From: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
To: Kukjin Kim <kgene@kernel.org>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-samsung-soc@vger.kernel.org, linux-kernel@vger.kernel.org
Cc: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Subject: [PATCH v6 09/13] ARM: dts: Use labels for overriding nodes in exynos4412-odroid
Date: Sun, 17 May 2015 17:09:55 +0900 [thread overview]
Message-ID: <1431850195-9558-14-git-send-email-k.kozlowski.k@gmail.com> (raw)
In-Reply-To: <1431850195-9558-1-git-send-email-k.kozlowski.k@gmail.com>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
For thermal zones:
Acked-by: Eduardo Valentin <edubezval@gmail.com>
---
arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 732 ++++++++++++------------
arch/arm/boot/dts/exynos4412-odroidx.dts | 16 +-
2 files changed, 374 insertions(+), 374 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
index d6b49e5b32e9..ca7d168d1dd6 100644
--- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
+++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
@@ -38,16 +38,6 @@
};
};
- i2s0: i2s@03830000 {
- pinctrl-0 = <&i2s0_bus>;
- pinctrl-names = "default";
- status = "okay";
- clocks = <&clock_audss EXYNOS_I2S_BUS>,
- <&clock_audss EXYNOS_DOUT_AUD_BUS>,
- <&clock_audss EXYNOS_SCLK_I2S>;
- clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
- };
-
sound: sound {
compatible = "simple-audio-card";
assigned-clocks = <&clock_audss EXYNOS_MOUT_AUDSS>,
@@ -83,427 +73,437 @@
reset-gpios = <&gpk1 2 1>;
};
- mmc@12550000 {
- pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
- pinctrl-names = "default";
- vmmc-supply = <&ldo20_reg &buck8_reg>;
- mmc-pwrseq = <&emmc_pwrseq>;
- status = "okay";
-
- num-slots = <1>;
- broken-cd;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- bus-width = <8>;
- cap-mmc-highspeed;
- };
-
- watchdog@10060000 {
- status = "okay";
- };
-
- rtc@10070000 {
- status = "okay";
- clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
- clock-names = "rtc", "rtc_src";
- };
-
- g2d@10800000 {
- status = "okay";
- };
-
camera {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
+ };
- fimc_0: fimc@11800000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC0>,
- <&clock CLK_SCLK_FIMC0>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
- };
-
- fimc_1: fimc@11810000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC1>,
- <&clock CLK_SCLK_FIMC1>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
+ fixed-rate-clocks {
+ xxti {
+ compatible = "samsung,clock-xxti";
+ clock-frequency = <0>;
};
- fimc_2: fimc@11820000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC2>,
- <&clock CLK_SCLK_FIMC2>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
+ xusbxti {
+ compatible = "samsung,clock-xusbxti";
+ clock-frequency = <24000000>;
};
+ };
- fimc_3: fimc@11830000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC3>,
- <&clock CLK_SCLK_FIMC3>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ cooling-maps {
+ map0 {
+ /* Corresponds to 800MHz at freq_table */
+ cooling-device = <&cpu0 7 7>;
+ };
+ map1 {
+ /* Corresponds to 200MHz at freq_table */
+ cooling-device = <&cpu0 13 13>;
+ };
+ };
};
};
+};
- sdhci@12530000 {
- bus-width = <4>;
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
- pinctrl-names = "default";
- vmmc-supply = <&ldo4_reg &ldo21_reg>;
- cd-gpios = <&gpk2 2 0>;
- cd-inverted;
- status = "okay";
- };
+/* RSTN signal for eMMC */
+&sd1_cd {
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+};
- serial@13800000 {
- status = "okay";
+&pinctrl_1 {
+ gpio_power_key: power_key {
+ samsung,pins = "gpx1-3";
+ samsung,pin-pud = <0>;
};
- serial@13810000 {
- status = "okay";
+ max77686_irq: max77686-irq {
+ samsung,pins = "gpx3-2";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
};
- fixed-rate-clocks {
- xxti {
- compatible = "samsung,clock-xxti";
- clock-frequency = <0>;
- };
-
- xusbxti {
- compatible = "samsung,clock-xusbxti";
- clock-frequency = <24000000>;
- };
+ hdmi_hpd: hdmi-hpd {
+ samsung,pins = "gpx3-7";
+ samsung,pin-pud = <1>;
};
+};
- i2c@13860000 {
- pinctrl-0 = <&i2c0_bus>;
- pinctrl-names = "default";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <400000>;
- status = "okay";
+&ehci {
+ status = "okay";
+};
- usb3503: usb3503@08 {
- compatible = "smsc,usb3503";
- reg = <0x08>;
+&exynos_usbphy {
+ status = "okay";
+};
- intn-gpios = <&gpx3 0 0>;
- connect-gpios = <&gpx3 4 0>;
