[PATCH 07/11] arm64: dts: renesas: Extract common Salvator-X/XS board support

From: Simon Horman <horms+renesas@verge.net.au>
To: linux-renesas-soc@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org,
	Magnus Damm <magnus.damm@gmail.com>,
	Geert Uytterhoeven <geert+renesas@glider.be>,
	Simon Horman <horms+renesas@verge.net.au>
Subject: [PATCH 07/11] arm64: dts: renesas: Extract common Salvator-X/XS board support
Date: Fri, 16 Jun 2017 15:30:15 +0200	[thread overview]
Message-ID: <5fe6a7d8f14e54e009668a543aefa55e904cfe03.1497617276.git.horms+renesas@verge.net.au> (raw)
In-Reply-To: <cover.1497617276.git.horms+renesas@verge.net.au>

From: Geert Uytterhoeven <geert+renesas@glider.be>

The Renesas Salvator-X and Salvator-XS (Salvator-X 2nd version) boards
are very similar.  To avoid duplication, prepare for the advent of the
latter by extracting the common board parts into its own .dtsi file.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
 arch/arm64/boot/dts/renesas/salvator-common.dtsi | 629 +++++++++++++++++++++++
 arch/arm64/boot/dts/renesas/salvator-x.dtsi      | 616 +---------------------
 2 files changed, 630 insertions(+), 615 deletions(-)
 create mode 100644 arch/arm64/boot/dts/renesas/salvator-common.dtsi

diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
new file mode 100644
index 000000000000..aef35e0b685a
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
@@ -0,0 +1,629 @@
+/*
+ * Device Tree Source for common parts of Salvator-X board variants
+ *
+ * Copyright (C) 2015-2016 Renesas Electronics Corp.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/*
+ * SSI-AK4613
+ *
+ * This command is required when Playback/Capture
+ *
+ *	amixer set "DVC Out" 100%
+ *	amixer set "DVC In" 100%
+ *
+ * You can use Mute
+ *
+ *	amixer set "DVC Out Mute" on
+ *	amixer set "DVC In Mute" on
+ *
+ * You can use Volume Ramp
+ *
+ *	amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
+ *	amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
+ *	amixer set "DVC Out Ramp" on
+ *	aplay xxx.wav &
+ *	amixer set "DVC Out"  80%  // Volume Down
+ *	amixer set "DVC Out" 100%  // Volume Up
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	aliases {
+		serial0 = &scif2;
+		serial1 = &scif1;
+		ethernet0 = &avb;
+	};
+
+	chosen {
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
+		stdout-path = "serial0:115200n8";
+	};
+
+	audio_clkout: audio_clkout {
+		/*
+		 * This is same as <&rcar_sound 0>
+		 * but needed to avoid cs2000/rcar_sound probe dead-lock
+		 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <11289600>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 50000>;
+
+		brightness-levels = <256 128 64 16 8 4 0>;
+		default-brightness-level = <6>;
+
+		enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_1p8v: regulator0 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator1 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	rsnd_ak4613: sound {
+		compatible = "simple-audio-card";
+
+		simple-audio-card,format = "left_j";
+		simple-audio-card,bitclock-master = <&sndcpu>;
+		simple-audio-card,frame-master = <&sndcpu>;
+
+		sndcpu: simple-audio-card,cpu {
+			sound-dai = <&rcar_sound>;
+		};
+
+		sndcodec: simple-audio-card,codec {
+			sound-dai = <&ak4613>;
+		};
+	};
+
+	vbus0_usb2: regulator-vbus0-usb2 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "USB20_VBUS0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vcc_sdhi0: regulator-vcc-sdhi0 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "SDHI0 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vccq_sdhi0: regulator-vccq-sdhi0 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI0 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1
+			  1800000 0>;
+	};
+
+	vcc_sdhi3: regulator-vcc-sdhi3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "SDHI3 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vccq_sdhi3: regulator-vccq-sdhi3 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI3 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+		gpios-states = <1>;
+		states = <3300000 1
