[U-Boot] [PATCH V6 0/5] Add Pantheon soc and dkb board support

All of lore.kernel.org
 help / color / mirror / Atom feed

* [U-Boot] [PATCH V6 0/5] Add Pantheon soc and dkb board support
@ 2011-01-25  2:40 Lei Wen
  2011-01-25  2:40 ` [U-Boot] [PATCH V6 1/5] mv: seperate kirkwood and armada from common setting Lei Wen
                   ` (10 more replies)
  0 siblings, 11 replies; 26+ messages in thread
From: Lei Wen @ 2011-01-25  2:40 UTC (permalink / raw)
  To: u-boot

This patch set add the Pantheon soc and dkb board support.

V2:
This patch seris update the seperate mv_common part as suggested.

V3:
Fix config.h include place and copyright claim year.

V4:
Add change log to each patch.

V5:
Add doc in Readme for new CONFIG_SYS_MVFS.
code style fix.

V6:
Rebase patch on latest u-boot-marvell.git.
And fix a build warning.

Lei Wen (5):
  mv: seperate kirkwood and armada from common setting
  ARM: Add Support for Marvell Pantheon Familiy SoCs
  serial: add pantheon soc support
  mvmfp: add MFP configuration support for PANTHEON
  Pantheon: Add Board Support for Marvell dkb board

 MAINTAINERS                                   |    4 +
 README                                        |    5 +
 arch/arm/cpu/arm926ejs/pantheon/Makefile      |   46 ++++++
 arch/arm/cpu/arm926ejs/pantheon/cpu.c         |   78 +++++++++
 arch/arm/cpu/arm926ejs/pantheon/dram.c        |  132 ++++++++++++++++
 arch/arm/cpu/arm926ejs/pantheon/timer.c       |  207 +++++++++++++++++++++++++
 arch/arm/include/asm/arch-armada100/config.h  |   50 ++++++
 arch/arm/include/asm/arch-kirkwood/config.h   |  145 +++++++++++++++++
 arch/arm/include/asm/arch-pantheon/config.h   |   44 ++++++
 arch/arm/include/asm/arch-pantheon/cpu.h      |   79 ++++++++++
 arch/arm/include/asm/arch-pantheon/mfp.h      |   41 +++++
 arch/arm/include/asm/arch-pantheon/pantheon.h |   54 +++++++
 board/Marvell/dkb/Makefile                    |   51 ++++++
 board/Marvell/dkb/dkb.c                       |   54 +++++++
 boards.cfg                                    |    1 +
 drivers/gpio/mvmfp.c                          |    2 +
 drivers/serial/serial.c                       |    2 +
 include/configs/aspenite.h                    |    1 +
 include/configs/dkb.h                         |   62 ++++++++
 include/configs/mv-common.h                   |  147 +++---------------
 20 files changed, 1079 insertions(+), 126 deletions(-)
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/Makefile
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/cpu.c
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/dram.c
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/timer.c
 create mode 100644 arch/arm/include/asm/arch-armada100/config.h
 create mode 100644 arch/arm/include/asm/arch-kirkwood/config.h
 create mode 100644 arch/arm/include/asm/arch-pantheon/config.h
 create mode 100644 arch/arm/include/asm/arch-pantheon/cpu.h
 create mode 100644 arch/arm/include/asm/arch-pantheon/mfp.h
 create mode 100644 arch/arm/include/asm/arch-pantheon/pantheon.h
 create mode 100644 board/Marvell/dkb/Makefile
 create mode 100644 board/Marvell/dkb/dkb.c
 create mode 100644 include/configs/dkb.h

^ permalink raw reply	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V6 1/5] mv: seperate kirkwood and armada from common setting
  2011-01-25  2:40 [U-Boot] [PATCH V6 0/5] Add Pantheon soc and dkb board support Lei Wen
@ 2011-01-25  2:40 ` Lei Wen
  2011-01-25  2:40 ` [U-Boot] [PATCH V6 2/5] ARM: Add Support for Marvell Pantheon Familiy SoCs Lei Wen
                   ` (9 subsequent siblings)
  10 siblings, 0 replies; 26+ messages in thread
From: Lei Wen @ 2011-01-25  2:40 UTC (permalink / raw)
  To: u-boot

Since there are lots of difference between kirkwood and armada series,
it is better to seperate them but still keep the most common file
shared by all marvell platform in the mv-common configure file.

This patch move the kirkwood only driver definitoin in mv-common to
the <soc_name>/config.h.

This patch is tested with compilation for armada100 and guruplug.

Signed-off-by: Lei Wen <leiwen@marvell.com>
---
V2:
This patch seris update the seperate mv_common part as suggested.

V3:
Fix config.h include place and copyright claim year.

V4:
Add change log to each patch.

V5:
Add CONFIG_SYS_MVFS doc in README.

V6:
Rebase patch on latest u-boot-marvell.git.

 README                                       |    5 +
 arch/arm/include/asm/arch-armada100/config.h |   50 +++++++++
 arch/arm/include/asm/arch-kirkwood/config.h  |  145 +++++++++++++++++++++++++
 include/configs/aspenite.h                   |    1 +
 include/configs/mv-common.h                  |  147 ++++----------------------
 5 files changed, 222 insertions(+), 126 deletions(-)
 create mode 100644 arch/arm/include/asm/arch-armada100/config.h
 create mode 100644 arch/arm/include/asm/arch-kirkwood/config.h

diff --git a/README b/README
index 755d17c..e0341b5 100644
--- a/README
+++ b/README
@@ -319,6 +319,11 @@ The following options need to be configured:
 			CONFIG_SYS_PQ2FADS	- PQ2FADS-ZU or PQ2FADS-VR
 			CONFIG_SYS_8272ADS	- MPC8272ADS
 
+- Marvell Family Member
+		CONFIG_SYS_MVFS		- define it if you want to enable
+					  multiply fs option at one time
+					  for marvell soc family
+
 - MPC824X Family Member (if CONFIG_MPC824X is defined)
 		Define exactly one of
 		CONFIG_MPC8240, CONFIG_MPC8245
diff --git a/arch/arm/include/asm/arch-armada100/config.h b/arch/arm/include/asm/arch-armada100/config.h
new file mode 100644
index 0000000..9995b1a
--- /dev/null
+++ b/arch/arm/include/asm/arch-armada100/config.h
@@ -0,0 +1,50 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+/*
+ * This file should be included in board config header file.
+ *
+ * It supports common definitions for Armada100 platform
+ */
+
+#ifndef _ARMD1_CONFIG_H
+#define _ARMD1_CONFIG_H
+
+#define CONFIG_ARM926EJS	1	/* Basic Architecture */
+
+#define CONFIG_SYS_TCLK		(14745600)	/* NS16550 clk config */
+#define CONFIG_SYS_HZ_CLOCK	(3250000)	/* Timer Freq. 3.25MHZ */
+#define CONFIG_MARVELL_MFP			/* Enable mvmfp driver */
+#define MV_MFPR_BASE		ARMD1_MFPR_BASE
+#define MV_UART_CONSOLE_BASE	ARMD1_UART1_BASE
+#define CONFIG_SYS_NS16550_IER	(1 << 6)	/* Bit 6 in UART_IER register
+						represents UART Unit Enable */
+/*
+ * There is no internal RAM in ARMADA100, using DRAM
+ * TBD: dcache to be used for this
+ */
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_TEXT_BASE - 0x00200000)
+#define CONFIG_NR_DRAM_BANKS_MAX	2
+
+#endif /* _ARMD1_CONFIG_H */
diff --git a/arch/arm/include/asm/arch-kirkwood/config.h b/arch/arm/include/asm/arch-kirkwood/config.h
new file mode 100644
index 0000000..7c6d63b
--- /dev/null
+++ b/arch/arm/include/asm/arch-kirkwood/config.h
@@ -0,0 +1,145 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+/*
+ * This file should be included in board config header file.
+ *
+ * It supports common definitions for Kirkwood platform
+ */
+
+#ifndef _KW_CONFIG_H
+#define _KW_CONFIG_H
+
+#if defined (CONFIG_KW88F6281)
+#include <asm/arch/kw88f6281.h>
+#elif defined (CONFIG_KW88F6192)
+#include <asm/arch/kw88f6192.h>
+#else
+#error "SOC Name not defined"
+#endif /* CONFIG_KW88F6281 */
+
+#define CONFIG_ARM926EJS	1	/* Basic Architecture */
+
+#define CONFIG_MD5	/* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_KIRKWOOD_EGIGA_INIT	/* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8	/* Set RGMII Pad voltage to 1.8V */
+#define CONFIG_KIRKWOOD_PCIE_INIT       /* Enable PCIE Port0 for kernel */
+
+/*
+ * By default kwbimage.cfg from board specific folder is used
+ * If for some board, different configuration file need to be used,
+ * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
+ */
+#ifndef CONFIG_SYS_KWD_CONFIG
+#define	CONFIG_SYS_KWD_CONFIG	$(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage.cfg
+#endif /* CONFIG_SYS_KWD_CONFIG */
+
+/* Kirkwood has 2k of Security SRAM, use it for SP */
+#define CONFIG_SYS_INIT_SP_ADDR		0xC8012000
+#define CONFIG_NR_DRAM_BANKS_MAX	2
+
+#define CONFIG_I2C_MVTWSI_BASE	KW_TWSI_BASE
+#define MV_UART_CONSOLE_BASE	KW_UART0_BASE
+#define MV_SATA_BASE		KW_SATA_BASE
+#define MV_SATA_PORT0_OFFSET	KW_SATA_PORT0_OFFSET
+#define MV_SATA_PORT1_OFFSET	KW_SATA_PORT1_OFFSET
+
+/*
+ * NAND configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_KIRKWOOD
+#define CONFIG_SYS_NAND_BASE		0xD8000000	/* MV_DEFADR_NANDF */
+#define NAND_ALLOW_ERASE_ALL		1
+#endif
+
+/*
+ * SPI Flash configuration
+ */
+#ifdef CONFIG_CMD_SF
+#define CONFIG_HARD_SPI			1
+#define CONFIG_KIRKWOOD_SPI		1
+#define CONFIG_ENV_SPI_BUS		0
+#define CONFIG_ENV_SPI_CS		0
+#define CONFIG_ENV_SPI_MAX_HZ		50000000	/*50Mhz */
+#endif
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_NETCONSOLE	/* include NetConsole support   */
+#define CONFIG_NET_MULTI	/* specify more that one ports available */
+#define CONFIG_MII		/* expose smi ove miiphy interface */
+#define CONFIG_MVGBE		/* Enable Marvell Gbe Controller Driver */
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */
+#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
+#define CONFIG_RESET_PHY_R	/* use reset_phy() to init mv8831116 PHY */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * USB/EHCI
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI_KIRKWOOD
+#define CONFIG_EHCI_IS_TDI
+#endif /* CONFIG_CMD_USB */
+
+/*
+ * IDE Support on SATA ports
+ */
+#ifdef CONFIG_CMD_IDE
+#define __io
+#define CONFIG_CMD_EXT2
+#define CONFIG_MVSATA_IDE
+#define CONFIG_IDE_PREINIT
+#define CONFIG_MVSATA_IDE_USE_PORT1
+/* Needs byte-swapping for ATA data register */
+#define CONFIG_IDE_SWAP_IO
+/* Data, registers and alternate blocks are at the same offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
+/* Each 8-bit ATA register is aligned to a 4-bytes address */
+#define CONFIG_SYS_ATA_STRIDE		4
+/* Controller supports 48-bits LBA addressing */
+#define CONFIG_LBA48
+/* CONFIG_CMD_IDE requires some #defines for ATA registers */
+#define CONFIG_SYS_IDE_MAXBUS		2
+#define CONFIG_SYS_IDE_MAXDEVICE	2
+/* ATA registers base is at SATA controller base */
+#define CONFIG_SYS_ATA_BASE_ADDR	MV_SATA_BASE
+#endif /* CONFIG_CMD_IDE */
+
+/*
+ * I2C related stuff
+ */
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_I2C_MVTWSI
+#define CONFIG_SYS_I2C_SLAVE		0x0
+#define CONFIG_SYS_I2C_SPEED		100000
+#endif
+
+#endif /* _KW_CONFIG_H */
diff --git a/include/configs/aspenite.h b/include/configs/aspenite.h
index 706365f..48706cb 100644
--- a/include/configs/aspenite.h
+++ b/include/configs/aspenite.h
@@ -53,6 +53,7 @@
  * to enable certain macros
  */
 #include "mv-common.h"
+#undef CONFIG_ARCH_MISC_INIT
 
