All of lore.kernel.org
 help / color / mirror / Atom feed
From: Douglas Anderson <dianders@chromium.org>
To: ulf.hansson@linaro.org, Heiko Stuebner <heiko@sntech.de>
Cc: kishon@ti.com, robh+dt@kernel.org, shawn.lin@rock-chips.com,
	xzy.xu@rock-chips.com, briannorris@chromium.org,
	adrian.hunter@intel.com, linux-rockchip@lists.infradead.org,
	linux-mmc@vger.kernel.org, devicetree@vger.kernel.org,
	groeck@chromium.org, Douglas Anderson <dianders@chromium.org>,
	michal.simek@xilinx.com, soren.brinkmann@xilinx.com,
	linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org
Subject: [PATCH v3 08/15] mmc: sdhci-of-arasan: Properly set corecfg_baseclkfreq on rk3399
Date: Mon, 20 Jun 2016 10:56:47 -0700	[thread overview]
Message-ID: <1466445414-11974-9-git-send-email-dianders@chromium.org> (raw)
In-Reply-To: <1466445414-11974-1-git-send-email-dianders@chromium.org>

In the the earlier change in this series ("Documentation: mmc:
sdhci-of-arasan: Add soc-ctl-syscon for corecfg regs") we can see the
mechansim for specifying a syscon to properly set corecfg registers in
sdhci-of-arasan.  Now let's use this mechanism to properly set
corecfg_baseclkfreq on rk3399.

>From [1] the corecfg_baseclkfreq is supposed to be set to:
  Base Clock Frequency for SD Clock.
  This is the frequency of the xin_clk.

This is a relatively easy thing to do.  Note that we assume that xin_clk
is not dynamic and we can check the clock at probe time.  If any real
devices have a dynamic xin_clk future patches could register for
notifiers for the clock.

At the moment, setting corecfg_baseclkfreq is only supported for rk3399
since we need a specific map for each implementation.  The code is
written in a generic way that should make this easy to extend to other
SoCs.  Note that a specific compatible string for rk3399 is already in
use and so we add that to the table to match rk3399.

[1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
---
Changes in v3:
- Add collected tags

Changes in v2:
- Reorder includes (Shawn)

 drivers/mmc/host/sdhci-of-arasan.c | 189 ++++++++++++++++++++++++++++++++++---
 1 file changed, 178 insertions(+), 11 deletions(-)

diff --git a/drivers/mmc/host/sdhci-of-arasan.c b/drivers/mmc/host/sdhci-of-arasan.c
index 3ff1711077c2..1286fe8905dc 100644
--- a/drivers/mmc/host/sdhci-of-arasan.c
+++ b/drivers/mmc/host/sdhci-of-arasan.c
@@ -19,9 +19,11 @@
  * your option) any later version.
  */
 
+#include <linux/mfd/syscon.h>
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/phy/phy.h>
+#include <linux/regmap.h>
 #include "sdhci-pltfm.h"
 
 #define SDHCI_ARASAN_CLK_CTRL_OFFSET	0x2c
@@ -32,18 +34,115 @@
 #define CLK_CTRL_TIMEOUT_MASK		(0xf << CLK_CTRL_TIMEOUT_SHIFT)
 #define CLK_CTRL_TIMEOUT_MIN_EXP	13
 
+/*
+ * On some SoCs the syscon area has a feature where the upper 16-bits of
+ * each 32-bit register act as a write mask for the lower 16-bits.  This allows
+ * atomic updates of the register without locking.  This macro is used on SoCs
+ * that have that feature.
+ */
+#define HIWORD_UPDATE(val, mask, shift) \
+		((val) << (shift) | (mask) << ((shift) + 16))
+
+/**
+ * struct sdhci_arasan_soc_ctl_field - Field used in sdhci_arasan_soc_ctl_map
+ *
+ * @reg:	Offset within the syscon of the register containing this field
+ * @width:	Number of bits for this field
+ * @shift:	Bit offset within @reg of this field (or -1 if not avail)
+ */
+struct sdhci_arasan_soc_ctl_field {
+	u32 reg;
+	u16 width;
+	s16 shift;
+};
+
+/**
+ * struct sdhci_arasan_soc_ctl_map - Map in syscon to corecfg registers
+ *
+ * It's up to the licensee of the Arsan IP block to make these available
+ * somewhere if needed.  Presumably these will be scattered somewhere that's
+ * accessible via the syscon API.
+ *
+ * @baseclkfreq:	Where to find corecfg_baseclkfreq
+ * @hiword_update:	If true, use HIWORD_UPDATE to access the syscon
+ */
+struct sdhci_arasan_soc_ctl_map {
+	struct sdhci_arasan_soc_ctl_field	baseclkfreq;
+	bool					hiword_update;
+};
+
 /**
  * struct sdhci_arasan_data
- * @clk_ahb:	Pointer to the AHB clock
- * @phy:	Pointer to the generic phy
- * @phy_on:	True if the PHY is turned on.
+ * @clk_ahb:		Pointer to the AHB clock
+ * @phy:		Pointer to the generic phy
+ * @phy_on:		True if the PHY is turned on.
+ * @soc_ctl_base:	Pointer to regmap for syscon for soc_ctl registers.
+ * @soc_ctl_map:	Map to get offsets into soc_ctl registers.
  */
 struct sdhci_arasan_data {
 	struct clk	*clk_ahb;
 	struct phy	*phy;
 	bool		phy_on;
+
+	struct regmap	*soc_ctl_base;
+	const struct sdhci_arasan_soc_ctl_map *soc_ctl_map;
+};
+
+static const struct sdhci_arasan_soc_ctl_map rk3399_soc_ctl_map = {
+	.baseclkfreq = { .reg = 0xf000, .width = 8, .shift = 8 },
+	.hiword_update = true,
 };
 
+/**
+ * sdhci_arasan_syscon_write - Write to a field in soc_ctl registers
+ *
+ * This function allows writing to fields in sdhci_arasan_soc_ctl_map.
+ * Note that if a field is specified as not available (shift < 0) then
+ * this function will silently return an error code.  It will be noisy
+ * and print errors for any other (unexpected) errors.
+ *
+ * @host:	The sdhci_host
+ * @fld:	The field to write to
+ * @val:	The value to write
+ */
+static int sdhci_arasan_syscon_write(struct sdhci_host *host,
+				   const struct sdhci_arasan_soc_ctl_field *fld,
+				   u32 val)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
+	struct regmap *soc_ctl_base = sdhci_arasan->soc_ctl_base;
+	u32 reg = fld->reg;
+	u16 width = fld->width;
+	s16 shift = fld->shift;
+	int ret;
+
+	/*
+	 * Silently return errors for shift < 0 so caller doesn't have
+	 * to check for fields which are optional.  For fields that
+	 * are required then caller needs to do something special
+	 * anyway.
+	 */
+	if (shift < 0)
+		return -EINVAL;
+
+	if (sdhci_arasan->soc_ctl_map->hiword_update)
+		ret = regmap_write(soc_ctl_base, reg,
+				   HIWORD_UPDATE(val, GENMASK(width, 0),
+						 shift));
+	else
+		ret = regmap_update_bits(soc_ctl_base, reg,
+					 GENMASK(shift + width, shift),
+					 val << shift);
+
+	/* Yell about (unexpected) regmap errors */
+	if (ret)
+		pr_warn("%s: Regmap write fail: %d\n",
+			 mmc_hostname(host->mmc), ret);
+
+	return ret;
+}
+
 static unsigned int sdhci_arasan_get_timeout_clock(struct sdhci_host *host)
 {
 	u32 div;
@@ -191,9 +290,66 @@ static int sdhci_arasan_resume(struct device *dev)
 static SIMPLE_DEV_PM_OPS(sdhci_arasan_dev_pm_ops, sdhci_arasan_suspend,
 			 sdhci_arasan_resume);
 