+			  1800000 0>;
+	};
+
+	hdmi0-out {
+		compatible = "hdmi-connector";
+		label = "HDMI0 OUT";
+		type = "a";
+
+		port {
+			hdmi0_con: endpoint {
+			};
+		};
+	};
+
+	hdmi1-out {
+		compatible = "hdmi-connector";
+		label = "HDMI1 OUT";
+		type = "a";
+
+		port {
+			hdmi1_con: endpoint {
+			};
+		};
+	};
+
+	vga {
+		compatible = "vga-connector";
+
+		port {
+			vga_in: endpoint {
+				remote-endpoint = <&adv7123_out>;
+			};
+		};
+	};
+
+	vga-encoder {
+		compatible = "adi,adv7123";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7123_in: endpoint {
+					remote-endpoint = <&du_out_rgb>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				adv7123_out: endpoint {
+					remote-endpoint = <&vga_in>;
+				};
+			};
+		};
+	};
+
+	x12_clk: x12 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+
+	/* External DU dot clocks */
+	x21_clk: x21-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <33000000>;
+	};
+
+	x22_clk: x22-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <33000000>;
+	};
+
+	x23_clk: x23-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+};
+
+&audio_clk_a {
+	clock-frequency = <22579200>;
+};
+
+&avb {
+	pinctrl-0 = <&avb_pins>;
+	pinctrl-names = "default";
+	renesas,no-ether-link;
+	phy-handle = <&phy0>;
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		rxc-skew-ps = <1500>;
+		reg = <0>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&du {
+	pinctrl-0 = <&du_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	ports {
+		port@0 {
+			endpoint {
+				remote-endpoint = <&adv7123_in>;
+			};
+		};
+		port@3 {
+			lvds_connector: endpoint {
+			};
+		};
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&extalr_clk {
+	clock-frequency = <32768>;
+};
+
+&hsusb {
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-0 = <&i2c2_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	clock-frequency = <100000>;
+
+	ak4613: codec@10 {
+		compatible = "asahi-kasei,ak4613";
+		#sound-dai-cells = <0>;
+		reg = <0x10>;
+		clocks = <&rcar_sound 3>;
+
+		asahi-kasei,in1-single-end;
+		asahi-kasei,in2-single-end;
+		asahi-kasei,out1-single-end;
+		asahi-kasei,out2-single-end;
+		asahi-kasei,out3-single-end;
+		asahi-kasei,out4-single-end;
+		asahi-kasei,out5-single-end;
+		asahi-kasei,out6-single-end;
+	};
+
+	cs2000: clk_multiplier@4f {
+		#clock-cells = <0>;
+		compatible = "cirrus,cs2000-cp";
+		reg = <0x4f>;
+		clocks = <&audio_clkout>, <&x12_clk>;
+		clock-names = "clk_in", "ref_clk";
+
+		assigned-clocks = <&cs2000>;
+		assigned-clock-rates = <24576000>; /* 1/1 divide */
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	csa_vdd: adc@7c {
+		compatible = "maxim,max9611";
+		reg = <0x7c>;
+
+		shunt-resistor-micro-ohms = <5000>;
+	};
+
+	csa_dvfs: adc@7f {
+		compatible = "maxim,max9611";
+		reg = <0x7f>;
+
+		shunt-resistor-micro-ohms = <5000>;
+	};
+};
+
+&i2c_dvfs {
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&pcie_bus_clk {
+	clock-frequency = <100000000>;
+};
+
+&pciec0 {
+	status = "okay";
+};
+
+&pciec1 {
+	status = "okay";
+};
+
+&pfc {
+	pinctrl-0 = <&scif_clk_pins>;
+	pinctrl-names = "default";
+
+	avb_pins: avb {
+		mux {
+			groups = "avb_link", "avb_phy_int", "avb_mdc",
+				 "avb_mii";
+			function = "avb";
+		};
+
+		pins_mdc {
+			groups = "avb_mdc";
+			drive-strength = <24>;
+		};
+
+		pins_mii_tx {
+			pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
+			       "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
+			drive-strength = <12>;
+		};
+	};
+
+	du_pins: du {
+		groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0";
+		function = "du";
+	};
+
+	i2c2_pins: i2c2 {
+		groups = "i2c2_a";
+		function = "i2c2";
+	};
+
+	pwm1_pins: pwm1 {
+		groups = "pwm1_a";
+		function = "pwm1";
+	};
+
+	scif1_pins: scif1 {
+		groups = "scif1_data_a", "scif1_ctrl";
+		function = "scif1";
+	};
+
+	scif2_pins: scif2 {
+		groups = "scif2_data_a";
+		function = "scif2";
+	};
+
+	scif_clk_pins: scif_clk {
+		groups = "scif_clk_a";
+		function = "scif_clk";
+	};
+
+	sdhi0_pins: sd0 {
+		groups = "sdhi0_data4", "sdhi0_ctrl";