 /*
  * Environment variables configurations
diff --git a/include/configs/mv-common.h b/include/configs/mv-common.h
index 97b6971..a8937dd 100644
--- a/include/configs/mv-common.h
+++ b/include/configs/mv-common.h
@@ -37,54 +37,6 @@
  * High Level Configuration Options (easy to change)
  */
 #define CONFIG_MARVELL		1
-#define CONFIG_ARM926EJS	1	/* Basic Architecture */
-
-/* ====> Kirkwood Platform Common Definations */
-#if defined(CONFIG_KIRKWOOD)
-#define CONFIG_MD5	/* get_random_hex on krikwood needs MD5 support */
-#define CONFIG_KIRKWOOD_EGIGA_INIT	/* Enable GbePort0/1 for kernel */
-#define CONFIG_KIRKWOOD_RGMII_PAD_1V8	/* Set RGMII Pad voltage to 1.8V */
-#define CONFIG_KIRKWOOD_PCIE_INIT       /* Enable PCIE Port0 for kernel */
-
-/*
- * By default kwbimage.cfg from board specific folder is used
- * If for some board, different configuration file need to be used,
- * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
- */
-#ifndef CONFIG_SYS_KWD_CONFIG
-#define	CONFIG_SYS_KWD_CONFIG	$(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage.cfg
-#endif /* CONFIG_SYS_KWD_CONFIG */
-
-/* Kirkwood has 2k of Security SRAM, use it for SP */
-#define CONFIG_SYS_INIT_SP_ADDR		0xC8012000
-#define CONFIG_NR_DRAM_BANKS_MAX	2
-
-#define CONFIG_I2C_MVTWSI_BASE	KW_TWSI_BASE
-#define MV_UART_CONSOLE_BASE	KW_UART0_BASE
-#define MV_SATA_BASE		KW_SATA_BASE
-#define MV_SATA_PORT0_OFFSET	KW_SATA_PORT0_OFFSET
-#define MV_SATA_PORT1_OFFSET	KW_SATA_PORT1_OFFSET
-
-/* ====> ARMADA100 Platform Common Definations */
-#elif defined (CONFIG_ARMADA100)
-
-#define CONFIG_SYS_TCLK		(14745600)	/* NS16550 clk config */
-#define CONFIG_SYS_HZ_CLOCK	(3250000)	/* Timer Freq. 3.25MHZ */
-#define CONFIG_MARVELL_MFP			/* Enable mvmfp driver */
-#define MV_MFPR_BASE		ARMD1_MFPR_BASE
-#define MV_UART_CONSOLE_BASE	ARMD1_UART1_BASE
-#define CONFIG_SYS_NS16550_IER	(1 << 6)	/* Bit 6 in UART_IER register
-						represents UART Unit Enable */
-/*
- * There is no internal RAM in ARMADA100, using DRAM
- * TBD: dcache to be used for this
- */
-#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_TEXT_BASE - 0x00200000)
-#define CONFIG_NR_DRAM_BANKS_MAX	2
-
-#else
-#error "Unsupported SoC Platform..."
-#endif
 
 /*
  * Custom CONFIG_SYS_TEXT_BASE can be done in <board>.h
@@ -138,31 +90,6 @@
 		+sizeof(CONFIG_SYS_PROMPT) + 16)	/* Print Buff */
 
 /*
- * NAND configuration
- */
-#ifdef CONFIG_CMD_NAND
-#define CONFIG_NAND_KIRKWOOD
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define NAND_MAX_CHIPS			1
-#define CONFIG_SYS_NAND_BASE		0xD8000000	/* MV_DEFADR_NANDF */
-#define NAND_ALLOW_ERASE_ALL		1
-#define CONFIG_SYS_64BIT_VSPRINTF	/* needed for nand_util.c */
-#endif
-
-/*
- * SPI Flash configuration
- */
-#ifdef CONFIG_CMD_SF
-#define CONFIG_SPI_FLASH		1
-#define CONFIG_HARD_SPI			1
-#define CONFIG_KIRKWOOD_SPI		1
-#define CONFIG_SPI_FLASH_MACRONIX	1
-#define CONFIG_ENV_SPI_BUS		0
-#define CONFIG_ENV_SPI_CS		0
-#define CONFIG_ENV_SPI_MAX_HZ		50000000	/*50Mhz */
-#endif
-
-/*
  * Size of malloc() pool
  */
 #define CONFIG_SYS_MALLOC_LEN	(1024 * 1024) /* 1MiB for malloc() */
@@ -176,9 +103,7 @@
 #define CONFIG_CMDLINE_EDITING
 #define CONFIG_CONSOLE_INFO_QUIET	/* some code reduction */
 #define CONFIG_ARCH_CPU_INIT	/* call arch_cpu_init() */
-#ifndef CONFIG_ARMADA100	/* will be removed latter */
 #define CONFIG_ARCH_MISC_INIT	/* call arch_misc_init() */
-#endif /* CONFIG_ARMADA100 */
 #define CONFIG_BOARD_EARLY_INIT_F /* call board_init_f for early inits */
 #define CONFIG_DISPLAY_CPUINFO	/* Display cpu info */
 #define CONFIG_STACKSIZE	0x00100000	/* regular stack- 1M */
@@ -199,27 +124,32 @@
 #endif
 #endif /* CONFIG_NR_DRAM_BANKS */
 
+/* ====> Include platform Common Definations */
+#include <asm/arch/config.h>
+
+/* ====> Include driver Common Definations */
 /*
- * Ethernet Driver configuration
+ * Common NAND configuration
  */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_CMD_MII
-#define CONFIG_NETCONSOLE	/* include NetConsole support   */
-#define CONFIG_NET_MULTI	/* specify more that one ports available */
-#define CONFIG_MII		/* expose smi ove miiphy interface */
-#define CONFIG_MVGBE		/* Enable Marvell Gbe Controller Driver */
-#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */
-#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
-#define CONFIG_RESET_PHY_R	/* use reset_phy() to init mv8831116 PHY */
-#endif /* CONFIG_CMD_NET */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_SYS_MAX_NAND_DEVICE     1
+#define NAND_MAX_CHIPS                 1
+#define CONFIG_SYS_64BIT_VSPRINTF      /* needed for nand_util.c */
+#endif
+
+/*
+ * Common SPI Flash configuration
+ */
+#ifdef CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH		1
+#define CONFIG_SPI_FLASH_MACRONIX	1
+#endif
 
 /*
- * USB/EHCI
+ * Common USB/EHCI configuration
  */
 #ifdef CONFIG_CMD_USB
 #define CONFIG_USB_EHCI		/* Enable EHCI USB support */
-#define CONFIG_USB_EHCI_KIRKWOOD
-#define CONFIG_EHCI_IS_TDI
 #define CONFIG_USB_STORAGE
 #define CONFIG_DOS_PARTITION
 #define CONFIG_ISO_PARTITION
@@ -227,44 +157,9 @@
 #endif /* CONFIG_CMD_USB */
 
 /*
- * IDE Support on SATA ports
- */
-#ifdef CONFIG_CMD_IDE
-#define __io
-#define CONFIG_CMD_EXT2
-#define CONFIG_MVSATA_IDE
-#define CONFIG_IDE_PREINIT
-#define CONFIG_MVSATA_IDE_USE_PORT1
-/* Needs byte-swapping for ATA data register */
-#define CONFIG_IDE_SWAP_IO
-/* Data, registers and alternate blocks are at the same offset */
-#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
-#define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
-#define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
-/* Each 8-bit ATA register is aligned to a 4-bytes address */
-#define CONFIG_SYS_ATA_STRIDE		4
-/* Controller supports 48-bits LBA addressing */
-#define CONFIG_LBA48
-/* CONFIG_CMD_IDE requires some #defines for ATA registers */
-#define CONFIG_SYS_IDE_MAXBUS		2
-#define CONFIG_SYS_IDE_MAXDEVICE	2
-/* ATA registers base is at SATA controller base */
-#define CONFIG_SYS_ATA_BASE_ADDR	MV_SATA_BASE
-#endif /* CONFIG_CMD_IDE */
-
-/*
- * I2C related stuff
- */
-#ifdef CONFIG_CMD_I2C
-#define CONFIG_I2C_MVTWSI
-#define CONFIG_SYS_I2C_SLAVE		0x0
-#define CONFIG_SYS_I2C_SPEED		100000
-#endif
-
-/*
  * File system
  */
-#ifndef CONFIG_ARMADA100	/* will be removed latter */
+#ifdef CONFIG_SYS_MVFS
 #define CONFIG_CMD_EXT2
 #define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_FAT
@@ -275,6 +170,6 @@
 #define CONFIG_MTD_PARTITIONS
 #define CONFIG_CMD_MTDPARTS
 #define CONFIG_LZO
-#endif /* CONFIG_ARMADA100 */
+#endif
 
 #endif /* _MV_COMMON_H */
-- 
1.7.0.4

^ permalink raw reply related	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V6 2/5] ARM: Add Support for Marvell Pantheon Familiy SoCs
  2011-01-25  2:40 [U-Boot] [PATCH V6 0/5] Add Pantheon soc and dkb board support Lei Wen
  2011-01-25  2:40 ` [U-Boot] [PATCH V6 1/5] mv: seperate kirkwood and armada from common setting Lei Wen
@ 2011-01-25  2:40 ` Lei Wen
  2011-01-25  2:40 ` [U-Boot] [PATCH V6 3/5] serial: add pantheon soc support Lei Wen
                   ` (8 subsequent siblings)
  10 siblings, 0 replies; 26+ messages in thread
From: Lei Wen @ 2011-01-25  2:40 UTC (permalink / raw)
  To: u-boot

Pantheon Family processors are highly integrated SoCs
based on Sheeva_88SV331x-v5 PJ1 cpu core.
Ref:
http://www.marvell.com/products/processors/communications/marvell_pantheon_910_920_pb.pdf

SoC versions Supported:
1) PANTHEON920          (TD)
2) PANTHEON910          (TTC)

Signed-off-by: Lei Wen <leiwen@marvell.com>
---
V2:

V3:
Fix copyright claim year.

V4:
Add change log to each patch.

V5:
coding style fix.

V6:
Rebase patch on latest u-boot-marvell.git.

 arch/arm/cpu/arm926ejs/pantheon/Makefile      |   46 ++++++
 arch/arm/cpu/arm926ejs/pantheon/cpu.c         |   78 +++++++++
 arch/arm/cpu/arm926ejs/pantheon/dram.c        |  132 ++++++++++++++++
 arch/arm/cpu/arm926ejs/pantheon/timer.c       |  207 +++++++++++++++++++++++++
 arch/arm/include/asm/arch-pantheon/config.h   |   44 ++++++
 arch/arm/include/asm/arch-pantheon/cpu.h      |   79 ++++++++++
 arch/arm/include/asm/arch-pantheon/pantheon.h |   54 +++++++
 7 files changed, 640 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/Makefile
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/cpu.c
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/dram.c
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/timer.c
 create mode 100644 arch/arm/include/asm/arch-pantheon/config.h
 create mode 100644 arch/arm/include/asm/arch-pantheon/cpu.h
 create mode 100644 arch/arm/include/asm/arch-pantheon/pantheon.h