- reset-gpios = <&gpx3 5 0>;
- initial-mode = <1>;
- };
+&fimc_0 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC0>,
+ <&clock CLK_SCLK_FIMC0>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
- max77686: pmic@09 {
- compatible = "maxim,max77686";
- interrupt-parent = <&gpx3>;
- interrupts = <2 0>;
- pinctrl-names = "default";
- pinctrl-0 = <&max77686_irq>;
- reg = <0x09>;
- #clock-cells = <1>;
-
- voltage-regulators {
- ldo1_reg: LDO1 {
- regulator-name = "VDD_ALIVE_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
+&fimc_1 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC1>,
+ <&clock CLK_SCLK_FIMC1>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
- ldo2_reg: LDO2 {
- regulator-name = "VDDQ_M1_2_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
+&fimc_2 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC2>,
+ <&clock CLK_SCLK_FIMC2>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
- ldo3_reg: LDO3 {
- regulator-name = "VDDQ_EXT_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
+&fimc_3 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC3>,
+ <&clock CLK_SCLK_FIMC3>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
- ldo4_reg: LDO4 {
- regulator-name = "VDDQ_MMC2_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+&g2d {
+ status = "okay";
+};
- ldo5_reg: LDO5 {
- regulator-name = "VDDQ_MMC1_3_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+&hdmi {
+ hpd-gpio = <&gpx3 7 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_hpd>;
+ vdd-supply = <&ldo8_reg>;
+ vdd_osc-supply = <&ldo10_reg>;
+ vdd_pll-supply = <&ldo8_reg>;
+ ddc = <&i2c_2>;
+ status = "okay";
+};
- ldo6_reg: LDO6 {
- regulator-name = "VDD10_MPLL_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
+&hsotg {
+ dr_mode = "peripheral";
+ status = "okay";
+ vusb_d-supply = <&ldo15_reg>;
+ vusb_a-supply = <&ldo12_reg>;
+};
- ldo7_reg: LDO7 {
- regulator-name = "VDD10_XPLL_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
+&i2c_0 {
+ pinctrl-0 = <&i2c0_bus>;
+ pinctrl-names = "default";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <400000>;
+ status = "okay";
+
+ usb3503: usb3503@08 {
+ compatible = "smsc,usb3503";
+ reg = <0x08>;
+
+ intn-gpios = <&gpx3 0 0>;
+ connect-gpios = <&gpx3 4 0>;
+ reset-gpios = <&gpx3 5 0>;
+ initial-mode = <1>;
+ };
- ldo8_reg: ldo@8 {
- regulator-compatible = "LDO8";
- regulator-name = "VDD10_HDMI_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- };
+ max77686: pmic@09 {
+ compatible = "maxim,max77686";
+ interrupt-parent = <&gpx3>;
+ interrupts = <2 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&max77686_irq>;
+ reg = <0x09>;
+ #clock-cells = <1>;
+
+ voltage-regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "VDD_ALIVE_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
- ldo10_reg: ldo@10 {
- regulator-compatible = "LDO10";
- regulator-name = "VDDQ_MIPIHSI_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
+ ldo2_reg: LDO2 {
+ regulator-name = "VDDQ_M1_2_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
- ldo11_reg: LDO11 {
- regulator-name = "VDD18_ABB1_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
+ ldo3_reg: LDO3 {
+ regulator-name = "VDDQ_EXT_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
- ldo12_reg: LDO12 {
- regulator-name = "VDD33_USB_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo4_reg: LDO4 {
+ regulator-name = "VDDQ_MMC2_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- ldo13_reg: LDO13 {
- regulator-name = "VDDQ_C2C_W_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo5_reg: LDO5 {
+ regulator-name = "VDDQ_MMC1_3_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- ldo14_reg: LDO14 {
- regulator-name = "VDD18_ABB0_2_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo6_reg: LDO6 {
+ regulator-name = "VDD10_MPLL_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
- ldo15_reg: LDO15 {
- regulator-name = "VDD10_HSIC_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo7_reg: LDO7 {
+ regulator-name = "VDD10_XPLL_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
- ldo16_reg: LDO16 {
- regulator-name = "VDD18_HSIC_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo8_reg: ldo@8 {
+ regulator-compatible = "LDO8";
+ regulator-name = "VDD10_HDMI_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
- ldo20_reg: LDO20 {
- regulator-name = "LDO20_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-boot-on;
- };