+		function = "sdhi0";
+		power-source = <3300>;
+	};
+
+	sdhi0_pins_uhs: sd0_uhs {
+		groups = "sdhi0_data4", "sdhi0_ctrl";
+		function = "sdhi0";
+		power-source = <1800>;
+	};
+
+	sdhi2_pins: sd2 {
+		groups = "sdhi2_data8", "sdhi2_ctrl";
+		function = "sdhi2";
+		power-source = <3300>;
+	};
+
+	sdhi2_pins_uhs: sd2_uhs {
+		groups = "sdhi2_data8", "sdhi2_ctrl";
+		function = "sdhi2";
+		power-source = <1800>;
+	};
+
+	sdhi3_pins: sd3 {
+		groups = "sdhi3_data4", "sdhi3_ctrl";
+		function = "sdhi3";
+		power-source = <3300>;
+	};
+
+	sdhi3_pins_uhs: sd3_uhs {
+		groups = "sdhi3_data4", "sdhi3_ctrl";
+		function = "sdhi3";
+		power-source = <1800>;
+	};
+
+	sound_pins: sound {
+		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
+		function = "ssi";
+	};
+
+	sound_clk_pins: sound_clk {
+		groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
+			 "audio_clkout_a", "audio_clkout3_a";
+		function = "audio_clk";
+	};
+
+	usb0_pins: usb0 {
+		groups = "usb0";
+		function = "usb0";
+	};
+
+	usb1_pins: usb1 {
+		mux {
+			groups = "usb1";
+			function = "usb1";
+		};
+
+		ovc {
+			pins = "GP_6_27";
+			bias-pull-up;
+		};
+
+		pwen {
+			pins = "GP_6_26";
+			bias-pull-down;
+		};
+	};
+};
+
+&pwm1 {
+	pinctrl-0 = <&pwm1_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&rcar_sound {
+	pinctrl-0 = <&sound_pins &sound_clk_pins>;
+	pinctrl-names = "default";
+
+	/* Single DAI */
+	#sound-dai-cells = <0>;
+
+	/* audio_clkout0/1/2/3 */
+	#clock-cells = <1>;
+	clock-frequency = <11289600 12288000>;
+
+	status = "okay";
+
+	/* update <audio_clk_b> to <cs2000> */
+	clocks = <&cpg CPG_MOD 1005>,
+		 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
+		 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
+		 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
+		 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
+		 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
+		 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
+		 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
+		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
+		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
+		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
+		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
+		 <&audio_clk_a>, <&cs2000>,
+		 <&audio_clk_c>,
+		 <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
+
+	rcar_sound,dai {
+		dai0 {
+			playback = <&ssi0 &src0 &dvc0>;
+			capture  = <&ssi1 &src1 &dvc1>;
+		};
+	};
+};
+
+&scif1 {
+	pinctrl-0 = <&scif1_pins>;
+	pinctrl-names = "default";
+
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&scif2 {
+	pinctrl-0 = <&scif2_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&scif_clk {
+	clock-frequency = <14745600>;
+};
+
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_pins>;
+	pinctrl-1 = <&sdhi0_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&vcc_sdhi0>;
+	vqmmc-supply = <&vccq_sdhi0>;
+	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	status = "okay";
+};
+
+&sdhi2 {
+	/* used for on-board 8bit eMMC */
+	pinctrl-0 = <&sdhi2_pins>;
+	pinctrl-1 = <&sdhi2_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	status = "okay";
+};
+
+&sdhi3 {
+	pinctrl-0 = <&sdhi3_pins>;
+	pinctrl-1 = <&sdhi3_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&vcc_sdhi3>;
+	vqmmc-supply = <&vccq_sdhi3>;
+	cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	status = "okay";
+};
+
+&ssi1 {
+	shared-pin;
+};
+
+&usb2_phy0 {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+
+	vbus-supply = <&vbus0_usb2>;
+	status = "okay";
+};
+
+&usb2_phy1 {
+	pinctrl-0 = <&usb1_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&wdt0 {
+	timeout-sec = <60>;
+	status = "okay";
+};
+
+&xhci0 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/renesas/salvator-x.dtsi b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
index 2f5386252aed..468868c8ed9f 100644
--- a/arch/arm64/boot/dts/renesas/salvator-x.dtsi
+++ b/arch/arm64/boot/dts/renesas/salvator-x.dtsi
@@ -8,335 +8,18 @@
  * kind, whether express or implied.