diff --git a/arch/arm/cpu/arm926ejs/pantheon/Makefile b/arch/arm/cpu/arm926ejs/pantheon/Makefile
new file mode 100644
index 0000000..73644c7
--- /dev/null
+++ b/arch/arm/cpu/arm926ejs/pantheon/Makefile
@@ -0,0 +1,46 @@
+#
+# (C) Copyright 2010
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Lei Wen <leiwen@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(SOC).o
+
+COBJS-y	= cpu.o timer.o dram.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS-y))
+
+all:	$(obj).depend $(LIB)
+
+$(LIB):	$(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/arch/arm/cpu/arm926ejs/pantheon/cpu.c b/arch/arm/cpu/arm926ejs/pantheon/cpu.c
new file mode 100644
index 0000000..fd006af
--- /dev/null
+++ b/arch/arm/cpu/arm926ejs/pantheon/cpu.c
@@ -0,0 +1,78 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <asm/arch/pantheon.h>
+#include <asm/io.h>
+
+#define UARTCLK14745KHZ	(APBC_APBCLK | APBC_FNCLK | APBC_FNCLKSEL(1))
+#define SET_MRVL_ID	(1<<8)
+#define L2C_RAM_SEL	(1<<4)
+
+int arch_cpu_init(void)
+{
+	u32 val;
+	struct panthcpu_registers *cpuregs =
+		(struct panthcpu_registers*) PANTHEON_CPU_BASE;
+
+	struct panthapb_registers *apbclkres =
+		(struct panthapb_registers*) PANTHEON_APBC_BASE;
+
+	struct panthmpmu_registers *mpmu =
+		(struct panthmpmu_registers*) PANTHEON_MPMU_BASE;
+
+	/* set SEL_MRVL_ID bit in PANTHEON_CPU_CONF register */
+	val = readl(&cpuregs->cpu_conf);
+	val = val | SET_MRVL_ID;
+	writel(val, &cpuregs->cpu_conf);
+
+	/* Turn on clock gating (PMUM_CCGR) */
+	writel(0xFFFFFFFF, &mpmu->ccgr);
+
+	/* Turn on clock gating (PMUM_ACGR) */
+	writel(0xFFFFFFFF, &mpmu->acgr);
+
+	/* Turn on uart2 clock */
+	writel(UARTCLK14745KHZ, &apbclkres->uart0);
+
+	/* Enable GPIO clock */
+	writel(APBC_APBCLK, &apbclkres->gpio);
+
+	icache_enable();
+
+	return 0;
+}
+
+#if defined(CONFIG_DISPLAY_CPUINFO)
+int print_cpuinfo(void)
+{
+	u32 id;
+	struct panthcpu_registers *cpuregs =
+		(struct panthcpu_registers*) PANTHEON_CPU_BASE;
+
+	id = readl(&cpuregs->chip_id);
+	printf("SoC:   PANTHEON 88AP%X-%X\n", (id & 0xFFF), (id >> 0x10));
+	return 0;
+}
+#endif
diff --git a/arch/arm/cpu/arm926ejs/pantheon/dram.c b/arch/arm/cpu/arm926ejs/pantheon/dram.c
new file mode 100644
index 0000000..2d8709f
--- /dev/null
+++ b/arch/arm/cpu/arm926ejs/pantheon/dram.c
@@ -0,0 +1,132 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>,
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <asm/arch/pantheon.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Pantheon DRAM controller supports upto 8 banks
+ * for chip select 0 and 1
+ */
+
+/*
+ * DDR Memory Control Registers
+ * Refer Datasheet 4.4
+ */
+struct panthddr_map_registers {
+	u32	cs;	/* Memory Address Map Register -CS */
+	u32	pad[3];
+};
+
+struct panthddr_registers {
+	u8	pad[0x100 - 0x000];
+	struct panthddr_map_registers mmap[2];
+};
+
+/*
+ * panth_sdram_base - reads SDRAM Base Address Register
+ */
+u32 panth_sdram_base(int chip_sel)
+{
+	struct panthddr_registers *ddr_regs =
+		(struct panthddr_registers *)PANTHEON_DRAM_BASE;
+	u32 result = 0;
+	u32 CS_valid = 0x01 & readl(&ddr_regs->mmap[chip_sel].cs);
+
+	if (!CS_valid)
+		return 0;
+
+	result = readl(&ddr_regs->mmap[chip_sel].cs) & 0xFF800000;
+	return result;
+}
+
+/*
+ * panth_sdram_size - reads SDRAM size
+ */
+u32 panth_sdram_size(int chip_sel)
+{
+	struct panthddr_registers *ddr_regs =
+		(struct panthddr_registers *)PANTHEON_DRAM_BASE;
+	u32 result = 0;
+	u32 CS_valid = 0x01 & readl(&ddr_regs->mmap[chip_sel].cs);
+
+	if (!CS_valid)
+		return 0;
+
+	result = readl(&ddr_regs->mmap[chip_sel].cs);
+	result = (result >> 16) & 0xF;
+	if (result < 0x7) {
+		printf("Unknown DRAM Size\n");
+		return -1;
+	} else {
+		return ((0x8 << (result - 0x7)) * 1024 * 1024);
+	}
+}
+
+#ifndef CONFIG_SYS_BOARD_DRAM_INIT
+int dram_init(void)
+{
+	int i;
+
+	gd->ram_size = 0;
+	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+		gd->bd->bi_dram[i].start = panth_sdram_base(i);
+		gd->bd->bi_dram[i].size = panth_sdram_size(i);
+		/*
+		 * It is assumed that all memory banks are consecutive
+		 * and without gaps.
+		 * If the gap is found, ram_size will be reported for
+		 * consecutive memory only
+		 */
+		if (gd->bd->bi_dram[i].start != gd->ram_size)
+			break;
+
+		gd->ram_size += gd->bd->bi_dram[i].size;
+
+	}
+
+	for (; i < CONFIG_NR_DRAM_BANKS; i++) {
+		/*
+		 * If above loop terminated prematurely, we need to set
+		 * remaining banks' start address & size as 0. Otherwise other
+		 * u-boot functions and Linux kernel gets wrong values which
+		 * could result in crash
+		 */
+		gd->bd->bi_dram[i].start = 0;
+		gd->bd->bi_dram[i].size = 0;
+	}
+	return 0;
+}
+
+/*
+ * If this function is not defined here,
+ * board.c alters dram bank zero configuration defined above.
+ */
+void dram_init_banksize(void)
+{
+	dram_init();
+}
+#endif /* CONFIG_SYS_BOARD_DRAM_INIT */
diff --git a/arch/arm/cpu/arm926ejs/pantheon/timer.c b/arch/arm/cpu/arm926ejs/pantheon/timer.c
new file mode 100644
index 0000000..5450440
--- /dev/null
+++ b/arch/arm/cpu/arm926ejs/pantheon/timer.c
@@ -0,0 +1,207 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <asm/arch/pantheon.h>
+
+/*
+ * Timer registers
+ * Refer 6.2.9 in Datasheet
+ */
+struct panthtmr_registers {
+	u32 clk_ctrl;	/* Timer clk control reg */
+	u32 match[9];	/* Timer match registers */
+	u32 count[3];	/* Timer count registers */
+	u32 status[3];
+	u32 ie[3];
+	u32 preload[3];	/* Timer preload value */
+	u32 preload_ctrl[3];
+	u32 wdt_match_en;
+	u32 wdt_match_r;
+	u32 wdt_val;
+	u32 wdt_sts;
+	u32 icr[3];
+	u32 wdt_icr;
+	u32 cer;	/* Timer count enable reg */
+	u32 cmr;
+	u32 ilr[3];
+	u32 wcr;
+	u32 wfar;
+	u32 wsar;
+	u32 cvwr[3];
+};
+
+#define TIMER			0	/* Use TIMER 0 */
+/* Each timer has 3 match registers */
+#define MATCH_CMP(x)		((3 * TIMER) + x)
+#define TIMER_LOAD_VAL 		0xffffffff
+#define	COUNT_RD_REQ		0x1
+
+DECLARE_GLOBAL_DATA_PTR;
+/* Using gd->tbu from timestamp and gd->tbl for lastdec */
+
+/*
+ * For preventing risk of instability in reading counter value,
+ * first set read request to register cvwr and then read same
+ * register after it captures counter value.
+ */
+ulong read_timer(void)
+{
+	struct panthtmr_registers *panthtimers =
+		(struct panthtmr_registers *) PANTHEON_TIMER_BASE;
+	volatile int loop=100;
+
+	writel(COUNT_RD_REQ, &panthtimers->cvwr);
+	while (loop--)
+		;
+	return(readl(&panthtimers->cvwr));
+}
+
+void reset_timer_masked(void)
+{
+	/* reset time */
+	gd->tbl = read_timer();
+	gd->tbu = 0;
+}
+
+ulong get_timer_masked(void)
+{
+	ulong now = read_timer();
+
+	if (now >= gd->tbl) {
+		/* normal mode */
+		gd->tbu += now - gd->tbl;
+	} else {
+		/* we have an overflow ... */
+		gd->tbu += now + TIMER_LOAD_VAL - gd->tbl;
+	}
+	gd->tbl = now;
+
+	return gd->tbu;
+}
+
+void reset_timer(void)
+{
+	reset_timer_masked();
+}
+
+ulong get_timer(ulong base)
+{
+	return ((get_timer_masked() / (CONFIG_SYS_HZ_CLOCK / 1000)) -
+		base);
+}
+
+void set_timer(ulong t)
+{
+	gd->tbu = t;
+}
+
+void __udelay(unsigned long usec)
+{
+	ulong delayticks;
+	ulong endtime;
+
+	delayticks = (usec * (CONFIG_SYS_HZ_CLOCK / 1000000));
+	endtime = get_timer_masked() + delayticks;
+
+	while (get_timer_masked() < endtime)
+		;
+}
+
+/*
+ * init the Timer
+ */
+int timer_init(void)
+{
+	struct panthapb_registers *apb1clkres =
+		(struct panthapb_registers *) PANTHEON_APBC_BASE;
+	struct panthtmr_registers *panthtimers =
+		(struct panthtmr_registers *) PANTHEON_TIMER_BASE;
+
+	/* Enable Timer clock@3.25 MHZ */
+	writel(APBC_APBCLK | APBC_FNCLK | APBC_FNCLKSEL(3), &apb1clkres->timers);
+
+	/* load value into timer */
+	writel(0x0, &panthtimers->clk_ctrl);
+	/* Use Timer 0 Match Resiger 0 */
+	writel(TIMER_LOAD_VAL, &panthtimers->match[MATCH_CMP(0)]);
+	/* Preload value is 0 */
+	writel(0x0, &panthtimers->preload[TIMER]);
+	/* Enable match comparator 0 for Timer 0 */
+	writel(0x1, &panthtimers->preload_ctrl[TIMER]);
+
+	/* Enable timer 0 */
+	writel(0x1, &panthtimers->cer);
+	/* init the gd->tbu and gd->tbl value */
+	reset_timer_masked();
+
+	return 0;
+}
+
+#define MPMU_APRR_WDTR	(1<<4)
+#define TMR_WFAR	0xbaba	/* WDT Register First key */
+#define TMP_WSAR	0xeb10	/* WDT Register Second key */
+
+/*
+ * This function uses internal Watchdog Timer
+ * based reset mechanism.
+ * Steps to write watchdog registers (protected access)
+ * 1. Write key value to TMR_WFAR reg.
+ * 2. Write key value to TMP_WSAR reg.
+ * 3. Perform write operation.
+ */
+void reset_cpu (unsigned long ignored)
+{
+	struct panthmpmu_registers *mpmu =
+		(struct panthmpmu_registers *) PANTHEON_MPMU_BASE;
+	struct panthtmr_registers *panthtimers =
+		(struct panthtmr_registers *) PANTHEON_WD_TIMER_BASE;
+	u32 val;
+
+	/* negate hardware reset to the WDT after system reset */
+	val = readl(&mpmu->aprr);
+	val = val | MPMU_APRR_WDTR;
+	writel(val, &mpmu->aprr);
+
+	/* reset/enable WDT clock */
+	writel(APBC_APBCLK, &mpmu->wdtpcr);
+
+	/* clear previous WDT status */
+	writel(TMR_WFAR, &panthtimers->wfar);
+	writel(TMP_WSAR, &panthtimers->wsar);
+	writel(0, &panthtimers->wdt_sts);
+
+	/* set match counter */
+	writel(TMR_WFAR, &panthtimers->wfar);
+	writel(TMP_WSAR, &panthtimers->wsar);
+	writel(0xf, &panthtimers->wdt_match_r);
+
+	/* enable WDT reset */
+	writel(TMR_WFAR, &panthtimers->wfar);
+	writel(TMP_WSAR, &panthtimers->wsar);
+	writel(0x3, &panthtimers->wdt_match_en);
+
+	/*enable functional WDT clock */
+	writel(APBC_APBCLK | APBC_FNCLK, &mpmu->wdtpcr);
+}
diff --git a/arch/arm/include/asm/arch-pantheon/config.h b/arch/arm/include/asm/arch-pantheon/config.h
new file mode 100644
index 0000000..06c9cb8
--- /dev/null
+++ b/arch/arm/include/asm/arch-pantheon/config.h
@@ -0,0 +1,44 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _PANTHEON_CONFIG_H
+#define _PANTHEON_CONFIG_H
+
+#define CONFIG_ARM926EJS	1	/* Basic Architecture */
+
+#define CONFIG_SYS_TCLK		(14745600)	/* NS16550 clk config */
+#define CONFIG_SYS_HZ_CLOCK	(3250000)	/* Timer Freq. 3.25MHZ */
+#define CONFIG_MARVELL_MFP			/* Enable mvmfp driver */
+#define MV_MFPR_BASE		PANTHEON_MFPR_BASE
+#define MV_UART_CONSOLE_BASE	PANTHEON_UART1_BASE
+#define CONFIG_SYS_NS16550_IER	(1 << 6)	/* Bit 6 in UART_IER register
+						represents UART Unit Enable */
+/*
+ * There is no internal RAM in ARMADA100, using DRAM
+ * TBD: dcache to be used for this
+ */
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_TEXT_BASE - 0x00200000)
+#define CONFIG_NR_DRAM_BANKS_MAX	2
+
+#endif /* _PANTHEON_CONFIG_H */
diff --git a/arch/arm/include/asm/arch-pantheon/cpu.h b/arch/arm/include/asm/arch-pantheon/cpu.h
new file mode 100644
index 0000000..1f112c9
--- /dev/null
+++ b/arch/arm/include/asm/arch-pantheon/cpu.h
@@ -0,0 +1,79 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _PANTHEON_CPU_H
+#define _PANTHEON_CPU_H
+
+#include <asm/io.h>
+#include <asm/system.h>
+
+/*
+ * Main Power Management (MPMU) Registers
+ * Refer Register Datasheet 9.1
+ */
+struct panthmpmu_registers {
+	u8 pad0[0x0024];
+	u32 ccgr;	/*0x0024*/
+	u8 pad1[0x0200 - 0x024 - 4];
+	u32 wdtpcr;	/*0x0200*/
+	u8 pad2[0x1020 - 0x200 - 4];
+	u32 aprr;	/*0x1020*/
+	u32 acgr;	/*0x1024*/
+};
+
+/*
+ * APB Clock Reset/Control Registers
+ * Refer Register Datasheet 6.14
+ */
+struct panthapb_registers {
+	u32 uart0;	/*0x000*/
+	u32 uart1;	/*0x004*/
+	u32 gpio;	/*0x008*/
+	u8 pad0[0x034 - 0x08 - 4];
+	u32 timers;	/*0x034*/
+};
+
+/*
+ * CPU Interface Registers
+ * Refer Register Datasheet 4.3
+ */
+struct panthcpu_registers {
+	u32 chip_id;		/* Chip Id Reg */
+	u32 pad;
+	u32 cpu_conf;		/* CPU Conf Reg */
+	u32 pad1;
+	u32 cpu_sram_spd;	/* CPU SRAM Speed Reg */
+	u32 pad2;
+	u32 cpu_l2c_spd;	/* CPU L2cache Speed Conf */
+	u32 mcb_conf;		/* MCB Conf Reg */
+	u32 sys_boot_ctl;	/* Sytem Boot Control */
+};
+
+/*
+ * Functions
+ */
+u32 panth_sdram_base(int);
+u32 panth_sdram_size(int);
+
+#endif /* _PANTHEON_CPU_H */
diff --git a/arch/arm/include/asm/arch-pantheon/pantheon.h b/arch/arm/include/asm/arch-pantheon/pantheon.h
new file mode 100644
index 0000000..fb1b1b5
--- /dev/null
+++ b/arch/arm/include/asm/arch-pantheon/pantheon.h
@@ -0,0 +1,54 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _PANTHEON_H
+#define _PANTHEON_H
+
+#ifndef __ASSEMBLY__
+#include <asm/types.h>
+#include <asm/io.h>
+#endif	/* __ASSEMBLY__ */
+
+#include <asm/arch/cpu.h>
+
+/* Common APB clock register bit definitions */
+#define APBC_APBCLK     (1<<0)  /* APB Bus Clock Enable */
+#define APBC_FNCLK      (1<<1)  /* Functional Clock Enable */
+#define APBC_RST        (1<<2)  /* Reset Generation */
+/* Functional Clock Selection Mask */
+#define APBC_FNCLKSEL(x)        (((x) & 0xf) << 4)
+
+/* Register Base Addresses */
+#define PANTHEON_DRAM_BASE	0xB0000000
+#define PANTHEON_TIMER_BASE	0xD4014000
+#define PANTHEON_WD_TIMER_BASE	0xD4080000
+#define PANTHEON_APBC_BASE	0xD4015000
+#define PANTHEON_UART1_BASE	0xD4017000
+#define PANTHEON_UART2_BASE	0xD4018000
+#define PANTHEON_GPIO_BASE	0xD4019000
+#define PANTHEON_MFPR_BASE	0xD401E000
+#define PANTHEON_MPMU_BASE	0xD4050000
+#define PANTHEON_CPU_BASE	0xD4282C00
+
+#endif /* _PANTHEON_H */
-- 
1.7.0.4

^ permalink raw reply related	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V6 3/5] serial: add pantheon soc support
  2011-01-25  2:40 [U-Boot] [PATCH V6 0/5] Add Pantheon soc and dkb board support Lei Wen
  2011-01-25  2:40 ` [U-Boot] [PATCH V6 1/5] mv: seperate kirkwood and armada from common setting Lei Wen
  2011-01-25  2:40 ` [U-Boot] [PATCH V6 2/5] ARM: Add Support for Marvell Pantheon Familiy SoCs Lei Wen
@ 2011-01-25  2:40 ` Lei Wen
  2011-01-25  2:40 ` [U-Boot] [PATCH V6 4/5] mvmfp: add MFP configuration support for PANTHEON Lei Wen
                   ` (7 subsequent siblings)
  10 siblings, 0 replies; 26+ messages in thread
From: Lei Wen @ 2011-01-25  2:40 UTC (permalink / raw)
  To: u-boot

Signed-off-by: Lei Wen <leiwen@marvell.com>
---
V2:

V3:
Fix copyright claim year.

