From: Andre Przywara <andre.przywara@arm.com> To: Maxime Ripard <mripard@kernel.org>, Chen-Yu Tsai <wens@csie.org>, Jernej Skrabec <jernej.skrabec@gmail.com> Cc: Rob Herring <robh@kernel.org>, Icenowy Zheng <icenowy@aosc.io>, Samuel Holland <samuel@sholland.org>, linux-arm-kernel@lists.infradead.org, linux-sunxi@googlegroups.com, linux-sunxi@lists.linux.dev, linux-kernel@vger.kernel.org, Ondrej Jirman <megous@megous.com>, devicetree@vger.kernel.org Subject: [PATCH v7 19/19] arm64: dts: allwinner: h616: Add X96 Mate TV box support Date: Tue, 15 Jun 2021 12:06:36 +0100 [thread overview] Message-ID: <20210615110636.23403-20-andre.przywara@arm.com> (raw) In-Reply-To: <20210615110636.23403-1-andre.przywara@arm.com> The X96 Mate is an Allwinner H616 based TV box, featuring: - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU - 2GiB/4GiB RAM (fully usable!) - 16/32/64GiB eMMC - 100Mbps Ethernet (via embedded AC200 EPHY, not yet supported) - Unsupported Allwinner WiFi chip - 2 x USB 2.0 host ports - HDMI port - IR receiver - 5V/2A DC power supply via barrel plug For more information see: https://linux-sunxi.org/X96_Mate Add a basic devicetree for it, with SD card, eMMC and USB working, as well as serial and the essential peripherals, like the AXP PMIC. This DT is somewhat minimal, and should work on many other similar TV boxes with the Allwinner H616 chip. Signed-off-by: Andre Przywara <andre.przywara@arm.com> --- arch/arm64/boot/dts/allwinner/Makefile | 1 + .../dts/allwinner/sun50i-h616-x96-mate.dts | 201 ++++++++++++++++++ 2 files changed, 202 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile index 9ba4b5d92657..370d24ebaacf 100644 --- a/arch/arm64/boot/dts/allwinner/Makefile +++ b/arch/arm64/boot/dts/allwinner/Makefile @@ -37,3 +37,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts new file mode 100644 index 000000000000..b960bb310289 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts @@ -0,0 +1,201 @@ +// SPDX-License-Identifier: (GPL-2.0+ or MIT) +/* + * Copyright (C) 2021 Arm Ltd. + */ + +/dts-v1/; + +#include "sun50i-h616.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> + +/ { + model = "X96 Mate"; + compatible = "hechuang,x96-mate", "allwinner,sun50i-h616"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + reg_vcc5v: vcc5v { + /* board wide 5V supply directly from the DC input */ + compatible = "regulator-fixed"; + regulator-name = "vcc-5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci2 { + status = "okay"; +}; + +&ir { + status = "okay"; +}; + +&mmc0 { + vmmc-supply = <®_dcdce>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + bus-width = <4>; + status = "okay"; +}; + +&mmc2 { + vmmc-supply = <®_dcdce>; + vqmmc-supply = <®_bldo1>; + bus-width = <8>; + non-removable; + cap-mmc-hw-reset; + mmc-hs200-1_8v; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci2 { + status = "okay"; +}; + +&r_rsb { + status = "okay"; + + axp305: pmic@745 { + compatible = "x-powers,axp305", "x-powers,axp805", + "x-powers,axp806"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x745>; + + x-powers,self-working-mode; + vina-supply = <®_vcc5v>; + vinb-supply = <®_vcc5v>; + vinc-supply = <®_vcc5v>; + vind-supply = <®_vcc5v>; + vine-supply = <®_vcc5v>; + aldoin-supply = <®_vcc5v>; + bldoin-supply = <®_vcc5v>; + cldoin-supply = <®_vcc5v>; + + regulators { + reg_aldo1: aldo1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-sys"; + }; + + /* Enabled by the Android BSP */ + reg_aldo2: aldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc3v3-ext"; + status = "disabled"; + }; + + /* Enabled by the Android BSP */ + reg_aldo3: aldo3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc3v3-ext2"; + status = "disabled"; + }; + + reg_bldo1: bldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc1v8"; + }; + + /* Enabled by the Android BSP */ + reg_bldo2: bldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc1v8-2"; + status = "disabled"; + }; + + bldo3 { + /* unused */ + }; + + bldo4 { + /* unused */ + }; + + cldo1 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vcc2v5"; + }; + + cldo2 { + /* unused */ + }; + + cldo3 { + /* unused */ + }; + + reg_dcdca: dcdca { + regulator-always-on; + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1080000>; + regulator-name = "vdd-cpu"; + }; + + reg_dcdcc: dcdcc { + regulator-always-on; + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1080000>; + regulator-name = "vdd-gpu-sys"; + }; + + reg_dcdcd: dcdcd { + regulator-always-on; + regulator-min-microvolt = <1360000>; + regulator-max-microvolt = <1360000>; + regulator-name = "vdd-dram"; + }; + + reg_dcdce: dcdce { + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-eth-mmc"; + }; + + sw { + /* unused */ + }; + }; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_ph_pins>; + status = "okay"; +}; + +&usbotg { + dr_mode = "host"; /* USB A type receptable */ + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; -- 2.17.5
WARNING: multiple messages have this Message-ID (diff)
From: Andre Przywara <andre.przywara@arm.com> To: Maxime Ripard <mripard@kernel.org>, Chen-Yu Tsai <wens@csie.org>, Jernej Skrabec <jernej.skrabec@gmail.com> Cc: Rob Herring <robh@kernel.org>, Icenowy Zheng <icenowy@aosc.io>, Samuel Holland <samuel@sholland.org>, linux-arm-kernel@lists.infradead.org, linux-sunxi@googlegroups.com, linux-sunxi@lists.linux.dev, linux-kernel@vger.kernel.org, Ondrej Jirman <megous@megous.com>, devicetree@vger.kernel.org Subject: [PATCH v7 19/19] arm64: dts: allwinner: h616: Add X96 Mate TV box support Date: Tue, 15 Jun 2021 12:06:36 +0100 [thread overview] Message-ID: <20210615110636.23403-20-andre.przywara@arm.com> (raw) In-Reply-To: <20210615110636.23403-1-andre.przywara@arm.com> The X96 Mate is an Allwinner H616 based TV box, featuring: - Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU - 2GiB/4GiB RAM (fully usable!) - 16/32/64GiB eMMC - 100Mbps Ethernet (via embedded AC200 EPHY, not yet supported) - Unsupported Allwinner WiFi chip - 2 x USB 2.0 host ports - HDMI port - IR receiver - 5V/2A DC power supply via barrel plug For more information see: https://linux-sunxi.org/X96_Mate Add a basic devicetree for it, with SD card, eMMC and USB working, as well as serial and the essential peripherals, like the AXP PMIC. This DT is somewhat minimal, and should work on many other similar TV boxes with the Allwinner H616 chip. Signed-off-by: Andre Przywara <andre.przywara@arm.com> --- arch/arm64/boot/dts/allwinner/Makefile | 1 + .../dts/allwinner/sun50i-h616-x96-mate.dts | 201 ++++++++++++++++++ 2 files changed, 202 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile index 9ba4b5d92657..370d24ebaacf 100644 --- a/arch/arm64/boot/dts/allwinner/Makefile +++ b/arch/arm64/boot/dts/allwinner/Makefile @@ -37,3 +37,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts new file mode 100644 index 000000000000..b960bb310289 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts @@ -0,0 +1,201 @@ +// SPDX-License-Identifier: (GPL-2.0+ or MIT) +/* + * Copyright (C) 2021 Arm Ltd. + */ + +/dts-v1/; + +#include "sun50i-h616.dtsi" + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> + +/ { + model = "X96 Mate"; + compatible = "hechuang,x96-mate", "allwinner,sun50i-h616"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + reg_vcc5v: vcc5v { + /* board wide 5V supply directly from the DC input */ + compatible = "regulator-fixed"; + regulator-name = "vcc-5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; +}; + +&ehci0 { + status = "okay"; +}; + +&ehci2 { + status = "okay"; +}; + +&ir { + status = "okay"; +}; + +&mmc0 { + vmmc-supply = <®_dcdce>; + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + bus-width = <4>; + status = "okay"; +}; + +&mmc2 { + vmmc-supply = <®_dcdce>; + vqmmc-supply = <®_bldo1>; + bus-width = <8>; + non-removable; + cap-mmc-hw-reset; + mmc-hs200-1_8v; + status = "okay"; +}; + +&ohci0 { + status = "okay"; +}; + +&ohci2 { + status = "okay"; +}; + +&r_rsb { + status = "okay"; + + axp305: pmic@745 { + compatible = "x-powers,axp305", "x-powers,axp805", + "x-powers,axp806"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x745>; + + x-powers,self-working-mode; + vina-supply = <®_vcc5v>; + vinb-supply = <®_vcc5v>; + vinc-supply = <®_vcc5v>; + vind-supply = <®_vcc5v>; + vine-supply = <®_vcc5v>; + aldoin-supply = <®_vcc5v>; + bldoin-supply = <®_vcc5v>; + cldoin-supply = <®_vcc5v>; + + regulators { + reg_aldo1: aldo1 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-sys"; + }; + + /* Enabled by the Android BSP */ + reg_aldo2: aldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc3v3-ext"; + status = "disabled"; + }; + + /* Enabled by the Android BSP */ + reg_aldo3: aldo3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc3v3-ext2"; + status = "disabled"; + }; + + reg_bldo1: bldo1 { + regulator-always-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc1v8"; + }; + + /* Enabled by the Android BSP */ + reg_bldo2: bldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-name = "vcc1v8-2"; + status = "disabled"; + }; + + bldo3 { + /* unused */ + }; + + bldo4 { + /* unused */ + }; + + cldo1 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vcc2v5"; + }; + + cldo2 { + /* unused */ + }; + + cldo3 { + /* unused */ + }; + + reg_dcdca: dcdca { + regulator-always-on; + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1080000>; + regulator-name = "vdd-cpu"; + }; + + reg_dcdcc: dcdcc { + regulator-always-on; + regulator-min-microvolt = <810000>; + regulator-max-microvolt = <1080000>; + regulator-name = "vdd-gpu-sys"; + }; + + reg_dcdcd: dcdcd { + regulator-always-on; + regulator-min-microvolt = <1360000>; + regulator-max-microvolt = <1360000>; + regulator-name = "vdd-dram"; + }; + + reg_dcdce: dcdce { + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-eth-mmc"; + }; + + sw { + /* unused */ + }; + }; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_ph_pins>; + status = "okay"; +}; + +&usbotg { + dr_mode = "host"; /* USB A type receptable */ + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; -- 2.17.5 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2021-06-15 11:07 UTC|newest] Thread overview: 105+ messages / expand[flat|nested] mbox.gz Atom feed top 2021-06-15 11:06 [PATCH v7 00/19] arm64: sunxi: Initial Allwinner H616 SoC support Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-15 11:06 ` [PATCH v7 01/19] dt-bindings: mfd: axp20x: Add AXP305 compatible (plus optional IRQ) Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-15 23:33 ` Rob Herring 2021-06-15 23:33 ` Rob Herring 2021-06-16 14:57 ` Andre Przywara 2021-06-16 14:57 ` Andre Przywara 2021-06-15 11:06 ` [PATCH v7 02/19] mfd: axp20x: Allow AXP 806 chips without interrupt lines Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-15 11:06 ` [PATCH v7 03/19] dt-bindings: rtc: sun6i: Add H616 compatible string Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-15 23:35 ` Rob Herring 2021-06-15 23:35 ` Rob Herring 2021-06-16 14:59 ` Andre Przywara 2021-06-16 14:59 ` Andre Przywara 2021-06-15 11:06 ` [PATCH v7 04/19] rtc: sun6i: Add support for linear day storage Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-17 18:16 ` kernel test robot 2021-06-17 18:16 ` kernel test robot 2021-06-17 18:16 ` kernel test robot 2021-06-17 20:07 ` kernel test robot 2021-06-17 20:07 ` kernel test robot 2021-06-17 20:07 ` kernel test robot 2021-06-18 15:43 ` Andre Przywara 2021-06-18 15:43 ` Andre Przywara 2021-06-18 15:43 ` Andre Przywara 2021-06-15 11:06 ` [PATCH v7 05/19] rtc: sun6i: Add support for broken-down alarm