  */
 
-/*
- * SSI-AK4613
- *
- * This command is required when Playback/Capture
- *
- *	amixer set "DVC Out" 100%
- *	amixer set "DVC In" 100%
- *
- * You can use Mute
- *
- *	amixer set "DVC Out Mute" on
- *	amixer set "DVC In Mute" on
- *
- * You can use Volume Ramp
- *
- *	amixer set "DVC Out Ramp Up Rate"   "0.125 dB/64 steps"
- *	amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
- *	amixer set "DVC Out Ramp" on
- *	aplay xxx.wav &
- *	amixer set "DVC Out"  80%  // Volume Down
- *	amixer set "DVC Out" 100%  // Volume Up
- */
-
-#include <dt-bindings/gpio/gpio.h>
+#include "salvator-common.dtsi"
 
 / {
 	model = "Renesas Salvator-X board";
 	compatible = "renesas,salvator-x";
-
-	aliases {
-		serial0 = &scif2;
-		serial1 = &scif1;
-		ethernet0 = &avb;
-	};
-
-	chosen {
-		bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
-		stdout-path = "serial0:115200n8";
-	};
-
-	audio_clkout: audio_clkout {
-		/*
-		 * This is same as <&rcar_sound 0>
-		 * but needed to avoid cs2000/rcar_sound probe dead-lock
-		 */
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <11289600>;
-	};
-
-	backlight: backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm1 0 50000>;
-
-		brightness-levels = <256 128 64 16 8 4 0>;
-		default-brightness-level = <6>;
-
-		enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
-	};
-
-	reg_1p8v: regulator0 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-1.8V";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	reg_3p3v: regulator1 {
-		compatible = "regulator-fixed";
-		regulator-name = "fixed-3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	rsnd_ak4613: sound {
-		compatible = "simple-audio-card";
-
-		simple-audio-card,format = "left_j";
-		simple-audio-card,bitclock-master = <&sndcpu>;
-		simple-audio-card,frame-master = <&sndcpu>;
-
-		sndcpu: simple-audio-card,cpu {
-			sound-dai = <&rcar_sound>;
-		};
-
-		sndcodec: simple-audio-card,codec {
-			sound-dai = <&ak4613>;
-		};
-	};
-
-	vbus0_usb2: regulator-vbus0-usb2 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "USB20_VBUS0";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-
-		gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vcc_sdhi0: regulator-vcc-sdhi0 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "SDHI0 Vcc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vccq_sdhi0: regulator-vccq-sdhi0 {
-		compatible = "regulator-gpio";
-
-		regulator-name = "SDHI0 VccQ";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
-		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
-	};
-
-	vcc_sdhi3: regulator-vcc-sdhi3 {
-		compatible = "regulator-fixed";
-
-		regulator-name = "SDHI3 Vcc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vccq_sdhi3: regulator-vccq-sdhi3 {
-		compatible = "regulator-gpio";
-
-		regulator-name = "SDHI3 VccQ";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
-		gpios-states = <1>;
-		states = <3300000 1
-			  1800000 0>;
-	};
-
-	hdmi0-out {
-		compatible = "hdmi-connector";
-		label = "HDMI0 OUT";
-		type = "a";
-
-		port {
-			hdmi0_con: endpoint {
-			};
-		};
-	};
-
-	hdmi1-out {
-		compatible = "hdmi-connector";
-		label = "HDMI1 OUT";
-		type = "a";
-
-		port {
-			hdmi1_con: endpoint {
-			};
-		};
-	};
-
-	vga {
-		compatible = "vga-connector";
-
-		port {
-			vga_in: endpoint {
-				remote-endpoint = <&adv7123_out>;
-			};
-		};
-	};
-
-	vga-encoder {
-		compatible = "adi,adv7123";
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				adv7123_in: endpoint {
-					remote-endpoint = <&du_out_rgb>;
-				};
-			};
-			port@1 {
-				reg = <1>;
-				adv7123_out: endpoint {
-					remote-endpoint = <&vga_in>;
-				};
-			};
-		};
-	};
-
-	x12_clk: x12 {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <24576000>;