+ ldo10_reg: ldo@10 {
+ regulator-compatible = "LDO10";
+ regulator-name = "VDDQ_MIPIHSI_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- ldo21_reg: LDO21 {
- regulator-name = "LDO21_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo11_reg: LDO11 {
+ regulator-name = "VDD18_ABB1_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
- ldo25_reg: LDO25 {
- regulator-name = "VDDQ_LCD_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo12_reg: LDO12 {
+ regulator-name = "VDD33_USB_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck1_reg: BUCK1 {
- regulator-name = "vdd_mif";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo13_reg: LDO13 {
+ regulator-name = "VDDQ_C2C_W_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck2_reg: BUCK2 {
- regulator-name = "vdd_arm";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo14_reg: LDO14 {
+ regulator-name = "VDD18_ABB0_2_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck3_reg: BUCK3 {
- regulator-name = "vdd_int";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo15_reg: LDO15 {
+ regulator-name = "VDD10_HSIC_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck4_reg: BUCK4 {
- regulator-name = "vdd_g3d";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1100000>;
- regulator-microvolt-offset = <50000>;
- };
+ ldo16_reg: LDO16 {
+ regulator-name = "VDD18_HSIC_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck5_reg: BUCK5 {
- regulator-name = "VDDQ_CKEM1_2_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo20_reg: LDO20 {
+ regulator-name = "LDO20_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
- buck6_reg: BUCK6 {
- regulator-name = "BUCK6_1.35V";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo21_reg: LDO21 {
+ regulator-name = "LDO21_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck7_reg: BUCK7 {
- regulator-name = "BUCK7_2.0V";
- regulator-min-microvolt = <2000000>;
- regulator-max-microvolt = <2000000>;
- regulator-always-on;
- };
+ ldo25_reg: LDO25 {
+ regulator-name = "VDDQ_LCD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck8_reg: BUCK8 {
- regulator-name = "BUCK8_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
+ buck1_reg: BUCK1 {
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
};
- };
- };
- i2c@13870000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_bus>;
- status = "okay";
- max98090: max98090@10 {
- compatible = "maxim,max98090";
- reg = <0x10>;
- interrupt-parent = <&gpx0>;
- interrupts = <0 0>;
- clocks = <&i2s0 CLK_I2S_CDCLK>;
- clock-names = "mclk";
- #sound-dai-cells = <0>;
- };
- };
+ buck2_reg: BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- exynos-usbphy@125B0000 {
- status = "okay";
- };
+ buck3_reg: BUCK3 {
+ regulator-name = "vdd_int";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- hsotg@12480000 {
- dr_mode = "peripheral";
- status = "okay";
- vusb_d-supply = <&ldo15_reg>;
- vusb_a-supply = <&ldo12_reg>;
- };
+ buck4_reg: BUCK4 {
+ regulator-name = "vdd_g3d";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-microvolt-offset = <50000>;
+ };
- ehci: ehci@12580000 {
- status = "okay";
- };
+ buck5_reg: BUCK5 {
+ regulator-name = "VDDQ_CKEM1_2_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- tmu@100C0000 {
- vtmu-supply = <&ldo10_reg>;
- status = "okay";
- };
+ buck6_reg: BUCK6 {
+ regulator-name = "BUCK6_1.35V";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- thermal-zones {
- cpu_thermal: cpu-thermal {
- cooling-maps {
- map0 {
- /* Corresponds to 800MHz at freq_table */
- cooling-device = <&cpu0 7 7>;
- };
- map1 {
- /* Corresponds to 200MHz at freq_table */
- cooling-device = <&cpu0 13 13>;
- };
- };
+ buck7_reg: BUCK7 {
+ regulator-name = "BUCK7_2.0V";
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-always-on;
+ };
+
+ buck8_reg: BUCK8 {
+ regulator-name = "BUCK8_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
};
};
+};
- mixer: mixer@12C10000 {
- status = "okay";
+&i2c_1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_bus>;
+ status = "okay";
+ max98090: max98090@10 {
+ compatible = "maxim,max98090";
+ reg = <0x10>;
+ interrupt-parent = <&gpx0>;
+ interrupts = <0 0>;
+ clocks = <&i2s0 CLK_I2S_CDCLK>;
+ clock-names = "mclk";
+ #sound-dai-cells = <0>;
};
+};
- hdmi@12D00000 {
- hpd-gpio = <&gpx3 7 0>;
- pinctrl-names = "default";
- pinctrl-0 = <&hdmi_hpd>;
- vdd-supply = <&ldo8_reg>;
- vdd_osc-supply = <&ldo10_reg>;
- vdd_pll-supply = <&ldo8_reg>;
