From: Arend Van Spriel <arend.vanspriel@broadcom.com>
To: "Rafał Miłecki" <zajec5@gmail.com>, "Kalle Valo" <kvalo@codeaurora.org>
Cc: Brett Rudley <brudley@broadcom.com>,
Arend van Spriel <arend@broadcom.com>,
"Franky (Zhenhui) Lin" <frankyl@broadcom.com>,
Hante Meuleman <meuleman@broadcom.com>,
Pieter-Paul Giesberts <pieterpg@broadcom.com>,
"open list:BROADCOM BRCM80211 IEEE802.11n WIRELESS DRIVER"
<linux-wireless@vger.kernel.org>,
"open list:BROADCOM BRCM80211 IEEE802.11n WIRELESS DRIVER"
<brcm80211-dev-list@broadcom.com>,
"open list:NETWORKING DRIVERS" <netdev@vger.kernel.org>,
open list <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH 4.8 1/2] brcmutil: add field storing control channel to the struct brcmu_chan
Date: Fri, 20 May 2016 09:52:02 +0200 [thread overview]
Message-ID: <097733a4-091b-69c8-7e12-52764f0c8ca1@broadcom.com> (raw)
In-Reply-To: <1463655770-22467-1-git-send-email-zajec5@gmail.com>
On 19-5-2016 13:02, Rafał Miłecki wrote:
> Our d11 code supports encoding/decoding channel info into/from chanspec
> format used by firmware. Current implementation is quite misleading
> because of the way "chnum" field is used.
> When encoding channel info, "chnum" has to be filled by a caller with
> *center* channel number. However when decoding chanspec the same field
> is filled with a *control* channel number.
>
> This can be confusing and doesn't allow accessing all info when
> decoding. Solve it by adding a separated field for control channel.
The need to "access all info" is probably the other patch so you might
hint here that this change is needed for the .get_channel() callback.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
> Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
> ---
> .../broadcom/brcm80211/brcmfmac/cfg80211.c | 17 +++++++++--------
> .../net/wireless/broadcom/brcm80211/brcmfmac/p2p.c | 10 +++++-----
> .../net/wireless/broadcom/brcm80211/brcmutil/d11.c | 18 ++++++++++--------
> .../broadcom/brcm80211/include/brcmu_d11.h | 22 ++++++++++++++++++++++
> 4 files changed, 46 insertions(+), 21 deletions(-)
>
> diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c
> index d0631b6..597495d 100644
> --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c
> +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c
> @@ -2734,7 +2734,7 @@ static s32 brcmf_inform_single_bss(struct brcmf_cfg80211_info *cfg,
> if (!bi->ctl_ch) {
> ch.chspec = le16_to_cpu(bi->chanspec);
> cfg->d11inf.decchspec(&ch);
> - bi->ctl_ch = ch.chnum;
> + bi->ctl_ch = ch.control_ch_num;
> }
> channel = bi->ctl_ch;
>
> @@ -2852,7 +2852,7 @@ static s32 brcmf_inform_ibss(struct brcmf_cfg80211_info *cfg,
> else
> band = wiphy->bands[NL80211_BAND_5GHZ];
>
> - freq = ieee80211_channel_to_frequency(ch.chnum, band->band);
> + freq = ieee80211_channel_to_frequency(ch.control_ch_num, band->band);
> cfg->channel = freq;
> notify_channel = ieee80211_get_channel(wiphy, freq);
>
> @@ -2862,7 +2862,7 @@ static s32 brcmf_inform_ibss(struct brcmf_cfg80211_info *cfg,
> notify_ielen = le32_to_cpu(bi->ie_length);
