From: Sascha Hauer <s.hauer@pengutronix.de> To: Punit Agrawal <punit.agrawal@arm.com> Cc: linux-pm@vger.kernel.org, Zhang Rui <rui.zhang@intel.com>, Eduardo Valentin <edubezval@gmail.com>, linux-kernel@vger.kernel.org, kernel@pengutronix.de, linux-mediatek@lists.infradead.org, linux-arm-kernel@lists.infradead.org, Matthias Brugger <matthias.bgg@gmail.com>, devicetree@vger.kernel.org, mark.rutland@arm.com, robh+dt@kernel.org Subject: Re: [PATCH 2/3] thermal: Add Mediatek thermal controller support Date: Wed, 30 Sep 2015 12:37:04 +0200 [thread overview] Message-ID: <20150930103704.GA7858@pengutronix.de> (raw) In-Reply-To: <9hhpp105jw1.fsf@e105922-lin.cambridge.arm.com> Hi Punit, On Wed, Sep 30, 2015 at 10:36:14AM +0100, Punit Agrawal wrote: > Hi Sascha, > > Re-posting a comment from v7. Perhaps you missed it... Uh, sorry. In fact I didn't miss it and I thought I have answered it. Appearantly I haven't. > > + struct mtk_thermal *mt = bank->mt; > > + int temp, i, max; > > + u32 raw; > > + > > + temp = max = INT_MIN; > > + > > + for (i = 0; i < bank_data[bank->id].num_sensors; i++) { > > + raw = readl(mt->thermal_base + sensing_points[i].msr); > > + > > + temp = raw_to_mcelsius(mt, raw); > > + > > + /* > > + * The first read of a sensor often contains very high bogus > > + * temperature value. Filter these out so that the system does > > + * not immediately shut down. > > + */ > > + if (temp > 200000) > > + temp = 0; > > + > > If the bogus value is only the first time the sensor is read, instead of > filtering here, you could call mtk_thermal_bank_temperature at probe > time when you are initialising the banks and ignore the returned value. It seems that after initialization the hardware needs some time to settle before correct values can be read. Doing what you suggest would mean we have to delay the boot by several 100ms. I'd rather not do that. Sascha -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
WARNING: multiple messages have this Message-ID (diff)
From: s.hauer@pengutronix.de (Sascha Hauer) To: linux-arm-kernel@lists.infradead.org Subject: [PATCH 2/3] thermal: Add Mediatek thermal controller support Date: Wed, 30 Sep 2015 12:37:04 +0200 [thread overview] Message-ID: <20150930103704.GA7858@pengutronix.de> (raw) In-Reply-To: <9hhpp105jw1.fsf@e105922-lin.cambridge.arm.com> Hi Punit, On Wed, Sep 30, 2015 at 10:36:14AM +0100, Punit Agrawal wrote: > Hi Sascha, > > Re-posting a comment from v7. Perhaps you missed it... Uh, sorry. In fact I didn't miss it and I thought I have answered it. Appearantly I haven't. > > + struct mtk_thermal *mt = bank->mt; > > + int temp, i, max; > > + u32 raw; > > + > > + temp = max = INT_MIN; > > + > > + for (i = 0; i < bank_data[bank->id].num_sensors; i++) { > > + raw = readl(mt->thermal_base + sensing_points[i].msr); > > + > > + temp = raw_to_mcelsius(mt, raw); > > + > > + /* > > + * The first read of a sensor often contains very high bogus > > + * temperature value. Filter these out so that the system does > > + * not immediately shut down. > > + */ > > + if (temp > 200000) > > + temp = 0; > > + > > If the bogus value is only the first time the sensor is read, instead of > filtering here, you could call mtk_thermal_bank_temperature at probe > time when you are initialising the banks and ignore the returned value. It seems that after initialization the hardware needs some time to settle before correct values can be read. Doing what you suggest would mean we have to delay the boot by several 100ms. I'd rather not do that. Sascha -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