- ddc = <&hdmi_ddc>;
- status = "okay";
- };
+&i2c_2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_bus>;
+};
- hdmi_ddc: i2c@13880000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_bus>;
- };
+&i2c_8 {
+ status = "okay";
+};
- i2c@138E0000 {
- status = "okay";
- };
+&i2s0 {
+ pinctrl-0 = <&i2s0_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+ clocks = <&clock_audss EXYNOS_I2S_BUS>,
+ <&clock_audss EXYNOS_DOUT_AUD_BUS>,
+ <&clock_audss EXYNOS_SCLK_I2S>;
+ clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
};
-/* RSTN signal for eMMC */
-&sd1_cd {
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+&mixer {
+ status = "okay";
};
-&pinctrl_1 {
- gpio_power_key: power_key {
- samsung,pins = "gpx1-3";
- samsung,pin-pud = <0>;
- };
+&mshc_0 {
+ pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
+ pinctrl-names = "default";
+ vmmc-supply = <&ldo20_reg &buck8_reg>;
+ mmc-pwrseq = <&emmc_pwrseq>;
+ status = "okay";
+
+ num-slots = <1>;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ bus-width = <8>;
+ cap-mmc-highspeed;
+};
- max77686_irq: max77686-irq {
- samsung,pins = "gpx3-2";
- samsung,pin-function = <0>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
+&rtc {
+ status = "okay";
+ clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
+ clock-names = "rtc", "rtc_src";
+};
- hdmi_hpd: hdmi-hpd {
- samsung,pins = "gpx3-7";
- samsung,pin-pud = <1>;
- };
+&sdhci_2 {
+ bus-width = <4>;
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
+ pinctrl-names = "default";
+ vmmc-supply = <&ldo4_reg &ldo21_reg>;
+ cd-gpios = <&gpk2 2 0>;
+ cd-inverted;
+ status = "okay";
+};
+
+&serial_0 {
+ status = "okay";
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&tmu {
+ vtmu-supply = <&ldo10_reg>;
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
};
diff --git a/arch/arm/boot/dts/exynos4412-odroidx.dts b/arch/arm/boot/dts/exynos4412-odroidx.dts
index cb1cfe7239c4..679ac103ebf6 100644
--- a/arch/arm/boot/dts/exynos4412-odroidx.dts
+++ b/arch/arm/boot/dts/exynos4412-odroidx.dts
@@ -38,14 +38,6 @@
};
};
- serial@13820000 {
- status = "okay";
- };
-
- serial@13830000 {
- status = "okay";
- };
-
gpio_keys {
pinctrl-0 = <&gpio_power_key &gpio_home_key>;
@@ -83,3 +75,11 @@
samsung,pin-pud = <0>;
};
};
+
+&serial_2 {
+ status = "okay";
+};
+
+&serial_3 {
+ status = "okay";
+};
--
2.1.4
WARNING: multiple messages have this Message-ID (diff)
From: k.kozlowski.k@gmail.com (Krzysztof Kozlowski)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v6 09/13] ARM: dts: Use labels for overriding nodes in exynos4412-odroid
Date: Sun, 17 May 2015 17:09:55 +0900 [thread overview]
Message-ID: <1431850195-9558-14-git-send-email-k.kozlowski.k@gmail.com> (raw)
In-Reply-To: <1431850195-9558-1-git-send-email-k.kozlowski.k@gmail.com>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
For thermal zones:
Acked-by: Eduardo Valentin <edubezval@gmail.com>
---
arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 732 ++++++++++++------------
arch/arm/boot/dts/exynos4412-odroidx.dts | 16 +-
2 files changed, 374 insertions(+), 374 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
index d6b49e5b32e9..ca7d168d1dd6 100644
--- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
+++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
@@ -38,16 +38,6 @@
};
};
- i2s0: i2s at 03830000 {
- pinctrl-0 = <&i2s0_bus>;
- pinctrl-names = "default";
- status = "okay";
- clocks = <&clock_audss EXYNOS_I2S_BUS>,
- <&clock_audss EXYNOS_DOUT_AUD_BUS>,
- <&clock_audss EXYNOS_SCLK_I2S>;
- clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
- };
-
sound: sound {
compatible = "simple-audio-card";
assigned-clocks = <&clock_audss EXYNOS_MOUT_AUDSS>,
@@ -83,427 +73,437 @@
reset-gpios = <&gpk1 2 1>;
};
- mmc at 12550000 {
- pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
- pinctrl-names = "default";
- vmmc-supply = <&ldo20_reg &buck8_reg>;
- mmc-pwrseq = <&emmc_pwrseq>;
- status = "okay";
-
- num-slots = <1>;
- broken-cd;
- card-detect-delay = <200>;
- samsung,dw-mshc-ciu-div = <3>;
- samsung,dw-mshc-sdr-timing = <2 3>;
- samsung,dw-mshc-ddr-timing = <1 2>;
- bus-width = <8>;
- cap-mmc-highspeed;
- };
-
- watchdog at 10060000 {
- status = "okay";
- };
-
- rtc at 10070000 {
- status = "okay";
- clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
- clock-names = "rtc", "rtc_src";
- };
-
- g2d at 10800000 {
- status = "okay";
- };
-