+static const struct of_device_id sdhci_arasan_of_match[] = {
+	/* SoC-specific compatible strings w/ soc_ctl_map */
+	{
+		.compatible = "rockchip,rk3399-sdhci-5.1",
+		.data = &rk3399_soc_ctl_map,
+	},
+
+	/* Generic compatible below here */
+	{ .compatible = "arasan,sdhci-8.9a" },
+	{ .compatible = "arasan,sdhci-5.1" },
+	{ .compatible = "arasan,sdhci-4.9a" },
+
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, sdhci_arasan_of_match);
+
+/**
+ * sdhci_arasan_update_baseclkfreq - Set corecfg_baseclkfreq
+ *
+ * The corecfg_baseclkfreq is supposed to contain the MHz of clk_xin.  This
+ * function can be used to make that happen.
+ *
+ * NOTES:
+ * - Many existing devices don't seem to do this and work fine.  To keep
+ *   compatibility for old hardware where the device tree doesn't provide a
+ *   register map, this function is a noop if a soc_ctl_map hasn't been provided
+ *   for this platform.
+ * - It's assumed that clk_xin is not dynamic and that we use the SDHCI divider
+ *   to achieve lower clock rates.  That means that this function is called once
+ *   at probe time and never called again.
+ *
+ * @host:		The sdhci_host
+ */
+static void sdhci_arasan_update_baseclkfreq(struct sdhci_host *host)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
+	const struct sdhci_arasan_soc_ctl_map *soc_ctl_map =
+		sdhci_arasan->soc_ctl_map;
+	u32 mhz = DIV_ROUND_CLOSEST(clk_get_rate(pltfm_host->clk), 1000000);
+
+	/* Having a map is optional */
+	if (!soc_ctl_map)
+		return;
+
+	/* If we have a map, we expect to have a syscon */
+	if (!sdhci_arasan->soc_ctl_base) {
+		pr_warn("%s: Have regmap, but no soc-ctl-syscon\n",
+			mmc_hostname(host->mmc));
+		return;
+	}
+
+	sdhci_arasan_syscon_write(host, &soc_ctl_map->baseclkfreq, mhz);
+}
+
 static int sdhci_arasan_probe(struct platform_device *pdev)
 {
 	int ret;
+	const struct of_device_id *match;
+	struct device_node *node;
 	struct clk *clk_xin;
 	struct sdhci_host *host;
 	struct sdhci_pltfm_host *pltfm_host;
@@ -207,6 +363,23 @@ static int sdhci_arasan_probe(struct platform_device *pdev)
 	pltfm_host = sdhci_priv(host);
 	sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
 
+	match = of_match_node(sdhci_arasan_of_match, pdev->dev.of_node);
+	sdhci_arasan->soc_ctl_map = match->data;
+
+	node = of_parse_phandle(pdev->dev.of_node, "arasan,soc-ctl-syscon", 0);
+	if (node) {
+		sdhci_arasan->soc_ctl_base = syscon_node_to_regmap(node);
+		of_node_put(node);
+
+		if (IS_ERR(sdhci_arasan->soc_ctl_base)) {
+			ret = PTR_ERR(sdhci_arasan->soc_ctl_base);
+			if (ret != -EPROBE_DEFER)
+				dev_err(&pdev->dev, "Can't get syscon: %d\n",
+					ret);
+			goto err_pltfm_free;
+		}
+	}
+
 	sdhci_arasan->clk_ahb = devm_clk_get(&pdev->dev, "clk_ahb");
 	if (IS_ERR(sdhci_arasan->clk_ahb)) {
 		dev_err(&pdev->dev, "clk_ahb clock not found.\n");
@@ -236,6 +409,8 @@ static int sdhci_arasan_probe(struct platform_device *pdev)
 	sdhci_get_of_property(pdev);
 	pltfm_host->clk = clk_xin;
 
+	sdhci_arasan_update_baseclkfreq(host);
+
 	ret = mmc_of_parse(host->mmc);
 	if (ret) {
 		dev_err(&pdev->dev, "parsing dt failed (%u)\n", ret);
@@ -301,14 +476,6 @@ static int sdhci_arasan_remove(struct platform_device *pdev)
 	return ret;
 }
 
-static const struct of_device_id sdhci_arasan_of_match[] = {
-	{ .compatible = "arasan,sdhci-8.9a" },
-	{ .compatible = "arasan,sdhci-5.1" },
-	{ .compatible = "arasan,sdhci-4.9a" },
-	{ }
-};
-MODULE_DEVICE_TABLE(of, sdhci_arasan_of_match);
-
 static struct platform_driver sdhci_arasan_driver = {
 	.driver = {
 		.name = "sdhci-arasan",
-- 
2.8.0.rc3.226.g39d4020

WARNING: multiple messages have this Message-ID (diff)
From: Douglas Anderson <dianders-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>
To: ulf.hansson-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org,
	Heiko Stuebner <heiko-4mtYJXux2i+zQB+pC5nmwQ@public.gmane.org>
Cc: Douglas Anderson
	<dianders-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>,
	devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	xzy.xu-TNX95d0MmH7DzftRWevZcw@public.gmane.org,
	linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	shawn.lin-TNX95d0MmH7DzftRWevZcw@public.gmane.org,
	briannorris-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org,
	linux-mmc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	adrian.hunter-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org,
	kishon-l0cyMroinI0@public.gmane.org,
	linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
	robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
	linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
	groeck-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org,
	michal.simek-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org,
	soren.brinkmann-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org
Subject: [PATCH v3 08/15] mmc: sdhci-of-arasan: Properly set corecfg_baseclkfreq on rk3399
Date: Mon, 20 Jun 2016 10:56:47 -0700	[thread overview]
Message-ID: <1466445414-11974-9-git-send-email-dianders@chromium.org> (raw)
In-Reply-To: <1466445414-11974-1-git-send-email-dianders-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>

In the the earlier change in this series ("Documentation: mmc:
sdhci-of-arasan: Add soc-ctl-syscon for corecfg regs") we can see the
mechansim for specifying a syscon to properly set corecfg registers in
sdhci-of-arasan.  Now let's use this mechanism to properly set
corecfg_baseclkfreq on rk3399.

