From: Judith Mendez <jm@ti.com> To: Rob Herring <robh+dt@kernel.org>, Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>, Conor Dooley <conor+dt@kernel.org> Cc: Nishanth Menon <nm@ti.com>, Vignesh Raghavendra <vigneshr@ti.com>, Tero Kristo <kristo@kernel.org>, <linux-arm-kernel@lists.infradead.org>, <devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>, Wadim Egorov <w.egorov@phytec.de>, Francesco Dolcini <francesco.dolcini@toradex.com> Subject: [PATCH v3 0/9] Fix MMC properties on Sitara K3 devices Date: Tue, 13 Feb 2024 17:56:52 -0600 [thread overview] Message-ID: <20240213235701.2438513-1-jm@ti.com> (raw) This patch series aims to fix and update MMC nodes for TI Sitara K3 devices with the following changes. The series introduces sdhci0 and sdhci2 nodes and enables eMMC for AM62ax platform. Also introduce fixes for MMC ITAP/OTAP values for AM64x platform according to device datasheet [0], and add ITAP/ OTAP values for AM62p to enable the highest timing possible for MMC0 and MMC1, according to device datasheet [1]. The DLL properties ti,trm-icp and ti,driver-strength-ohm should be removed for soft PHYs since drive strength cannot be changed, so remove these properties when not applicable. Since this fix touches non-TI boards and therefore cannot be tested, all tested-by's are welcome. Also include a few fixes for ti,clkbuf-sel, bus-width, and bootph-all device tree properties in MMC nodes. This series was tested on: - AM62a SK - AM62x SK - AM62p SK - AM64x GP EVM - AM64x SK EVM - Beagleplay [0] https://www.ti.com/lit/ds/symlink/am6442.pdf [1] https://www.ti.com/lit/ds/symlink/am62p.pdf Fixes since V2: - Remove ti,driver-strength-ohm property in sdhci1 node for k3-am642-tqma64xxl-mbax4xxl and k3-am642-phyboard-electra-rdk board files. - Add Francesco's Acked-by V2: https://lore.kernel.org/linux-devicetree/20240213002416.1560357-1-jm@ti.com/ V1: https://lore.kernel.org/linux-devicetree/22af7436-8833-4049-bdbb-f79bb3314ee8@ti.com/ RFC: https://lore.kernel.org/linux-devicetree/c94b7399-31c0-4e7d-a616-8f29c86a27ba@ti.com/ Judith Mendez (7): arm64: dts: ti: k3-am62a-main: Add sdhci2 instance arm64: dts: ti: k3-am64-main: Fix ITAP/OTAP values for MMC arm64: dts: ti: k3-am62p: Add ITAP/OTAP values for MMC arm64: dts: ti: k3-am6*: Remove DLL properties for soft PHYs arm64: dts: ti: k3-am6*: Fix ti,clkbuf-sel property in MMC nodes arm64: dts: ti: k3-am6*: Fix bus-width property in MMC nodes arm64: dts: ti: k3-am6*: Add bootph-all property in MMC node Nitin Yadav (2): arm64: dts: ti: k3-am62a-main: Add sdhci0 instance arm64: dts: ti: k3-am62a7-sk: Enable eMMC support arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 12 +++-- .../boot/dts/ti/k3-am62-phycore-som.dtsi | 1 - .../boot/dts/ti/k3-am62-verdin-dahlia.dtsi | 1 - .../arm64/boot/dts/ti/k3-am62-verdin-dev.dtsi | 1 - .../boot/dts/ti/k3-am62-verdin-wifi.dtsi | 1 - arch/arm64/boot/dts/ti/k3-am62-verdin.dtsi | 2 - .../arm64/boot/dts/ti/k3-am625-beagleplay.dts | 4 -- .../dts/ti/k3-am625-phyboard-lyra-rdk.dts | 1 - arch/arm64/boot/dts/ti/k3-am62a-main.dtsi | 45 ++++++++++++++++++- arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 27 ++++++++++- arch/arm64/boot/dts/ti/k3-am62p-main.dtsi | 