camera {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <>;
+ };
- fimc_0: fimc at 11800000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC0>,
- <&clock CLK_SCLK_FIMC0>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
- };
-
- fimc_1: fimc at 11810000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC1>,
- <&clock CLK_SCLK_FIMC1>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
+ fixed-rate-clocks {
+ xxti {
+ compatible = "samsung,clock-xxti";
+ clock-frequency = <0>;
};
- fimc_2: fimc at 11820000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC2>,
- <&clock CLK_SCLK_FIMC2>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
+ xusbxti {
+ compatible = "samsung,clock-xusbxti";
+ clock-frequency = <24000000>;
};
+ };
- fimc_3: fimc at 11830000 {
- status = "okay";
- assigned-clocks = <&clock CLK_MOUT_FIMC3>,
- <&clock CLK_SCLK_FIMC3>;
- assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
- assigned-clock-rates = <0>, <176000000>;
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ cooling-maps {
+ map0 {
+ /* Corresponds to 800MHz at freq_table */
+ cooling-device = <&cpu0 7 7>;
+ };
+ map1 {
+ /* Corresponds to 200MHz at freq_table */
+ cooling-device = <&cpu0 13 13>;
+ };
+ };
};
};
+};
- sdhci at 12530000 {
- bus-width = <4>;
- pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
- pinctrl-names = "default";
- vmmc-supply = <&ldo4_reg &ldo21_reg>;
- cd-gpios = <&gpk2 2 0>;
- cd-inverted;
- status = "okay";
- };
+/* RSTN signal for eMMC */
+&sd1_cd {
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+};
- serial at 13800000 {
- status = "okay";
+&pinctrl_1 {
+ gpio_power_key: power_key {
+ samsung,pins = "gpx1-3";
+ samsung,pin-pud = <0>;
};
- serial at 13810000 {
- status = "okay";
+ max77686_irq: max77686-irq {
+ samsung,pins = "gpx3-2";
+ samsung,pin-function = <0>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
};
- fixed-rate-clocks {
- xxti {
- compatible = "samsung,clock-xxti";
- clock-frequency = <0>;
- };
-
- xusbxti {
- compatible = "samsung,clock-xusbxti";
- clock-frequency = <24000000>;
- };
+ hdmi_hpd: hdmi-hpd {
+ samsung,pins = "gpx3-7";
+ samsung,pin-pud = <1>;
};
+};
- i2c at 13860000 {
- pinctrl-0 = <&i2c0_bus>;
- pinctrl-names = "default";
- samsung,i2c-sda-delay = <100>;
- samsung,i2c-max-bus-freq = <400000>;
- status = "okay";
+&ehci {
+ status = "okay";
+};
- usb3503: usb3503 at 08 {
- compatible = "smsc,usb3503";
- reg = <0x08>;
+&exynos_usbphy {
+ status = "okay";
+};
- intn-gpios = <&gpx3 0 0>;
- connect-gpios = <&gpx3 4 0>;
- reset-gpios = <&gpx3 5 0>;
- initial-mode = <1>;
- };
+&fimc_0 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC0>,
+ <&clock CLK_SCLK_FIMC0>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
- max77686: pmic at 09 {
- compatible = "maxim,max77686";
- interrupt-parent = <&gpx3>;
- interrupts = <2 0>;
- pinctrl-names = "default";
- pinctrl-0 = <&max77686_irq>;
- reg = <0x09>;
- #clock-cells = <1>;
-
- voltage-regulators {
- ldo1_reg: LDO1 {
- regulator-name = "VDD_ALIVE_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
+&fimc_1 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC1>,
+ <&clock CLK_SCLK_FIMC1>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
- ldo2_reg: LDO2 {
- regulator-name = "VDDQ_M1_2_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
+&fimc_2 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC2>,
+ <&clock CLK_SCLK_FIMC2>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
- ldo3_reg: LDO3 {
- regulator-name = "VDDQ_EXT_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
+&fimc_3 {
+ status = "okay";
+ assigned-clocks = <&clock CLK_MOUT_FIMC3>,
+ <&clock CLK_SCLK_FIMC3>;
+ assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
+ assigned-clock-rates = <0>, <176000000>;
+};
- ldo4_reg: LDO4 {
- regulator-name = "VDDQ_MMC2_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+&g2d {
+ status = "okay";
+};
- ldo5_reg: LDO5 {
- regulator-name = "VDDQ_MMC1_3_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+&hdmi {
+ hpd-gpio = <&gpx3 7 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_hpd>;
+ vdd-supply = <&ldo8_reg>;
+ vdd_osc-supply = <&ldo10_reg>;
+ vdd_pll-supply = <&ldo8_reg>;
+ ddc = <&i2c_2>;
+ status = "okay";
+};
- ldo6_reg: LDO6 {
- regulator-name = "VDD10_MPLL_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
+&hsotg {
+ dr_mode = "peripheral";
+ status = "okay";
+ vusb_d-supply = <&ldo15_reg>;