>From [1] the corecfg_baseclkfreq is supposed to be set to:
  Base Clock Frequency for SD Clock.
  This is the frequency of the xin_clk.

This is a relatively easy thing to do.  Note that we assume that xin_clk
is not dynamic and we can check the clock at probe time.  If any real
devices have a dynamic xin_clk future patches could register for
notifiers for the clock.

At the moment, setting corecfg_baseclkfreq is only supported for rk3399
since we need a specific map for each implementation.  The code is
written in a generic way that should make this easy to extend to other
SoCs.  Note that a specific compatible string for rk3399 is already in
use and so we add that to the table to match rk3399.

[1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf

Signed-off-by: Douglas Anderson <dianders-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>
Reviewed-by: Heiko Stuebner <heiko-4mtYJXux2i+zQB+pC5nmwQ@public.gmane.org>
Reviewed-by: Shawn Lin <shawn.lin-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
Tested-by: Heiko Stuebner <heiko-4mtYJXux2i+zQB+pC5nmwQ@public.gmane.org>
---
Changes in v3:
- Add collected tags

Changes in v2:
- Reorder includes (Shawn)

 drivers/mmc/host/sdhci-of-arasan.c | 189 ++++++++++++++++++++++++++++++++++---
 1 file changed, 178 insertions(+), 11 deletions(-)

diff --git a/drivers/mmc/host/sdhci-of-arasan.c b/drivers/mmc/host/sdhci-of-arasan.c
index 3ff1711077c2..1286fe8905dc 100644
--- a/drivers/mmc/host/sdhci-of-arasan.c
+++ b/drivers/mmc/host/sdhci-of-arasan.c
@@ -19,9 +19,11 @@
  * your option) any later version.
  */
 
+#include <linux/mfd/syscon.h>
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/phy/phy.h>
+#include <linux/regmap.h>
 #include "sdhci-pltfm.h"
 
 #define SDHCI_ARASAN_CLK_CTRL_OFFSET	0x2c
@@ -32,18 +34,115 @@
 #define CLK_CTRL_TIMEOUT_MASK		(0xf << CLK_CTRL_TIMEOUT_SHIFT)
 #define CLK_CTRL_TIMEOUT_MIN_EXP	13
 
+/*
+ * On some SoCs the syscon area has a feature where the upper 16-bits of
+ * each 32-bit register act as a write mask for the lower 16-bits.  This allows
+ * atomic updates of the register without locking.  This macro is used on SoCs
+ * that have that feature.
+ */
+#define HIWORD_UPDATE(val, mask, shift) \
+		((val) << (shift) | (mask) << ((shift) + 16))
+
+/**
+ * struct sdhci_arasan_soc_ctl_field - Field used in sdhci_arasan_soc_ctl_map
+ *
+ * @reg:	Offset within the syscon of the register containing this field
+ * @width:	Number of bits for this field
+ * @shift:	Bit offset within @reg of this field (or -1 if not avail)
+ */
+struct sdhci_arasan_soc_ctl_field {
+	u32 reg;
+	u16 width;
+	s16 shift;
+};
+
+/**
+ * struct sdhci_arasan_soc_ctl_map - Map in syscon to corecfg registers
+ *
+ * It's up to the licensee of the Arsan IP block to make these available
+ * somewhere if needed.  Presumably these will be scattered somewhere that's
+ * accessible via the syscon API.
+ *
+ * @baseclkfreq:	Where to find corecfg_baseclkfreq
+ * @hiword_update:	If true, use HIWORD_UPDATE to access the syscon
+ */
+struct sdhci_arasan_soc_ctl_map {
+	struct sdhci_arasan_soc_ctl_field	baseclkfreq;
+	bool					hiword_update;
+};
+
 /**
  * struct sdhci_arasan_data
- * @clk_ahb:	Pointer to the AHB clock
- * @phy:	Pointer to the generic phy
- * @phy_on:	True if the PHY is turned on.
+ * @clk_ahb:		Pointer to the AHB clock
+ * @phy:		Pointer to the generic phy
+ * @phy_on:		True if the PHY is turned on.
+ * @soc_ctl_base:	Pointer to regmap for syscon for soc_ctl registers.
+ * @soc_ctl_map:	Map to get offsets into soc_ctl registers.
  */
 struct sdhci_arasan_data {
 	struct clk	*clk_ahb;
 	struct phy	*phy;
 	bool		phy_on;
+
+	struct regmap	*soc_ctl_base;
+	const struct sdhci_arasan_soc_ctl_map *soc_ctl_map;
+};
+
+static const struct sdhci_arasan_soc_ctl_map rk3399_soc_ctl_map = {
+	.baseclkfreq = { .reg = 0xf000, .width = 8, .shift = 8 },
+	.hiword_update = true,
 };
 
+/**
+ * sdhci_arasan_syscon_write - Write to a field in soc_ctl registers
+ *
+ * This function allows writing to fields in sdhci_arasan_soc_ctl_map.
+ * Note that if a field is specified as not available (shift < 0) then
+ * this function will silently return an error code.  It will be noisy
+ * and print errors for any other (unexpected) errors.
+ *
+ * @host:	The sdhci_host
+ * @fld:	The field to write to
+ * @val:	The value to write
+ */
+static int sdhci_arasan_syscon_write(struct sdhci_host *host,
+				   const struct sdhci_arasan_soc_ctl_field *fld,
+				   u32 val)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
+	struct regmap *soc_ctl_base = sdhci_arasan->soc_ctl_base;
+	u32 reg = fld->reg;
+	u16 width = fld->width;
+	s16 shift = fld->shift;
+	int ret;
+
+	/*
+	 * Silently return errors for shift < 0 so caller doesn't have
+	 * to check for fields which are optional.  For fields that
+	 * are required then caller needs to do something special
+	 * anyway.
+	 */
+	if (shift < 0)
+		return -EINVAL;
+
+	if (sdhci_arasan->soc_ctl_map->hiword_update)
+		ret = regmap_write(soc_ctl_base, reg,
+				   HIWORD_UPDATE(val, GENMASK(width, 0),
+						 shift));
+	else
+		ret = regmap_update_bits(soc_ctl_base, reg,
+					 GENMASK(shift + width, shift),
+					 val << shift);
+
+	/* Yell about (unexpected) regmap errors */
+	if (ret)
+		pr_warn("%s: Regmap write fail: %d\n",
+			 mmc_hostname(host->mmc), ret);
+
+	return ret;
+}
+
 static unsigned int sdhci_arasan_get_timeout_clock(struct sdhci_host *host)
 {
 	u32 div;
@@ -191,9 +290,66 @@ static int sdhci_arasan_resume(struct device *dev)
 static SIMPLE_DEV_PM_OPS(sdhci_arasan_dev_pm_ops, sdhci_arasan_suspend,
 			 sdhci_arasan_resume);
 