V4:
Add change log to each patch.

V5:

V6:
Rebase patch on latest u-boot-marvell.git.

drivers/serial/serial.c |    2 ++
 1 files changed, 2 insertions(+), 0 deletions(-)

diff --git a/drivers/serial/serial.c b/drivers/serial/serial.c
index cd3439e..4032dfd 100644
--- a/drivers/serial/serial.c
+++ b/drivers/serial/serial.c
@@ -33,6 +33,8 @@
 #include <asm/arch/orion5x.h>
 #elif defined(CONFIG_ARMADA100)
 #include <asm/arch/armada100.h>
+#elif defined(CONFIG_PANTHEON)
+#include <asm/arch/pantheon.h>
 #endif
 
 #if defined (CONFIG_SERIAL_MULTI)
-- 
1.7.0.4

^ permalink raw reply related	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V6 4/5] mvmfp: add MFP configuration support for PANTHEON
  2011-01-25  2:40 [U-Boot] [PATCH V6 0/5] Add Pantheon soc and dkb board support Lei Wen
                   ` (2 preceding siblings ...)
  2011-01-25  2:40 ` [U-Boot] [PATCH V6 3/5] serial: add pantheon soc support Lei Wen
@ 2011-01-25  2:40 ` Lei Wen
  2011-01-25  2:40 ` [U-Boot] [PATCH V6 5/5] Pantheon: Add Board Support for Marvell dkb board Lei Wen
                   ` (6 subsequent siblings)
  10 siblings, 0 replies; 26+ messages in thread
From: Lei Wen @ 2011-01-25  2:40 UTC (permalink / raw)
  To: u-boot

This patch adds the support MFP support for Marvell PANTHEON SoCs

Signed-off-by: Lei Wen <leiwen@marvell.com>
---
V2:

V3:
Fix copyright claim year.

V4:
Add change log to each patch.

V5:
coding style fix.

V6:
Rebase patch on latest u-boot-marvell.git.

 arch/arm/include/asm/arch-pantheon/mfp.h |   41 ++++++++++++++++++++++++++++++
 drivers/gpio/mvmfp.c                     |    2 +
 2 files changed, 43 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/include/asm/arch-pantheon/mfp.h

diff --git a/arch/arm/include/asm/arch-pantheon/mfp.h b/arch/arm/include/asm/arch-pantheon/mfp.h
new file mode 100644
index 0000000..ce3aca1
--- /dev/null
+++ b/arch/arm/include/asm/arch-pantheon/mfp.h
@@ -0,0 +1,41 @@
+/*
+ * Based on arch/arm/include/asm/arch-armada100/mfp.h
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __PANTHEON_MFP_H
+#define __PANTHEON_MFP_H
+
+/*
+ * Frequently used MFP Configuration macros for all PANTHEON family of SoCs
+ *
+ * offset, pull,pF, drv,dF, edge,eF ,afn,aF
+ */
+/* UART2 */
+#define MFP47_UART2_RXD		MFP_REG(0x198) | MFP_AF6 | MFP_DRIVE_MEDIUM
+#define MFP48_UART2_TXD		MFP_REG(0x19c) | MFP_AF6 | MFP_DRIVE_MEDIUM
+
+/* More macros can be defined here... */
+
+#define MFP_PIN_MAX	117
+#endif
diff --git a/drivers/gpio/mvmfp.c b/drivers/gpio/mvmfp.c
index 5646ed4..e7830c6 100644
--- a/drivers/gpio/mvmfp.c
+++ b/drivers/gpio/mvmfp.c
@@ -28,6 +28,8 @@
 #include <asm/arch/mfp.h>
 #ifdef CONFIG_ARMADA100
 #include <asm/arch/armada100.h>
+#elif defined(CONFIG_PANTHEON)
+#include <asm/arch/pantheon.h>
 #else
 #error Unsupported SoC...
 #endif
-- 
1.7.0.4

^ permalink raw reply related	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V6 5/5] Pantheon: Add Board Support for Marvell dkb board
  2011-01-25  2:40 [U-Boot] [PATCH V6 0/5] Add Pantheon soc and dkb board support Lei Wen
                   ` (3 preceding siblings ...)
  2011-01-25  2:40 ` [U-Boot] [PATCH V6 4/5] mvmfp: add MFP configuration support for PANTHEON Lei Wen
@ 2011-01-25  2:40 ` Lei Wen
  2011-01-26 10:31 ` [U-Boot] [PATCH V7 0/5] Add Pantheon soc and dkb board support Lei Wen
                   ` (5 subsequent siblings)
  10 siblings, 0 replies; 26+ messages in thread
From: Lei Wen @ 2011-01-25  2:40 UTC (permalink / raw)
  To: u-boot

DKB is a Development Board for PANTHEON TD/TTC(pxa920/pxa910) with
* Processor upto 806Mhz
* LPDDR1/2
* x8/x16 SLC/MLC NAND
* Footprints for eMMC & MMC x8 card

With Peripherals:
* Parallel LCD I/F
* Audio codecs (88PM8607)
* MIPI CSI-2 camera
* Marvell 88W8787 802.11n/BT module
* Marvell 2G/3G RF
* Dual analog mics & speakers, headset jack, LED, ambient
* USB2.0 HS host, OTG (mini AB)
* GPIO, GPIO expander with DIP switches for easier selection
* UART serial over USB, CIR

This patch adds basic board support with DRAM and UART functionality

Signed-off-by: Lei Wen <leiwen@marvell.com>
---
V2:

V3:
Fix copyright claim year.

V4:
Add change log to each patch.

V5:
Remove additional CONFIG_SYS_NS16550_COM1 definition in dkb.h

V6:
Rebase patch on latest u-boot-marvell.git.
And fix a build warning.

 MAINTAINERS                |    4 +++
 board/Marvell/dkb/Makefile |   51 ++++++++++++++++++++++++++++++++++++
 board/Marvell/dkb/dkb.c    |   54 ++++++++++++++++++++++++++++++++++++++
 boards.cfg                 |    1 +
 include/configs/dkb.h      |   62 ++++++++++++++++++++++++++++++++++++++++++++
 5 files changed, 172 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/dkb/Makefile
 create mode 100644 board/Marvell/dkb/dkb.c
 create mode 100644 include/configs/dkb.h

diff --git a/MAINTAINERS b/MAINTAINERS
index d92ff8d..36e2516 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -850,6 +850,10 @@ Prafulla Wadaskar <prafulla@marvell.com>
 	rd6281a		ARM926EJS (Kirkwood SoC)
 	sheevaplug	ARM926EJS (Kirkwood SoC)
 
+Lei Wen <leiwen@marvell.com>
+
+	dkb		ARM926EJS (PANTHEON 88AP920 SOC)
+
 Matthias Weisser <weisserm@arcor.de>
 
 	jadecpu		ARM926EJS (MB86R01 SoC)
diff --git a/board/Marvell/dkb/Makefile b/board/Marvell/dkb/Makefile
new file mode 100644
index 0000000..8835f8e
--- /dev/null
+++ b/board/Marvell/dkb/Makefile
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2010
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Lei Wen <leiwen@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB     = $(obj)lib$(BOARD).o
+
+COBJS	:= dkb.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/Marvell/dkb/dkb.c b/board/Marvell/dkb/dkb.c
new file mode 100644
index 0000000..95a3982
--- /dev/null
+++ b/board/Marvell/dkb/dkb.c
@@ -0,0 +1,54 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <mvmfp.h>
+#include <asm/arch/mfp.h>
+#include <asm/arch/cpu.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+	u32 mfp_cfg[] = {
+		/* Enable Console on UART2 */
+		MFP47_UART2_RXD,
+		MFP48_UART2_TXD,
+
+		MFP_EOC		/*End of configureation*/
+	};
+	/* configure MFP's */
+	mfp_config(mfp_cfg);
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* arch number of Board */
+	gd->bd->bi_arch_number = MACH_TYPE_TTC_DKB;
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = panth_sdram_base(0) + 0x100;
+	return 0;
+}
diff --git a/boards.cfg b/boards.cfg
index 350f287..7e1e283 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -104,6 +104,7 @@ imx27lite                    arm         arm926ejs   imx27lite           logicpd
 magnesium                    arm         arm926ejs   imx27lite           logicpd        mx27
 omap5912osk                  arm         arm926ejs   -                   ti             omap
 edminiv2                     arm         arm926ejs   -                   LaCie          orion5x
+dkb			     arm         arm926ejs   -                   Marvell        pantheon
 ca9x4_ct_vxp                 arm         armv7       vexpress            armltd
 mx51evk                      arm         armv7       mx51evk             freescale      mx5
 mx53evk                      arm         armv7       mx53evk             freescale      mx5
diff --git a/include/configs/dkb.h b/include/configs/dkb.h
new file mode 100644
index 0000000..089805e
--- /dev/null
+++ b/include/configs/dkb.h
@@ -0,0 +1,62 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __CONFIG_DKB_H
+#define __CONFIG_DKB_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING	"\nMarvell-TTC DKB"
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_SHEEVA_88SV331xV5	1	/* CPU Core subversion */
+#define CONFIG_PANTHEON			1	/* SOC Family Name */
+#define CONFIG_MACH_TTC_DKB		1	/* Machine type */
+#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH		/* Declare no flash (NOR/SPI) */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_AUTOSCRIPT
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+#undef CONFIG_ARCH_MISC_INIT
+/*
+ * Environment variables configurations
+ */
+#define CONFIG_ENV_IS_NOWHERE	1	/* if env in SDRAM */
+#define CONFIG_ENV_SIZE	0x20000	/* 64k */
+
+#endif	/* __CONFIG_DKB_H */
-- 
1.7.0.4

^ permalink raw reply related	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V7 0/5] Add Pantheon soc and dkb board support
  2011-01-25  2:40 [U-Boot] [PATCH V6 0/5] Add Pantheon soc and dkb board support Lei Wen
                   ` (4 preceding siblings ...)
  2011-01-25  2:40 ` [U-Boot] [PATCH V6 5/5] Pantheon: Add Board Support for Marvell dkb board Lei Wen
@ 2011-01-26 10:31 ` Lei Wen
  2011-01-28  9:19   ` [U-Boot] [PATCH V8 " Lei Wen
                     ` (5 more replies)
  2011-01-26 10:31 ` [U-Boot] [PATCH V7 1/5] mv: seperate kirkwood and armada from common setting Lei Wen
                   ` (4 subsequent siblings)
  10 siblings, 6 replies; 26+ messages in thread
From: Lei Wen @ 2011-01-26 10:31 UTC (permalink / raw)
  To: u-boot

This patch set add the Pantheon soc and dkb board support.

V2:
This patch seris update the seperate mv_common part as suggested.

V3:
Fix config.h include place and copyright claim year.

V4:
Add change log to each patch.

V5:
Add doc in Readme for new CONFIG_SYS_MVFS.
code style fix.

V6:
Rebase patch on latest u-boot-marvell.git.
And fix a build warning.

V7:
Fix CONFIG_SYS_INIT_SP_ADDR put place.
Fix timer read to avoid potential optimization out of loop.
Correct comments in the fourth patch.

