibm.com>
On 8/11/21 10:42 AM, Eddie James wrote:
> Add the necessary Max chip specific fan properties.
>
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Matthew Barth <msbarth@linux.ibm.com>
> ---
> arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts | 42 ++++++++++++++++++++
> 1 file changed, 42 insertions(+)
>
> diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
> index f87bc5dc8aba..6fd3ddf97a21 100644
> --- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
> +++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
> @@ -1282,36 +1282,78 @@ fan0: fan@0 {
> compatible = "pmbus-fan";
> reg = <0>;
> tach-pulses = <2>;
> + maxim,fan-rotor-input = "tach";
> + maxim,fan-pwm-freq = <25000>;
> + maxim,fan-dual-tach;
> + maxim,fan-no-watchdog;
> + maxim,fan-no-fault-ramp;
> + maxim,fan-ramp = <2>;
> + maxim,fan-fault-pin-mon;
> };
>
> fan1: fan@1 {
> compatible = "pmbus-fan";
> reg = <1>;
> tach-pulses = <2>;
> + maxim,fan-rotor-input = "tach";
> + maxim,fan-pwm-freq = <25000>;
> + maxim,fan-dual-tach;
> + maxim,fan-no-watchdog;
> + maxim,fan-no-fault-ramp;
> + maxim,fan-ramp = <2>;
> + maxim,fan-fault-pin-mon;
> };
>
> fan2: fan@2 {
> compatible = "pmbus-fan";
> reg = <2>;
> tach-pulses = <2>;
> + maxim,fan-rotor-input = "tach";
> + maxim,fan-pwm-freq = <25000>;
> + maxim,fan-dual-tach;
> + maxim,fan-no-watchdog;
> + maxim,fan-no-fault-ramp;
> + maxim,fan-ramp = <2>;
> + maxim,fan-fault-pin-mon;
> };
>
> fan3: fan@3 {
> compatible = "pmbus-fan";
> reg = <3>;
> tach-pulses = <2>;
> + maxim,fan-rotor-input = "tach";
> + maxim,fan-pwm-freq = <25000>;
> + maxim,fan-dual-tach;
> + maxim,fan-no-watchdog;
> + maxim,fan-no-fault-ramp;
> + maxim,fan-ramp = <2>;
> + maxim,fan-fault-pin-mon;
> };
>
> fan4: fan@4 {
> compatible = "pmbus-fan";
> reg = <4>;
> tach-pulses = <2>;
> + maxim,fan-rotor-input = "tach";
> + maxim,fan-pwm-freq = <25000>;
> + maxim,fan-dual-tach;
> + maxim,fan-no-watchdog;
> + maxim,fan-no-fault-ramp;
> + maxim,fan-ramp = <2>;
> + maxim,fan-fault-pin-mon;
> };
>
> fan5: fan@5 {
> compatible = "pmbus-fan";
> reg = <5>;
> tach-pulses = <2>;
> + maxim,fan-rotor-input = "tach";
> + maxim,fan-pwm-freq = <25000>;
> + maxim,fan-dual-tach;
> + maxim,fan-no-watchdog;
> + maxim,fan-no-fault-ramp;
> + maxim,fan-ramp = <2>;
> + maxim,fan-fault-pin-mon;
> };
> };
>
next prev parent reply other threads:[~2021-08-11 16:44 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-08-11 15:42 [PATCH linux dev-5.10 00/14] Rainier and Everest system fixes Eddie James
2021-08-11 15:42 ` [PATCH linux dev-5.10 01/14] i2c: Allow throttling of transfers to client devices Eddie James
2021-08-11 15:42 ` [PATCH linux dev-5.10 02/14] pmbus: (ucd9000) Throttle SMBus transfers to avoid poor behaviour Eddie James
2021-08-11 15:42 ` [PATCH linux dev-5.10 03/14] ucd9000: Add a throttle delay attribute in debugfs Eddie James
2021-08-11 15:42 ` [PATCH linux dev-5.10 04/14] fsi: run clock at 100MHz Eddie James
2021-08-11 15:42 ` [PATCH linux dev-5.10 05/14] pmbus: (core) Add a one-shot retry in pmbus_set_page() Eddie James
2021-08-11 15:42 ` [PATCH linux dev-5.10 06/14] pmbus: (max31785) Add a local pmbus_set_page() implementation Eddie James
2021-08-11 16:13 ` Matthew Barth
2021-08-11 15:42 ` [PATCH linux dev-5.10 07/14] pmbus: (max31785) Retry enabling fans after writing MFR_FAN_CONFIG Eddie James
2021-08-11 16:14 ` Matthew Barth
2021-08-11 15:42 ` [PATCH linux dev-5.10 08/14] ARM: dts: aspeed: Rainier: Add fan controller properties Eddie James
2021-08-11 16:14 ` Matthew Barth [this message]
2021-08-11 15:42 ` [PATCH linux dev-5.10 09/14] ARM: dts: aspeed: Everest: " Eddie James
2021-08-11 16:15 ` Matthew Barth
2021-08-11 15:42 ` [PATCH linux dev-5.10 10/14] ARM: dts: aspeed: Rainier 4U: Delete fan dual-tach properties Eddie James
2021-08-11 16:17 ` Matthew Barth
2021-08-11 15:42 ` [PATCH linux dev-5.10 11/14] ARM: dts: aspeed: Add Rainier 2U and 4U device trees for pass 1 hardware Eddie James
2021-08-11 15:42 ` [PATCH linux dev-5.10 12/14] fsi: sbefifo: Increase command timeouts to 30 seconds Eddie James
2021-08-11 15:42 ` [PATCH linux dev-5.10 13/14] fsi: occ: Add dynamic debug to dump command and response Eddie James
2021-08-11 15:42 ` [PATCH linux dev-5.10 14/14] fsi: sbefifo: Use interruptible mutex locking Eddie James
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=c24ea0f7-0f83-a4b9-d019-cc0e3847e8a0@linux.ibm.com \
--to=msbarth@linux.ibm.com \
--cc=eajames@linux.ibm.com \
--cc=openbmc@lists.ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).