+static const struct of_device_id sdhci_arasan_of_match[] = {
+	/* SoC-specific compatible strings w/ soc_ctl_map */
+	{
+		.compatible = "rockchip,rk3399-sdhci-5.1",
+		.data = &rk3399_soc_ctl_map,
+	},
+
+	/* Generic compatible below here */
+	{ .compatible = "arasan,sdhci-8.9a" },
+	{ .compatible = "arasan,sdhci-5.1" },
+	{ .compatible = "arasan,sdhci-4.9a" },
+
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, sdhci_arasan_of_match);
+
+/**
+ * sdhci_arasan_update_baseclkfreq - Set corecfg_baseclkfreq
+ *
+ * The corecfg_baseclkfreq is supposed to contain the MHz of clk_xin.  This
+ * function can be used to make that happen.
+ *
+ * NOTES:
+ * - Many existing devices don't seem to do this and work fine.  To keep
+ *   compatibility for old hardware where the device tree doesn't provide a
+ *   register map, this function is a noop if a soc_ctl_map hasn't been provided
+ *   for this platform.
+ * - It's assumed that clk_xin is not dynamic and that we use the SDHCI divider
+ *   to achieve lower clock rates.  That means that this function is called once
+ *   at probe time and never called again.
+ *
+ * @host:		The sdhci_host
+ */
+static void sdhci_arasan_update_baseclkfreq(struct sdhci_host *host)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
+	const struct sdhci_arasan_soc_ctl_map *soc_ctl_map =
+		sdhci_arasan->soc_ctl_map;
+	u32 mhz = DIV_ROUND_CLOSEST(clk_get_rate(pltfm_host->clk), 1000000);
+
+	/* Having a map is optional */
+	if (!soc_ctl_map)
+		return;
+
+	/* If we have a map, we expect to have a syscon */
+	if (!sdhci_arasan->soc_ctl_base) {
+		pr_warn("%s: Have regmap, but no soc-ctl-syscon\n",
+			mmc_hostname(host->mmc));
+		return;
+	}
+
+	sdhci_arasan_syscon_write(host, &soc_ctl_map->baseclkfreq, mhz);
+}
+
 static int sdhci_arasan_probe(struct platform_device *pdev)
 {
 	int ret;
+	const struct of_device_id *match;
+	struct device_node *node;
 	struct clk *clk_xin;
 	struct sdhci_host *host;
 	struct sdhci_pltfm_host *pltfm_host;
@@ -207,6 +363,23 @@ static int sdhci_arasan_probe(struct platform_device *pdev)
 	pltfm_host = sdhci_priv(host);
 	sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
 
+	match = of_match_node(sdhci_arasan_of_match, pdev->dev.of_node);
+	sdhci_arasan->soc_ctl_map = match->data;
+
+	node = of_parse_phandle(pdev->dev.of_node, "arasan,soc-ctl-syscon", 0);
+	if (node) {
+		sdhci_arasan->soc_ctl_base = syscon_node_to_regmap(node);
+		of_node_put(node);
+
+		if (IS_ERR(sdhci_arasan->soc_ctl_base)) {
+			ret = PTR_ERR(sdhci_arasan->soc_ctl_base);
+			if (ret != -EPROBE_DEFER)
+				dev_err(&pdev->dev, "Can't get syscon: %d\n",
+					ret);
+			goto err_pltfm_free;
+		}
+	}
+
 	sdhci_arasan->clk_ahb = devm_clk_get(&pdev->dev, "clk_ahb");
 	if (IS_ERR(sdhci_arasan->clk_ahb)) {
 		dev_err(&pdev->dev, "clk_ahb clock not found.\n");
@@ -236,6 +409,8 @@ static int sdhci_arasan_probe(struct platform_device *pdev)
 	sdhci_get_of_property(pdev);
 	pltfm_host->clk = clk_xin;
 
+	sdhci_arasan_update_baseclkfreq(host);
+
 	ret = mmc_of_parse(host->mmc);
 	if (ret) {
 		dev_err(&pdev->dev, "parsing dt failed (%u)\n", ret);
@@ -301,14 +476,6 @@ static int sdhci_arasan_remove(struct platform_device *pdev)
 	return ret;
 }
 
-static const struct of_device_id sdhci_arasan_of_match[] = {
-	{ .compatible = "arasan,sdhci-8.9a" },
-	{ .compatible = "arasan,sdhci-5.1" },
-	{ .compatible = "arasan,sdhci-4.9a" },
-	{ }
-};
-MODULE_DEVICE_TABLE(of, sdhci_arasan_of_match);
-
 static struct platform_driver sdhci_arasan_driver = {
 	.driver = {
 		.name = "sdhci-arasan",
-- 
2.8.0.rc3.226.g39d4020

WARNING: multiple messages have this Message-ID (diff)
From: Douglas Anderson <dianders-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>
To: ulf.hansson-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org,
	Heiko Stuebner <heiko-4mtYJXux2i+zQB+pC5nmwQ@public.gmane.org>
Cc: Douglas Anderson
	<dianders-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>,
	devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	xzy.xu-TNX95d0MmH7DzftRWevZcw@public.gmane.org,
	linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	shawn.lin-TNX95d0MmH7DzftRWevZcw@public.gmane.org,
	briannorris-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org,
	linux-mmc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	adrian.hunter-ral2JQCrhuEAvxtiuMwx3w@public.gmane.org,
	kishon-l0cyMroinI0@public.gmane.org,
	linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
	robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
	linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
	groeck-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org,
	michal.simek-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org,
	soren.brinkmann-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org
Subject: [PATCH v3 08/15] mmc: sdhci-of-arasan: Properly set corecfg_baseclkfreq on rk3399
Date: Mon, 20 Jun 2016 10:56:47 -0700	[thread overview]
Message-ID: <1466445414-11974-9-git-send-email-dianders@chromium.org> (raw)
In-Reply-To: <1466445414-11974-1-git-send-email-dianders-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>

In the the earlier change in this series ("Documentation: mmc:
sdhci-of-arasan: Add soc-ctl-syscon for corecfg regs") we can see the
mechansim for specifying a syscon to properly set corecfg registers in
sdhci-of-arasan.  Now let's use this mechanism to properly set
corecfg_baseclkfreq on rk3399.

From [1] the corecfg_baseclkfreq is supposed to be set to:
  Base Clock Frequency for SD Clock.
  This is the frequency of the xin_clk.

This is a relatively easy thing to do.  Note that we assume that xin_clk
is not dynamic and we can check the clock at probe time.  If any real
devices have a dynamic xin_clk future patches could register for
notifiers for the clock.

At the moment, setting corecfg_baseclkfreq is only supported for rk3399
since we need a specific map for each implementation.  The code is
written in a generic way that should make this easy to extend to other
SoCs.  Note that a specific compatible string for rk3399 is already in
use and so we add that to the table to match rk3399.