> notify_signal = (s16)le16_to_cpu(bi->RSSI) * 100;
>
> - brcmf_dbg(CONN, "channel: %d(%d)\n", ch.chnum, freq);
> + brcmf_dbg(CONN, "channel: %d(%d)\n", ch.control_ch_num, freq);
> brcmf_dbg(CONN, "capability: %X\n", notify_capability);
> brcmf_dbg(CONN, "beacon interval: %d\n", notify_interval);
> brcmf_dbg(CONN, "signal: %d\n", notify_signal);
> @@ -5280,7 +5280,7 @@ brcmf_bss_roaming_done(struct brcmf_cfg80211_info *cfg,
> else
> band = wiphy->bands[NL80211_BAND_5GHZ];
>
> - freq = ieee80211_channel_to_frequency(ch.chnum, band->band);
> + freq = ieee80211_channel_to_frequency(ch.control_ch_num, band->band);
> notify_channel = ieee80211_get_channel(wiphy, freq);
>
> done:
> @@ -5802,14 +5802,15 @@ static int brcmf_construct_chaninfo(struct brcmf_cfg80211_info *cfg,
> channel = band->channels;
> index = band->n_channels;
> for (j = 0; j < band->n_channels; j++) {
> - if (channel[j].hw_value == ch.chnum) {
> + if (channel[j].hw_value == ch.control_ch_num) {
> index = j;
> break;
> }
> }
> channel[index].center_freq =
> - ieee80211_channel_to_frequency(ch.chnum, band->band);
> - channel[index].hw_value = ch.chnum;
> + ieee80211_channel_to_frequency(ch.control_ch_num,
> + band->band);
> + channel[index].hw_value = ch.control_ch_num;
>
> /* assuming the chanspecs order is HT20,
> * HT40 upper, HT40 lower, and VHT80.
> @@ -5911,7 +5912,7 @@ static int brcmf_enable_bw40_2g(struct brcmf_cfg80211_info *cfg)
> if (WARN_ON(ch.bw != BRCMU_CHAN_BW_40))
> continue;
> for (j = 0; j < band->n_channels; j++) {
> - if (band->channels[j].hw_value == ch.chnum)
> + if (band->channels[j].hw_value == ch.control_ch_num)
> break;
> }
> if (WARN_ON(j == band->n_channels))
> diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c
> index a70cda6..1652a48 100644
> --- a/drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c
> +++ b/drivers/net/wireless/broadcom/brcm80211/brcmfmac/p2p.c
> @@ -1246,7 +1246,7 @@ bool brcmf_p2p_scan_finding_common_channel(struct brcmf_cfg80211_info *cfg,
> if (!bi->ctl_ch) {
> ch.chspec = le16_to_cpu(bi->chanspec);
> cfg->d11inf.decchspec(&ch);
> - bi->ctl_ch = ch.chnum;
> + bi->ctl_ch = ch.control_ch_num;
> }
> afx_hdl->peer_chan = bi->ctl_ch;
> brcmf_dbg(TRACE, "ACTION FRAME SCAN : Peer %pM found, channel : %d\n",
> @@ -1385,7 +1385,7 @@ int brcmf_p2p_notify_action_frame_rx(struct brcmf_if *ifp,
> if (test_bit(BRCMF_P2P_STATUS_FINDING_COMMON_CHANNEL,
> &p2p->status) &&
> (ether_addr_equal(afx_hdl->tx_dst_addr, e->addr))) {
> - afx_hdl->peer_chan = ch.chnum;
> + afx_hdl->peer_chan = ch.control_ch_num;
> brcmf_dbg(INFO, "GON request: Peer found, channel=%d\n",
> afx_hdl->peer_chan);
> complete(&afx_hdl->act_frm_scan);
> @@ -1428,7 +1428,7 @@ int brcmf_p2p_notify_action_frame_rx(struct brcmf_if *ifp,
> memcpy(&mgmt_frame->u, frame, mgmt_frame_len);
> mgmt_frame_len += offsetof(struct ieee80211_mgmt, u);
>
> - freq = ieee80211_channel_to_frequency(ch.chnum,
> + freq = ieee80211_channel_to_frequency(ch.control_ch_num,
> ch.band == BRCMU_CHAN_BAND_2G ?