+ vusb_a-supply = <&ldo12_reg>;
+};
- ldo7_reg: LDO7 {
- regulator-name = "VDD10_XPLL_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- };
+&i2c_0 {
+ pinctrl-0 = <&i2c0_bus>;
+ pinctrl-names = "default";
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-max-bus-freq = <400000>;
+ status = "okay";
+
+ usb3503: usb3503 at 08 {
+ compatible = "smsc,usb3503";
+ reg = <0x08>;
+
+ intn-gpios = <&gpx3 0 0>;
+ connect-gpios = <&gpx3 4 0>;
+ reset-gpios = <&gpx3 5 0>;
+ initial-mode = <1>;
+ };
- ldo8_reg: ldo at 8 {
- regulator-compatible = "LDO8";
- regulator-name = "VDD10_HDMI_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- };
+ max77686: pmic at 09 {
+ compatible = "maxim,max77686";
+ interrupt-parent = <&gpx3>;
+ interrupts = <2 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&max77686_irq>;
+ reg = <0x09>;
+ #clock-cells = <1>;
+
+ voltage-regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "VDD_ALIVE_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
- ldo10_reg: ldo at 10 {
- regulator-compatible = "LDO10";
- regulator-name = "VDDQ_MIPIHSI_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- };
+ ldo2_reg: LDO2 {
+ regulator-name = "VDDQ_M1_2_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
- ldo11_reg: LDO11 {
- regulator-name = "VDD18_ABB1_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
+ ldo3_reg: LDO3 {
+ regulator-name = "VDDQ_EXT_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
- ldo12_reg: LDO12 {
- regulator-name = "VDD33_USB_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo4_reg: LDO4 {
+ regulator-name = "VDDQ_MMC2_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- ldo13_reg: LDO13 {
- regulator-name = "VDDQ_C2C_W_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo5_reg: LDO5 {
+ regulator-name = "VDDQ_MMC1_3_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- ldo14_reg: LDO14 {
- regulator-name = "VDD18_ABB0_2_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo6_reg: LDO6 {
+ regulator-name = "VDD10_MPLL_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
- ldo15_reg: LDO15 {
- regulator-name = "VDD10_HSIC_1.0V";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo7_reg: LDO7 {
+ regulator-name = "VDD10_XPLL_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
- ldo16_reg: LDO16 {
- regulator-name = "VDD18_HSIC_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo8_reg: ldo at 8 {
+ regulator-compatible = "LDO8";
+ regulator-name = "VDD10_HDMI_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
- ldo20_reg: LDO20 {
- regulator-name = "LDO20_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-boot-on;
- };
+ ldo10_reg: ldo at 10 {
+ regulator-compatible = "LDO10";
+ regulator-name = "VDDQ_MIPIHSI_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
- ldo21_reg: LDO21 {
- regulator-name = "LDO21_3.3V";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo11_reg: LDO11 {
+ regulator-name = "VDD18_ABB1_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
- ldo25_reg: LDO25 {
- regulator-name = "VDDQ_LCD_1.8V";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo12_reg: LDO12 {
+ regulator-name = "VDD33_USB_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck1_reg: BUCK1 {
- regulator-name = "vdd_mif";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo13_reg: LDO13 {
+ regulator-name = "VDDQ_C2C_W_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck2_reg: BUCK2 {
- regulator-name = "vdd_arm";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo14_reg: LDO14 {
+ regulator-name = "VDD18_ABB0_2_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck3_reg: BUCK3 {
- regulator-name = "vdd_int";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo15_reg: LDO15 {
+ regulator-name = "VDD10_HSIC_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck4_reg: BUCK4 {
- regulator-name = "vdd_g3d";
- regulator-min-microvolt = <900000>;
- regulator-max-microvolt = <1100000>;
- regulator-microvolt-offset = <50000>;
- };
+ ldo16_reg: LDO16 {
+ regulator-name = "VDD18_HSIC_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck5_reg: BUCK5 {
- regulator-name = "VDDQ_CKEM1_2_1.2V";
- regulator-min-microvolt = <1200000>;
- regulator-max-microvolt = <1200000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo20_reg: LDO20 {
+ regulator-name = "LDO20_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
- buck6_reg: BUCK6 {
- regulator-name = "BUCK6_1.35V";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ ldo21_reg: LDO21 {