[1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf

Signed-off-by: Douglas Anderson <dianders-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>
Reviewed-by: Heiko Stuebner <heiko-4mtYJXux2i+zQB+pC5nmwQ@public.gmane.org>
Reviewed-by: Shawn Lin <shawn.lin-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
Tested-by: Heiko Stuebner <heiko-4mtYJXux2i+zQB+pC5nmwQ@public.gmane.org>
---
Changes in v3:
- Add collected tags

Changes in v2:
- Reorder includes (Shawn)

 drivers/mmc/host/sdhci-of-arasan.c | 189 ++++++++++++++++++++++++++++++++++---
 1 file changed, 178 insertions(+), 11 deletions(-)

diff --git a/drivers/mmc/host/sdhci-of-arasan.c b/drivers/mmc/host/sdhci-of-arasan.c
index 3ff1711077c2..1286fe8905dc 100644
--- a/drivers/mmc/host/sdhci-of-arasan.c
+++ b/drivers/mmc/host/sdhci-of-arasan.c
@@ -19,9 +19,11 @@
  * your option) any later version.
  */
 
+#include <linux/mfd/syscon.h>
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/phy/phy.h>
+#include <linux/regmap.h>
 #include "sdhci-pltfm.h"
 
 #define SDHCI_ARASAN_CLK_CTRL_OFFSET	0x2c
@@ -32,18 +34,115 @@
 #define CLK_CTRL_TIMEOUT_MASK		(0xf << CLK_CTRL_TIMEOUT_SHIFT)
 #define CLK_CTRL_TIMEOUT_MIN_EXP	13
 
+/*
+ * On some SoCs the syscon area has a feature where the upper 16-bits of
+ * each 32-bit register act as a write mask for the lower 16-bits.  This allows
+ * atomic updates of the register without locking.  This macro is used on SoCs
+ * that have that feature.
+ */
+#define HIWORD_UPDATE(val, mask, shift) \
+		((val) << (shift) | (mask) << ((shift) + 16))
+
+/**
+ * struct sdhci_arasan_soc_ctl_field - Field used in sdhci_arasan_soc_ctl_map
+ *
+ * @reg:	Offset within the syscon of the register containing this field
+ * @width:	Number of bits for this field
+ * @shift:	Bit offset within @reg of this field (or -1 if not avail)
+ */
+struct sdhci_arasan_soc_ctl_field {
+	u32 reg;
+	u16 width;
+	s16 shift;
+};
+
+/**
+ * struct sdhci_arasan_soc_ctl_map - Map in syscon to corecfg registers
+ *
+ * It's up to the licensee of the Arsan IP block to make these available
+ * somewhere if needed.  Presumably these will be scattered somewhere that's
+ * accessible via the syscon API.
+ *
+ * @baseclkfreq:	Where to find corecfg_baseclkfreq
+ * @hiword_update:	If true, use HIWORD_UPDATE to access the syscon
+ */
+struct sdhci_arasan_soc_ctl_map {
+	struct sdhci_arasan_soc_ctl_field	baseclkfreq;
+	bool					hiword_update;
+};
+
 /**
  * struct sdhci_arasan_data
- * @clk_ahb:	Pointer to the AHB clock
- * @phy:	Pointer to the generic phy
- * @phy_on:	True if the PHY is turned on.
+ * @clk_ahb:		Pointer to the AHB clock
+ * @phy:		Pointer to the generic phy
+ * @phy_on:		True if the PHY is turned on.
+ * @soc_ctl_base:	Pointer to regmap for syscon for soc_ctl registers.
+ * @soc_ctl_map:	Map to get offsets into soc_ctl registers.
  */
 struct sdhci_arasan_data {
 	struct clk	*clk_ahb;
 	struct phy	*phy;
 	bool		phy_on;
+
+	struct regmap	*soc_ctl_base;
+	const struct sdhci_arasan_soc_ctl_map *soc_ctl_map;
+};
+
+static const struct sdhci_arasan_soc_ctl_map rk3399_soc_ctl_map = {
+	.baseclkfreq = { .reg = 0xf000, .width = 8, .shift = 8 },
+	.hiword_update = true,
 };
 
+/**
+ * sdhci_arasan_syscon_write - Write to a field in soc_ctl registers
+ *
+ * This function allows writing to fields in sdhci_arasan_soc_ctl_map.
+ * Note that if a field is specified as not available (shift < 0) then
+ * this function will silently return an error code.  It will be noisy
+ * and print errors for any other (unexpected) errors.
+ *
+ * @host:	The sdhci_host
+ * @fld:	The field to write to
+ * @val:	The value to write
+ */
+static int sdhci_arasan_syscon_write(struct sdhci_host *host,
+				   const struct sdhci_arasan_soc_ctl_field *fld,
+				   u32 val)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
+	struct regmap *soc_ctl_base = sdhci_arasan->soc_ctl_base;
+	u32 reg = fld->reg;
+	u16 width = fld->width;
+	s16 shift = fld->shift;
+	int ret;
+
+	/*
+	 * Silently return errors for shift < 0 so caller doesn't have
+	 * to check for fields which are optional.  For fields that
+	 * are required then caller needs to do something special
+	 * anyway.
+	 */
+	if (shift < 0)
+		return -EINVAL;
+
+	if (sdhci_arasan->soc_ctl_map->hiword_update)
+		ret = regmap_write(soc_ctl_base, reg,
+				   HIWORD_UPDATE(val, GENMASK(width, 0),
+						 shift));
+	else
+		ret = regmap_update_bits(soc_ctl_base, reg,
+					 GENMASK(shift + width, shift),
+					 val << shift);
+
+	/* Yell about (unexpected) regmap errors */
+	if (ret)
+		pr_warn("%s: Regmap write fail: %d\n",
+			 mmc_hostname(host->mmc), ret);
+
+	return ret;
+}
+
 static unsigned int sdhci_arasan_get_timeout_clock(struct sdhci_host *host)
 {
 	u32 div;
@@ -191,9 +290,66 @@ static int sdhci_arasan_resume(struct device *dev)
 static SIMPLE_DEV_PM_OPS(sdhci_arasan_dev_pm_ops, sdhci_arasan_suspend,
 			 sdhci_arasan_resume);
 