registers Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-17 23:17 ` kernel test robot 2021-06-17 23:17 ` kernel test robot 2021-06-17 23:17 ` kernel test robot 2021-06-15 11:06 ` [PATCH v7 06/19] rtc: sun6i: Add support for RTCs without external LOSCs Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-16 9:14 ` Maxime Ripard 2021-06-16 9:14 ` Maxime Ripard 2021-06-16 10:14 ` Andre Przywara 2021-06-16 10:14 ` Andre Przywara 2021-06-16 13:47 ` Maxime Ripard 2021-06-16 13:47 ` Maxime Ripard 2021-07-22 23:17 ` Andre Przywara 2021-07-22 23:17 ` Andre Przywara 2021-07-26 14:59 ` Maxime Ripard 2021-07-26 14:59 ` Maxime Ripard 2021-07-29 8:04 ` Icenowy Zheng 2021-07-29 8:04 ` Icenowy Zheng 2021-07-29 8:04 ` Icenowy Zheng 2021-07-29 10:32 ` Maxime Ripard 2021-07-29 10:32 ` Maxime Ripard 2021-07-29 13:04 ` Icenowy Zheng 2021-07-29 13:04 ` Icenowy Zheng 2021-06-15 11:06 ` [PATCH v7 07/19] rtc: sun6i: Add Allwinner H616 support Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-15 11:06 ` [PATCH v7 08/19] dt-bindings: net: sun8i-emac: Add H616 compatible string Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-15 11:06 ` [PATCH v7 09/19] net: stmmac: dwmac-sun8i: Prepare for second EMAC clock register Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-15 11:06 ` [PATCH v7 10/19] dt-bindings: usb: Add H616 compatible string Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-15 11:06 ` [PATCH v7 11/19] dt-bindings: usb: sunxi-musb: " Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-15 11:06 ` [PATCH v7 12/19] phy: sun4i-usb: Rework HCI PHY (aka. "pmu_unk1") handling Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-15 11:06 ` [PATCH v7 13/19] phy: sun4i-usb: Allow reset line to be shared Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-15 11:25 ` Philipp Zabel 2021-06-15 11:25 ` Philipp Zabel 2021-06-15 11:25 ` Philipp Zabel 2021-06-15 11:25 ` Philipp Zabel 2021-06-15 11:06 ` [PATCH v7 14/19] phy: sun4i-usb: Introduce port2 SIDDQ quirk Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-21 4:36 ` Vinod Koul 2021-06-21 4:36 ` Vinod Koul 2021-06-21 4:36 ` Vinod Koul 2021-06-21 9:14 ` Andre Przywara 2021-06-21 9:14 ` Andre Przywara 2021-06-21 9:14 ` Andre Przywara 2021-06-15 11:06 ` [PATCH v7 15/19] phy: sun4i-usb: Add support for the H616 USB PHY Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-07-12 16:50 ` Evgeny Boger 2021-07-12 16:50 ` Evgeny Boger 2021-07-12 16:50 ` Evgeny Boger 2021-06-15 11:06 ` [PATCH v7 16/19] arm64: dts: allwinner: Add Allwinner H616 .dtsi file Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-16 9:23 ` Maxime Ripard 2021-06-16 9:23 ` Maxime Ripard 2021-06-16 10:06 ` Andre Przywara 2021-06-16 10:06 ` Andre Przywara 2021-06-17 15:42 ` Maxime Ripard 2021-06-17 15:42 ` Maxime Ripard 2021-06-17 15:47 ` Jernej Škrabec 2021-06-17 15:47 ` Jernej Škrabec 2021-06-15 11:06 ` [PATCH v7 17/19] dt-bindings: arm: sunxi: Add two H616 board compatible strings Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-16 17:38 ` Rob Herring 2021-06-16 17:38 ` Rob Herring 2021-06-15 11:06 ` [PATCH v7 18/19] arm64: dts: allwinner: h616: Add OrangePi Zero 2 board support Andre Przywara 2021-06-15 11:06 ` Andre Przywara 2021-06-15 11:06 ` Andre Przywara [this message] 2021-06-15 11:06 ` [PATCH v7 19/19] arm64: dts: allwinner: h616: Add X96 Mate TV box support Andre Przywara
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20210615110636.23403-20-andre.przywara@arm.com \ --to=andre.przywara@arm.com \ --cc=devicetree@vger.kernel.org \ --cc=icenowy@aosc.io \ --cc=jernej.skrabec@gmail.com \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-sunxi@googlegroups.com \ --cc=linux-sunxi@lists.linux.dev \ --cc=megous@megous.com \ --cc=mripard@kernel.org \ --cc=robh@kernel.org \ --cc=samuel@sholland.org \ --cc=wens@csie.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.