Lei Wen (5):
  mv: seperate kirkwood and armada from common setting
  ARM: Add Support for Marvell Pantheon Familiy SoCs
  serial: add pantheon soc support
  mvmfp: add MFP configuration support for PANTHEON
  Pantheon: Add Board Support for Marvell dkb board

 MAINTAINERS                                   |    4 +
 README                                        |    5 +
 arch/arm/cpu/arm926ejs/pantheon/Makefile      |   46 ++++++
 arch/arm/cpu/arm926ejs/pantheon/cpu.c         |   78 +++++++++
 arch/arm/cpu/arm926ejs/pantheon/dram.c        |  132 +++++++++++++++
 arch/arm/cpu/arm926ejs/pantheon/timer.c       |  214 +++++++++++++++++++++++++
 arch/arm/include/asm/arch-armada100/config.h  |   44 +++++
 arch/arm/include/asm/arch-kirkwood/config.h   |  145 +++++++++++++++++
 arch/arm/include/asm/arch-pantheon/config.h   |   38 +++++
 arch/arm/include/asm/arch-pantheon/cpu.h      |   79 +++++++++
 arch/arm/include/asm/arch-pantheon/mfp.h      |   41 +++++
 arch/arm/include/asm/arch-pantheon/pantheon.h |   54 ++++++
 board/Marvell/dkb/Makefile                    |   51 ++++++
 board/Marvell/dkb/dkb.c                       |   54 ++++++
 boards.cfg                                    |    1 +
 drivers/gpio/mvmfp.c                          |    2 +
 drivers/serial/serial.c                       |    2 +
 include/configs/aspenite.h                    |    8 +
 include/configs/dkb.h                         |   65 ++++++++
 include/configs/mv-common.h                   |  147 +++---------------
 20 files changed, 1084 insertions(+), 126 deletions(-)
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/Makefile
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/cpu.c
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/dram.c
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/timer.c
 create mode 100644 arch/arm/include/asm/arch-armada100/config.h
 create mode 100644 arch/arm/include/asm/arch-kirkwood/config.h
 create mode 100644 arch/arm/include/asm/arch-pantheon/config.h
 create mode 100644 arch/arm/include/asm/arch-pantheon/cpu.h
 create mode 100644 arch/arm/include/asm/arch-pantheon/mfp.h
 create mode 100644 arch/arm/include/asm/arch-pantheon/pantheon.h
 create mode 100644 board/Marvell/dkb/Makefile
 create mode 100644 board/Marvell/dkb/dkb.c
 create mode 100644 include/configs/dkb.h

^ permalink raw reply	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V8 0/5] Add Pantheon soc and dkb board support
  2011-01-26 10:31 ` [U-Boot] [PATCH V7 0/5] Add Pantheon soc and dkb board support Lei Wen
@ 2011-01-28  9:19   ` Lei Wen
  2011-02-05  6:53     ` Albert ARIBAUD
  2011-02-09  9:47     ` Prafulla Wadaskar
  2011-01-28  9:19   ` [U-Boot] [PATCH V8 1/5] mv: seperate kirkwood and armada from common setting Lei Wen
                     ` (4 subsequent siblings)
  5 siblings, 2 replies; 26+ messages in thread
From: Lei Wen @ 2011-01-28  9:19 UTC (permalink / raw)
  To: u-boot

This patch set add the Pantheon soc and dkb board support.

V2:
This patch seris update the seperate mv_common part as suggested.

V3:
Fix config.h include place and copyright claim year.

V4:
Add change log to each patch.

V5:
Add doc in Readme for new CONFIG_SYS_MVFS.
code style fix.

V6:
Rebase patch on latest u-boot-marvell.git.
And fix a build warning.

V7:
Fix CONFIG_SYS_INIT_SP_ADDR put place.
Fix timer read to avoid potential optimization out of loop.
Correct comments in the fourth patch.

V8:
Fix copyright claim year.

Lei Wen (5):
  mv: seperate kirkwood and armada from common setting
  ARM: Add Support for Marvell Pantheon Familiy SoCs
  serial: add pantheon soc support
  mvmfp: add MFP configuration support for PANTHEON
  Pantheon: Add Board Support for Marvell dkb board

 MAINTAINERS                                   |    4 +
 README                                        |    5 +
 arch/arm/cpu/arm926ejs/pantheon/Makefile      |   46 ++++++
 arch/arm/cpu/arm926ejs/pantheon/cpu.c         |   78 +++++++++
 arch/arm/cpu/arm926ejs/pantheon/dram.c        |  132 +++++++++++++++
 arch/arm/cpu/arm926ejs/pantheon/timer.c       |  214 +++++++++++++++++++++++++
 arch/arm/include/asm/arch-armada100/config.h  |   44 +++++
 arch/arm/include/asm/arch-kirkwood/config.h   |  145 +++++++++++++++++
 arch/arm/include/asm/arch-pantheon/config.h   |   38 +++++
 arch/arm/include/asm/arch-pantheon/cpu.h      |   79 +++++++++
 arch/arm/include/asm/arch-pantheon/mfp.h      |   41 +++++
 arch/arm/include/asm/arch-pantheon/pantheon.h |   54 ++++++
 board/Marvell/dkb/Makefile                    |   51 ++++++
 board/Marvell/dkb/dkb.c                       |   54 ++++++
 boards.cfg                                    |    1 +
 drivers/gpio/mvmfp.c                          |    2 +
 drivers/serial/serial.c                       |    2 +
 include/configs/aspenite.h                    |    8 +
 include/configs/dkb.h                         |   65 ++++++++
 include/configs/mv-common.h                   |  147 +++---------------
 20 files changed, 1084 insertions(+), 126 deletions(-)
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/Makefile
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/cpu.c
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/dram.c
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/timer.c
 create mode 100644 arch/arm/include/asm/arch-armada100/config.h
 create mode 100644 arch/arm/include/asm/arch-kirkwood/config.h
 create mode 100644 arch/arm/include/asm/arch-pantheon/config.h
 create mode 100644 arch/arm/include/asm/arch-pantheon/cpu.h
 create mode 100644 arch/arm/include/asm/arch-pantheon/mfp.h
 create mode 100644 arch/arm/include/asm/arch-pantheon/pantheon.h
 create mode 100644 board/Marvell/dkb/Makefile
 create mode 100644 board/Marvell/dkb/dkb.c
 create mode 100644 include/configs/dkb.h

^ permalink raw reply	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V8 0/5] Add Pantheon soc and dkb board support
  2011-01-28  9:19   ` [U-Boot] [PATCH V8 " Lei Wen
@ 2011-02-05  6:53     ` Albert ARIBAUD
  2011-02-09  9:47     ` Prafulla Wadaskar
  1 sibling, 0 replies; 26+ messages in thread
From: Albert ARIBAUD @ 2011-02-05  6:53 UTC (permalink / raw)
  To: u-boot

Hi All,

Le 28/01/2011 10:19, Lei Wen a ?crit :
> This patch set add the Pantheon soc and dkb board support.

Prafulla,

Is this patchset going to go into u-boot-marvell and requested for pull 
before 2011-03 is out?

Amicalement,
-- 
Albert.

^ permalink raw reply	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V8 0/5] Add Pantheon soc and dkb board support
  2011-01-28  9:19   ` [U-Boot] [PATCH V8 " Lei Wen
  2011-02-05  6:53     ` Albert ARIBAUD
@ 2011-02-09  9:47     ` Prafulla Wadaskar
  1 sibling, 0 replies; 26+ messages in thread
From: Prafulla Wadaskar @ 2011-02-09  9:47 UTC (permalink / raw)
  To: u-boot



> -----Original Message-----
> From: Lei Wen [mailto:leiwen at marvell.com]
> Sent: Friday, January 28, 2011 1:19 AM
> To: Albert ARIBAUD; Wolfgang Denk; u-boot at lists.denx.de; Prafulla
> Wadaskar; Yu Tang; Ashish Karkare; Prabhanjan Sarnaik; Lei Wen
> Subject: [PATCH V8 0/5] Add Pantheon soc and dkb board support
> 
> This patch set add the Pantheon soc and dkb board support.
> 
> V2:
> This patch seris update the seperate mv_common part as suggested.
> 
> V3:
> Fix config.h include place and copyright claim year.
> 
> V4:
> Add change log to each patch.
> 
> V5:
> Add doc in Readme for new CONFIG_SYS_MVFS.
> code style fix.
> 
> V6:
> Rebase patch on latest u-boot-marvell.git.
> And fix a build warning.
> 
> V7:
> Fix CONFIG_SYS_INIT_SP_ADDR put place.
> Fix timer read to avoid potential optimization out of loop.
> Correct comments in the fourth patch.
> 
> V8:
> Fix copyright claim year.
> 
> Lei Wen (5):
>   mv: seperate kirkwood and armada from common setting
>   ARM: Add Support for Marvell Pantheon Familiy SoCs
>   serial: add pantheon soc support
>   mvmfp: add MFP configuration support for PANTHEON
>   Pantheon: Add Board Support for Marvell dkb board
> 
>  MAINTAINERS                                   |    4 +
>  README                                        |    5 +
>  arch/arm/cpu/arm926ejs/pantheon/Makefile      |   46 ++++++
>  arch/arm/cpu/arm926ejs/pantheon/cpu.c         |   78 +++++++++
>  arch/arm/cpu/arm926ejs/pantheon/dram.c        |  132 +++++++++++++++
>  arch/arm/cpu/arm926ejs/pantheon/timer.c       |  214
> +++++++++++++++++++++++++
>  arch/arm/include/asm/arch-armada100/config.h  |   44 +++++
>  arch/arm/include/asm/arch-kirkwood/config.h   |  145 +++++++++++++++++
>  arch/arm/include/asm/arch-pantheon/config.h   |   38 +++++
>  arch/arm/include/asm/arch-pantheon/cpu.h      |   79 +++++++++
>  arch/arm/include/asm/arch-pantheon/mfp.h      |   41 +++++
>  arch/arm/include/asm/arch-pantheon/pantheon.h |   54 ++++++
>  board/Marvell/dkb/Makefile                    |   51 ++++++
>  board/Marvell/dkb/dkb.c                       |   54 ++++++
>  boards.cfg                                    |    1 +
>  drivers/gpio/mvmfp.c                          |    2 +
>  drivers/serial/serial.c                       |    2 +
>  include/configs/aspenite.h                    |    8 +
>  include/configs/dkb.h                         |   65 ++++++++
>  include/configs/mv-common.h                   |  147 +++---------------
>  20 files changed, 1084 insertions(+), 126 deletions(-)
>  create mode 100644 arch/arm/cpu/arm926ejs/pantheon/Makefile
>  create mode 100644 arch/arm/cpu/arm926ejs/pantheon/cpu.c
>  create mode 100644 arch/arm/cpu/arm926ejs/pantheon/dram.c
>  create mode 100644 arch/arm/cpu/arm926ejs/pantheon/timer.c
>  create mode 100644 arch/arm/include/asm/arch-armada100/config.h
>  create mode 100644 arch/arm/include/asm/arch-kirkwood/config.h
>  create mode 100644 arch/arm/include/asm/arch-pantheon/config.h
>  create mode 100644 arch/arm/include/asm/arch-pantheon/cpu.h
>  create mode 100644 arch/arm/include/asm/arch-pantheon/mfp.h
>  create mode 100644 arch/arm/include/asm/arch-pantheon/pantheon.h
>  create mode 100644 board/Marvell/dkb/Makefile
>  create mode 100644 board/Marvell/dkb/dkb.c
>  create mode 100644 include/configs/dkb.h

Applied this patch series to u-boot-marvell.git next branch

Regards..
Prafulla . .

^ permalink raw reply	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V8 1/5] mv: seperate kirkwood and armada from common setting
  2011-01-26 10:31 ` [U-Boot] [PATCH V7 0/5] Add Pantheon soc and dkb board support Lei Wen
  2011-01-28  9:19   ` [U-Boot] [PATCH V8 " Lei Wen
@ 2011-01-28  9:19   ` Lei Wen
  2011-01-28  9:19   ` [U-Boot] [PATCH V8 2/5] ARM: Add Support for Marvell Pantheon Familiy SoCs Lei Wen
                     ` (3 subsequent siblings)
  5 siblings, 0 replies; 26+ messages in thread
From: Lei Wen @ 2011-01-28  9:19 UTC (permalink / raw)
  To: u-boot

Since there are lots of difference between kirkwood and armada series,
it is better to seperate them but still keep the most common file
shared by all marvell platform in the mv-common configure file.

This patch move the kirkwood only driver definitoin in mv-common to
the <soc_name>/config.h.

This patch is tested with compilation for armada100 and guruplug.

Signed-off-by: Lei Wen <leiwen@marvell.com>
---
V2:
This patch seris update the seperate mv_common part as suggested.

V3:
Fix config.h include place and copyright claim year.

V4:
Add change log to each patch.

V5:
Add CONFIG_SYS_MVFS doc in README.

V6:
Rebase patch on latest u-boot-marvell.git.

V7:
Fix CONFIG_SYS_INIT_SP_ADDR put place.

V8:
Fix copyright claim year.