+static const struct of_device_id sdhci_arasan_of_match[] = {
+	/* SoC-specific compatible strings w/ soc_ctl_map */
+	{
+		.compatible = "rockchip,rk3399-sdhci-5.1",
+		.data = &rk3399_soc_ctl_map,
+	},
+
+	/* Generic compatible below here */
+	{ .compatible = "arasan,sdhci-8.9a" },
+	{ .compatible = "arasan,sdhci-5.1" },
+	{ .compatible = "arasan,sdhci-4.9a" },
+
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, sdhci_arasan_of_match);
+
+/**
+ * sdhci_arasan_update_baseclkfreq - Set corecfg_baseclkfreq
+ *
+ * The corecfg_baseclkfreq is supposed to contain the MHz of clk_xin.  This
+ * function can be used to make that happen.
+ *
+ * NOTES:
+ * - Many existing devices don't seem to do this and work fine.  To keep
+ *   compatibility for old hardware where the device tree doesn't provide a
+ *   register map, this function is a noop if a soc_ctl_map hasn't been provided
+ *   for this platform.
+ * - It's assumed that clk_xin is not dynamic and that we use the SDHCI divider
+ *   to achieve lower clock rates.  That means that this function is called once
+ *   at probe time and never called again.
+ *
+ * @host:		The sdhci_host
+ */
+static void sdhci_arasan_update_baseclkfreq(struct sdhci_host *host)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
+	const struct sdhci_arasan_soc_ctl_map *soc_ctl_map =
+		sdhci_arasan->soc_ctl_map;
+	u32 mhz = DIV_ROUND_CLOSEST(clk_get_rate(pltfm_host->clk), 1000000);
+
+	/* Having a map is optional */
+	if (!soc_ctl_map)
+		return;
+
+	/* If we have a map, we expect to have a syscon */
+	if (!sdhci_arasan->soc_ctl_base) {
+		pr_warn("%s: Have regmap, but no soc-ctl-syscon\n",
+			mmc_hostname(host->mmc));
+		return;
+	}
+
+	sdhci_arasan_syscon_write(host, &soc_ctl_map->baseclkfreq, mhz);
+}
+
 static int sdhci_arasan_probe(struct platform_device *pdev)
 {
 	int ret;
+	const struct of_device_id *match;
+	struct device_node *node;
 	struct clk *clk_xin;
 	struct sdhci_host *host;
 	struct sdhci_pltfm_host *pltfm_host;
@@ -207,6 +363,23 @@ static int sdhci_arasan_probe(struct platform_device *pdev)
 	pltfm_host = sdhci_priv(host);
 	sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
 
+	match = of_match_node(sdhci_arasan_of_match, pdev->dev.of_node);
+	sdhci_arasan->soc_ctl_map = match->data;
+
+	node = of_parse_phandle(pdev->dev.of_node, "arasan,soc-ctl-syscon", 0);
+	if (node) {
+		sdhci_arasan->soc_ctl_base = syscon_node_to_regmap(node);
+		of_node_put(node);
+
+		if (IS_ERR(sdhci_arasan->soc_ctl_base)) {
+			ret = PTR_ERR(sdhci_arasan->soc_ctl_base);
+			if (ret != -EPROBE_DEFER)
+				dev_err(&pdev->dev, "Can't get syscon: %d\n",
+					ret);
+			goto err_pltfm_free;
+		}
+	}
+
 	sdhci_arasan->clk_ahb = devm_clk_get(&pdev->dev, "clk_ahb");
 	if (IS_ERR(sdhci_arasan->clk_ahb)) {
 		dev_err(&pdev->dev, "clk_ahb clock not found.\n");
@@ -236,6 +409,8 @@ static int sdhci_arasan_probe(struct platform_device *pdev)
 	sdhci_get_of_property(pdev);
 	pltfm_host->clk = clk_xin;
 
+	sdhci_arasan_update_baseclkfreq(host);
+
 	ret = mmc_of_parse(host->mmc);
 	if (ret) {
 		dev_err(&pdev->dev, "parsing dt failed (%u)\n", ret);
@@ -301,14 +476,6 @@ static int sdhci_arasan_remove(struct platform_device *pdev)
 	return ret;
 }
 
-static const struct of_device_id sdhci_arasan_of_match[] = {
-	{ .compatible = "arasan,sdhci-8.9a" },
-	{ .compatible = "arasan,sdhci-5.1" },
-	{ .compatible = "arasan,sdhci-4.9a" },
-	{ }
-};
-MODULE_DEVICE_TABLE(of, sdhci_arasan_of_match);
-
 static struct platform_driver sdhci_arasan_driver = {
 	.driver = {
 		.name = "sdhci-arasan",
-- 
2.8.0.rc3.226.g39d4020

WARNING: multiple messages have this Message-ID (diff)
From: dianders@chromium.org (Douglas Anderson)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v3 08/15] mmc: sdhci-of-arasan: Properly set corecfg_baseclkfreq on rk3399
Date: Mon, 20 Jun 2016 10:56:47 -0700	[thread overview]
Message-ID: <1466445414-11974-9-git-send-email-dianders@chromium.org> (raw)
In-Reply-To: <1466445414-11974-1-git-send-email-dianders@chromium.org>

In the the earlier change in this series ("Documentation: mmc:
sdhci-of-arasan: Add soc-ctl-syscon for corecfg regs") we can see the
mechansim for specifying a syscon to properly set corecfg registers in
sdhci-of-arasan.  Now let's use this mechanism to properly set
corecfg_baseclkfreq on rk3399.

>From [1] the corecfg_baseclkfreq is supposed to be set to:
  Base Clock Frequency for SD Clock.
  This is the frequency of the xin_clk.

This is a relatively easy thing to do.  Note that we assume that xin_clk
is not dynamic and we can check the clock at probe time.  If any real
devices have a dynamic xin_clk future patches could register for
notifiers for the clock.

At the moment, setting corecfg_baseclkfreq is only supported for rk3399
since we need a specific map for each implementation.  The code is
written in a generic way that should make this easy to extend to other
SoCs.  Note that a specific compatible string for rk3399 is already in
use and so we add that to the table to match rk3399.

[1]: https://arasan.com/wp-content/media/eMMC-5-1-Total-Solution_Rev-1-3.pdf

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
---
Changes in v3:
- Add collected tags

Changes in v2:
- Reorder includes (Shawn)

 drivers/mmc/host/sdhci-of-arasan.c | 189 ++++++++++++++++++++++++++++++++++---
 1 file changed, 178 insertions(+), 11 deletions(-)

diff --git a/drivers/mmc/host/sdhci-of-arasan.c b/drivers/mmc/host/sdhci-of-arasan.c
index 3ff1711077c2..1286fe8905dc 100644
--- a/drivers/mmc/host/sdhci-of-arasan.c
+++ b/drivers/mmc/host/sdhci-of-arasan.c
@@ -19,9 +19,11 @@
  * your option) any later version.
  */
 
+#include <linux/mfd/syscon.h>
 #include <linux/module.h>
 #include <linux/of_device.h>
 #include <linux/phy/phy.h>
+#include <linux/regmap.h>
 #include "sdhci-pltfm.h"
 
 #define SDHCI_ARASAN_CLK_CTRL_OFFSET	0x2c
@@ -32,18 +34,115 @@
 #define CLK_CTRL_TIMEOUT_MASK		(0xf << CLK_CTRL_TIMEOUT_SHIFT)
 #define CLK_CTRL_TIMEOUT_MIN_EXP	13
 
