* [PATCH] arm64: zynqmp: Move USB3 PHY properties from DWC3 node to USB node
@ 2021-07-19 11:31 Michal Simek
2021-07-26 7:26 ` Michal Simek
0 siblings, 1 reply; 2+ messages in thread
From: Michal Simek @ 2021-07-19 11:31 UTC (permalink / raw)
To: u-boot, git; +Cc: Manish Narani
From: Manish Narani <manish.narani@xilinx.com>
Move the PHY properties from DWC3 node to USB node in ZynqMP DTs as here
the USB3 PHY used is PSGTR, which is connected to Xilinx USB core. This
PHY initialization should be handled from Xilinx USB core as the
prerequisite register configurations are done here only.
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
---
arch/arm/dts/zynqmp-p-a2197-00-revA.dts | 4 ++--
arch/arm/dts/zynqmp-sck-kv-g-revA.dts | 4 ++--
arch/arm/dts/zynqmp-sck-kv-g-revB.dts | 4 ++--
arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts | 4 ++--
arch/arm/dts/zynqmp-zc1751-xm017-dc3.dts | 8 ++++----
arch/arm/dts/zynqmp-zcu100-revC.dts | 8 ++++----
arch/arm/dts/zynqmp-zcu102-revA.dts | 4 ++--
arch/arm/dts/zynqmp-zcu104-revA.dts | 4 ++--
arch/arm/dts/zynqmp-zcu104-revC.dts | 4 ++--
arch/arm/dts/zynqmp-zcu106-revA.dts | 4 ++--
arch/arm/dts/zynqmp-zcu111-revA.dts | 4 ++--
arch/arm/dts/zynqmp-zcu208-revA.dts | 4 ++--
arch/arm/dts/zynqmp-zcu216-revA.dts | 4 ++--
13 files changed, 30 insertions(+), 30 deletions(-)
diff --git a/arch/arm/dts/zynqmp-p-a2197-00-revA.dts b/arch/arm/dts/zynqmp-p-a2197-00-revA.dts
index d50b335e674d..c893aaaafd8f 100644
--- a/arch/arm/dts/zynqmp-p-a2197-00-revA.dts
+++ b/arch/arm/dts/zynqmp-p-a2197-00-revA.dts
@@ -545,6 +545,8 @@
status = "okay";
xlnx,usb-polarity = <0>;
xlnx,usb-reset-mode = <0>;
+ phy-names = "usb3-phy";
+ phys = <&psgtr 1 PHY_TYPE_USB3 0 1>;
};
&dwc3_0 {
@@ -553,8 +555,6 @@
snps,dis_u2_susphy_quirk;
snps,dis_u3_susphy_quirk;
maximum-speed = "super-speed";
- phy-names = "usb3-phy";
- phys = <&psgtr 1 PHY_TYPE_USB3 0 1>;
};
&usb1 {
diff --git a/arch/arm/dts/zynqmp-sck-kv-g-revA.dts b/arch/arm/dts/zynqmp-sck-kv-g-revA.dts
index 59d5751e0634..4e8086c82f23 100644
--- a/arch/arm/dts/zynqmp-sck-kv-g-revA.dts
+++ b/arch/arm/dts/zynqmp-sck-kv-g-revA.dts
@@ -125,6 +125,8 @@
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb0_default>;
+ phy-names = "usb3-phy";
+ phys = <&psgtr 2 PHY_TYPE_USB3 0 1>;
usbhub: usb5744 { /* u43 */
compatible = "microchip,usb5744";
reset-gpios = <&gpio 44 GPIO_ACTIVE_HIGH>;
@@ -135,8 +137,6 @@
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&psgtr 2 PHY_TYPE_USB3 0 1>;
maximum-speed = "super-speed";
};
diff --git a/arch/arm/dts/zynqmp-sck-kv-g-revB.dts b/arch/arm/dts/zynqmp-sck-kv-g-revB.dts
index b5443afff982..048d5665c57b 100644
--- a/arch/arm/dts/zynqmp-sck-kv-g-revB.dts
+++ b/arch/arm/dts/zynqmp-sck-kv-g-revB.dts
@@ -109,14 +109,14 @@
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb0_default>;
+ phy-names = "usb3-phy";
+ phys = <&psgtr 2 PHY_TYPE_USB3 0 1>;
};
&dwc3_0 {
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&psgtr 2 PHY_TYPE_USB3 0 1>;
maximum-speed = "super-speed";
};
diff --git a/arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts b/arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts
index b92a2ee3e60a..4a87bd6a6aaf 100644
--- a/arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts
+++ b/arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts
@@ -424,14 +424,14 @@
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb0_default>;
+ phy-names = "usb3-phy";
+ phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
};
&dwc3_0 {
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
maximum-speed = "super-speed";
};
diff --git a/arch/arm/dts/zynqmp-zc1751-xm017-dc3.dts b/arch/arm/dts/zynqmp-zc1751-xm017-dc3.dts
index 344323ab7f93..13812470ae34 100644
--- a/arch/arm/dts/zynqmp-zc1751-xm017-dc3.dts
+++ b/arch/arm/dts/zynqmp-zc1751-xm017-dc3.dts
@@ -221,27 +221,27 @@
&usb0 {
status = "okay";
+ phy-names = "usb3-phy";
+ phys = <&psgtr 0 PHY_TYPE_USB3 0 2>;
};
&dwc3_0 {
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&psgtr 0 PHY_TYPE_USB3 0 2>;
maximum-speed = "super-speed";
};
/* ULPI SMSC USB3320 */
&usb1 {
status = "okay";
+ phy-names = "usb3-phy";
+ phys = <&psgtr 3 PHY_TYPE_USB3 1 2>;
};
&dwc3_1 {
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&psgtr 3 PHY_TYPE_USB3 1 2>;
maximum-speed = "super-speed";
};
diff --git a/arch/arm/dts/zynqmp-zcu100-revC.dts b/arch/arm/dts/zynqmp-zcu100-revC.dts
index 2d615774782f..ea630a43dc7f 100644
--- a/arch/arm/dts/zynqmp-zcu100-revC.dts
+++ b/arch/arm/dts/zynqmp-zcu100-revC.dts
@@ -561,13 +561,13 @@
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb0_default>;
+ phy-names = "usb3-phy";
+ phys = <&psgtr 2 PHY_TYPE_USB3 0 0>;
};
&dwc3_0 {
status = "okay";
dr_mode = "peripheral";
- phy-names = "usb3-phy";
- phys = <&psgtr 2 PHY_TYPE_USB3 0 0>;
maximum-speed = "super-speed";
};
@@ -576,13 +576,13 @@
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb1_default>;
+ phy-names = "usb3-phy";
+ phys = <&psgtr 3 PHY_TYPE_USB3 1 0>;
};
&dwc3_1 {
status = "okay";
dr_mode = "host";
- phy-names = "usb3-phy";
- phys = <&psgtr 3 PHY_TYPE_USB3 1 0>;
maximum-speed = "super-speed";
};
diff --git a/arch/arm/dts/zynqmp-zcu102-revA.dts b/arch/arm/dts/zynqmp-zcu102-revA.dts
index 1d4a9cdc69f0..175252d2def2 100644
--- a/arch/arm/dts/zynqmp-zcu102-revA.dts
+++ b/arch/arm/dts/zynqmp-zcu102-revA.dts
@@ -1035,14 +1035,14 @@
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb0_default>;
+ phy-names = "usb3-phy";
+ phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
};
&dwc3_0 {
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
maximum-speed = "super-speed";
};
diff --git a/arch/arm/dts/zynqmp-zcu104-revA.dts b/arch/arm/dts/zynqmp-zcu104-revA.dts
index 7e5eca82fdaa..9cd30447eb3e 100644
--- a/arch/arm/dts/zynqmp-zcu104-revA.dts
+++ b/arch/arm/dts/zynqmp-zcu104-revA.dts
@@ -502,14 +502,14 @@
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb0_default>;
+ phy-names = "usb3-phy";
+ phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
};
&dwc3_0 {
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
maximum-speed = "super-speed";
};
diff --git a/arch/arm/dts/zynqmp-zcu104-revC.dts b/arch/arm/dts/zynqmp-zcu104-revC.dts
index f4ebcbb318b4..45191569c101 100644
--- a/arch/arm/dts/zynqmp-zcu104-revC.dts