next prev parent reply other threads:[~2015-09-30 10:37 UTC|newest] Thread overview: 135+ messages / expand[flat|nested] mbox.gz Atom feed top 2015-09-23 13:37 [PATCH v9] Add Mediatek thermal support Sascha Hauer 2015-09-23 13:37 ` Sascha Hauer 2015-09-23 13:37 ` [PATCH 1/3] dt-bindings: thermal: Add binding document for Mediatek thermal controller Sascha Hauer 2015-09-23 13:37 ` Sascha Hauer 2015-09-23 13:37 ` [PATCH 2/3] thermal: Add Mediatek thermal controller support Sascha Hauer 2015-09-23 13:37 ` Sascha Hauer 2015-09-23 18:31 ` Vladimir Zapolskiy 2015-09-23 18:31 ` Vladimir Zapolskiy 2015-09-23 18:31 ` Vladimir Zapolskiy 2015-09-30 6:14 ` Sascha Hauer 2015-09-30 6:14 ` Sascha Hauer 2015-09-29 23:04 ` Eduardo Valentin 2015-09-29 23:04 ` Eduardo Valentin 2015-09-29 23:04 ` Eduardo Valentin 2015-09-30 6:13 ` Sascha Hauer 2015-09-30 6:13 ` Sascha Hauer 2015-09-30 9:36 ` Punit Agrawal 2015-09-30 9:36 ` Punit Agrawal 2015-09-30 9:36 ` Punit Agrawal 2015-09-30 10:37 ` Sascha Hauer [this message] 2015-09-30 10:37 ` Sascha Hauer 2015-09-30 11:07 ` Punit Agrawal 2015-09-30 11:07 ` Punit Agrawal 2015-09-23 13:37 ` [PATCH 3/3] ARM64: dts: mt8173: Add thermal/auxadc device nodes Sascha Hauer 2015-09-23 13:37 ` Sascha Hauer -- strict thread matches above, loose matches on Subject: below -- 2015-11-30 11:42 [PATCH v12] Add Mediatek thermal support Sascha Hauer 2015-11-30 11:42 ` [PATCH 2/3] thermal: Add Mediatek thermal controller support Sascha Hauer 2015-11-30 11:42 ` Sascha Hauer 2015-12-17 19:33 ` Eduardo Valentin 2015-12-17 19:33 ` Eduardo Valentin 2016-01-04 14:19 ` Sascha Hauer 2016-01-04 14:19 ` Sascha Hauer 2016-01-19 7:29 ` Sascha Hauer 2016-01-19 7:29 ` Sascha Hauer 2016-02-01 2:54 ` Eddie Huang 2016-02-01 2:54 ` Eddie Huang 2016-02-01 2:54 ` Eddie Huang 2016-02-15 2:11 ` Daniel Kurtz 2016-02-15 2:11 ` Daniel Kurtz 2016-02-15 2:11 ` Daniel Kurtz 2016-02-15 2:14 ` Daniel Kurtz 2016-02-15 2:14 ` Daniel Kurtz 2016-02-15 2:14 ` Daniel Kurtz 2016-02-17 17:05 ` Matthias Brugger 2016-02-17 17:05 ` Matthias Brugger 2016-02-17 17:05 ` Matthias Brugger 2016-02-18 10:56 ` Sascha Hauer 2016-02-18 10:56 ` Sascha Hauer 2016-02-18 10:56 ` Sascha Hauer 2016-02-18 14:28 ` Javi Merino 2016-02-18 14:28 ` Javi Merino 2016-02-18 14:28 ` Javi Merino 2016-02-18 15:15 ` Eduardo Valentin 2016-02-18 15:15 ` Eduardo Valentin 2016-02-18 15:15 ` Eduardo Valentin 2016-02-19 7:21 ` Sascha Hauer 2016-02-19 7:21 ` Sascha Hauer 2016-02-19 7:21 ` Sascha Hauer 2015-12-21 4:07 ` Daniel Kurtz 2015-12-21 4:07 ` Daniel Kurtz 2015-12-21 4:07 ` Daniel Kurtz 2016-01-04 14:31 ` Sascha Hauer 2016-01-04 14:31 ` Sascha Hauer 2016-01-04 14:31 ` Sascha Hauer 2016-01-04 15:43 ` Daniel Kurtz 2016-01-04 15:43 ` Daniel Kurtz 2016-01-04 15:43 ` Daniel Kurtz 2015-11-18 8:24 [PATCH v11] Add Mediatek thermal support Sascha Hauer 2015-11-18 8:24 ` [PATCH 2/3] thermal: Add Mediatek thermal controller support Sascha Hauer 2015-11-18 8:24 ` Sascha Hauer 2015-11-24 6:06 ` dawei chien 2015-11-24 6:06 ` dawei chien 2015-11-24 6:06 ` dawei chien 2015-11-24 7:53 ` Sascha Hauer 2015-11-24 7:53 ` Sascha Hauer 2015-11-09 10:13 [PATCH v10] Add Mediatek thermal support Sascha Hauer 2015-11-09 10:13 ` [PATCH 2/3] thermal: Add Mediatek thermal controller support Sascha Hauer 2015-11-09 10:13 ` Sascha Hauer 2015-11-09 10:13 ` Sascha