+ regulator-name = "LDO21_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck7_reg: BUCK7 {
- regulator-name = "BUCK7_2.0V";
- regulator-min-microvolt = <2000000>;
- regulator-max-microvolt = <2000000>;
- regulator-always-on;
- };
+ ldo25_reg: LDO25 {
+ regulator-name = "VDDQ_LCD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- buck8_reg: BUCK8 {
- regulator-name = "BUCK8_2.8V";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- };
+ buck1_reg: BUCK1 {
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
};
- };
- };
- i2c at 13870000 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_bus>;
- status = "okay";
- max98090: max98090 at 10 {
- compatible = "maxim,max98090";
- reg = <0x10>;
- interrupt-parent = <&gpx0>;
- interrupts = <0 0>;
- clocks = <&i2s0 CLK_I2S_CDCLK>;
- clock-names = "mclk";
- #sound-dai-cells = <0>;
- };
- };
+ buck2_reg: BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- exynos-usbphy at 125B0000 {
- status = "okay";
- };
+ buck3_reg: BUCK3 {
+ regulator-name = "vdd_int";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- hsotg at 12480000 {
- dr_mode = "peripheral";
- status = "okay";
- vusb_d-supply = <&ldo15_reg>;
- vusb_a-supply = <&ldo12_reg>;
- };
+ buck4_reg: BUCK4 {
+ regulator-name = "vdd_g3d";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-microvolt-offset = <50000>;
+ };
- ehci: ehci at 12580000 {
- status = "okay";
- };
+ buck5_reg: BUCK5 {
+ regulator-name = "VDDQ_CKEM1_2_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- tmu at 100C0000 {
- vtmu-supply = <&ldo10_reg>;
- status = "okay";
- };
+ buck6_reg: BUCK6 {
+ regulator-name = "BUCK6_1.35V";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
- thermal-zones {
- cpu_thermal: cpu-thermal {
- cooling-maps {
- map0 {
- /* Corresponds to 800MHz at freq_table */
- cooling-device = <&cpu0 7 7>;
- };
- map1 {
- /* Corresponds to 200MHz at freq_table */
- cooling-device = <&cpu0 13 13>;
- };
- };
+ buck7_reg: BUCK7 {
+ regulator-name = "BUCK7_2.0V";
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-always-on;
+ };
+
+ buck8_reg: BUCK8 {
+ regulator-name = "BUCK8_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
};
};
+};
- mixer: mixer at 12C10000 {
- status = "okay";
+&i2c_1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_bus>;
+ status = "okay";
+ max98090: max98090 at 10 {
+ compatible = "maxim,max98090";
+ reg = <0x10>;
+ interrupt-parent = <&gpx0>;
+ interrupts = <0 0>;
+ clocks = <&i2s0 CLK_I2S_CDCLK>;
+ clock-names = "mclk";
+ #sound-dai-cells = <0>;
};
+};
- hdmi at 12D00000 {
- hpd-gpio = <&gpx3 7 0>;
- pinctrl-names = "default";
- pinctrl-0 = <&hdmi_hpd>;
- vdd-supply = <&ldo8_reg>;
- vdd_osc-supply = <&ldo10_reg>;
- vdd_pll-supply = <&ldo8_reg>;
- ddc = <&hdmi_ddc>;
- status = "okay";
- };
+&i2c_2 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_bus>;
+};
- hdmi_ddc: i2c at 13880000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_bus>;
- };
+&i2c_8 {
+ status = "okay";
+};
- i2c at 138E0000 {
- status = "okay";
- };
+&i2s0 {
+ pinctrl-0 = <&i2s0_bus>;
+ pinctrl-names = "default";
+ status = "okay";
+ clocks = <&clock_audss EXYNOS_I2S_BUS>,
+ <&clock_audss EXYNOS_DOUT_AUD_BUS>,
+ <&clock_audss EXYNOS_SCLK_I2S>;
+ clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
};
-/* RSTN signal for eMMC */
-&sd1_cd {
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
+&mixer {
+ status = "okay";
};
-&pinctrl_1 {
- gpio_power_key: power_key {
- samsung,pins = "gpx1-3";
- samsung,pin-pud = <0>;
- };
+&mshc_0 {
+ pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
+ pinctrl-names = "default";
+ vmmc-supply = <&ldo20_reg &buck8_reg>;
+ mmc-pwrseq = <&emmc_pwrseq>;
+ status = "okay";
+
+ num-slots = <1>;
+ broken-cd;
+ card-detect-delay = <200>;
+ samsung,dw-mshc-ciu-div = <3>;
+ samsung,dw-mshc-sdr-timing = <2 3>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ bus-width = <8>;
+ cap-mmc-highspeed;
+};
- max77686_irq: max77686-irq {
- samsung,pins = "gpx3-2";
- samsung,pin-function = <0>;
- samsung,pin-pud = <0>;
- samsung,pin-drv = <0>;
- };
+&rtc {
+ status = "okay";
+ clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
+ clock-names = "rtc", "rtc_src";
+};
- hdmi_hpd: hdmi-hpd {
- samsung,pins = "gpx3-7";
- samsung,pin-pud = <1>;
- };
+&sdhci_2 {
+ bus-width = <4>;
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
+ pinctrl-names = "default";
