From: Krzysztof Kozlowski <k.kozlowski.k@gmail.com> To: Kukjin Kim <kgene@kernel.org>, devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org, linux-samsung-soc@vger.kernel.org, linux-kernel@vger.kernel.org Cc: Krzysztof Kozlowski <k.kozlowski.k@gmail.com> Subject: [PATCH v6 05/13] ARM: dts: Use labels for overriding nodes in exynos4210-trats Date: Sun, 17 May 2015 17:09:51 +0900 [thread overview] Message-ID: <1431850195-9558-10-git-send-email-k.kozlowski.k@gmail.com> (raw) In-Reply-To: <1431850195-9558-1-git-send-email-k.kozlowski.k@gmail.com> Usage of labels instead of full paths reduces possible mistakes when overriding nodes. Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com> --- arch/arm/boot/dts/exynos4210-trats.dts | 592 ++++++++++++++++----------------- 1 file changed, 296 insertions(+), 296 deletions(-) diff --git a/arch/arm/boot/dts/exynos4210-trats.dts b/arch/arm/boot/dts/exynos4210-trats.dts index 32c5fd8f6269..98f3ce65cb9a 100644 --- a/arch/arm/boot/dts/exynos4210-trats.dts +++ b/arch/arm/boot/dts/exynos4210-trats.dts @@ -89,42 +89,6 @@ }; }; - hsotg@12480000 { - vusb_d-supply = <&vusb_reg>; - vusb_a-supply = <&vusbdac_reg>; - dr_mode = "peripheral"; - status = "okay"; - }; - - sdhci_emmc: sdhci@12510000 { - bus-width = <8>; - non-removable; - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>; - pinctrl-names = "default"; - vmmc-supply = <&vemmc_reg>; - status = "okay"; - }; - - exynos-usbphy@125B0000 { - status = "okay"; - }; - - serial@13800000 { - status = "okay"; - }; - - serial@13810000 { - status = "okay"; - }; - - serial@13820000 { - status = "okay"; - }; - - serial@13830000 { - status = "okay"; - }; - gpio-keys { compatible = "gpio-keys"; @@ -158,201 +122,6 @@ }; }; - i2c@13890000 { - samsung,i2c-sda-delay = <100>; - samsung,i2c-slave-addr = <0x10>; - samsung,i2c-max-bus-freq = <400000>; - pinctrl-0 = <&i2c3_bus>; - pinctrl-names = "default"; - status = "okay"; - - mms114-touchscreen@48 { - compatible = "melfas,mms114"; - reg = <0x48>; - interrupt-parent = <&gpx0>; - interrupts = <4 2>; - x-size = <720>; - y-size = <1280>; - avdd-supply = <&tsp_reg>; - vdd-supply = <&tsp_reg>; - }; - }; - - i2c@138B0000 { - samsung,i2c-sda-delay = <100>; - samsung,i2c-slave-addr = <0x10>; - samsung,i2c-max-bus-freq = <100000>; - pinctrl-0 = <&i2c5_bus>; - pinctrl-names = "default"; - status = "okay"; - - max8997_pmic@66 { - compatible = "maxim,max8997-pmic"; - - reg = <0x66>; - - max8997,pmic-buck1-uses-gpio-dvs; - max8997,pmic-buck2-uses-gpio-dvs; - max8997,pmic-buck5-uses-gpio-dvs; - - max8997,pmic-ignore-gpiodvs-side-effect; - max8997,pmic-buck125-default-dvs-idx = <0>; - - max8997,pmic-buck125-dvs-gpios = <&gpx0 5 0>, - <&gpx0 6 0>, - <&gpl0 0 0>; - - max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>, - <1250000>, <1200000>, - <1150000>, <1100000>, - <1000000>, <950000>; - - max8997,pmic-buck2-dvs-voltage = <1100000>, <1000000>, - <950000>, <900000>, - <1100000>, <1000000>, - <950000>, <900000>; - - max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>, - <1200000>, <1200000>, - <1200000>, <1200000>, - <1200000>, <1200000>; - - regulators { - valive_reg: LDO2 { - regulator-name = "VALIVE_1.1V_C210"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - regulator-always-on; - }; - - vusb_reg: LDO3 { - regulator-name = "VUSB_1.1V_C210"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - }; - - vmipi_reg: LDO4 { - regulator-name = "VMIPI_1.8V"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - }; - - vpda_reg: LDO6 { - regulator-name = "VCC_1.8V_PDA"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - vcam_reg: LDO7 { - regulator-name = "CAM_ISP_1.8V"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - }; - - vusbdac_reg: LDO8 { - regulator-name = "VUSB/VDAC_3.3V_C210"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - vccpda_reg: LDO9 { - regulator-name = "VCC_2.8V_PDA"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - regulator-always-on; - }; - - vpll_reg: LDO10 { - regulator-name = "VPLL_1.1V_C210"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - regulator-always-on; - }; - - vtcam_reg: LDO12 { - regulator-name = "VT_CAM_1.8V"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - }; - - vcclcd_reg: LDO13 { - regulator-name = "VCC_3.3V_LCD"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - vlcd_reg: LDO15 { - regulator-name = "VLCD_2.2V"; - regulator-min-microvolt = <2200000>; - regulator-max-microvolt = <2200000>; - }; - - camsensor_reg: LDO16 { - regulator-name = "CAM_SENSOR_IO_1.8V"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - }; - - vddq_reg: LDO21 { - regulator-name = "VDDQ_M1M2_1.2V"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-always-on; - }; - - varm_breg: BUCK1 { - /* - * HACK: The real name is VARM_1.2V_C210, - * but exynos-cpufreq does not support - * DT-based regulator lookup yet. - */ - regulator-name = "vdd_arm"; - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - }; - - vint_breg: BUCK2 { - regulator-name = "VINT_1.1V_C210"; - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <1100000>; - regulator-always-on; - }; - - camisp_breg: BUCK4 { - regulator-name = "CAM_ISP_CORE_1.2V"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - }; - - vmem_breg: BUCK5 { - regulator-name = "VMEM_1.2V_C210"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-always-on; - }; - - vccsub_breg: BUCK7 { - regulator-name = "VCC_SUB_2.0V"; - regulator-min-microvolt = <2000000>; - regulator-max-microvolt = <2000000>; - regulator-always-on; - }; - - safe1_sreg: ESAFEOUT1 { - regulator-name = "SAFEOUT1"; - regulator-always-on; - }; - - safe2_sreg: ESAFEOUT2 { - regulator-name = "SAFEOUT2"; - regulator-boot-on; - }; - }; - }; - }; - fixed-rate-clocks { xxti { compatible = "samsung,clock-xxti"; @@ -365,71 +134,6 @@ }; }; - dsi_0: dsi@11C80000 { - vddcore-supply = <&vusb_reg>; - vddio-supply = <&vmipi_reg>; - samsung,pll-clock-frequency = <24000000>; - status = "okay"; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@1 { - reg = <1>; - - dsi_out: endpoint { - remote-endpoint = <&dsi_in>; - samsung,burst-clock-frequency = <500000000>; - samsung,esc-clock-frequency = <20000000>; - }; - }; - }; - - panel@0 { - reg = <0>; - compatible = "samsung,s6e8aa0"; - vdd3-supply = <&vcclcd_reg>; - vci-supply = <&vlcd_reg>; - reset-gpios = <&gpy4 5 0>; - power-on-delay= <50>; - reset-delay = <100>; - init-delay = <100>; - flip-horizontal; - flip-vertical; - panel-width-mm = <58>; - panel-height-mm = <103>; - - display-timings { - timing-0 { - clock-frequency = <57153600>; - hactive = <720>; - vactive = <1280>; - hfront-porch = <5>; - hback-porch = <5>; - hsync-len = <5>; - vfront-porch = <13>; - vback-porch = <1>; - vsync-len = <2>; - }; - }; - - port { - dsi_in: endpoint { - remote-endpoint = <&dsi_out>; - }; - }; - }; - }; - - fimd@11c00000 { - status = "okay"; - }; - - tmu@100C0000 { - status = "okay"; - }; - thermal-zones { cpu_thermal: cpu-thermal { cooling-maps { @@ -483,3 +187,299 @@ }; }; }; + +&dsi_0 { + vddcore-supply = <&vusb_reg>; + vddio-supply = <&vmipi_reg>; + samsung,pll-clock-frequency = <24000000>; + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + + dsi_out: endpoint { + remote-endpoint = <&dsi_in>; + samsung,burst-clock-frequency = <500000000>; + samsung,esc-clock-frequency = <20000000>; + }; + }; + }; + + panel@0 { + reg = <0>; + compatible = "samsung,s6e8aa0"; + vdd3-supply = <&vcclcd_reg>; + vci-supply = <&vlcd_reg>; + reset-gpios = <&gpy4 5 0>; + power-on-delay= <50>; + reset-delay = <100>; + init-delay = <100>; + flip-horizontal; + flip-vertical; + panel-width-mm = <58>; + panel-height-mm = <103>; + + display-timings { + timing-0 { + clock-frequency = <57153600>; + hactive = <720>; + vactive = <1280>; + hfront-porch = <5>; + hback-porch = <5>; + hsync-len = <5>; + vfront-porch = <13>; + vback-porch = <1>; + vsync-len = <2>; + }; + }; + + port { + dsi_in: endpoint { + remote-endpoint = <&dsi_out>; + }; + }; + }; +}; + +&exynos_usbphy { + status = "okay"; +}; + +&fimd { + status = "okay"; +}; + +&hsotg { + vusb_d-supply = <&vusb_reg>; + vusb_a-supply = <&vusbdac_reg>; + dr_mode = "peripheral"; + status = "okay"; +}; + +&i2c_3 { + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <400000>; + pinctrl-0 = <&i2c3_bus>; + pinctrl-names = "default"; + status = "okay"; + + mms114-touchscreen@48 { + compatible = "melfas,mms114"; + reg = <0x48>; + interrupt-parent = <&gpx0>; + interrupts = <4 2>; + x-size = <720>; + y-size = <1280>; + avdd-supply = <&tsp_reg>; + vdd-supply = <&tsp_reg>; + }; +}; + +&i2c_5 { + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <100000>; + pinctrl-0 = <&i2c5_bus>; + pinctrl-names = "default"; + status = "okay"; + + max8997_pmic@66 { + compatible = "maxim,max8997-pmic"; + + reg = <0x66>; + + max8997,pmic-buck1-uses-gpio-dvs; + max8997,pmic-buck2-uses-gpio-dvs; + max8997,pmic-buck5-uses-gpio-dvs; + + max8997,pmic-ignore-gpiodvs-side-effect; + max8997,pmic-buck125-default-dvs-idx = <0>; + + max8997,pmic-buck125-dvs-gpios = <&gpx0 5 0>, + <&gpx0 6 0>, + <&gpl0 0 0>; + + max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>, + <1250000>, <1200000>, + <1150000>, <1100000>, + <1000000>, <950000>; + + max8997,pmic-buck2-dvs-voltage = <1100000>, <1000000>, + <950000>, <900000>, + <1100000>, <1000000>, + <950000>, <900000>; + + max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>; + + regulators { + valive_reg: LDO2 { + regulator-name = "VALIVE_1.1V_C210"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + vusb_reg: LDO3 { + regulator-name = "VUSB_1.1V_C210"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + }; + + vmipi_reg: LDO4 { + regulator-name = "VMIPI_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vpda_reg: LDO6 { + regulator-name = "VCC_1.8V_PDA"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + vcam_reg: LDO7 { + regulator-name = "CAM_ISP_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vusbdac_reg: LDO8 { + regulator-name = "VUSB/VDAC_3.3V_C210"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vccpda_reg: LDO9 { + regulator-name = "VCC_2.8V_PDA"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; + + vpll_reg: LDO10 { + regulator-name = "VPLL_1.1V_C210"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + vtcam_reg: LDO12 { + regulator-name = "VT_CAM_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vcclcd_reg: LDO13 { + regulator-name = "VCC_3.3V_LCD"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vlcd_reg: LDO15 { + regulator-name = "VLCD_2.2V"; + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + }; + + camsensor_reg: LDO16 { + regulator-name = "CAM_SENSOR_IO_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vddq_reg: LDO21 { + regulator-name = "VDDQ_M1M2_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + varm_breg: BUCK1 { + /* + * HACK: The real name is VARM_1.2V_C210, + * but exynos-cpufreq does not support + * DT-based regulator lookup yet. + */ + regulator-name = "vdd_arm"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + vint_breg: BUCK2 { + regulator-name = "VINT_1.1V_C210"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + camisp_breg: BUCK4 { + regulator-name = "CAM_ISP_CORE_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + vmem_breg: BUCK5 { + regulator-name = "VMEM_1.2V_C210"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + vccsub_breg: BUCK7 { + regulator-name = "VCC_SUB_2.0V"; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + regulator-always-on; + }; + + safe1_sreg: ESAFEOUT1 { + regulator-name = "SAFEOUT1"; + regulator-always-on; + }; + + safe2_sreg: ESAFEOUT2 { + regulator-name = "SAFEOUT2"; + regulator-boot-on; + }; + }; + }; +}; + +&sdhci_0 { + bus-width = <8>; + non-removable; + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>; + pinctrl-names = "default"; + vmmc-supply = <&vemmc_reg>; + status = "okay"; +}; + +&serial_0 { + status = "okay"; +}; + +&serial_1 { + status = "okay"; +}; + +&serial_2 { + status = "okay"; +}; + +&serial_3 { + status = "okay"; +}; + +&tmu { + status = "okay"; +}; -- 2.1.4
WARNING: multiple messages have this Message-ID (diff)
From: k.kozlowski.k@gmail.com (Krzysztof Kozlowski) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH v6 05/13] ARM: dts: Use labels for overriding nodes in exynos4210-trats Date: Sun, 17 May 2015 17:09:51 +0900 [thread overview] Message-ID: <1431850195-9558-10-git-send-email-k.kozlowski.k@gmail.com> (raw) In-Reply-To: <1431850195-9558-1-git-send-email-k.kozlowski.k@gmail.com> Usage of labels instead of full paths reduces possible mistakes when overriding nodes. Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com> --- arch/arm/boot/dts/exynos4210-trats.dts | 592 ++++++++++++++++----------------- 1 file changed, 296 insertions(+), 296 deletions(-) diff --git a/arch/arm/boot/dts/exynos4210-trats.dts b/arch/arm/boot/dts/exynos4210-trats.dts index 32c5fd8f6269..98f3ce65cb9a 100644 --- a/arch/arm/boot/dts/exynos4210-trats.dts +++ b/arch/arm/boot/dts/exynos4210-trats.dts @@ -89,42 +89,6 @@ }; }; - hsotg at 12480000 { - vusb_d-supply = <&vusb_reg>; - vusb_a-supply = <&vusbdac_reg>; - dr_mode = "peripheral"; - status = "okay"; - }; - - sdhci_emmc: sdhci at 12510000 { - bus-width = <8>; - non-removable; - pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>; - pinctrl-names = "default"; - vmmc-supply = <&vemmc_reg>; - status = "okay"; - }; - - exynos-usbphy at 125B0000 { - status = "okay"; - }; - - serial at 13800000 { - status = "okay"; - }; - - serial at 13810000 { - status = "okay"; - }; - - serial at 13820000 { - status = "okay"; - }; - - serial at 13830000 { - status = "okay"; - }; - gpio-keys { compatible = "gpio-keys"; @@ -158,201 +122,6 @@ }; }; - i2c at 13890000 { - samsung,i2c-sda-delay = <100>; - samsung,i2c-slave-addr = <0x10>; - samsung,i2c-max-bus-freq = <400000>; - pinctrl-0 = <&i2c3_bus>; - pinctrl-names = "default"; - status = "okay"; - - mms114-touchscreen at 48 { - compatible = "melfas,mms114"; - reg = <0x48>; - interrupt-parent = <&gpx0>; - interrupts = <4 2>; - x-size = <720>; - y-size = <1280>; - avdd-supply = <&tsp_reg>; - vdd-supply = <&tsp_reg>; - }; - }; - - i2c at 138B0000 { - samsung,i2c-sda-delay = <100>; - samsung,i2c-slave-addr = <0x10>; - samsung,i2c-max-bus-freq = <100000>; - pinctrl-0 = <&i2c5_bus>; - pinctrl-names = "default"; - status = "okay"; - - max8997_pmic at 66 { - compatible = "maxim,max8997-pmic"; - - reg = <0x66>; - - max8997,pmic-buck1-uses-gpio-dvs; - max8997,pmic-buck2-uses-gpio-dvs; - max8997,pmic-buck5-uses-gpio-dvs; - - max8997,pmic-ignore-gpiodvs-side-effect; - max8997,pmic-buck125-default-dvs-idx = <0>; - - max8997,pmic-buck125-dvs-gpios = <&gpx0 5 0>, - <&gpx0 6 0>, - <&gpl0 0 0>; - - max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>, - <1250000>, <1200000>, - <1150000>, <1100000>, - <1000000>, <950000>; - - max8997,pmic-buck2-dvs-voltage = <1100000>, <1000000>, - <950000>, <900000>, - <1100000>, <1000000>, - <950000>, <900000>; - - max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>, - <1200000>, <1200000>, - <1200000>, <1200000>, - <1200000>, <1200000>; - - regulators { - valive_reg: LDO2 { - regulator-name = "VALIVE_1.1V_C210"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - regulator-always-on; - }; - - vusb_reg: LDO3 { - regulator-name = "VUSB_1.1V_C210"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - }; - - vmipi_reg: LDO4 { - regulator-name = "VMIPI_1.8V"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - }; - - vpda_reg: LDO6 { - regulator-name = "VCC_1.8V_PDA"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - }; - - vcam_reg: LDO7 { - regulator-name = "CAM_ISP_1.8V"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - }; - - vusbdac_reg: LDO8 { - regulator-name = "VUSB/VDAC_3.3V_C210"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - vccpda_reg: LDO9 { - regulator-name = "VCC_2.8V_PDA"; - regulator-min-microvolt = <2800000>; - regulator-max-microvolt = <2800000>; - regulator-always-on; - }; - - vpll_reg: LDO10 { - regulator-name = "VPLL_1.1V_C210"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - regulator-always-on; - }; - - vtcam_reg: LDO12 { - regulator-name = "VT_CAM_1.8V"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - }; - - vcclcd_reg: LDO13 { - regulator-name = "VCC_3.3V_LCD"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - vlcd_reg: LDO15 { - regulator-name = "VLCD_2.2V"; - regulator-min-microvolt = <2200000>; - regulator-max-microvolt = <2200000>; - }; - - camsensor_reg: LDO16 { - regulator-name = "CAM_SENSOR_IO_1.8V"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - }; - - vddq_reg: LDO21 { - regulator-name = "VDDQ_M1M2_1.2V"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-always-on; - }; - - varm_breg: BUCK1 { - /* - * HACK: The real name is VARM_1.2V_C210, - * but exynos-cpufreq does not support - * DT-based regulator lookup yet. - */ - regulator-name = "vdd_arm"; - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <1350000>; - regulator-always-on; - }; - - vint_breg: BUCK2 { - regulator-name = "VINT_1.1V_C210"; - regulator-min-microvolt = <900000>; - regulator-max-microvolt = <1100000>; - regulator-always-on; - }; - - camisp_breg: BUCK4 { - regulator-name = "CAM_ISP_CORE_1.2V"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - }; - - vmem_breg: BUCK5 { - regulator-name = "VMEM_1.2V_C210"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-always-on; - }; - - vccsub_breg: BUCK7 { - regulator-name = "VCC_SUB_2.0V"; - regulator-min-microvolt = <2000000>; - regulator-max-microvolt = <2000000>; - regulator-always-on; - }; - - safe1_sreg: ESAFEOUT1 { - regulator-name = "SAFEOUT1"; - regulator-always-on; - }; - - safe2_sreg: ESAFEOUT2 { - regulator-name = "SAFEOUT2"; - regulator-boot-on; - }; - }; - }; - }; - fixed-rate-clocks { xxti { compatible = "samsung,clock-xxti"; @@ -365,71 +134,6 @@ }; }; - dsi_0: dsi at 11C80000 { - vddcore-supply = <&vusb_reg>; - vddio-supply = <&vmipi_reg>; - samsung,pll-clock-frequency = <24000000>; - status = "okay"; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port at 1 { - reg = <1>; - - dsi_out: endpoint { - remote-endpoint = <&dsi_in>; - samsung,burst-clock-frequency = <500000000>; - samsung,esc-clock-frequency = <20000000>; - }; - }; - }; - - panel at 0 { - reg = <0>; - compatible = "samsung,s6e8aa0"; - vdd3-supply = <&vcclcd_reg>; - vci-supply = <&vlcd_reg>; - reset-gpios = <&gpy4 5 0>; - power-on-delay= <50>; - reset-delay = <100>; - init-delay = <100>; - flip-horizontal; - flip-vertical; - panel-width-mm = <58>; - panel-height-mm = <103>; - - display-timings { - timing-0 { - clock-frequency = <57153600>; - hactive = <720>; - vactive = <1280>; - hfront-porch = <5>; - hback-porch = <5>; - hsync-len = <5>; - vfront-porch = <13>; - vback-porch = <1>; - vsync-len = <2>; - }; - }; - - port { - dsi_in: endpoint { - remote-endpoint = <&dsi_out>; - }; - }; - }; - }; - - fimd at 11c00000 { - status = "okay"; - }; - - tmu at 100C0000 { - status = "okay"; - }; - thermal-zones { cpu_thermal: cpu-thermal { cooling-maps { @@ -483,3 +187,299 @@ }; }; }; + +&dsi_0 { + vddcore-supply = <&vusb_reg>; + vddio-supply = <&vmipi_reg>; + samsung,pll-clock-frequency = <24000000>; + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port at 1 { + reg = <1>; + + dsi_out: endpoint { + remote-endpoint = <&dsi_in>; + samsung,burst-clock-frequency = <500000000>; + samsung,esc-clock-frequency = <20000000>; + }; + }; + }; + + panel at 0 { + reg = <0>; + compatible = "samsung,s6e8aa0"; + vdd3-supply = <&vcclcd_reg>; + vci-supply = <&vlcd_reg>; + reset-gpios = <&gpy4 5 0>; + power-on-delay= <50>; + reset-delay = <100>; + init-delay = <100>; + flip-horizontal; + flip-vertical; + panel-width-mm = <58>; + panel-height-mm = <103>; + + display-timings { + timing-0 { + clock-frequency = <57153600>; + hactive = <720>; + vactive = <1280>; + hfront-porch = <5>; + hback-porch = <5>; + hsync-len = <5>; + vfront-porch = <13>; + vback-porch = <1>; + vsync-len = <2>; + }; + }; + + port { + dsi_in: endpoint { + remote-endpoint = <&dsi_out>; + }; + }; + }; +}; + +&exynos_usbphy { + status = "okay"; +}; + +&fimd { + status = "okay"; +}; + +&hsotg { + vusb_d-supply = <&vusb_reg>; + vusb_a-supply = <&vusbdac_reg>; + dr_mode = "peripheral"; + status = "okay"; +}; + +&i2c_3 { + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <400000>; + pinctrl-0 = <&i2c3_bus>; + pinctrl-names = "default"; + status = "okay"; + + mms114-touchscreen at 48 { + compatible = "melfas,mms114"; + reg = <0x48>; + interrupt-parent = <&gpx0>; + interrupts = <4 2>; + x-size = <720>; + y-size = <1280>; + avdd-supply = <&tsp_reg>; + vdd-supply = <&tsp_reg>; + }; +}; + +&i2c_5 { + samsung,i2c-sda-delay = <100>; + samsung,i2c-slave-addr = <0x10>; + samsung,i2c-max-bus-freq = <100000>; + pinctrl-0 = <&i2c5_bus>; + pinctrl-names = "default"; + status = "okay"; + + max8997_pmic at 66 { + compatible = "maxim,max8997-pmic"; + + reg = <0x66>; + + max8997,pmic-buck1-uses-gpio-dvs; + max8997,pmic-buck2-uses-gpio-dvs; + max8997,pmic-buck5-uses-gpio-dvs; + + max8997,pmic-ignore-gpiodvs-side-effect; + max8997,pmic-buck125-default-dvs-idx = <0>; + + max8997,pmic-buck125-dvs-gpios = <&gpx0 5 0>, + <&gpx0 6 0>, + <&gpl0 0 0>; + + max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>, + <1250000>, <1200000>, + <1150000>, <1100000>, + <1000000>, <950000>; + + max8997,pmic-buck2-dvs-voltage = <1100000>, <1000000>, + <950000>, <900000>, + <1100000>, <1000000>, + <950000>, <900000>; + + max8997,pmic-buck5-dvs-voltage = <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>; + + regulators { + valive_reg: LDO2 { + regulator-name = "VALIVE_1.1V_C210"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + vusb_reg: LDO3 { + regulator-name = "VUSB_1.1V_C210"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + }; + + vmipi_reg: LDO4 { + regulator-name = "VMIPI_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vpda_reg: LDO6 { + regulator-name = "VCC_1.8V_PDA"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + vcam_reg: LDO7 { + regulator-name = "CAM_ISP_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vusbdac_reg: LDO8 { + regulator-name = "VUSB/VDAC_3.3V_C210"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vccpda_reg: LDO9 { + regulator-name = "VCC_2.8V_PDA"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; + + vpll_reg: LDO10 { + regulator-name = "VPLL_1.1V_C210"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + vtcam_reg: LDO12 { + regulator-name = "VT_CAM_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vcclcd_reg: LDO13 { + regulator-name = "VCC_3.3V_LCD"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vlcd_reg: LDO15 { + regulator-name = "VLCD_2.2V"; + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + }; + + camsensor_reg: LDO16 { + regulator-name = "CAM_SENSOR_IO_1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vddq_reg: LDO21 { + regulator-name = "VDDQ_M1M2_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + varm_breg: BUCK1 { + /* + * HACK: The real name is VARM_1.2V_C210, + * but exynos-cpufreq does not support + * DT-based regulator lookup yet. + */ + regulator-name = "vdd_arm"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + vint_breg: BUCK2 { + regulator-name = "VINT_1.1V_C210"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + camisp_breg: BUCK4 { + regulator-name = "CAM_ISP_CORE_1.2V"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + vmem_breg: BUCK5 { + regulator-name = "VMEM_1.2V_C210"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + vccsub_breg: BUCK7 { + regulator-name = "VCC_SUB_2.0V"; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + regulator-always-on; + }; + + safe1_sreg: ESAFEOUT1 { + regulator-name = "SAFEOUT1"; + regulator-always-on; + }; + + safe2_sreg: ESAFEOUT2 { + regulator-name = "SAFEOUT2"; + regulator-boot-on; + }; + }; + }; +}; + +&sdhci_0 { + bus-width = <8>; + non-removable; + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>; + pinctrl-names = "default"; + vmmc-supply = <&vemmc_reg>; + status = "okay"; +}; + +&serial_0 { + status = "okay"; +}; + +&serial_1 { + status = "okay"; +}; + +&serial_2 { + status = "okay"; +}; + +&serial_3 { + status = "okay"; +}; + +&tmu { + status = "okay"; +}; -- 2.1.4