> NL80211_BAND_2GHZ :
> NL80211_BAND_5GHZ);
> @@ -1873,7 +1873,7 @@ s32 brcmf_p2p_notify_rx_mgmt_p2p_probereq(struct brcmf_if *ifp,
>
> if (test_bit(BRCMF_P2P_STATUS_FINDING_COMMON_CHANNEL, &p2p->status) &&
> (ether_addr_equal(afx_hdl->tx_dst_addr, e->addr))) {
> - afx_hdl->peer_chan = ch.chnum;
> + afx_hdl->peer_chan = ch.control_ch_num;
> brcmf_dbg(INFO, "PROBE REQUEST: Peer found, channel=%d\n",
> afx_hdl->peer_chan);
> complete(&afx_hdl->act_frm_scan);
> @@ -1898,7 +1898,7 @@ s32 brcmf_p2p_notify_rx_mgmt_p2p_probereq(struct brcmf_if *ifp,
>
> mgmt_frame = (u8 *)(rxframe + 1);
> mgmt_frame_len = e->datalen - sizeof(*rxframe);
> - freq = ieee80211_channel_to_frequency(ch.chnum,
> + freq = ieee80211_channel_to_frequency(ch.control_ch_num,
> ch.band == BRCMU_CHAN_BAND_2G ?
> NL80211_BAND_2GHZ :
> NL80211_BAND_5GHZ);
> diff --git a/drivers/net/wireless/broadcom/brcm80211/brcmutil/d11.c b/drivers/net/wireless/broadcom/brcm80211/brcmutil/d11.c
> index 2b2522b..d8b79cb 100644
> --- a/drivers/net/wireless/broadcom/brcm80211/brcmutil/d11.c
> +++ b/drivers/net/wireless/broadcom/brcm80211/brcmutil/d11.c
> @@ -107,6 +107,7 @@ static void brcmu_d11n_decchspec(struct brcmu_chan *ch)
> u16 val;
>
> ch->chnum = (u8)(ch->chspec & BRCMU_CHSPEC_CH_MASK);
> + ch->control_ch_num = ch->chnum;
>
> switch (ch->chspec & BRCMU_CHSPEC_D11N_BW_MASK) {
> case BRCMU_CHSPEC_D11N_BW_20:
> @@ -118,10 +119,10 @@ static void brcmu_d11n_decchspec(struct brcmu_chan *ch)
> val = ch->chspec & BRCMU_CHSPEC_D11N_SB_MASK;
> if (val == BRCMU_CHSPEC_D11N_SB_L) {
> ch->sb = BRCMU_CHAN_SB_L;
> - ch->chnum -= CH_10MHZ_APART;
> + ch->control_ch_num -= CH_10MHZ_APART;
> } else {
> ch->sb = BRCMU_CHAN_SB_U;
> - ch->chnum += CH_10MHZ_APART;
> + ch->control_ch_num += CH_10MHZ_APART;
> }
> break;
> default:
> @@ -147,6 +148,7 @@ static void brcmu_d11ac_decchspec(struct brcmu_chan *ch)
> u16 val;
>
> ch->chnum = (u8)(ch->chspec & BRCMU_CHSPEC_CH_MASK);
> + ch->control_ch_num = ch->chnum;
>
> switch (ch->chspec & BRCMU_CHSPEC_D11AC_BW_MASK) {
> case BRCMU_CHSPEC_D11AC_BW_20:
> @@ -158,10 +160,10 @@ static void brcmu_d11ac_decchspec(struct brcmu_chan *ch)
> val = ch->chspec & BRCMU_CHSPEC_D11AC_SB_MASK;
> if (val == BRCMU_CHSPEC_D11AC_SB_L) {
> ch->sb = BRCMU_CHAN_SB_L;
> - ch->chnum -= CH_10MHZ_APART;
> + ch->control_ch_num -= CH_10MHZ_APART;
> } else if (val == BRCMU_CHSPEC_D11AC_SB_U) {
> ch->sb = BRCMU_CHAN_SB_U;
> - ch->chnum += CH_10MHZ_APART;
> + ch->control_ch_num += CH_10MHZ_APART;
> } else {
> WARN_ON_ONCE(1);
> }
> @@ -172,16 +174,16 @@ static void brcmu_d11ac_decchspec(struct brcmu_chan *ch)
> BRCMU_CHSPEC_D11AC_SB_SHIFT);
> switch (ch->sb) {
> case BRCMU_CHAN_SB_LL:
> - ch->chnum -= CH_30MHZ_APART;
> + ch->control_ch_num -= CH_30MHZ_APART;
> break;
> case BRCMU_CHAN_SB_LU:
> - ch->chnum -= CH_10MHZ_APART;
> + ch->control_ch_num -= CH_10MHZ_APART;
> break;
> case BRCMU_CHAN_SB_UL:
> - ch->chnum += CH_10MHZ_APART;
> + ch->control_ch_num += CH_10MHZ_APART;
