From: <min.guo@mediatek.com>
To: Bin Liu <b-liu@ti.com>, Rob Herring <robh+dt@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Mark Rutland <mark.rutland@arm.com>,
Matthias Brugger <matthias.bgg@gmail.com>,
Alan Stern <stern@rowland.harvard.edu>,
<chunfeng.yun@mediatek.com>, <linux-usb@vger.kernel.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-mediatek@lists.infradead.org>,
Min Guo <min.guo@mediatek.com>
Subject: [PATCH 1/4] dt-bindings: usb: musb: Add support for MediaTek musb controller
Date: Thu, 27 Dec 2018 15:34:23 +0800 [thread overview]
Message-ID: <1545896066-897-2-git-send-email-min.guo@mediatek.com> (raw)
In-Reply-To: <1545896066-897-1-git-send-email-min.guo@mediatek.com>
From: Min Guo <min.guo@mediatek.com>
This adds support for MediaTek musb controller in
host, peripheral and otg mode
Signed-off-by: Min Guo <min.guo@mediatek.com>
---
.../devicetree/bindings/usb/mediatek,musb.txt | 49 ++++++++++++++++++++++
1 file changed, 49 insertions(+)
create mode 100644 Documentation/devicetree/bindings/usb/mediatek,musb.txt
diff --git a/Documentation/devicetree/bindings/usb/mediatek,musb.txt b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
new file mode 100644
index 0000000..e899c9b
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
@@ -0,0 +1,49 @@
+MediaTek musb DRC/OTG controller
+-------------------------------------------
+
+Required properties:
+ - compatible : should be "mediatek,<soc-model>-musb",
+ "mediatek,mtk-musb", soc-model is the name of SoC, such as
+ mt2701, when using "mediatek,mtk-musb" compatible string, you
+ need SoC specific ones in addition, one of:
+ - "mediatek,mt2701-musb"
+ - reg : specifies physical base address and size of
+ the registers
+ - interrupts : interrupt used by musb controller
+ - interrupt-names : must be "mc"
+ - phys : PHY specifier for the OTG phy
+ - phy-names : should be "usb2-phy"
+ - dr_mode : should be one of "host", "peripheral" or "otg",
+ refer to usb/generic.txt
+ - clocks : a list of phandle + clock-specifier pairs, one for
+ each entry in clock-names
+ - clock-names : must contain "main","mcu","univpll"
+ for clocks of controller
+
+Optional properties:
+ - extcon : external connector for VBUS and IDPIN changes detection,
+ needed when supports dual-role mode.
+ - vbus-supply : reference to the VBUS regulator, needed when supports
+ dual-role mode.
+ - power-domains : a phandle to USB power domain node to control USB's
+ MTCMOS
+
+Example:
+
+usb2: usb@11200000 {
+ compatible = "mediatek,mt2701-musb";
+ "mediatek,mtk-musb";
+ reg = <0 0x11200000 0 0x1000>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "mc";
+ phys = <&u2port2 PHY_TYPE_USB2>;
+ phy-names = "usb2-phy";
+ vbus-supply = <&usb_vbus>;
+ extcon = <&extcon_usb>;
+ dr_mode = "otg";
+ clocks = <&pericfg CLK_PERI_USB0>,
+ <&pericfg CLK_PERI_USB0_MCU>,
+ <&pericfg CLK_PERI_USB_SLV>;
+ clock-names = "main","mcu","univpll";
+ power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>;
+};
--
1.9.1
WARNING: multiple messages have this Message-ID (diff)
From: <min.guo@mediatek.com>
To: Bin Liu <b-liu@ti.com>, Rob Herring <robh+dt@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Mark Rutland <mark.rutland@arm.com>,
Matthias Brugger <matthias.bgg@gmail.com>,
Alan Stern <stern@rowland.harvard.edu>,
chunfeng.yun@mediatek.com, linux-usb@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-mediatek@lists.infradead.org,
Min Guo <min.guo@mediatek.com>
Subject: [PATCH 1/4] dt-bindings: usb: musb: Add support for MediaTek musb controller
Date: Thu, 27 Dec 2018 15:34:23 +0800 [thread overview]
Message-ID: <1545896066-897-2-git-send-email-min.guo@mediatek.com> (raw)
In-Reply-To: <1545896066-897-1-git-send-email-min.guo@mediatek.com>
From: Min Guo <min.guo@mediatek.com>
This adds support for MediaTek musb controller in
host, peripheral and otg mode
Signed-off-by: Min Guo <min.guo@mediatek.com>
---
.../devicetree/bindings/usb/mediatek,musb.txt | 49 ++++++++++++++++++++++
1 file changed, 49 insertions(+)
create mode 100644 Documentation/devicetree/bindings/usb/mediatek,musb.txt
diff --git a/Documentation/devicetree/bindings/usb/mediatek,musb.txt b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
new file mode 100644
index 0000000..e899c9b
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
@@ -0,0 +1,49 @@
+MediaTek musb DRC/OTG controller
+-------------------------------------------
+
+Required properties:
+ - compatible : should be "mediatek,<soc-model>-musb",
+ "mediatek,mtk-musb", soc-model is the name of SoC, such as
+ mt2701, when using "mediatek,mtk-musb" compatible string, you
+ need SoC specific ones in addition, one of:
+ - "mediatek,mt2701-musb"
+ - reg : specifies physical base address and size of
+ the registers
+ - interrupts : interrupt used by musb controller
+ - interrupt-names : must be "mc"
+ - phys : PHY specifier for the OTG phy
+ - phy-names : should be "usb2-phy"
+ - dr_mode : should be one of "host", "peripheral" or "otg",
+ refer to usb/generic.txt
+ - clocks : a list of phandle + clock-specifier pairs, one for
+ each entry in clock-names
+ - clock-names : must contain "main","mcu","univpll"
+ for clocks of controller
+
+Optional properties:
+ - extcon : external connector for VBUS and IDPIN changes detection,
+ needed when supports dual-role mode.