+ vmmc-supply = <&ldo4_reg &ldo21_reg>;
+ cd-gpios = <&gpk2 2 0>;
+ cd-inverted;
+ status = "okay";
+};
+
+&serial_0 {
+ status = "okay";
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&tmu {
+ vtmu-supply = <&ldo10_reg>;
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
};
diff --git a/arch/arm/boot/dts/exynos4412-odroidx.dts b/arch/arm/boot/dts/exynos4412-odroidx.dts
index cb1cfe7239c4..679ac103ebf6 100644
--- a/arch/arm/boot/dts/exynos4412-odroidx.dts
+++ b/arch/arm/boot/dts/exynos4412-odroidx.dts
@@ -38,14 +38,6 @@
};
};
- serial at 13820000 {
- status = "okay";
- };
-
- serial at 13830000 {
- status = "okay";
- };
-
gpio_keys {
pinctrl-0 = <&gpio_power_key &gpio_home_key>;
@@ -83,3 +75,11 @@
samsung,pin-pud = <0>;
};
};
+
+&serial_2 {
+ status = "okay";
+};
+
+&serial_3 {
+ status = "okay";
+};
--
2.1.4
next prev parent reply other threads:[~2015-05-17 8:12 UTC|newest]
Thread overview: 48+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-05-17 8:09 [PATCH v6 00/13] ARM: dts: exynos4: labels for overriding nodes Krzysztof Kozlowski
2015-05-17 8:09 ` Krzysztof Kozlowski
2015-05-17 8:09 ` Krzysztof Kozlowski
2015-05-17 8:09 ` [PATCH v6 01/13] ARM: dts: Add labels to exynos4 nodes Krzysztof Kozlowski
2015-05-17 8:09 ` Krzysztof Kozlowski
2015-05-17 8:09 ` [PATCH 1/4] ARM: multi_v7_defconfig: Enable CPU idle for Exynos Krzysztof Kozlowski
2015-05-17 8:09 ` Krzysztof Kozlowski
2015-05-17 8:09 ` [PATCH v6 02/13] ARM: dts: Use labels for overriding nodes in exynos4210 Krzysztof Kozlowski
2015-05-17 8:09 ` Krzysztof Kozlowski
2015-05-17 8:09 ` [PATCH 2/4] ARM: multi_v7_defconfig: Enable PMIC and MUIC drivers for Exynos boards Krzysztof Kozlowski
2015-05-17 8:09 ` Krzysztof Kozlowski
2015-05-17 8:09 ` [PATCH v6 03/13] ARM: dts: Use labels for overriding nodes in exynos4210-origen Krzysztof Kozlowski
2015-05-17 8:09 ` Krzysztof Kozlowski
2015-05-17 8:09 ` [PATCH 3/4] ARM: multi_v7_defconfig: Enable TMU for Exynos Krzysztof Kozlowski
2015-05-17 8:09 ` Krzysztof Kozlowski
2015-05-17 8:28 ` Krzysztof Kozłowski
2015-05-17 8:28 ` Krzysztof Kozłowski
2015-05-17 8:09 ` [PATCH v6 04/13] ARM: dts: Use labels for overriding nodes in exynos4210-smdkv310 Krzysztof Kozlowski
2015-05-17 8:09 ` Krzysztof Kozlowski
2015-05-17 8:09 ` [PATCH 4/4] ARM: multi_v7_defconfig: Enable OHCI on Exynos Krzysztof Kozlowski
2015-05-17 8:09 ` Krzysztof Kozlowski
2015-05-17 8:09 ` Krzysztof Kozlowski
2015-05-17 8:27 ` Krzysztof Kozłowski
2015-05-17 8:27 ` Krzysztof Kozłowski
2015-05-17 8:27 ` Krzysztof Kozłowski
2015-05-17 8:09 ` [PATCH v6 05/13] ARM: dts: Use labels for overriding nodes in exynos4210-trats Krzysztof Kozlowski
2015-05-17 8:09 ` Krzysztof Kozlowski
2015-05-17 8:09 ` [PATCH v6 06/13] ARM: dts: Use labels for overriding nodes in exynos4212 Krzysztof Kozlowski
2015-05-17 8:09 ` Krzysztof Kozlowski
2015-05-17 8:09 ` Krzysztof Kozlowski
2015-05-17 8:09 ` [PATCH v6 07/13] ARM: dts: Use labels for overriding nodes in exynos4x12 Krzysztof Kozlowski
2015-05-17 8:09 ` Krzysztof Kozlowski
2015-05-17 8:09 ` Krzysztof Kozlowski
2015-05-17 8:09 ` [PATCH v6 08/13] ARM: dts: Use labels for overriding nodes in exynos4412 Krzysztof Kozlowski
2015-05-17 8:09 ` Krzysztof Kozlowski
2015-05-17 8:09 ` Krzysztof Kozlowski
2015-05-17 8:09 ` Krzysztof Kozlowski [this message]
2015-05-17 8:09 ` [PATCH v6 09/13] ARM: dts: Use labels for overriding nodes in exynos4412-odroid Krzysztof Kozlowski
2015-05-17 8:30 ` [PATCH v6 10/13] ARM: dts: Use labels for overriding nodes in exynos4412-smdk4412 Krzysztof Kozlowski
2015-05-17 8:30 ` Krzysztof Kozlowski
2015-05-17 8:30 ` [PATCH v6 11/13] ARM: dts: Use labels for overriding nodes in exynos4412-trats2 Krzysztof Kozlowski
2015-05-17 8:30 ` Krzysztof Kozlowski
2015-05-17 8:30 ` [PATCH v6 12/13] ARM: dts: Use labels for overriding nodes in exynos4412-origen Krzysztof Kozlowski
2015-05-17 8:30 ` Krzysztof Kozlowski
2015-05-17 8:30 ` [PATCH v6 13/13] ARM: dts: Use labels for overriding nodes in exynos4412-tiny4412 Krzysztof Kozlowski
2015-05-17 8:30 ` Krzysztof Kozlowski
2015-05-23 3:58 ` [PATCH v6 00/13] ARM: dts: exynos4: labels for overriding nodes Kukjin Kim
2015-05-23 3:58 ` Kukjin Kim
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1431850195-9558-14-git-send-email-k.kozlowski.k@gmail.com \
--to=k.kozlowski.k@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=kgene@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.