 README                                       |    5 +
 arch/arm/include/asm/arch-armada100/config.h |   44 ++++++++
 arch/arm/include/asm/arch-kirkwood/config.h  |  145 +++++++++++++++++++++++++
 include/configs/aspenite.h                   |    8 ++
 include/configs/mv-common.h                  |  147 ++++----------------------
 5 files changed, 223 insertions(+), 126 deletions(-)
 create mode 100644 arch/arm/include/asm/arch-armada100/config.h
 create mode 100644 arch/arm/include/asm/arch-kirkwood/config.h

diff --git a/README b/README
index 755d17c..7c0d480 100644
--- a/README
+++ b/README
@@ -319,6 +319,11 @@ The following options need to be configured:
 			CONFIG_SYS_PQ2FADS	- PQ2FADS-ZU or PQ2FADS-VR
 			CONFIG_SYS_8272ADS	- MPC8272ADS
 
+- Marvell Family Member
+		CONFIG_SYS_MVFS		- define it if you want to enable
+					  multiple fs option at one time
+					  for marvell soc family
+
 - MPC824X Family Member (if CONFIG_MPC824X is defined)
 		Define exactly one of
 		CONFIG_MPC8240, CONFIG_MPC8245
diff --git a/arch/arm/include/asm/arch-armada100/config.h b/arch/arm/include/asm/arch-armada100/config.h
new file mode 100644
index 0000000..d804002
--- /dev/null
+++ b/arch/arm/include/asm/arch-armada100/config.h
@@ -0,0 +1,44 @@
+/*
+ * (C) Copyright 2011
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+/*
+ * This file should be included in board config header file.
+ *
+ * It supports common definitions for Armada100 platform
+ */
+
+#ifndef _ARMD1_CONFIG_H
+#define _ARMD1_CONFIG_H
+
+#define CONFIG_ARM926EJS	1	/* Basic Architecture */
+
+#define CONFIG_SYS_TCLK		(14745600)	/* NS16550 clk config */
+#define CONFIG_SYS_HZ_CLOCK	(3250000)	/* Timer Freq. 3.25MHZ */
+#define CONFIG_MARVELL_MFP			/* Enable mvmfp driver */
+#define MV_MFPR_BASE		ARMD1_MFPR_BASE
+#define MV_UART_CONSOLE_BASE	ARMD1_UART1_BASE
+#define CONFIG_SYS_NS16550_IER	(1 << 6)	/* Bit 6 in UART_IER register
+						represents UART Unit Enable */
+
+#endif /* _ARMD1_CONFIG_H */
diff --git a/arch/arm/include/asm/arch-kirkwood/config.h b/arch/arm/include/asm/arch-kirkwood/config.h
new file mode 100644
index 0000000..71ba464
--- /dev/null
+++ b/arch/arm/include/asm/arch-kirkwood/config.h
@@ -0,0 +1,145 @@
+/*
+ * (C) Copyright 2011
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+/*
+ * This file should be included in board config header file.
+ *
+ * It supports common definitions for Kirkwood platform
+ */
+
+#ifndef _KW_CONFIG_H
+#define _KW_CONFIG_H
+
+#if defined (CONFIG_KW88F6281)
+#include <asm/arch/kw88f6281.h>
+#elif defined (CONFIG_KW88F6192)
+#include <asm/arch/kw88f6192.h>
+#else
+#error "SOC Name not defined"
+#endif /* CONFIG_KW88F6281 */
+
+#define CONFIG_ARM926EJS	1	/* Basic Architecture */
+
+#define CONFIG_MD5	/* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_KIRKWOOD_EGIGA_INIT	/* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8	/* Set RGMII Pad voltage to 1.8V */
+#define CONFIG_KIRKWOOD_PCIE_INIT       /* Enable PCIE Port0 for kernel */
+
+/*
+ * By default kwbimage.cfg from board specific folder is used
+ * If for some board, different configuration file need to be used,
+ * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
+ */
+#ifndef CONFIG_SYS_KWD_CONFIG
+#define	CONFIG_SYS_KWD_CONFIG	$(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage.cfg
+#endif /* CONFIG_SYS_KWD_CONFIG */
+
+/* Kirkwood has 2k of Security SRAM, use it for SP */
+#define CONFIG_SYS_INIT_SP_ADDR		0xC8012000
+#define CONFIG_NR_DRAM_BANKS_MAX	2
+
+#define CONFIG_I2C_MVTWSI_BASE	KW_TWSI_BASE
+#define MV_UART_CONSOLE_BASE	KW_UART0_BASE
+#define MV_SATA_BASE		KW_SATA_BASE
+#define MV_SATA_PORT0_OFFSET	KW_SATA_PORT0_OFFSET
+#define MV_SATA_PORT1_OFFSET	KW_SATA_PORT1_OFFSET
+
+/*
+ * NAND configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_KIRKWOOD
+#define CONFIG_SYS_NAND_BASE		0xD8000000	/* MV_DEFADR_NANDF */
+#define NAND_ALLOW_ERASE_ALL		1
+#endif
+
+/*
+ * SPI Flash configuration
+ */
+#ifdef CONFIG_CMD_SF
+#define CONFIG_HARD_SPI			1
+#define CONFIG_KIRKWOOD_SPI		1
+#define CONFIG_ENV_SPI_BUS		0
+#define CONFIG_ENV_SPI_CS		0
+#define CONFIG_ENV_SPI_MAX_HZ		50000000	/*50Mhz */
+#endif
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_NETCONSOLE	/* include NetConsole support   */
+#define CONFIG_NET_MULTI	/* specify more that one ports available */
+#define CONFIG_MII		/* expose smi ove miiphy interface */
+#define CONFIG_MVGBE		/* Enable Marvell Gbe Controller Driver */
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */
+#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
+#define CONFIG_RESET_PHY_R	/* use reset_phy() to init mv8831116 PHY */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * USB/EHCI
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI_KIRKWOOD
+#define CONFIG_EHCI_IS_TDI
+#endif /* CONFIG_CMD_USB */
+
+/*
+ * IDE Support on SATA ports
+ */
+#ifdef CONFIG_CMD_IDE
+#define __io
+#define CONFIG_CMD_EXT2
+#define CONFIG_MVSATA_IDE
+#define CONFIG_IDE_PREINIT
+#define CONFIG_MVSATA_IDE_USE_PORT1
+/* Needs byte-swapping for ATA data register */
+#define CONFIG_IDE_SWAP_IO
+/* Data, registers and alternate blocks are at the same offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
+/* Each 8-bit ATA register is aligned to a 4-bytes address */
+#define CONFIG_SYS_ATA_STRIDE		4
+/* Controller supports 48-bits LBA addressing */
+#define CONFIG_LBA48
+/* CONFIG_CMD_IDE requires some #defines for ATA registers */
+#define CONFIG_SYS_IDE_MAXBUS		2
+#define CONFIG_SYS_IDE_MAXDEVICE	2
+/* ATA registers base is at SATA controller base */
+#define CONFIG_SYS_ATA_BASE_ADDR	MV_SATA_BASE
+#endif /* CONFIG_CMD_IDE */
+
+/*
+ * I2C related stuff
+ */
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_I2C_MVTWSI
+#define CONFIG_SYS_I2C_SLAVE		0x0
+#define CONFIG_SYS_I2C_SPEED		100000
+#endif
+
+#endif /* _KW_CONFIG_H */
diff --git a/include/configs/aspenite.h b/include/configs/aspenite.h
index 706365f..fd35f3e 100644
--- a/include/configs/aspenite.h
+++ b/include/configs/aspenite.h
@@ -41,6 +41,13 @@
 #define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
 
 /*
+ * There is no internal RAM in ARMADA100, using DRAM
+ * TBD: dcache to be used for this
+ */
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_TEXT_BASE - 0x00200000)
+#define CONFIG_NR_DRAM_BANKS_MAX	2
+
+/*
  * Commands configuration
  */
 #define CONFIG_SYS_NO_FLASH		/* Declare no flash (NOR/SPI) */
@@ -53,6 +60,7 @@
  * to enable certain macros
  */
 #include "mv-common.h"
+#undef CONFIG_ARCH_MISC_INIT
 
 /*
  * Environment variables configurations
diff --git a/include/configs/mv-common.h b/include/configs/mv-common.h
index 97b6971..a8937dd 100644
--- a/include/configs/mv-common.h
+++ b/include/configs/mv-common.h
@@ -37,54 +37,6 @@
  * High Level Configuration Options (easy to change)
  */
 #define CONFIG_MARVELL		1
-#define CONFIG_ARM926EJS	1	/* Basic Architecture */
-
-/* ====> Kirkwood Platform Common Definations */
-#if defined(CONFIG_KIRKWOOD)
-#define CONFIG_MD5	/* get_random_hex on krikwood needs MD5 support */
-#define CONFIG_KIRKWOOD_EGIGA_INIT	/* Enable GbePort0/1 for kernel */
-#define CONFIG_KIRKWOOD_RGMII_PAD_1V8	/* Set RGMII Pad voltage to 1.8V */
-#define CONFIG_KIRKWOOD_PCIE_INIT       /* Enable PCIE Port0 for kernel */
-
-/*
- * By default kwbimage.cfg from board specific folder is used
- * If for some board, different configuration file need to be used,
- * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
- */
-#ifndef CONFIG_SYS_KWD_CONFIG
-#define	CONFIG_SYS_KWD_CONFIG	$(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage.cfg
-#endif /* CONFIG_SYS_KWD_CONFIG */
-
-/* Kirkwood has 2k of Security SRAM, use it for SP */
-#define CONFIG_SYS_INIT_SP_ADDR		0xC8012000
-#define CONFIG_NR_DRAM_BANKS_MAX	2
-
-#define CONFIG_I2C_MVTWSI_BASE	KW_TWSI_BASE
-#define MV_UART_CONSOLE_BASE	KW_UART0_BASE
-#define MV_SATA_BASE		KW_SATA_BASE
-#define MV_SATA_PORT0_OFFSET	KW_SATA_PORT0_OFFSET
-#define MV_SATA_PORT1_OFFSET	KW_SATA_PORT1_OFFSET
-
-/* ====> ARMADA100 Platform Common Definations */
-#elif defined (CONFIG_ARMADA100)
-
-#define CONFIG_SYS_TCLK		(14745600)	/* NS16550 clk config */
-#define CONFIG_SYS_HZ_CLOCK	(3250000)	/* Timer Freq. 3.25MHZ */
-#define CONFIG_MARVELL_MFP			/* Enable mvmfp driver */
-#define MV_MFPR_BASE		ARMD1_MFPR_BASE
-#define MV_UART_CONSOLE_BASE	ARMD1_UART1_BASE
-#define CONFIG_SYS_NS16550_IER	(1 << 6)	/* Bit 6 in UART_IER register
-						represents UART Unit Enable */
-/*
- * There is no internal RAM in ARMADA100, using DRAM
- * TBD: dcache to be used for this
- */
-#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_TEXT_BASE - 0x00200000)
-#define CONFIG_NR_DRAM_BANKS_MAX	2
-
-#else
-#error "Unsupported SoC Platform..."
-#endif
 
 /*
  * Custom CONFIG_SYS_TEXT_BASE can be done in <board>.h
@@ -138,31 +90,6 @@
 		+sizeof(CONFIG_SYS_PROMPT) + 16)	/* Print Buff */
 
 /*
- * NAND configuration
- */
-#ifdef CONFIG_CMD_NAND
-#define CONFIG_NAND_KIRKWOOD
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define NAND_MAX_CHIPS			1
-#define CONFIG_SYS_NAND_BASE		0xD8000000	/* MV_DEFADR_NANDF */
-#define NAND_ALLOW_ERASE_ALL		1
-#define CONFIG_SYS_64BIT_VSPRINTF	/* needed for nand_util.c */
-#endif
-
-/*
- * SPI Flash configuration
- */
-#ifdef CONFIG_CMD_SF
-#define CONFIG_SPI_FLASH		1
-#define CONFIG_HARD_SPI			1
-#define CONFIG_KIRKWOOD_SPI		1
-#define CONFIG_SPI_FLASH_MACRONIX	1
-#define CONFIG_ENV_SPI_BUS		0
-#define CONFIG_ENV_SPI_CS		0
-#define CONFIG_ENV_SPI_MAX_HZ		50000000	/*50Mhz */
-#endif
-
-/*
  * Size of malloc() pool
  */
 #define CONFIG_SYS_MALLOC_LEN	(1024 * 1024) /* 1MiB for malloc() */
@@ -176,9 +103,7 @@
 #define CONFIG_CMDLINE_EDITING
 #define CONFIG_CONSOLE_INFO_QUIET	/* some code reduction */
 #define CONFIG_ARCH_CPU_INIT	/* call arch_cpu_init() */
-#ifndef CONFIG_ARMADA100	/* will be removed latter */
 #define CONFIG_ARCH_MISC_INIT	/* call arch_misc_init() */
-#endif /* CONFIG_ARMADA100 */
 #define CONFIG_BOARD_EARLY_INIT_F /* call board_init_f for early inits */
 #define CONFIG_DISPLAY_CPUINFO	/* Display cpu info */
 #define CONFIG_STACKSIZE	0x00100000	/* regular stack- 1M */
@@ -199,27 +124,32 @@
 #endif
 #endif /* CONFIG_NR_DRAM_BANKS */
 
+/* ====> Include platform Common Definations */
+#include <asm/arch/config.h>
+
+/* ====> Include driver Common Definations */
 /*
- * Ethernet Driver configuration
+ * Common NAND configuration
  */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_CMD_MII
-#define CONFIG_NETCONSOLE	/* include NetConsole support   */
-#define CONFIG_NET_MULTI	/* specify more that one ports available */
-#define CONFIG_MII		/* expose smi ove miiphy interface */
-#define CONFIG_MVGBE		/* Enable Marvell Gbe Controller Driver */
-#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */
-#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
-#define CONFIG_RESET_PHY_R	/* use reset_phy() to init mv8831116 PHY */
-#endif /* CONFIG_CMD_NET */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_SYS_MAX_NAND_DEVICE     1
+#define NAND_MAX_CHIPS                 1
+#define CONFIG_SYS_64BIT_VSPRINTF      /* needed for nand_util.c */
+#endif
+
+/*
+ * Common SPI Flash configuration
+ */
+#ifdef CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH		1
+#define CONFIG_SPI_FLASH_MACRONIX	1
+#endif
 
 /*
- * USB/EHCI
+ * Common USB/EHCI configuration
  */
 #ifdef CONFIG_CMD_USB
 #define CONFIG_USB_EHCI		/* Enable EHCI USB support */
-#define CONFIG_USB_EHCI_KIRKWOOD
-#define CONFIG_EHCI_IS_TDI
 #define CONFIG_USB_STORAGE
 #define CONFIG_DOS_PARTITION
 #define CONFIG_ISO_PARTITION
@@ -227,44 +157,9 @@
 #endif /* CONFIG_CMD_USB */
 
 /*
- * IDE Support on SATA ports
- */
-#ifdef CONFIG_CMD_IDE
-#define __io
-#define CONFIG_CMD_EXT2
-#define CONFIG_MVSATA_IDE
-#define CONFIG_IDE_PREINIT
-#define CONFIG_MVSATA_IDE_USE_PORT1
-/* Needs byte-swapping for ATA data register */
-#define CONFIG_IDE_SWAP_IO
-/* Data, registers and alternate blocks are at the same offset */
-#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
-#define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
-#define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
-/* Each 8-bit ATA register is aligned to a 4-bytes address */
-#define CONFIG_SYS_ATA_STRIDE		4
-/* Controller supports 48-bits LBA addressing */
-#define CONFIG_LBA48
-/* CONFIG_CMD_IDE requires some #defines for ATA registers */
-#define CONFIG_SYS_IDE_MAXBUS		2
-#define CONFIG_SYS_IDE_MAXDEVICE	2
-/* ATA registers base is at SATA controller base */
-#define CONFIG_SYS_ATA_BASE_ADDR	MV_SATA_BASE
-#endif /* CONFIG_CMD_IDE */
-
-/*
- * I2C related stuff
- */
-#ifdef CONFIG_CMD_I2C
-#define CONFIG_I2C_MVTWSI
-#define CONFIG_SYS_I2C_SLAVE		0x0
-#define CONFIG_SYS_I2C_SPEED		100000
-#endif
-
-/*
  * File system
  */
-#ifndef CONFIG_ARMADA100	/* will be removed latter */
+#ifdef CONFIG_SYS_MVFS
 #define CONFIG_CMD_EXT2
 #define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_FAT
@@ -275,6 +170,6 @@
 #define CONFIG_MTD_PARTITIONS
 #define CONFIG_CMD_MTDPARTS
 #define CONFIG_LZO
-#endif /* CONFIG_ARMADA100 */
+#endif
 