+ - vbus-supply : reference to the VBUS regulator, needed when supports
+ dual-role mode.
+ - power-domains : a phandle to USB power domain node to control USB's
+ MTCMOS
+
+Example:
+
+usb2: usb@11200000 {
+ compatible = "mediatek,mt2701-musb";
+ "mediatek,mtk-musb";
+ reg = <0 0x11200000 0 0x1000>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "mc";
+ phys = <&u2port2 PHY_TYPE_USB2>;
+ phy-names = "usb2-phy";
+ vbus-supply = <&usb_vbus>;
+ extcon = <&extcon_usb>;
+ dr_mode = "otg";
+ clocks = <&pericfg CLK_PERI_USB0>,
+ <&pericfg CLK_PERI_USB0_MCU>,
+ <&pericfg CLK_PERI_USB_SLV>;
+ clock-names = "main","mcu","univpll";
+ power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>;
+};
--
1.9.1
WARNING: multiple messages have this Message-ID (diff)
From: min.guo@mediatek.com
To: Bin Liu <b-liu@ti.com>, Rob Herring <robh+dt@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Mark Rutland <mark.rutland@arm.com>,
Matthias Brugger <matthias.bgg@gmail.com>,
Alan Stern <stern@rowland.harvard.edu>,
chunfeng.yun@mediatek.com, linux-usb@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-mediatek@lists.infradead.org,
Min Guo <min.guo@mediatek.com>
Subject: [1/4] dt-bindings: usb: musb: Add support for MediaTek musb controller
Date: Thu, 27 Dec 2018 15:34:23 +0800 [thread overview]
Message-ID: <1545896066-897-2-git-send-email-min.guo@mediatek.com> (raw)
From: Min Guo <min.guo@mediatek.com>
This adds support for MediaTek musb controller in
host, peripheral and otg mode
Signed-off-by: Min Guo <min.guo@mediatek.com>
---
.../devicetree/bindings/usb/mediatek,musb.txt | 49 ++++++++++++++++++++++
1 file changed, 49 insertions(+)
create mode 100644 Documentation/devicetree/bindings/usb/mediatek,musb.txt
diff --git a/Documentation/devicetree/bindings/usb/mediatek,musb.txt b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
new file mode 100644
index 0000000..e899c9b
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
@@ -0,0 +1,49 @@
+MediaTek musb DRC/OTG controller
+-------------------------------------------
+
+Required properties:
+ - compatible : should be "mediatek,<soc-model>-musb",
+ "mediatek,mtk-musb", soc-model is the name of SoC, such as
+ mt2701, when using "mediatek,mtk-musb" compatible string, you
+ need SoC specific ones in addition, one of:
+ - "mediatek,mt2701-musb"
+ - reg : specifies physical base address and size of
+ the registers
+ - interrupts : interrupt used by musb controller
+ - interrupt-names : must be "mc"
+ - phys : PHY specifier for the OTG phy
+ - phy-names : should be "usb2-phy"
+ - dr_mode : should be one of "host", "peripheral" or "otg",
+ refer to usb/generic.txt
+ - clocks : a list of phandle + clock-specifier pairs, one for
+ each entry in clock-names
+ - clock-names : must contain "main","mcu","univpll"
+ for clocks of controller
+
+Optional properties:
+ - extcon : external connector for VBUS and IDPIN changes detection,
+ needed when supports dual-role mode.