-	};
-
-	/* External DU dot clocks */
-	x21_clk: x21-clock {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <33000000>;
-	};
-
-	x22_clk: x22-clock {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <33000000>;
-	};
-
-	x23_clk: x23-clock {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <25000000>;
-	};
-};
-
-&audio_clk_a {
-	clock-frequency = <22579200>;
-};
-
-&avb {
-	pinctrl-0 = <&avb_pins>;
-	pinctrl-names = "default";
-	renesas,no-ether-link;
-	phy-handle = <&phy0>;
-	status = "okay";
-
-	phy0: ethernet-phy@0 {
-		rxc-skew-ps = <1500>;
-		reg = <0>;
-		interrupt-parent = <&gpio2>;
-		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
-	};
-};
-
-&du {
-	pinctrl-0 = <&du_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	ports {
-		port@0 {
-			endpoint {
-				remote-endpoint = <&adv7123_in>;
-			};
-		};
-		port@3 {
-			lvds_connector: endpoint {
-			};
-		};
-	};
-};
-
-&ehci0 {
-	status = "okay";
-};
-
-&ehci1 {
-	status = "okay";
 };
 
 &extal_clk {
 	clock-frequency = <16666666>;
 };
 
-&extalr_clk {
-	clock-frequency = <32768>;
-};
-
-&hsusb {
-	status = "okay";
-};
-
-&i2c2 {
-	pinctrl-0 = <&i2c2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-
-	clock-frequency = <100000>;
-
-	ak4613: codec@10 {
-		compatible = "asahi-kasei,ak4613";
-		#sound-dai-cells = <0>;
-		reg = <0x10>;
-		clocks = <&rcar_sound 3>;
-
-		asahi-kasei,in1-single-end;
-		asahi-kasei,in2-single-end;
-		asahi-kasei,out1-single-end;
-		asahi-kasei,out2-single-end;
-		asahi-kasei,out3-single-end;
-		asahi-kasei,out4-single-end;
-		asahi-kasei,out5-single-end;
-		asahi-kasei,out6-single-end;
-	};
-
-	cs2000: clk_multiplier@4f {
-		#clock-cells = <0>;
-		compatible = "cirrus,cs2000-cp";
-		reg = <0x4f>;
-		clocks = <&audio_clkout>, <&x12_clk>;
-		clock-names = "clk_in", "ref_clk";
-
-		assigned-clocks = <&cs2000>;
-		assigned-clock-rates = <24576000>; /* 1/1 divide */
-	};
-};
-
 &i2c4 {
-	status = "okay";
-
 	versaclock5: clock-generator@6a {
 		compatible = "idt,5p49v5923";
 		reg = <0x6a>;
@@ -344,301 +27,4 @@
 		clocks = <&x23_clk>;
 		clock-names = "xin";
 	};
-
-	csa_vdd: adc@7c {
-		compatible = "maxim,max9611";
-		reg = <0x7c>;
-
-		shunt-resistor-micro-ohms = <5000>;
-	};
-
-	csa_dvfs: adc@7f {
-		compatible = "maxim,max9611";
-		reg = <0x7f>;
-
-		shunt-resistor-micro-ohms = <5000>;
-	};
-};
-
-&i2c_dvfs {
-	status = "okay";
-};
-
-&ohci0 {
-	status = "okay";
-};
-
-&ohci1 {
-	status = "okay";
-};
-
-&pcie_bus_clk {
-	clock-frequency = <100000000>;
-};
-
-&pciec0 {
-	status = "okay";
-};
-
-&pciec1 {
-	status = "okay";
-};
-
-&pfc {
-	pinctrl-0 = <&scif_clk_pins>;
-	pinctrl-names = "default";
-
-	avb_pins: avb {
-		mux {
-			groups = "avb_link", "avb_phy_int", "avb_mdc",
-				 "avb_mii";
-			function = "avb";
-		};
-
-		pins_mdc {
-			groups = "avb_mdc";
-			drive-strength = <24>;
-		};
-
-		pins_mii_tx {
-			pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
-			       "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
-			drive-strength = <12>;
-		};
-	};
-
-	du_pins: du {
-		groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0";
-		function = "du";
-	};
-
-	i2c2_pins: i2c2 {
-		groups = "i2c2_a";
-		function = "i2c2";
-	};
-
-	pwm1_pins: pwm1 {
-		groups = "pwm1_a";
-		function = "pwm1";
-	};
-
-	scif1_pins: scif1 {
-		groups = "scif1_data_a", "scif1_ctrl";
-		function = "scif1";
-	};
-
-	scif2_pins: scif2 {
-		groups = "scif2_data_a";
-		function = "scif2";
-	};
-
-	scif_clk_pins: scif_clk {
-		groups = "scif_clk_a";
-		function = "scif_clk";
-	};
-
-	sdhi0_pins: sd0 {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <3300>;
-	};
-
-	sdhi0_pins_uhs: sd0_uhs {
-		groups = "sdhi0_data4", "sdhi0_ctrl";
-		function = "sdhi0";
-		power-source = <1800>;