 #endif /* _MV_COMMON_H */
-- 
1.7.0.4

^ permalink raw reply related	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V8 2/5] ARM: Add Support for Marvell Pantheon Familiy SoCs
  2011-01-26 10:31 ` [U-Boot] [PATCH V7 0/5] Add Pantheon soc and dkb board support Lei Wen
  2011-01-28  9:19   ` [U-Boot] [PATCH V8 " Lei Wen
  2011-01-28  9:19   ` [U-Boot] [PATCH V8 1/5] mv: seperate kirkwood and armada from common setting Lei Wen
@ 2011-01-28  9:19   ` Lei Wen
  2011-01-28  9:19   ` [U-Boot] [PATCH V8 3/5] serial: add pantheon soc support Lei Wen
                     ` (2 subsequent siblings)
  5 siblings, 0 replies; 26+ messages in thread
From: Lei Wen @ 2011-01-28  9:19 UTC (permalink / raw)
  To: u-boot

Pantheon Family processors are highly integrated SoCs
based on Sheeva_88SV331x-v5 PJ1 cpu core.
Ref:
http://www.marvell.com/products/processors/communications/marvell_pantheon_910_920_pb.pdf

SoC versions Supported:
1) PANTHEON920          (TD)
2) PANTHEON910          (TTC)

Signed-off-by: Lei Wen <leiwen@marvell.com>
---
V2:

V3:
Fix copyright claim year.

V4:
Add change log to each patch.

V5:
coding style fix.

V6:
Rebase patch on latest u-boot-marvell.git.

V7:
Fix timer read to avoid potential optimization out of loop.

V8:
Fix copyright claim year.

 arch/arm/cpu/arm926ejs/pantheon/Makefile      |   46 ++++++
 arch/arm/cpu/arm926ejs/pantheon/cpu.c         |   78 +++++++++
 arch/arm/cpu/arm926ejs/pantheon/dram.c        |  132 +++++++++++++++
 arch/arm/cpu/arm926ejs/pantheon/timer.c       |  214 +++++++++++++++++++++++++
 arch/arm/include/asm/arch-pantheon/config.h   |   38 +++++
 arch/arm/include/asm/arch-pantheon/cpu.h      |   79 +++++++++
 arch/arm/include/asm/arch-pantheon/pantheon.h |   54 ++++++
 7 files changed, 641 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/Makefile
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/cpu.c
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/dram.c
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/timer.c
 create mode 100644 arch/arm/include/asm/arch-pantheon/config.h
 create mode 100644 arch/arm/include/asm/arch-pantheon/cpu.h
 create mode 100644 arch/arm/include/asm/arch-pantheon/pantheon.h

diff --git a/arch/arm/cpu/arm926ejs/pantheon/Makefile b/arch/arm/cpu/arm926ejs/pantheon/Makefile
new file mode 100644
index 0000000..ab94985
--- /dev/null
+++ b/arch/arm/cpu/arm926ejs/pantheon/Makefile
@@ -0,0 +1,46 @@
+#
+# (C) Copyright 2011
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Lei Wen <leiwen@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(SOC).o
+
+COBJS-y	= cpu.o timer.o dram.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS-y))
+
+all:	$(obj).depend $(LIB)
+
+$(LIB):	$(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/arch/arm/cpu/arm926ejs/pantheon/cpu.c b/arch/arm/cpu/arm926ejs/pantheon/cpu.c
new file mode 100644
index 0000000..9ddc77c
--- /dev/null
+++ b/arch/arm/cpu/arm926ejs/pantheon/cpu.c
@@ -0,0 +1,78 @@
+/*
+ * (C) Copyright 2011
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <asm/arch/pantheon.h>
+#include <asm/io.h>
+
+#define UARTCLK14745KHZ	(APBC_APBCLK | APBC_FNCLK | APBC_FNCLKSEL(1))
+#define SET_MRVL_ID	(1<<8)
+#define L2C_RAM_SEL	(1<<4)
+
+int arch_cpu_init(void)
+{
+	u32 val;
+	struct panthcpu_registers *cpuregs =
+		(struct panthcpu_registers*) PANTHEON_CPU_BASE;
+
+	struct panthapb_registers *apbclkres =
+		(struct panthapb_registers*) PANTHEON_APBC_BASE;
+
+	struct panthmpmu_registers *mpmu =
+		(struct panthmpmu_registers*) PANTHEON_MPMU_BASE;
+
+	/* set SEL_MRVL_ID bit in PANTHEON_CPU_CONF register */
+	val = readl(&cpuregs->cpu_conf);
+	val = val | SET_MRVL_ID;
+	writel(val, &cpuregs->cpu_conf);
+
+	/* Turn on clock gating (PMUM_CCGR) */
+	writel(0xFFFFFFFF, &mpmu->ccgr);
+
+	/* Turn on clock gating (PMUM_ACGR) */
+	writel(0xFFFFFFFF, &mpmu->acgr);
+
+	/* Turn on uart2 clock */
+	writel(UARTCLK14745KHZ, &apbclkres->uart0);
+
+	/* Enable GPIO clock */
+	writel(APBC_APBCLK, &apbclkres->gpio);
+
+	icache_enable();
+
+	return 0;
+}
+
+#if defined(CONFIG_DISPLAY_CPUINFO)
+int print_cpuinfo(void)
+{
+	u32 id;
+	struct panthcpu_registers *cpuregs =
+		(struct panthcpu_registers*) PANTHEON_CPU_BASE;
+
+	id = readl(&cpuregs->chip_id);
+	printf("SoC:   PANTHEON 88AP%X-%X\n", (id & 0xFFF), (id >> 0x10));
+	return 0;
+}
+#endif
diff --git a/arch/arm/cpu/arm926ejs/pantheon/dram.c b/arch/arm/cpu/arm926ejs/pantheon/dram.c
new file mode 100644
index 0000000..bbca7ee
--- /dev/null
+++ b/arch/arm/cpu/arm926ejs/pantheon/dram.c
@@ -0,0 +1,132 @@
+/*
+ * (C) Copyright 2011
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>,
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <asm/arch/pantheon.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Pantheon DRAM controller supports upto 8 banks
+ * for chip select 0 and 1
+ */
+
+/*
+ * DDR Memory Control Registers
+ * Refer Datasheet 4.4
+ */
+struct panthddr_map_registers {
+	u32	cs;	/* Memory Address Map Register -CS */
+	u32	pad[3];
+};
+
+struct panthddr_registers {
+	u8	pad[0x100 - 0x000];
+	struct panthddr_map_registers mmap[2];
+};
+
+/*
+ * panth_sdram_base - reads SDRAM Base Address Register
+ */
+u32 panth_sdram_base(int chip_sel)
+{
+	struct panthddr_registers *ddr_regs =
+		(struct panthddr_registers *)PANTHEON_DRAM_BASE;
+	u32 result = 0;
+	u32 CS_valid = 0x01 & readl(&ddr_regs->mmap[chip_sel].cs);
+
+	if (!CS_valid)
+		return 0;
+
+	result = readl(&ddr_regs->mmap[chip_sel].cs) & 0xFF800000;
+	return result;
+}
+
+/*
+ * panth_sdram_size - reads SDRAM size
+ */
+u32 panth_sdram_size(int chip_sel)
+{
+	struct panthddr_registers *ddr_regs =
+		(struct panthddr_registers *)PANTHEON_DRAM_BASE;
+	u32 result = 0;
+	u32 CS_valid = 0x01 & readl(&ddr_regs->mmap[chip_sel].cs);
+
+	if (!CS_valid)
+		return 0;
+
+	result = readl(&ddr_regs->mmap[chip_sel].cs);
+	result = (result >> 16) & 0xF;
+	if (result < 0x7) {
+		printf("Unknown DRAM Size\n");
+		return -1;
+	} else {
+		return ((0x8 << (result - 0x7)) * 1024 * 1024);
+	}
+}
+
+#ifndef CONFIG_SYS_BOARD_DRAM_INIT
+int dram_init(void)
+{
+	int i;
+
+	gd->ram_size = 0;
+	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+		gd->bd->bi_dram[i].start = panth_sdram_base(i);
+		gd->bd->bi_dram[i].size = panth_sdram_size(i);
+		/*
+		 * It is assumed that all memory banks are consecutive
+		 * and without gaps.
+		 * If the gap is found, ram_size will be reported for
+		 * consecutive memory only
+		 */
+		if (gd->bd->bi_dram[i].start != gd->ram_size)
+			break;
+
+		gd->ram_size += gd->bd->bi_dram[i].size;
+
+	}
+
+	for (; i < CONFIG_NR_DRAM_BANKS; i++) {
+		/*
+		 * If above loop terminated prematurely, we need to set
+		 * remaining banks' start address & size as 0. Otherwise other
+		 * u-boot functions and Linux kernel gets wrong values which
+		 * could result in crash
+		 */
+		gd->bd->bi_dram[i].start = 0;
+		gd->bd->bi_dram[i].size = 0;
+	}
+	return 0;
+}
+
+/*
+ * If this function is not defined here,
+ * board.c alters dram bank zero configuration defined above.
+ */
+void dram_init_banksize(void)
+{
+	dram_init();
+}
+#endif /* CONFIG_SYS_BOARD_DRAM_INIT */
diff --git a/arch/arm/cpu/arm926ejs/pantheon/timer.c b/arch/arm/cpu/arm926ejs/pantheon/timer.c
new file mode 100644
index 0000000..ca7f7f0
--- /dev/null
+++ b/arch/arm/cpu/arm926ejs/pantheon/timer.c
@@ -0,0 +1,214 @@
+/*
+ * (C) Copyright 2011
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <asm/arch/pantheon.h>
+
+/*
+ * Timer registers
+ * Refer 6.2.9 in Datasheet
+ */
+struct panthtmr_registers {
+	u32 clk_ctrl;	/* Timer clk control reg */
+	u32 match[9];	/* Timer match registers */
+	u32 count[3];	/* Timer count registers */
+	u32 status[3];
+	u32 ie[3];
+	u32 preload[3];	/* Timer preload value */
+	u32 preload_ctrl[3];
+	u32 wdt_match_en;
+	u32 wdt_match_r;
+	u32 wdt_val;
+	u32 wdt_sts;
+	u32 icr[3];
+	u32 wdt_icr;
+	u32 cer;	/* Timer count enable reg */
+	u32 cmr;
+	u32 ilr[3];
+	u32 wcr;
+	u32 wfar;
+	u32 wsar;
+	u32 cvwr[3];
+};
+
+#define TIMER			0	/* Use TIMER 0 */
+/* Each timer has 3 match registers */
+#define MATCH_CMP(x)		((3 * TIMER) + x)
+#define TIMER_LOAD_VAL 		0xffffffff
+#define	COUNT_RD_REQ		0x1
+
+DECLARE_GLOBAL_DATA_PTR;
+/* Using gd->tbu from timestamp and gd->tbl for lastdec */
+
+/*
+ * For preventing risk of instability in reading counter value,
+ * first set read request to register cvwr and then read same
+ * register after it captures counter value.
+ */
+ulong read_timer(void)
+{
+	struct panthtmr_registers *panthtimers =
+		(struct panthtmr_registers *) PANTHEON_TIMER_BASE;
+	volatile int loop=100;
+	ulong val;
+
+	writel(COUNT_RD_REQ, &panthtimers->cvwr);
+	while (loop--)
+		val = readl(&panthtimers->cvwr);
+
+	/*
+	 * This stop gcc complain and prevent loop mistake init to 0
+	 */
+	val = readl(&panthtimers->cvwr);
+
+	return val;
+}
+
+void reset_timer_masked(void)
+{
+	/* reset time */
+	gd->tbl = read_timer();
+	gd->tbu = 0;
+}
+
+ulong get_timer_masked(void)
+{
+	ulong now = read_timer();
+
+	if (now >= gd->tbl) {
+		/* normal mode */
+		gd->tbu += now - gd->tbl;
+	} else {
+		/* we have an overflow ... */
+		gd->tbu += now + TIMER_LOAD_VAL - gd->tbl;
+	}
+	gd->tbl = now;
+
+	return gd->tbu;
+}
+
+void reset_timer(void)
+{
+	reset_timer_masked();
+}
+
+ulong get_timer(ulong base)
+{
+	return ((get_timer_masked() / (CONFIG_SYS_HZ_CLOCK / 1000)) -
+		base);
+}
+
+void set_timer(ulong t)
+{
+	gd->tbu = t;
+}
+
+void __udelay(unsigned long usec)
+{
+	ulong delayticks;
+	ulong endtime;
+
+	delayticks = (usec * (CONFIG_SYS_HZ_CLOCK / 1000000));
+	endtime = get_timer_masked() + delayticks;
+
+	while (get_timer_masked() < endtime)
+		;
+}
+
+/*
+ * init the Timer
+ */
+int timer_init(void)
+{
+	struct panthapb_registers *apb1clkres =
+		(struct panthapb_registers *) PANTHEON_APBC_BASE;
+	struct panthtmr_registers *panthtimers =
+		(struct panthtmr_registers *) PANTHEON_TIMER_BASE;
+
+	/* Enable Timer clock@3.25 MHZ */
+	writel(APBC_APBCLK | APBC_FNCLK | APBC_FNCLKSEL(3), &apb1clkres->timers);
+
+	/* load value into timer */
+	writel(0x0, &panthtimers->clk_ctrl);
+	/* Use Timer 0 Match Resiger 0 */
+	writel(TIMER_LOAD_VAL, &panthtimers->match[MATCH_CMP(0)]);
+	/* Preload value is 0 */
+	writel(0x0, &panthtimers->preload[TIMER]);
+	/* Enable match comparator 0 for Timer 0 */
+	writel(0x1, &panthtimers->preload_ctrl[TIMER]);
+
+	/* Enable timer 0 */
+	writel(0x1, &panthtimers->cer);
+	/* init the gd->tbu and gd->tbl value */
+	reset_timer_masked();
+
+	return 0;
+}
+
+#define MPMU_APRR_WDTR	(1<<4)
+#define TMR_WFAR	0xbaba	/* WDT Register First key */
+#define TMP_WSAR	0xeb10	/* WDT Register Second key */
+
+/*
+ * This function uses internal Watchdog Timer
+ * based reset mechanism.
+ * Steps to write watchdog registers (protected access)
+ * 1. Write key value to TMR_WFAR reg.
+ * 2. Write key value to TMP_WSAR reg.
+ * 3. Perform write operation.
+ */
+void reset_cpu (unsigned long ignored)
+{
+	struct panthmpmu_registers *mpmu =
+		(struct panthmpmu_registers *) PANTHEON_MPMU_BASE;
+	struct panthtmr_registers *panthtimers =
+		(struct panthtmr_registers *) PANTHEON_WD_TIMER_BASE;
+	u32 val;
+
+	/* negate hardware reset to the WDT after system reset */
+	val = readl(&mpmu->aprr);
+	val = val | MPMU_APRR_WDTR;
+	writel(val, &mpmu->aprr);
+
+	/* reset/enable WDT clock */
+	writel(APBC_APBCLK, &mpmu->wdtpcr);
+
+	/* clear previous WDT status */
+	writel(TMR_WFAR, &panthtimers->wfar);
+	writel(TMP_WSAR, &panthtimers->wsar);
+	writel(0, &panthtimers->wdt_sts);
+
+	/* set match counter */
+	writel(TMR_WFAR, &panthtimers->wfar);
+	writel(TMP_WSAR, &panthtimers->wsar);
+	writel(0xf, &panthtimers->wdt_match_r);
+
+	/* enable WDT reset */
+	writel(TMR_WFAR, &panthtimers->wfar);
+	writel(TMP_WSAR, &panthtimers->wsar);
+	writel(0x3, &panthtimers->wdt_match_en);
+
+	/*enable functional WDT clock */
+	writel(APBC_APBCLK | APBC_FNCLK, &mpmu->wdtpcr);
+}
diff --git a/arch/arm/include/asm/arch-pantheon/config.h b/arch/arm/include/asm/arch-pantheon/config.h
new file mode 100644
index 0000000..710b386
--- /dev/null
+++ b/arch/arm/include/asm/arch-pantheon/config.h
@@ -0,0 +1,38 @@
+/*
+ * (C) Copyright 2011
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _PANTHEON_CONFIG_H
+#define _PANTHEON_CONFIG_H
+
+#define CONFIG_ARM926EJS	1	/* Basic Architecture */
+
+#define CONFIG_SYS_TCLK		(14745600)	/* NS16550 clk config */
+#define CONFIG_SYS_HZ_CLOCK	(3250000)	/* Timer Freq. 3.25MHZ */
+#define CONFIG_MARVELL_MFP			/* Enable mvmfp driver */
+#define MV_MFPR_BASE		PANTHEON_MFPR_BASE
+#define MV_UART_CONSOLE_BASE	PANTHEON_UART1_BASE
+#define CONFIG_SYS_NS16550_IER	(1 << 6)	/* Bit 6 in UART_IER register
+						represents UART Unit Enable */
+
+#endif /* _PANTHEON_CONFIG_H */
diff --git a/arch/arm/include/asm/arch-pantheon/cpu.h b/arch/arm/include/asm/arch-pantheon/cpu.h
new file mode 100644
index 0000000..30f4393
--- /dev/null
+++ b/arch/arm/include/asm/arch-pantheon/cpu.h
@@ -0,0 +1,79 @@
+/*
+ * (C) Copyright 2011
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _PANTHEON_CPU_H
+#define _PANTHEON_CPU_H
+
+#include <asm/io.h>
+#include <asm/system.h>
+
+/*
+ * Main Power Management (MPMU) Registers
+ * Refer Register Datasheet 9.1
+ */
+struct panthmpmu_registers {
+	u8 pad0[0x0024];
+	u32 ccgr;	/*0x0024*/
+	u8 pad1[0x0200 - 0x024 - 4];
+	u32 wdtpcr;	/*0x0200*/
+	u8 pad2[0x1020 - 0x200 - 4];
+	u32 aprr;	/*0x1020*/
+	u32 acgr;	/*0x1024*/
+};
+
+/*
+ * APB Clock Reset/Control Registers
+ * Refer Register Datasheet 6.14
+ */
+struct panthapb_registers {
+	u32 uart0;	/*0x000*/
+	u32 uart1;	/*0x004*/
+	u32 gpio;	/*0x008*/
+	u8 pad0[0x034 - 0x08 - 4];
+	u32 timers;	/*0x034*/
+};
+
+/*
+ * CPU Interface Registers
+ * Refer Register Datasheet 4.3
+ */
+struct panthcpu_registers {
+	u32 chip_id;		/* Chip Id Reg */
+	u32 pad;
+	u32 cpu_conf;		/* CPU Conf Reg */
+	u32 pad1;
+	u32 cpu_sram_spd;	/* CPU SRAM Speed Reg */
+	u32 pad2;
+	u32 cpu_l2c_spd;	/* CPU L2cache Speed Conf */
+	u32 mcb_conf;		/* MCB Conf Reg */
+	u32 sys_boot_ctl;	/* Sytem Boot Control */
+};
+
+/*
+ * Functions
+ */
+u32 panth_sdram_base(int);
+u32 panth_sdram_size(int);
+
+#endif /* _PANTHEON_CPU_H */
diff --git a/arch/arm/include/asm/arch-pantheon/pantheon.h b/arch/arm/include/asm/arch-pantheon/pantheon.h
new file mode 100644
index 0000000..e4ed087
--- /dev/null
+++ b/arch/arm/include/asm/arch-pantheon/pantheon.h
@@ -0,0 +1,54 @@
+/*
+ * (C) Copyright 2011
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _PANTHEON_H
+#define _PANTHEON_H
+
+#ifndef __ASSEMBLY__
+#include <asm/types.h>
+#include <asm/io.h>
+#endif	/* __ASSEMBLY__ */
+
+#include <asm/arch/cpu.h>
+
+/* Common APB clock register bit definitions */
+#define APBC_APBCLK     (1<<0)  /* APB Bus Clock Enable */
+#define APBC_FNCLK      (1<<1)  /* Functional Clock Enable */
+#define APBC_RST        (1<<2)  /* Reset Generation */
+/* Functional Clock Selection Mask */
+#define APBC_FNCLKSEL(x)        (((x) & 0xf) << 4)
+
+/* Register Base Addresses */
+#define PANTHEON_DRAM_BASE	0xB0000000
+#define PANTHEON_TIMER_BASE	0xD4014000
+#define PANTHEON_WD_TIMER_BASE	0xD4080000
+#define PANTHEON_APBC_BASE	0xD4015000
+#define PANTHEON_UART1_BASE	0xD4017000
+#define PANTHEON_UART2_BASE	0xD4018000
+#define PANTHEON_GPIO_BASE	0xD4019000
+#define PANTHEON_MFPR_BASE	0xD401E000
+#define PANTHEON_MPMU_BASE	0xD4050000
+#define PANTHEON_CPU_BASE	0xD4282C00
+
+#endif /* _PANTHEON_H */
-- 
1.7.0.4