+++ b/arch/arm/dts/zynqmp-zcu104-revC.dts
@@ -514,14 +514,14 @@
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb0_default>;
+ phy-names = "usb3-phy";
+ phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
};
&dwc3_0 {
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
maximum-speed = "super-speed";
};
diff --git a/arch/arm/dts/zynqmp-zcu106-revA.dts b/arch/arm/dts/zynqmp-zcu106-revA.dts
index ac6689c16730..50cc72eb9240 100644
--- a/arch/arm/dts/zynqmp-zcu106-revA.dts
+++ b/arch/arm/dts/zynqmp-zcu106-revA.dts
@@ -1012,14 +1012,14 @@
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb0_default>;
+ phy-names = "usb3-phy";
+ phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
};
&dwc3_0 {
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
maximum-speed = "super-speed";
};
diff --git a/arch/arm/dts/zynqmp-zcu111-revA.dts b/arch/arm/dts/zynqmp-zcu111-revA.dts
index 8d57ca2b3bf3..2b15ce1ea847 100644
--- a/arch/arm/dts/zynqmp-zcu111-revA.dts
+++ b/arch/arm/dts/zynqmp-zcu111-revA.dts
@@ -849,14 +849,14 @@
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usb0_default>;
+ phy-names = "usb3-phy";
+ phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
};
&dwc3_0 {
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
maximum-speed = "super-speed";
};
diff --git a/arch/arm/dts/zynqmp-zcu208-revA.dts b/arch/arm/dts/zynqmp-zcu208-revA.dts
index d3e20ae85d7e..32a6e6fb55e2 100644
--- a/arch/arm/dts/zynqmp-zcu208-revA.dts
+++ b/arch/arm/dts/zynqmp-zcu208-revA.dts
@@ -692,13 +692,13 @@
/* ULPI SMSC USB3320 */
&usb0 {
status = "okay";
+ phy-names = "usb3-phy";
+ phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
};
&dwc3_0 {
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
maximum-speed = "super-speed";
};
diff --git a/arch/arm/dts/zynqmp-zcu216-revA.dts b/arch/arm/dts/zynqmp-zcu216-revA.dts
index ae7c18196894..1e347036d0a7 100644
--- a/arch/arm/dts/zynqmp-zcu216-revA.dts
+++ b/arch/arm/dts/zynqmp-zcu216-revA.dts
@@ -696,13 +696,13 @@
/* ULPI SMSC USB3320 */
&usb0 {
status = "okay";
+ phy-names = "usb3-phy";
+ phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
};
&dwc3_0 {
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
- phy-names = "usb3-phy";
- phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
maximum-speed = "super-speed";
};
--
2.32.0
^ permalink raw reply related [flat|nested] 2+ messages in thread
* Re: [PATCH] arm64: zynqmp: Move USB3 PHY properties from DWC3 node to USB node
2021-07-19 11:31 [PATCH] arm64: zynqmp: Move USB3 PHY properties from DWC3 node to USB node Michal Simek
@ 2021-07-26 7:26 ` Michal Simek
0 siblings, 0 replies; 2+ messages in thread
From: Michal Simek @ 2021-07-26 7:26 UTC (permalink / raw)
To: U-Boot, git; +Cc: Manish Narani
po 19. 7. 2021 v 13:31 odesílatel Michal Simek <michal.simek@xilinx.com> napsal:
>
> From: Manish Narani <manish.narani@xilinx.com>
>
> Move the PHY properties from DWC3 node to USB node in ZynqMP DTs as here
> the USB3 PHY used is PSGTR, which is connected to Xilinx USB core. This
> PHY initialization should be handled from Xilinx USB core as the
> prerequisite register configurations are done here only.