-	};
-
-	sdhi2_pins: sd2 {
-		groups = "sdhi2_data8", "sdhi2_ctrl";
-		function = "sdhi2";
-		power-source = <3300>;
-	};
-
-	sdhi2_pins_uhs: sd2_uhs {
-		groups = "sdhi2_data8", "sdhi2_ctrl";
-		function = "sdhi2";
-		power-source = <1800>;
-	};
-
-	sdhi3_pins: sd3 {
-		groups = "sdhi3_data4", "sdhi3_ctrl";
-		function = "sdhi3";
-		power-source = <3300>;
-	};
-
-	sdhi3_pins_uhs: sd3_uhs {
-		groups = "sdhi3_data4", "sdhi3_ctrl";
-		function = "sdhi3";
-		power-source = <1800>;
-	};
-
-	sound_pins: sound {
-		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
-		function = "ssi";
-	};
-
-	sound_clk_pins: sound_clk {
-		groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
-			 "audio_clkout_a", "audio_clkout3_a";
-		function = "audio_clk";
-	};
-
-	usb0_pins: usb0 {
-		groups = "usb0";
-		function = "usb0";
-	};
-
-	usb1_pins: usb1 {
-		mux {
-			groups = "usb1";
-			function = "usb1";
-		};
-
-		ovc {
-			pins = "GP_6_27";
-			bias-pull-up;
-		};
-
-		pwen {
-			pins = "GP_6_26";
-			bias-pull-down;
-		};
-	};
-};
-
-&pwm1 {
-	pinctrl-0 = <&pwm1_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&rcar_sound {
-	pinctrl-0 = <&sound_pins &sound_clk_pins>;
-	pinctrl-names = "default";
-
-	/* Single DAI */
-	#sound-dai-cells = <0>;
-
-	/* audio_clkout0/1/2/3 */
-	#clock-cells = <1>;
-	clock-frequency = <11289600 12288000>;
-
-	status = "okay";
-
-	/* update <audio_clk_b> to <cs2000> */
-	clocks = <&cpg CPG_MOD 1005>,
-		 <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
-		 <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
-		 <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
-		 <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
-		 <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
-		 <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
-		 <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
-		 <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
-		 <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
-		 <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
-		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
-		 <&audio_clk_a>, <&cs2000>,
-		 <&audio_clk_c>,
-		 <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
-
-	rcar_sound,dai {
-		dai0 {
-			playback = <&ssi0 &src0 &dvc0>;
-			capture  = <&ssi1 &src1 &dvc1>;
-		};
-	};
-};
-
-&scif1 {
-	pinctrl-0 = <&scif1_pins>;
-	pinctrl-names = "default";
-
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&scif2 {
-	pinctrl-0 = <&scif2_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&scif_clk {
-	clock-frequency = <14745600>;
-};
-
-&sdhi0 {
-	pinctrl-0 = <&sdhi0_pins>;
-	pinctrl-1 = <&sdhi0_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&vcc_sdhi0>;
-	vqmmc-supply = <&vccq_sdhi0>;
-	cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
-	bus-width = <4>;
-	sd-uhs-sdr50;
-	status = "okay";
-};
-
-&sdhi2 {
-	/* used for on-board 8bit eMMC */
-	pinctrl-0 = <&sdhi2_pins>;
-	pinctrl-1 = <&sdhi2_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&reg_3p3v>;
-	vqmmc-supply = <&reg_1p8v>;
-	bus-width = <8>;
-	mmc-hs200-1_8v;
-	non-removable;
-	status = "okay";
-};
-
-&sdhi3 {
-	pinctrl-0 = <&sdhi3_pins>;
-	pinctrl-1 = <&sdhi3_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&vcc_sdhi3>;
-	vqmmc-supply = <&vccq_sdhi3>;
-	cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
-	bus-width = <4>;
-	sd-uhs-sdr50;
-	status = "okay";
-};
-
-&ssi1 {
-	shared-pin;
-};
-
-&usb2_phy0 {
-	pinctrl-0 = <&usb0_pins>;
-	pinctrl-names = "default";
-
-	vbus-supply = <&vbus0_usb2>;
-	status = "okay";
-};
-
-&usb2_phy1 {
-	pinctrl-0 = <&usb1_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&wdt0 {
-	timeout-sec = <60>;
-	status = "okay";
-};
-
-&xhci0 {
-	status = "okay";
 };
-- 
2.1.4