+ - vbus-supply : reference to the VBUS regulator, needed when supports
+ dual-role mode.
+ - power-domains : a phandle to USB power domain node to control USB's
+ MTCMOS
+
+Example:
+
+usb2: usb@11200000 {
+ compatible = "mediatek,mt2701-musb";
+ "mediatek,mtk-musb";
+ reg = <0 0x11200000 0 0x1000>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "mc";
+ phys = <&u2port2 PHY_TYPE_USB2>;
+ phy-names = "usb2-phy";
+ vbus-supply = <&usb_vbus>;
+ extcon = <&extcon_usb>;
+ dr_mode = "otg";
+ clocks = <&pericfg CLK_PERI_USB0>,
+ <&pericfg CLK_PERI_USB0_MCU>,
+ <&pericfg CLK_PERI_USB_SLV>;
+ clock-names = "main","mcu","univpll";
+ power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>;
+};
WARNING: multiple messages have this Message-ID (diff)
From: <min.guo@mediatek.com>
To: Bin Liu <b-liu@ti.com>, Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>,
devicetree@vger.kernel.org,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
linux-usb@vger.kernel.org, linux-kernel@vger.kernel.org,
Matthias Brugger <matthias.bgg@gmail.com>,
Alan Stern <stern@rowland.harvard.edu>,
Min Guo <min.guo@mediatek.com>,
chunfeng.yun@mediatek.com, linux-mediatek@lists.infradead.org,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH 1/4] dt-bindings: usb: musb: Add support for MediaTek musb controller
Date: Thu, 27 Dec 2018 15:34:23 +0800 [thread overview]
Message-ID: <1545896066-897-2-git-send-email-min.guo@mediatek.com> (raw)
In-Reply-To: <1545896066-897-1-git-send-email-min.guo@mediatek.com>
From: Min Guo <min.guo@mediatek.com>
This adds support for MediaTek musb controller in
host, peripheral and otg mode
Signed-off-by: Min Guo <min.guo@mediatek.com>
---
.../devicetree/bindings/usb/mediatek,musb.txt | 49 ++++++++++++++++++++++
1 file changed, 49 insertions(+)
create mode 100644 Documentation/devicetree/bindings/usb/mediatek,musb.txt
diff --git a/Documentation/devicetree/bindings/usb/mediatek,musb.txt b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
new file mode 100644
index 0000000..e899c9b
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
@@ -0,0 +1,49 @@
+MediaTek musb DRC/OTG controller
+-------------------------------------------
+
+Required properties:
+ - compatible : should be "mediatek,<soc-model>-musb",
+ "mediatek,mtk-musb", soc-model is the name of SoC, such as
+ mt2701, when using "mediatek,mtk-musb" compatible string, you
+ need SoC specific ones in addition, one of:
+ - "mediatek,mt2701-musb"
+ - reg : specifies physical base address and size of
+ the registers
+ - interrupts : interrupt used by musb controller
+ - interrupt-names : must be "mc"
+ - phys : PHY specifier for the OTG phy
+ - phy-names : should be "usb2-phy"
+ - dr_mode : should be one of "host", "peripheral" or "otg",
+ refer to usb/generic.txt
+ - clocks : a list of phandle + clock-specifier pairs, one for
+ each entry in clock-names
+ - clock-names : must contain "main","mcu","univpll"
+ for clocks of controller
+
+Optional properties:
+ - extcon : external connector for VBUS and IDPIN changes detection,
+ needed when supports dual-role mode.
+ - vbus-supply : reference to the VBUS regulator, needed when supports
+ dual-role mode.