>
> Signed-off-by: Manish Narani <manish.narani@xilinx.com>
> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
> ---
>
> arch/arm/dts/zynqmp-p-a2197-00-revA.dts | 4 ++--
> arch/arm/dts/zynqmp-sck-kv-g-revA.dts | 4 ++--
> arch/arm/dts/zynqmp-sck-kv-g-revB.dts | 4 ++--
> arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts | 4 ++--
> arch/arm/dts/zynqmp-zc1751-xm017-dc3.dts | 8 ++++----
> arch/arm/dts/zynqmp-zcu100-revC.dts | 8 ++++----
> arch/arm/dts/zynqmp-zcu102-revA.dts | 4 ++--
> arch/arm/dts/zynqmp-zcu104-revA.dts | 4 ++--
> arch/arm/dts/zynqmp-zcu104-revC.dts | 4 ++--
> arch/arm/dts/zynqmp-zcu106-revA.dts | 4 ++--
> arch/arm/dts/zynqmp-zcu111-revA.dts | 4 ++--
> arch/arm/dts/zynqmp-zcu208-revA.dts | 4 ++--
> arch/arm/dts/zynqmp-zcu216-revA.dts | 4 ++--
> 13 files changed, 30 insertions(+), 30 deletions(-)
>
> diff --git a/arch/arm/dts/zynqmp-p-a2197-00-revA.dts b/arch/arm/dts/zynqmp-p-a2197-00-revA.dts
> index d50b335e674d..c893aaaafd8f 100644
> --- a/arch/arm/dts/zynqmp-p-a2197-00-revA.dts
> +++ b/arch/arm/dts/zynqmp-p-a2197-00-revA.dts
> @@ -545,6 +545,8 @@
> status = "okay";
> xlnx,usb-polarity = <0>;
> xlnx,usb-reset-mode = <0>;
> + phy-names = "usb3-phy";
> + phys = <&psgtr 1 PHY_TYPE_USB3 0 1>;
> };
>
> &dwc3_0 {
> @@ -553,8 +555,6 @@
> snps,dis_u2_susphy_quirk;
> snps,dis_u3_susphy_quirk;
> maximum-speed = "super-speed";
> - phy-names = "usb3-phy";
> - phys = <&psgtr 1 PHY_TYPE_USB3 0 1>;
> };
>
> &usb1 {
> diff --git a/arch/arm/dts/zynqmp-sck-kv-g-revA.dts b/arch/arm/dts/zynqmp-sck-kv-g-revA.dts
> index 59d5751e0634..4e8086c82f23 100644
> --- a/arch/arm/dts/zynqmp-sck-kv-g-revA.dts
> +++ b/arch/arm/dts/zynqmp-sck-kv-g-revA.dts
> @@ -125,6 +125,8 @@
> status = "okay";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_usb0_default>;
> + phy-names = "usb3-phy";
> + phys = <&psgtr 2 PHY_TYPE_USB3 0 1>;
> usbhub: usb5744 { /* u43 */
> compatible = "microchip,usb5744";
> reset-gpios = <&gpio 44 GPIO_ACTIVE_HIGH>;
> @@ -135,8 +137,6 @@
> status = "okay";
> dr_mode = "host";
> snps,usb3_lpm_capable;
> - phy-names = "usb3-phy";
> - phys = <&psgtr 2 PHY_TYPE_USB3 0 1>;
> maximum-speed = "super-speed";
> };
>
> diff --git a/arch/arm/dts/zynqmp-sck-kv-g-revB.dts b/arch/arm/dts/zynqmp-sck-kv-g-revB.dts
> index b5443afff982..048d5665c57b 100644
> --- a/arch/arm/dts/zynqmp-sck-kv-g-revB.dts
> +++ b/arch/arm/dts/zynqmp-sck-kv-g-revB.dts
> @@ -109,14 +109,14 @@
> status = "okay";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_usb0_default>;
> + phy-names = "usb3-phy";
> + phys = <&psgtr 2 PHY_TYPE_USB3 0 1>;
> };
>
> &dwc3_0 {
> status = "okay";
> dr_mode = "host";
> snps,usb3_lpm_capable;
> - phy-names = "usb3-phy";
> - phys = <&psgtr 2 PHY_TYPE_USB3 0 1>;
> maximum-speed = "super-speed";
> };
>
> diff --git a/arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts b/arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts
> index b92a2ee3e60a..4a87bd6a6aaf 100644
> --- a/arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts
> +++ b/arch/arm/dts/zynqmp-zc1751-xm015-dc1.dts
> @@ -424,14 +424,14 @@
> status = "okay";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_usb0_default>;
> + phy-names = "usb3-phy";
> + phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
> };
>
> &dwc3_0 {
> status = "okay";
> dr_mode = "host";
> snps,usb3_lpm_capable;
> - phy-names = "usb3-phy";
> - phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
> maximum-speed = "super-speed";
> };
>
> diff --git a/arch/arm/dts/zynqmp-zc1751-xm017-dc3.dts b/arch/arm/dts/zynqmp-zc1751-xm017-dc3.dts
> index 344323ab7f93..13812470ae34 100644
> --- a/arch/arm/dts/zynqmp-zc1751-xm017-dc3.dts
> +++ b/arch/arm/dts/zynqmp-zc1751-xm017-dc3.dts
> @@ -221,27 +221,27 @@
>
> &usb0 {
> status = "okay";
> + phy-names = "usb3-phy";
> + phys = <&psgtr 0 PHY_TYPE_USB3 0 2>;
> };
>
> &dwc3_0 {
> status = "okay";
> dr_mode = "host";
> snps,usb3_lpm_capable;
> - phy-names = "usb3-phy";
> - phys = <&psgtr 0 PHY_TYPE_USB3 0 2>;
> maximum-speed = "super-speed";
> };
>
> /* ULPI SMSC USB3320 */
> &usb1 {
> status = "okay";
> + phy-names = "usb3-phy";
> + phys = <&psgtr 3 PHY_TYPE_USB3 1 2>;
> };
>
> &dwc3_1 {
> status = "okay";
> dr_mode = "host";
> snps,usb3_lpm_capable;
> - phy-names = "usb3-phy";
> - phys = <&psgtr 3 PHY_TYPE_USB3 1 2>;
> maximum-speed = "super-speed";
> };
> diff --git a/arch/arm/dts/zynqmp-zcu100-revC.dts b/arch/arm/dts/zynqmp-zcu100-revC.dts
> index 2d615774782f..ea630a43dc7f 100644
> --- a/arch/arm/dts/zynqmp-zcu100-revC.dts
> +++ b/arch/arm/dts/zynqmp-zcu100-revC.dts
> @@ -561,13 +561,13 @@
> status = "okay";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_usb0_default>;
> + phy-names = "usb3-phy";
> + phys = <&psgtr 2 PHY_TYPE_USB3 0 0>;
> };
>
> &dwc3_0 {
> status = "okay";
> dr_mode = "peripheral";
> - phy-names = "usb3-phy";
> - phys = <&psgtr 2 PHY_TYPE_USB3 0 0>;
> maximum-speed = "super-speed";
> };
>
> @@ -576,13 +576,13 @@
> status = "okay";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_usb1_default>;
> + phy-names = "usb3-phy";
> + phys = <&psgtr 3 PHY_TYPE_USB3 1 0>;
> };
>
> &dwc3_1 {
> status = "okay";
> dr_mode = "host";
> - phy-names = "usb3-phy";
> - phys = <&psgtr 3 PHY_TYPE_USB3 1 0>;
> maximum-speed = "super-speed";
> };
>
> diff --git a/arch/arm/dts/zynqmp-zcu102-revA.dts b/arch/arm/dts/zynqmp-zcu102-revA.dts
> index 1d4a9cdc69f0..175252d2def2 100644
> --- a/arch/arm/dts/zynqmp-zcu102-revA.dts
> +++ b/arch/arm/dts/zynqmp-zcu102-revA.dts
> @@ -1035,14 +1035,14 @@
> status = "okay";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_usb0_default>;
> + phy-names = "usb3-phy";
> + phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
> };
>
> &dwc3_0 {
> status = "okay";
> dr_mode = "host";
> snps,usb3_lpm_capable;
> - phy-names = "usb3-phy";
> - phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
> maximum-speed = "super-speed";
> };
>
> diff --git a/arch/arm/dts/zynqmp-zcu104-revA.dts b/arch/arm/dts/zynqmp-zcu104-revA.dts
> index 7e5eca82fdaa..9cd30447eb3e 100644
> --- a/arch/arm/dts/zynqmp-zcu104-revA.dts
> +++ b/arch/arm/dts/zynqmp-zcu104-revA.dts
> @@ -502,14 +502,14 @@
> status = "okay";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_usb0_default>;
> + phy-names = "usb3-phy";
> + phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
> };
>
> &dwc3_0 {
> status = "okay";
> dr_mode = "host";
> snps,usb3_lpm_capable;
> - phy-names = "usb3-phy";
> - phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
> maximum-speed = "super-speed";
> };
>
> diff --git a/arch/arm/dts/zynqmp-zcu104-revC.dts b/arch/arm/dts/zynqmp-zcu104-revC.dts
> index f4ebcbb318b4..45191569c101 100644
> --- a/arch/arm/dts/zynqmp-zcu104-revC.dts
> +++ b/arch/arm/dts/zynqmp-zcu104-revC.dts
> @@ -514,14 +514,14 @@