+/*
+ * On some SoCs the syscon area has a feature where the upper 16-bits of
+ * each 32-bit register act as a write mask for the lower 16-bits.  This allows
+ * atomic updates of the register without locking.  This macro is used on SoCs
+ * that have that feature.
+ */
+#define HIWORD_UPDATE(val, mask, shift) \
+		((val) << (shift) | (mask) << ((shift) + 16))
+
+/**
+ * struct sdhci_arasan_soc_ctl_field - Field used in sdhci_arasan_soc_ctl_map
+ *
+ * @reg:	Offset within the syscon of the register containing this field
+ * @width:	Number of bits for this field
+ * @shift:	Bit offset within @reg of this field (or -1 if not avail)
+ */
+struct sdhci_arasan_soc_ctl_field {
+	u32 reg;
+	u16 width;
+	s16 shift;
+};
+
+/**
+ * struct sdhci_arasan_soc_ctl_map - Map in syscon to corecfg registers
+ *
+ * It's up to the licensee of the Arsan IP block to make these available
+ * somewhere if needed.  Presumably these will be scattered somewhere that's
+ * accessible via the syscon API.
+ *
+ * @baseclkfreq:	Where to find corecfg_baseclkfreq
+ * @hiword_update:	If true, use HIWORD_UPDATE to access the syscon
+ */
+struct sdhci_arasan_soc_ctl_map {
+	struct sdhci_arasan_soc_ctl_field	baseclkfreq;
+	bool					hiword_update;
+};
+
 /**
  * struct sdhci_arasan_data
- * @clk_ahb:	Pointer to the AHB clock
- * @phy:	Pointer to the generic phy
- * @phy_on:	True if the PHY is turned on.
+ * @clk_ahb:		Pointer to the AHB clock
+ * @phy:		Pointer to the generic phy
+ * @phy_on:		True if the PHY is turned on.
+ * @soc_ctl_base:	Pointer to regmap for syscon for soc_ctl registers.
+ * @soc_ctl_map:	Map to get offsets into soc_ctl registers.
  */
 struct sdhci_arasan_data {
 	struct clk	*clk_ahb;
 	struct phy	*phy;
 	bool		phy_on;
+
+	struct regmap	*soc_ctl_base;
+	const struct sdhci_arasan_soc_ctl_map *soc_ctl_map;
+};
+
+static const struct sdhci_arasan_soc_ctl_map rk3399_soc_ctl_map = {
+	.baseclkfreq = { .reg = 0xf000, .width = 8, .shift = 8 },
+	.hiword_update = true,
 };
 
+/**
+ * sdhci_arasan_syscon_write - Write to a field in soc_ctl registers
+ *
+ * This function allows writing to fields in sdhci_arasan_soc_ctl_map.
+ * Note that if a field is specified as not available (shift < 0) then
+ * this function will silently return an error code.  It will be noisy
+ * and print errors for any other (unexpected) errors.
+ *
+ * @host:	The sdhci_host
+ * @fld:	The field to write to
+ * @val:	The value to write
+ */
+static int sdhci_arasan_syscon_write(struct sdhci_host *host,
+				   const struct sdhci_arasan_soc_ctl_field *fld,
+				   u32 val)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
+	struct regmap *soc_ctl_base = sdhci_arasan->soc_ctl_base;
+	u32 reg = fld->reg;
+	u16 width = fld->width;
+	s16 shift = fld->shift;
+	int ret;
+
+	/*
+	 * Silently return errors for shift < 0 so caller doesn't have
+	 * to check for fields which are optional.  For fields that
+	 * are required then caller needs to do something special
+	 * anyway.
+	 */
+	if (shift < 0)
+		return -EINVAL;
+
+	if (sdhci_arasan->soc_ctl_map->hiword_update)
+		ret = regmap_write(soc_ctl_base, reg,
+				   HIWORD_UPDATE(val, GENMASK(width, 0),
+						 shift));
+	else
+		ret = regmap_update_bits(soc_ctl_base, reg,
+					 GENMASK(shift + width, shift),
+					 val << shift);
+
+	/* Yell about (unexpected) regmap errors */
+	if (ret)
+		pr_warn("%s: Regmap write fail: %d\n",
+			 mmc_hostname(host->mmc), ret);
+
+	return ret;
+}
+
 static unsigned int sdhci_arasan_get_timeout_clock(struct sdhci_host *host)
 {
 	u32 div;
@@ -191,9 +290,66 @@ static int sdhci_arasan_resume(struct device *dev)
 static SIMPLE_DEV_PM_OPS(sdhci_arasan_dev_pm_ops, sdhci_arasan_suspend,
 			 sdhci_arasan_resume);
 
+static const struct of_device_id sdhci_arasan_of_match[] = {
+	/* SoC-specific compatible strings w/ soc_ctl_map */
+	{
+		.compatible = "rockchip,rk3399-sdhci-5.1",
+		.data = &rk3399_soc_ctl_map,
+	},
+
+	/* Generic compatible below here */
+	{ .compatible = "arasan,sdhci-8.9a" },
+	{ .compatible = "arasan,sdhci-5.1" },
+	{ .compatible = "arasan,sdhci-4.9a" },
+
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, sdhci_arasan_of_match);
+
+/**
+ * sdhci_arasan_update_baseclkfreq - Set corecfg_baseclkfreq
+ *
+ * The corecfg_baseclkfreq is supposed to contain the MHz of clk_xin.  This
+ * function can be used to make that happen.
+ *
+ * NOTES:
+ * - Many existing devices don't seem to do this and work fine.  To keep
+ *   compatibility for old hardware where the device tree doesn't provide a
+ *   register map, this function is a noop if a soc_ctl_map hasn't been provided
+ *   for this platform.
+ * - It's assumed that clk_xin is not dynamic and that we use the SDHCI divider
+ *   to achieve lower clock rates.  That means that this function is called once
+ *   at probe time and never called again.
+ *
+ * @host:		The sdhci_host
+ */
+static void sdhci_arasan_update_baseclkfreq(struct sdhci_host *host)
+{
+	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+	struct sdhci_arasan_data *sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
+	const struct sdhci_arasan_soc_ctl_map *soc_ctl_map =
+		sdhci_arasan->soc_ctl_map;
+	u32 mhz = DIV_ROUND_CLOSEST(clk_get_rate(pltfm_host->clk), 1000000);
+
+	/* Having a map is optional */
+	if (!soc_ctl_map)
+		return;
+
+	/* If we have a map, we expect to have a syscon */
+	if (!sdhci_arasan->soc_ctl_base) {
+		pr_warn("%s: Have regmap, but no soc-ctl-syscon\n",
+			mmc_hostname(host->mmc));
+		return;
+	}
+
+	sdhci_arasan_syscon_write(host, &soc_ctl_map->baseclkfreq, mhz);
+}
+
 static int sdhci_arasan_probe(struct platform_device *pdev)
 {
 	int ret;
+	const struct of_device_id *match;
+	struct device_node *node;
 	struct clk *clk_xin;
 	struct sdhci_host *host;
 	struct sdhci_pltfm_host *pltfm_host;
@@ -207,6 +363,23 @@ static int sdhci_arasan_probe(struct platform_device *pdev)
 	pltfm_host = sdhci_priv(host);
 	sdhci_arasan = sdhci_pltfm_priv(pltfm_host);
 
