From: Guillaume La Roque <glaroque@baylibre.com> To: linus.walleij@linaro.org, khilman@baylibre.com Cc: jbrunet@baylibre.com, linux-gpio@vger.kernel.org, devicetree@vger.kernel.org, linux-amlogic@lists.infradead.org, linux-kernel@vger.kernel.org Subject: [PATCH v4 1/6] dt-bindings: pinctrl: add a 'drive-strength-microamp' property Date: Thu, 9 May 2019 18:29:15 +0200 [thread overview] Message-ID: <20190509162920.7054-2-glaroque@baylibre.com> (raw) In-Reply-To: <20190509162920.7054-1-glaroque@baylibre.com> This property allow drive-strength parameter in uA instead of mA. Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> --- Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt | 3 +++ 1 file changed, 3 insertions(+) diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt index cef2b5855d60..84adce9f2a75 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt @@ -258,6 +258,7 @@ drive-push-pull - drive actively high and low drive-open-drain - drive with open drain drive-open-source - drive with open source drive-strength - sink or source at most X mA +drive-strength-microamp - sink or source at most X uA input-enable - enable input on pin (no effect on output, such as enabling an input buffer) input-disable - disable input on pin (no effect on output, such as @@ -326,6 +327,8 @@ arguments are described below. - drive-strength takes as argument the target strength in mA. +- drive-strength-uA takes as argument the target strength in uA. + - input-debounce takes the debounce time in usec as argument or 0 to disable debouncing -- 2.17.1
WARNING: multiple messages have this Message-ID (diff)
From: Guillaume La Roque <glaroque@baylibre.com> To: linus.walleij@linaro.org, khilman@baylibre.com Cc: linux-gpio@vger.kernel.org, devicetree@vger.kernel.org, linux-amlogic@lists.infradead.org, linux-kernel@vger.kernel.org, jbrunet@baylibre.com Subject: [PATCH v4 1/6] dt-bindings: pinctrl: add a 'drive-strength-microamp' property Date: Thu, 9 May 2019 18:29:15 +0200 [thread overview] Message-ID: <20190509162920.7054-2-glaroque@baylibre.com> (raw) In-Reply-To: <20190509162920.7054-1-glaroque@baylibre.com> This property allow drive-strength parameter in uA instead of mA. Signed-off-by: Guillaume La Roque <glaroque@baylibre.com> --- Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt | 3 +++ 1 file changed, 3 insertions(+) diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt index cef2b5855d60..84adce9f2a75 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt @@ -258,6 +258,7 @@ drive-push-pull - drive actively high and low drive-open-drain - drive with open drain drive-open-source - drive with open source drive-strength - sink or source at most X mA +drive-strength-microamp - sink or source at most X uA input-enable - enable input on pin (no effect on output, such as enabling an input buffer) input-disable - disable input on pin (no effect on output, such as @@ -326,6 +327,8 @@ arguments are described below. - drive-strength takes as argument the target strength in mA. +- drive-strength-uA takes as argument the target strength in uA. + - input-debounce takes the debounce time in usec as argument or 0 to disable debouncing -- 2.17.1 _______________________________________________ linux-amlogic mailing list linux-amlogic@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-amlogic
next prev parent reply other threads:[~2019-05-09 16:29 UTC|newest] Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top 2019-05-09 16:29 [PATCH v4 0/6] Add drive-strength in Meson pinctrl driver Guillaume La Roque 2019-05-09 16:29 ` Guillaume La Roque 2019-05-09 16:29 ` Guillaume La Roque [this message] 2019-05-09 16:29 ` [PATCH v4 1/6] dt-bindings: pinctrl: add a 'drive-strength-microamp' property Guillaume La Roque 2019-05-09 17:35 ` Kevin Hilman 2019-05-09 17:35 ` Kevin Hilman 2019-05-09 16:29 ` [PATCH v4 2/6] pinctrl: generic: add new 'drive-strength-microamp' property support Guillaume La Roque 2019-05-09 16:29 ` Guillaume La Roque 2019-05-09 16:29 ` [PATCH v4 3/6] dt-bindings: pinctrl: meson: Add drive-strength-microamp property Guillaume La Roque 2019-05-09 16:29 ` Guillaume La Roque 2019-05-09 16:29 ` [PATCH v4 4/6] pinctrl: meson: Rework enable/disable bias part Guillaume La Roque 2019-05-09 16:29 ` Guillaume La Roque 2019-05-09 16:29 ` [PATCH v4 5/6] pinctrl: meson: add support of drive-strength-microamp Guillaume La Roque 2019-05-09 16:29 ` Guillaume La Roque 2019-05-09 16:29 ` [PATCH v4 6/6] pinctrl: meson: g12a: add DS bank value Guillaume La Roque 2019-05-09 16:29 ` Guillaume La Roque 2019-05-09 17:34 ` [PATCH v4 0/6] Add drive-strength in Meson pinctrl driver Kevin Hilman 2019-05-09 17:34 ` Kevin Hilman -- strict thread matches above, loose matches on Subject: below -- 2019-05-09 16:28 Guillaume La Roque 2019-05-09 16:28 ` [PATCH v4 1/6] dt-bindings: pinctrl: add a 'drive-strength-microamp' property Guillaume La Roque 2019-05-09 16:28 ` Guillaume La Roque
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20190509162920.7054-2-glaroque@baylibre.com \ --to=glaroque@baylibre.com \ --cc=devicetree@vger.kernel.org \ --cc=jbrunet@baylibre.com \ --cc=khilman@baylibre.com \ --cc=linus.walleij@linaro.org \ --cc=linux-amlogic@lists.infradead.org \ --cc=linux-gpio@vger.kernel.org \ --cc=linux-kernel@vger.kernel.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.