+ - power-domains : a phandle to USB power domain node to control USB's
+ MTCMOS
+
+Example:
+
+usb2: usb@11200000 {
+ compatible = "mediatek,mt2701-musb";
+ "mediatek,mtk-musb";
+ reg = <0 0x11200000 0 0x1000>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "mc";
+ phys = <&u2port2 PHY_TYPE_USB2>;
+ phy-names = "usb2-phy";
+ vbus-supply = <&usb_vbus>;
+ extcon = <&extcon_usb>;
+ dr_mode = "otg";
+ clocks = <&pericfg CLK_PERI_USB0>,
+ <&pericfg CLK_PERI_USB0_MCU>,
+ <&pericfg CLK_PERI_USB_SLV>;
+ clock-names = "main","mcu","univpll";
+ power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>;
+};
--
1.9.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2018-12-27 7:35 UTC|newest]
Thread overview: 71+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-12-27 7:34 [PATCH 0/4] Add MediaTek MUSB Controller Driver min.guo
2018-12-27 7:34 ` min.guo
2018-12-27 7:34 ` min.guo
2018-12-27 7:34 ` min.guo [this message]
2018-12-27 7:34 ` [PATCH 1/4] dt-bindings: usb: musb: Add support for MediaTek musb controller min.guo
2018-12-27 7:34 ` [1/4] " min.guo
2018-12-27 7:34 ` [PATCH 1/4] " min.guo
2019-01-03 22:14 ` Rob Herring
2019-01-03 22:14 ` Rob Herring
2019-01-03 22:14 ` [1/4] " Rob Herring
2019-01-04 3:00 ` [PATCH 1/4] " Min Guo
2019-01-04 3:00 ` Min Guo
2019-01-04 3:00 ` [1/4] " min.guo
2019-01-04 3:00 ` [PATCH 1/4] " Min Guo
2019-01-04 16:10 ` Rob Herring
2019-01-04 16:10 ` Rob Herring
2019-01-04 16:10 ` [1/4] " Rob Herring
2019-01-04 16:10 ` [PATCH 1/4] " Rob Herring
2019-01-07 7:31 ` Min Guo
2019-01-07 7:31 ` Min Guo
2019-01-07 7:31 ` [1/4] " min.guo
2019-01-07 7:31 ` [PATCH 1/4] " Min Guo
2019-01-08 14:05 ` Rob Herring
2019-01-07 20:40 ` Bin Liu
2019-01-07 20:40 ` Bin Liu
2019-01-07 20:40 ` [1/4] " Bin Liu
2019-01-07 20:40 ` [PATCH 1/4] " Bin Liu
2019-01-08 1:30 ` Min Guo
2019-01-08 1:30 ` Min Guo
2019-01-08 1:30 ` [1/4] " min.guo
2019-01-08 1:30 ` [PATCH 1/4] " Min Guo
2018-12-27 7:34 ` [PATCH 2/4] arm: dts: mt2701: Add usb2 device nodes min.guo
2018-12-27 7:34 ` min.guo
2018-12-27 7:34 ` [2/4] " min.guo
2018-12-27 7:34 ` [PATCH 2/4] " min.guo
2018-12-27 7:34 ` [PATCH 3/4] usb: musb: Move musbhsdma macro definition to musb_dma.h min.guo
2018-12-27 7:34 ` min.guo
2018-12-27 7:34 ` [3/4] " min.guo
2018-12-27 7:34 ` [PATCH 3/4] " min.guo
2018-12-27 7:34 ` [PATCH 4/4] usb: musb: Add support for MediaTek musb controller min.guo
2018-12-27 7:34 ` min.guo
2018-12-27 7:34 ` [4/4] " min.guo
2018-12-27 7:34 ` [PATCH 4/4] " min.guo
2019-01-08 15:44 ` Bin Liu
2019-01-08 15:44 ` Bin Liu
2019-01-08 15:44 ` [4/4] " Bin Liu
2019-01-08 15:44 ` [PATCH 4/4] " Bin Liu
2019-01-09 12:31 ` Min Guo
2019-01-09 12:31 ` Min Guo
2019-01-09 12:31 ` [4/4] " min.guo
2019-01-09 12:31 ` [PATCH 4/4] " Min Guo
2019-01-09 14:01 ` Bin Liu
2019-01-09 14:01 ` Bin Liu
2019-01-09 14:01 ` [4/4] " Bin Liu
2019-01-09 14:01 ` [PATCH 4/4] " Bin Liu
2019-01-10 7:24 ` Min Guo
2019-01-10 7:24 ` Min Guo
2019-01-10 7:24 ` [4/4] " min.guo
2019-01-10 7:24 ` [PATCH 4/4] " Min Guo
2019-01-10 14:18 ` Bin Liu
2019-01-10 14:18 ` Bin Liu
2019-01-10 14:18 ` [4/4] " Bin Liu
2019-01-10 14:18 ` [PATCH 4/4] " Bin Liu
2019-01-11 1:18 ` Min Guo
2019-01-11 1:18 ` Min Guo
2019-01-11 1:18 ` [4/4] " min.guo
2019-01-11 1:18 ` [PATCH 4/4] " Min Guo
2019-01-11 5:24 ` Min Guo
2019-01-11 5:24 ` Min Guo
2019-01-11 5:24 ` [4/4] " min.guo
2019-01-11 5:24 ` [PATCH 4/4] " Min Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1545896066-897-2-git-send-email-min.guo@mediatek.com \
--to=min.guo@mediatek.com \
--cc=b-liu@ti.com \
--cc=chunfeng.yun@mediatek.com \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=linux-usb@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=matthias.bgg@gmail.com \
--cc=robh+dt@kernel.org \
--cc=stern@rowland.harvard.edu \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.