next prev parent reply other threads:[~2015-05-17 8:13 UTC|newest] Thread overview: 48+ messages / expand[flat|nested] mbox.gz Atom feed top 2015-05-17 8:09 [PATCH v6 00/13] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski 2015-05-17 8:09 ` Krzysztof Kozlowski 2015-05-17 8:09 ` Krzysztof Kozlowski 2015-05-17 8:09 ` [PATCH v6 01/13] ARM: dts: Add labels to exynos4 nodes Krzysztof Kozlowski 2015-05-17 8:09 ` Krzysztof Kozlowski 2015-05-17 8:09 ` [PATCH 1/4] ARM: multi_v7_defconfig: Enable CPU idle for Exynos Krzysztof Kozlowski 2015-05-17 8:09 ` Krzysztof Kozlowski 2015-05-17 8:09 ` [PATCH v6 02/13] ARM: dts: Use labels for overriding nodes in exynos4210 Krzysztof Kozlowski 2015-05-17 8:09 ` Krzysztof Kozlowski 2015-05-17 8:09 ` [PATCH 2/4] ARM: multi_v7_defconfig: Enable PMIC and MUIC drivers for Exynos boards Krzysztof Kozlowski 2015-05-17 8:09 ` Krzysztof Kozlowski 2015-05-17 8:09 ` [PATCH v6 03/13] ARM: dts: Use labels for overriding nodes in exynos4210-origen Krzysztof Kozlowski 2015-05-17 8:09 ` Krzysztof Kozlowski 2015-05-17 8:09 ` [PATCH 3/4] ARM: multi_v7_defconfig: Enable TMU for Exynos Krzysztof Kozlowski 2015-05-17 8:09 ` Krzysztof Kozlowski 2015-05-17 8:28 ` Krzysztof Kozłowski 2015-05-17 8:28 ` Krzysztof Kozłowski 2015-05-17 8:09 ` [PATCH v6 04/13] ARM: dts: Use labels for overriding nodes in exynos4210-smdkv310 Krzysztof Kozlowski 2015-05-17 8:09 ` Krzysztof Kozlowski 2015-05-17 8:09 ` [PATCH 4/4] ARM: multi_v7_defconfig: Enable OHCI on Exynos Krzysztof Kozlowski 2015-05-17 8:09 ` Krzysztof Kozlowski 2015-05-17 8:09 ` Krzysztof Kozlowski 2015-05-17 8:27 ` Krzysztof Kozłowski 2015-05-17 8:27 ` Krzysztof Kozłowski 2015-05-17 8:27 ` Krzysztof Kozłowski 2015-05-17 8:09 ` Krzysztof Kozlowski [this message] 2015-05-17 8:09 ` [PATCH v6 05/13] ARM: dts: Use labels for overriding nodes in exynos4210-trats Krzysztof Kozlowski 2015-05-17 8:09 ` [PATCH v6 06/13] ARM: dts: Use labels for overriding nodes in exynos4212 Krzysztof Kozlowski 2015-05-17 8:09 ` Krzysztof Kozlowski 2015-05-17 8:09 ` Krzysztof Kozlowski 2015-05-17 8:09 ` [PATCH v6 07/13] ARM: dts: Use labels for overriding nodes in exynos4x12 Krzysztof Kozlowski 2015-05-17 8:09 ` Krzysztof Kozlowski 2015-05-17 8:09 ` Krzysztof Kozlowski 2015-05-17 8:09 ` [PATCH v6 08/13] ARM: dts: Use labels for overriding nodes in exynos4412 Krzysztof Kozlowski 2015-05-17 8:09 ` Krzysztof Kozlowski 2015-05-17 8:09 ` Krzysztof Kozlowski 2015-05-17 8:09 ` [PATCH v6 09/13] ARM: dts: Use labels for overriding nodes in exynos4412-odroid Krzysztof Kozlowski 2015-05-17 8:09 ` Krzysztof Kozlowski 2015-05-17 8:30 ` [PATCH v6 10/13] ARM: dts: Use labels for overriding nodes in exynos4412-smdk4412 Krzysztof Kozlowski 2015-05-17 8:30 ` Krzysztof Kozlowski 2015-05-17 8:30 ` [PATCH v6 11/13] ARM: dts: Use labels for overriding nodes in exynos4412-trats2 Krzysztof Kozlowski 2015-05-17 8:30 ` Krzysztof Kozlowski 2015-05-17 8:30 ` [PATCH v6 12/13] ARM: dts: Use labels for overriding nodes in exynos4412-origen Krzysztof Kozlowski 2015-05-17 8:30 ` Krzysztof Kozlowski 2015-05-17 8:30 ` [PATCH v6 13/13] ARM: dts: Use labels for overriding nodes in exynos4412-tiny4412 Krzysztof Kozlowski 2015-05-17 8:30 ` Krzysztof Kozlowski 2015-05-23 3:58 ` [PATCH v6 00/13] ARM: dts: exynos4: labels for overriding nodes Kukjin Kim 2015-05-23 3:58 ` Kukjin Kim
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1431850195-9558-10-git-send-email-k.kozlowski.k@gmail.com \ --to=k.kozlowski.k@gmail.com \ --cc=devicetree@vger.kernel.org \ --cc=kgene@kernel.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-samsung-soc@vger.kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.