> status = "okay";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_usb0_default>;
> + phy-names = "usb3-phy";
> + phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
> };
>
> &dwc3_0 {
> status = "okay";
> dr_mode = "host";
> snps,usb3_lpm_capable;
> - phy-names = "usb3-phy";
> - phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
> maximum-speed = "super-speed";
> };
>
> diff --git a/arch/arm/dts/zynqmp-zcu106-revA.dts b/arch/arm/dts/zynqmp-zcu106-revA.dts
> index ac6689c16730..50cc72eb9240 100644
> --- a/arch/arm/dts/zynqmp-zcu106-revA.dts
> +++ b/arch/arm/dts/zynqmp-zcu106-revA.dts
> @@ -1012,14 +1012,14 @@
> status = "okay";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_usb0_default>;
> + phy-names = "usb3-phy";
> + phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
> };
>
> &dwc3_0 {
> status = "okay";
> dr_mode = "host";
> snps,usb3_lpm_capable;
> - phy-names = "usb3-phy";
> - phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
> maximum-speed = "super-speed";
> };
>
> diff --git a/arch/arm/dts/zynqmp-zcu111-revA.dts b/arch/arm/dts/zynqmp-zcu111-revA.dts
> index 8d57ca2b3bf3..2b15ce1ea847 100644
> --- a/arch/arm/dts/zynqmp-zcu111-revA.dts
> +++ b/arch/arm/dts/zynqmp-zcu111-revA.dts
> @@ -849,14 +849,14 @@
> status = "okay";
> pinctrl-names = "default";
> pinctrl-0 = <&pinctrl_usb0_default>;
> + phy-names = "usb3-phy";
> + phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
> };
>
> &dwc3_0 {
> status = "okay";
> dr_mode = "host";
> snps,usb3_lpm_capable;
> - phy-names = "usb3-phy";
> - phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
> maximum-speed = "super-speed";
> };
>
> diff --git a/arch/arm/dts/zynqmp-zcu208-revA.dts b/arch/arm/dts/zynqmp-zcu208-revA.dts
> index d3e20ae85d7e..32a6e6fb55e2 100644
> --- a/arch/arm/dts/zynqmp-zcu208-revA.dts
> +++ b/arch/arm/dts/zynqmp-zcu208-revA.dts
> @@ -692,13 +692,13 @@
> /* ULPI SMSC USB3320 */
> &usb0 {
> status = "okay";
> + phy-names = "usb3-phy";
> + phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
> };
>
> &dwc3_0 {
> status = "okay";
> dr_mode = "host";
> snps,usb3_lpm_capable;
> - phy-names = "usb3-phy";
> - phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
> maximum-speed = "super-speed";
> };
> diff --git a/arch/arm/dts/zynqmp-zcu216-revA.dts b/arch/arm/dts/zynqmp-zcu216-revA.dts
> index ae7c18196894..1e347036d0a7 100644
> --- a/arch/arm/dts/zynqmp-zcu216-revA.dts
> +++ b/arch/arm/dts/zynqmp-zcu216-revA.dts
> @@ -696,13 +696,13 @@
> /* ULPI SMSC USB3320 */
> &usb0 {
> status = "okay";
> + phy-names = "usb3-phy";
> + phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
> };
>
> &dwc3_0 {
> status = "okay";
> dr_mode = "host";
> snps,usb3_lpm_capable;
> - phy-names = "usb3-phy";
> - phys = <&psgtr 2 PHY_TYPE_USB3 0 2>;
> maximum-speed = "super-speed";
> };
> --
> 2.32.0
>
Applied.
M
--
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
w: www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel - Xilinx Microblaze
Maintainer of Linux kernel - Xilinx Zynq ARM and ZynqMP ARM64 SoCs
U-Boot custodian - Xilinx Microblaze/Zynq/ZynqMP/Versal SoCs
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2021-07-26 7:26 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-07-19 11:31 [PATCH] arm64: zynqmp: Move USB3 PHY properties from DWC3 node to USB node Michal Simek
2021-07-26 7:26 ` Michal Simek
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.