+	match = of_match_node(sdhci_arasan_of_match, pdev->dev.of_node);
+	sdhci_arasan->soc_ctl_map = match->data;
+
+	node = of_parse_phandle(pdev->dev.of_node, "arasan,soc-ctl-syscon", 0);
+	if (node) {
+		sdhci_arasan->soc_ctl_base = syscon_node_to_regmap(node);
+		of_node_put(node);
+
+		if (IS_ERR(sdhci_arasan->soc_ctl_base)) {
+			ret = PTR_ERR(sdhci_arasan->soc_ctl_base);
+			if (ret != -EPROBE_DEFER)
+				dev_err(&pdev->dev, "Can't get syscon: %d\n",
+					ret);
+			goto err_pltfm_free;
+		}
+	}
+
 	sdhci_arasan->clk_ahb = devm_clk_get(&pdev->dev, "clk_ahb");
 	if (IS_ERR(sdhci_arasan->clk_ahb)) {
 		dev_err(&pdev->dev, "clk_ahb clock not found.\n");
@@ -236,6 +409,8 @@ static int sdhci_arasan_probe(struct platform_device *pdev)
 	sdhci_get_of_property(pdev);
 	pltfm_host->clk = clk_xin;
 
+	sdhci_arasan_update_baseclkfreq(host);
+
 	ret = mmc_of_parse(host->mmc);
 	if (ret) {
 		dev_err(&pdev->dev, "parsing dt failed (%u)\n", ret);
@@ -301,14 +476,6 @@ static int sdhci_arasan_remove(struct platform_device *pdev)
 	return ret;
 }
 
-static const struct of_device_id sdhci_arasan_of_match[] = {
-	{ .compatible = "arasan,sdhci-8.9a" },
-	{ .compatible = "arasan,sdhci-5.1" },
-	{ .compatible = "arasan,sdhci-4.9a" },
-	{ }
-};
-MODULE_DEVICE_TABLE(of, sdhci_arasan_of_match);
-
 static struct platform_driver sdhci_arasan_driver = {
 	.driver = {
 		.name = "sdhci-arasan",
-- 
2.8.0.rc3.226.g39d4020

  parent reply	other threads:[~2016-06-20 18:10 UTC|newest]

Thread overview: 87+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-06-20 17:56 [PATCH v3 0/15] Changes to support 150 MHz eMMC on rk3399 Douglas Anderson
2016-06-20 17:56 ` Douglas Anderson
2016-06-20 17:56 ` Douglas Anderson
2016-06-20 17:56 ` [PATCH v3 01/15] phy: rockchip-emmc: give DLL some extra time to be ready Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 19:23   ` Guenter Roeck
2016-06-20 19:23     ` Guenter Roeck
2016-06-20 19:23     ` Guenter Roeck
2016-06-20 19:30     ` Doug Anderson
2016-06-20 19:30       ` Doug Anderson
2016-06-20 19:30       ` Doug Anderson
2016-06-20 19:36       ` Guenter Roeck
2016-06-20 19:36         ` Guenter Roeck
2016-06-20 19:36         ` Guenter Roeck
2016-06-20 19:38         ` Doug Anderson
2016-06-20 19:38           ` Doug Anderson
2016-06-20 19:38           ` Doug Anderson
2016-06-20 17:56 ` [PATCH v3 02/15] phy: rockchip-emmc: configure frequency range and drive impedance Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56 ` [PATCH v3 03/15] phy: rockchip-emmc: configure default output tap delay Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56 ` [PATCH v3 04/15] phy: rockchip-emmc: reindent the register definitions Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56 ` [PATCH v3 05/15] phy: rockchip-emmc: Increase lock time allowance Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 19:29   ` Guenter Roeck
2016-06-20 19:29     ` Guenter Roeck
2016-06-20 19:29     ` Guenter Roeck
2016-06-20 19:36     ` Doug Anderson
2016-06-20 19:36       ` Doug Anderson
2016-06-20 19:36       ` Doug Anderson
2016-06-20 19:38       ` Guenter Roeck
2016-06-20 19:38         ` Guenter Roeck
2016-06-20 19:38         ` Guenter Roeck
2016-06-20 17:56 ` [PATCH v3 06/15] mmc: sdhci-of-arasan: Always power the PHY off/on when clock changes Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-22 12:34   ` Adrian Hunter
2016-06-22 12:34     ` Adrian Hunter
2016-06-22 12:34     ` Adrian Hunter
2016-06-20 17:56 ` [PATCH v3 07/15] Documentation: mmc: sdhci-of-arasan: Add soc-ctl-syscon for corecfg regs Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56 ` Douglas Anderson [this message]
2016-06-20 17:56   ` [PATCH v3 08/15] mmc: sdhci-of-arasan: Properly set corecfg_baseclkfreq on rk3399 Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-22 12:34   ` Adrian Hunter
2016-06-22 12:34     ` Adrian Hunter
2016-06-20 17:56 ` [PATCH v3 09/15] arm64: dts: rockchip: Add soc-ctl-syscon to sdhci for rk3399 Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-22 16:30   ` Heiko Stübner
2016-06-22 16:30     ` Heiko Stübner
2016-06-20 17:56 ` [PATCH v3 10/15] Documentation: mmc: sdhci-of-arasan: Add ability to export card clock Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56 ` [PATCH v3 11/15] " Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-22 12:35   ` Adrian Hunter
2016-06-22 12:35     ` Adrian Hunter
2016-06-20 17:56 ` [PATCH v3 12/15] Documentation: phy: Let the rockchip eMMC PHY get an exported " Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56 ` [PATCH v3 13/15] phy: rockchip-emmc: Minor code cleanup in rockchip_emmc_phy_power_on/off() Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56 ` [PATCH v3 14/15] phy: rockchip-emmc: Set phyctrl_frqsel based on card clock Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 18:14   ` Heiko Stübner
2016-06-20 18:14     ` Heiko Stübner
2016-06-20 17:56 ` [PATCH v3 15/15] arm64: dts: rockchip: Provide emmcclk to PHY for rk3399 Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-20 17:56   ` Douglas Anderson
2016-06-22 16:31   ` Heiko Stübner
2016-06-22 16:31     ` Heiko Stübner
2016-06-22 16:31     ` Heiko Stübner
2016-06-20 18:17 ` [PATCH v3 0/15] Changes to support 150 MHz eMMC on rk3399 Heiko Stübner
2016-06-20 18:17   ` Heiko Stübner
2016-06-22 15:23 ` Ulf Hansson
2016-06-22 15:23   ` Ulf Hansson
2016-06-22 15:23   ` Ulf Hansson

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1466445414-11974-9-git-send-email-dianders@chromium.org \
    --to=dianders@chromium.org \
    --cc=adrian.hunter@intel.com \
    --cc=briannorris@chromium.org \
    --cc=devicetree@vger.kernel.org \
    --cc=groeck@chromium.org \
    --cc=heiko@sntech.de \
    --cc=kishon@ti.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-mmc@vger.kernel.org \
    --cc=linux-rockchip@lists.infradead.org \
    --cc=michal.simek@xilinx.com \
    --cc=robh+dt@kernel.org \
    --cc=shawn.lin@rock-chips.com \
    --cc=soren.brinkmann@xilinx.com \
    --cc=ulf.hansson@linaro.org \
    --cc=xzy.xu@rock-chips.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.