44 ++++++++++++++++-- arch/arm64/boot/dts/ti/k3-am62p5-sk.dts | 3 +- .../arm64/boot/dts/ti/k3-am62x-sk-common.dtsi | 2 - arch/arm64/boot/dts/ti/k3-am64-main.dtsi | 15 +++++-- arch/arm64/boot/dts/ti/k3-am642-evm.dts | 4 +- .../dts/ti/k3-am642-phyboard-electra-rdk.dts | 1 - arch/arm64/boot/dts/ti/k3-am642-sk.dts | 2 - .../dts/ti/k3-am642-tqma64xxl-mbax4xxl.dts | 1 - 18 files changed, 129 insertions(+), 38 deletions(-) base-commit: 1e6bbc5185bcd113c8d2f7aa0a02f588a6bdbe5d -- 2.43.0 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
WARNING: multiple messages have this Message-ID (diff)
From: Judith Mendez <jm@ti.com> To: Rob Herring <robh+dt@kernel.org>, Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>, Conor Dooley <conor+dt@kernel.org> Cc: Nishanth Menon <nm@ti.com>, Vignesh Raghavendra <vigneshr@ti.com>, Tero Kristo <kristo@kernel.org>, <linux-arm-kernel@lists.infradead.org>, <devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>, Wadim Egorov <w.egorov@phytec.de>, Francesco Dolcini <francesco.dolcini@toradex.com> Subject: [PATCH v3 0/9] Fix MMC properties on Sitara K3 devices Date: Tue, 13 Feb 2024 17:56:52 -0600 [thread overview] Message-ID: <20240213235701.2438513-1-jm@ti.com> (raw) This patch series aims to fix and update MMC nodes for TI Sitara K3 devices with the following changes. The series introduces sdhci0 and sdhci2 nodes and enables eMMC for AM62ax platform. Also introduce fixes for MMC ITAP/OTAP values for AM64x platform according to device datasheet [0], and add ITAP/ OTAP values for AM62p to enable the highest timing possible for MMC0 and MMC1, according to device datasheet [1]. The DLL properties ti,trm-icp and ti,driver-strength-ohm should be removed for soft PHYs since drive strength cannot be changed, so remove these properties when not applicable. Since this fix touches non-TI boards and therefore cannot be tested, all tested-by's are welcome. Also include a few fixes for ti,clkbuf-sel, bus-width, and bootph-all device tree properties in MMC nodes. This series was tested on: - AM62a SK - AM62x SK - AM62p SK - AM64x GP EVM - AM64x SK EVM - Beagleplay [0] https://www.ti.com/lit/ds/symlink/am6442.pdf [1] https://www.ti.com/lit/ds/symlink/am62p.pdf Fixes since V2: - Remove ti,driver-strength-ohm property in sdhci1 node for k3-am642-tqma64xxl-mbax4xxl and k3-am642-phyboard-electra-rdk board files. - Add Francesco's Acked-by V2: https://lore.kernel.org/linux-devicetree/20240213002416.1560357-1-jm@ti.com/ V1: https://lore.kernel.org/linux-devicetree/22af7436-8833-4049-bdbb-f79bb3314ee8@ti.com/ RFC: https://lore.kernel.org/linux-devicetree/c94b7399-31c0-4e7d-a616-8f29c86a27ba@ti.com/ Judith Mendez (7): arm64: dts: ti: k3-am62a-main: Add sdhci2 instance arm64: dts: ti: k3-am64-main: Fix ITAP/OTAP values for MMC arm64: dts: ti: k3-am62p: Add ITAP/OTAP values for MMC arm64: dts: ti: k3-am6*: Remove DLL properties for soft PHYs arm64: dts: ti: k3-am6*: Fix ti,clkbuf-sel property in MMC nodes arm64: dts: ti: k3-am6*: Fix bus-width property in MMC nodes arm64: dts: ti: k3-am6*: Add bootph-all property in MMC node Nitin Yadav (2): arm64: dts: ti: k3-am62a-main: Add sdhci0 instance arm64: dts: ti: k3-am62a7-sk: Enable eMMC support arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 12 +++-- .../boot/dts/ti/k3-am62-phycore-som.dtsi | 1 - .../boot/dts/ti/k3-am62-verdin-dahlia.dtsi | 1 - .../arm64/boot/dts/ti/k3-am62-verdin-dev.dtsi | 1 - .../boot/dts/ti/k3-am62-verdin-wifi.dtsi | 1 - arch/arm64/boot/dts/ti/k3-am62-verdin.dtsi | 2 - .../arm64/boot/dts/ti/k3-am625-beagleplay.dts | 4 -- .../dts/ti/k3-am625-phyboard-lyra-rdk.dts | 1 - arch/arm64/boot/dts/ti/k3-am62a-main.dtsi | 45 ++++++++++++++++++- arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 27 ++++++++++- arch/arm64/boot/dts/ti/k3-am62p-main.dtsi | 44 ++++++++++++++++-- arch/arm64/boot/dts/ti/k3-am62p5-sk.dts | 3 +- .../arm64/boot/dts/ti/k3-am62x-sk-common.dtsi | 2 - arch/arm64/boot/dts/ti/k3-am64-main.dtsi | 15 +++++-- arch/arm64/boot/dts/ti/k3-am642-evm.dts | 4 +- .../dts/ti/k3-am642-phyboard-electra-rdk.dts | 1 - arch/arm64/boot/dts/ti/k3-am642-sk.dts | 2 - .../dts/ti/k3-am642-tqma64xxl-mbax4xxl.dts | 1 - 18 files changed, 129 insertions(+), 38 deletions(-) base-commit: 1e6bbc5185bcd113c8d2f7aa0a02f588a6bdbe5d -- 2.43.0
next reply other threads:[~2024-02-13 23:58 UTC|newest] Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top 2024-02-13 23:56 Judith Mendez [this message] 2024-02-13 23:56 ` [PATCH v3 0/9] Fix MMC properties on Sitara K3 devices Judith Mendez 2024-02-13 23:56 ` [PATCH v3 1/9] arm64: dts: ti: k3-am62a-main: Add sdhci0 instance Judith Mendez 2024-02-13 23:56 ` Judith Mendez 2024-02-13 23:56 ` [PATCH v3 2/9] arm64: dts: ti: k3-am62a-main: Add sdhci2 instance Judith Mendez 2024-02-13 23:56 ` Judith Mendez 2024-02-13 23:56 ` [PATCH v3 3/9] arm64: dts: ti: k3-am62a7-sk: Enable eMMC support Judith Mendez 2024-02-13 23:56 ` Judith Mendez 2024-02-13 23:56 ` [PATCH v3 4/9] arm64: dts: ti: k3-am64-main: Fix ITAP/OTAP values for MMC Judith Mendez 2024-02-13 23:56 ` Judith Mendez 2024-02-13 23:56 ` [PATCH v3 5/9] arm64: dts: ti: k3-am62p: Add " Judith Mendez 2024-02-13 23:56 ` Judith Mendez 2024-02-13 23:56 ` [PATCH v3 6/9] arm64: dts: ti: k3-am6*: Remove DLL properties for soft PHYs Judith Mendez 2024-02-13 23:56 ` Judith Mendez 2024-02-13 23:56 ` [PATCH v3 7/9] arm64: dts: ti: k3-am6*: Fix ti,clkbuf-sel property in MMC nodes Judith Mendez 2024-02-13 23:56 ` Judith Mendez 2024-02-13 23:57 ` [PATCH v3 8/9] arm64: dts: ti: k3-am6*: Fix bus-width " Judith Mendez 2024-02-13 23:57 ` Judith Mendez 2024-02-13 23:57 ` [PATCH v3 9/9] arm64: dts: ti: k3-am6*: Add bootph-all property in MMC node Judith Mendez 2024-02-13 23:57 ` Judith Mendez 2024-02-14 10:26 ` [PATCH v3 0/9] Fix MMC properties on Sitara K3 devices Wadim Egorov 2024-02-14 10:26 ` Wadim Egorov 2024-02-20 4:03 ` Vignesh Raghavendra 2024-02-20 4:03 ` Vignesh Raghavendra
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=20240213235701.2438513-1-jm@ti.com \ --to=jm@ti.com \ --cc=conor+dt@kernel.org \ --cc=devicetree@vger.kernel.org \ --cc=francesco.dolcini@toradex.com \ --cc=kristo@kernel.org \ --cc=krzysztof.kozlowski+dt@linaro.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-kernel@vger.kernel.org \ --cc=nm@ti.com \ --cc=robh+dt@kernel.org \ --cc=vigneshr@ti.com \ --cc=w.egorov@phytec.de \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.