> break;
> case BRCMU_CHAN_SB_UU:
> - ch->chnum += CH_30MHZ_APART;
> + ch->control_ch_num += CH_30MHZ_APART;
> break;
> default:
> WARN_ON_ONCE(1);
> diff --git a/drivers/net/wireless/broadcom/brcm80211/include/brcmu_d11.h b/drivers/net/wireless/broadcom/brcm80211/include/brcmu_d11.h
> index f9745ea..8b8b2ec 100644
> --- a/drivers/net/wireless/broadcom/brcm80211/include/brcmu_d11.h
> +++ b/drivers/net/wireless/broadcom/brcm80211/include/brcmu_d11.h
> @@ -125,14 +125,36 @@ enum brcmu_chan_sb {
> BRCMU_CHAN_SB_UU = BRCMU_CHAN_SB_LUU,
> };
>
> +/**
> + * struct brcmu_chan - stores channel formats
> + *
> + * This structure can be used with functions translating chanspec into generic
> + * channel info and the other way.
> + *
> + * @chspec: firmware specific format
> + * @chnum: center channel number
> + * @control_ch_num: control channel number
> + * @band: frequency band
> + * @bw: channel width
> + * @sb: control sideband (location of control channel against the center one)
> + */
> struct brcmu_chan {
> u16 chspec;
> u8 chnum;
> + u8 control_ch_num;
> u8 band;
> enum brcmu_chan_bw bw;
> enum brcmu_chan_sb sb;
> };
>
> +/**
> + * struct brcmu_d11inf - provides functions translating channel formats
> + *
> + * @io_type: determines version of channel format used by firmware
> + * @encchspec: encodes channel info into a chanspec, requires center channel
> + * number, ignores control one
> + * @decchspec: decodes chanspec into generic info
> + */
> struct brcmu_d11inf {
> u8 io_type;
>
>
next prev parent reply other threads:[~2016-05-20 7:52 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-05-19 11:02 [PATCH 4.8 1/2] brcmutil: add field storing control channel to the struct brcmu_chan Rafał Miłecki
2016-05-19 11:02 ` [PATCH 4.8 2/2] brcmfmac: support get_channel cfg80211 callback Rafał Miłecki
2016-05-20 7:42 ` Arend Van Spriel
2016-05-20 7:42 ` Arend Van Spriel
2016-05-20 10:54 ` Rafał Miłecki
2016-05-20 10:54 ` Rafał Miłecki
2016-05-20 10:54 ` Rafał Miłecki
2016-05-20 7:52 ` Arend Van Spriel [this message]
2016-05-20 7:52 ` [PATCH 4.8 1/2] brcmutil: add field storing control channel to the struct brcmu_chan Arend Van Spriel
2016-05-20 11:38 ` [PATCH V2 " Rafał Miłecki
2016-05-20 11:38 ` [PATCH V2 4.8 2/2] brcmfmac: support get_channel cfg80211 callback Rafał Miłecki
2016-05-20 11:38 ` Rafał Miłecki
2016-06-14 14:28 ` [V2, 4.8, 1/2] brcmutil: add field storing control channel to the struct brcmu_chan Kalle Valo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=097733a4-091b-69c8-7e12-52764f0c8ca1@broadcom.com \
--to=arend.vanspriel@broadcom.com \
--cc=arend@broadcom.com \
--cc=brcm80211-dev-list@broadcom.com \
--cc=brudley@broadcom.com \
--cc=frankyl@broadcom.com \
--cc=kvalo@codeaurora.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-wireless@vger.kernel.org \
--cc=meuleman@broadcom.com \
--cc=netdev@vger.kernel.org \
--cc=pieterpg@broadcom.com \
--cc=zajec5@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.