Hauer 2015-11-09 14:39 ` Andy Shevchenko 2015-11-09 14:39 ` Andy Shevchenko 2015-11-18 8:11 ` Sascha Hauer 2015-11-18 8:11 ` Sascha Hauer 2015-11-18 8:11 ` Sascha Hauer 2015-11-10 12:05 ` Javi Merino 2015-11-10 12:05 ` Javi Merino 2015-11-10 18:26 ` Eduardo Valentin 2015-11-10 18:26 ` Eduardo Valentin 2015-11-11 7:27 ` Sascha Hauer 2015-11-11 7:27 ` Sascha Hauer 2015-11-11 9:40 ` Javi Merino 2015-11-11 9:40 ` Javi Merino 2015-11-11 9:40 ` Javi Merino 2015-11-13 10:09 ` Sascha Hauer 2015-11-13 10:09 ` Sascha Hauer 2015-11-13 11:26 ` Javi Merino 2015-11-13 11:26 ` Javi Merino 2015-11-18 8:18 ` Sascha Hauer 2015-11-18 8:18 ` Sascha Hauer 2015-08-31 7:34 [PATCH v8] Add Mediatek thermal support Sascha Hauer 2015-08-31 7:34 ` [PATCH 2/3] thermal: Add Mediatek thermal controller support Sascha Hauer 2015-08-31 7:34 ` Sascha Hauer 2015-08-31 7:34 ` Sascha Hauer 2015-09-14 7:32 ` Daniel Kurtz 2015-09-14 7:32 ` Daniel Kurtz 2015-09-14 7:32 ` Daniel Kurtz 2015-09-22 7:30 ` Daniel Kurtz 2015-09-22 7:30 ` Daniel Kurtz 2015-09-22 7:30 ` Daniel Kurtz 2015-09-22 8:30 ` Sascha Hauer 2015-09-22 8:30 ` Sascha Hauer 2015-09-22 8:30 ` Sascha Hauer 2015-08-27 6:41 [PATCH v7] Add Mediatek thermal support Sascha Hauer 2015-08-27 6:41 ` [PATCH 2/3] thermal: Add Mediatek thermal controller support Sascha Hauer 2015-08-27 11:50 ` Punit Agrawal 2015-08-26 13:58 [PATCH v6] Add Mediatek thermal support Sascha Hauer 2015-08-26 13:58 ` [PATCH 2/3] thermal: Add Mediatek thermal controller support Sascha Hauer 2015-08-20 8:05 [PATCH v5] Add Mediatek thermal support Sascha Hauer 2015-08-20 8:06 ` [PATCH 2/3] thermal: Add Mediatek thermal controller support Sascha Hauer 2015-08-20 22:20 ` Eduardo Valentin 2015-08-20 22:29 ` Daniel Lezcano 2015-08-21 5:06 ` Sascha Hauer 2015-08-20 23:12 ` Daniel Lezcano 2015-08-26 13:54 ` Sascha Hauer 2015-08-26 14:02 ` Daniel Lezcano 2015-08-25 17:41 ` Daniel Kurtz 2015-08-07 13:55 [PATCH v4] Add Mediatek thermal support Sascha Hauer 2015-08-07 13:55 ` [PATCH 2/3] thermal: Add Mediatek thermal controller support Sascha Hauer 2015-08-11 7:03 ` Daniel Kurtz 2015-08-20 7:57 ` Sascha Hauer 2015-08-05 12:25 [PATCH v3] Add Mediatek thermal support Sascha Hauer 2015-08-05 12:25 ` [PATCH 2/3] thermal: Add Mediatek thermal controller support Sascha Hauer 2015-08-05 18:02 ` Daniel Kurtz 2015-08-06 8:10 ` Sascha Hauer 2015-07-21 7:59 [PATCH v2] Add Mediatek thermal support Sascha Hauer 2015-07-21 7:59 ` [PATCH 2/3] thermal: Add Mediatek thermal controller support Sascha Hauer 2015-07-21 7:59 ` Sascha Hauer 2015-07-21 15:13 ` Daniel Kurtz 2015-07-21 15:13 ` Daniel Kurtz 2015-07-21 15:13 ` Daniel Kurtz 2015-08-05 10:20 ` Sascha Hauer 2015-08-05 10:20 ` Sascha Hauer 2015-08-05 10:20 ` Sascha Hauer 2015-07-13 10:34 [PATCH] thermal: Add Mediatek thermal support Sascha Hauer 2015-07-13 10:34 ` [PATCH 2/3] thermal: Add Mediatek thermal controller support Sascha Hauer 2015-07-13 10:34 ` Sascha Hauer
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20150930103704.GA7858@pengutronix.de \ --to=s.hauer@pengutronix.de \ --cc=devicetree@vger.kernel.org \ --cc=edubezval@gmail.com \ --cc=kernel@pengutronix.de \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-mediatek@lists.infradead.org \ --cc=linux-pm@vger.kernel.org \ --cc=mark.rutland@arm.com \ --cc=matthias.bgg@gmail.com \ --cc=punit.agrawal@arm.com \ --cc=robh+dt@kernel.org \ --cc=rui.zhang@intel.com \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.