^ permalink raw reply related	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V8 3/5] serial: add pantheon soc support
  2011-01-26 10:31 ` [U-Boot] [PATCH V7 0/5] Add Pantheon soc and dkb board support Lei Wen
                     ` (2 preceding siblings ...)
  2011-01-28  9:19   ` [U-Boot] [PATCH V8 2/5] ARM: Add Support for Marvell Pantheon Familiy SoCs Lei Wen
@ 2011-01-28  9:19   ` Lei Wen
  2011-01-28  9:19   ` [U-Boot] [PATCH V8 4/5] mvmfp: add MFP configuration support for PANTHEON Lei Wen
  2011-01-28  9:19   ` [U-Boot] [PATCH V8 5/5] Pantheon: Add Board Support for Marvell dkb board Lei Wen
  5 siblings, 0 replies; 26+ messages in thread
From: Lei Wen @ 2011-01-28  9:19 UTC (permalink / raw)
  To: u-boot

Signed-off-by: Lei Wen <leiwen@marvell.com>
---
V2:

V3:
Fix copyright claim year.

V4:
Add change log to each patch.

V5:

V6:
Rebase patch on latest u-boot-marvell.git.

V7:

V8:
Fix copyright claim year.

 drivers/serial/serial.c |    2 ++
 1 files changed, 2 insertions(+), 0 deletions(-)

diff --git a/drivers/serial/serial.c b/drivers/serial/serial.c
index cd3439e..4032dfd 100644
--- a/drivers/serial/serial.c
+++ b/drivers/serial/serial.c
@@ -33,6 +33,8 @@
 #include <asm/arch/orion5x.h>
 #elif defined(CONFIG_ARMADA100)
 #include <asm/arch/armada100.h>
+#elif defined(CONFIG_PANTHEON)
+#include <asm/arch/pantheon.h>
 #endif
 
 #if defined (CONFIG_SERIAL_MULTI)
-- 
1.7.0.4

^ permalink raw reply related	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V8 4/5] mvmfp: add MFP configuration support for PANTHEON
  2011-01-26 10:31 ` [U-Boot] [PATCH V7 0/5] Add Pantheon soc and dkb board support Lei Wen
                     ` (3 preceding siblings ...)
  2011-01-28  9:19   ` [U-Boot] [PATCH V8 3/5] serial: add pantheon soc support Lei Wen
@ 2011-01-28  9:19   ` Lei Wen
  2011-01-28  9:19   ` [U-Boot] [PATCH V8 5/5] Pantheon: Add Board Support for Marvell dkb board Lei Wen
  5 siblings, 0 replies; 26+ messages in thread
From: Lei Wen @ 2011-01-28  9:19 UTC (permalink / raw)
  To: u-boot

This patch adds the Multiple Function Pin configuration support for
Marvell PANTHEON SoCs

Signed-off-by: Lei Wen <leiwen@marvell.com>
---
V2:

V3:
Fix copyright claim year.

V4:
Add change log to each patch.

V5:
coding style fix.

V6:
Rebase patch on latest u-boot-marvell.git.

V7:
Correct patch comments

V8:
Fix copyright claim year.

 arch/arm/include/asm/arch-pantheon/mfp.h |   41 ++++++++++++++++++++++++++++++
 drivers/gpio/mvmfp.c                     |    2 +
 2 files changed, 43 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/include/asm/arch-pantheon/mfp.h

diff --git a/arch/arm/include/asm/arch-pantheon/mfp.h b/arch/arm/include/asm/arch-pantheon/mfp.h
new file mode 100644
index 0000000..fb291cf
--- /dev/null
+++ b/arch/arm/include/asm/arch-pantheon/mfp.h
@@ -0,0 +1,41 @@
+/*
+ * Based on arch/arm/include/asm/arch-armada100/mfp.h
+ * (C) Copyright 2011
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __PANTHEON_MFP_H
+#define __PANTHEON_MFP_H
+
+/*
+ * Frequently used MFP Configuration macros for all PANTHEON family of SoCs
+ *
+ * offset, pull,pF, drv,dF, edge,eF ,afn,aF
+ */
+/* UART2 */
+#define MFP47_UART2_RXD		MFP_REG(0x198) | MFP_AF6 | MFP_DRIVE_MEDIUM
+#define MFP48_UART2_TXD		MFP_REG(0x19c) | MFP_AF6 | MFP_DRIVE_MEDIUM
+
+/* More macros can be defined here... */
+
+#define MFP_PIN_MAX	117
+#endif
diff --git a/drivers/gpio/mvmfp.c b/drivers/gpio/mvmfp.c
index 5646ed4..e7830c6 100644
--- a/drivers/gpio/mvmfp.c
+++ b/drivers/gpio/mvmfp.c
@@ -28,6 +28,8 @@
 #include <asm/arch/mfp.h>
 #ifdef CONFIG_ARMADA100
 #include <asm/arch/armada100.h>
+#elif defined(CONFIG_PANTHEON)
+#include <asm/arch/pantheon.h>
 #else
 #error Unsupported SoC...
 #endif
-- 
1.7.0.4

^ permalink raw reply related	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V8 5/5] Pantheon: Add Board Support for Marvell dkb board
  2011-01-26 10:31 ` [U-Boot] [PATCH V7 0/5] Add Pantheon soc and dkb board support Lei Wen
                     ` (4 preceding siblings ...)
  2011-01-28  9:19   ` [U-Boot] [PATCH V8 4/5] mvmfp: add MFP configuration support for PANTHEON Lei Wen
@ 2011-01-28  9:19   ` Lei Wen
  5 siblings, 0 replies; 26+ messages in thread
From: Lei Wen @ 2011-01-28  9:19 UTC (permalink / raw)
  To: u-boot

DKB is a Development Board for PANTHEON TD/TTC(pxa920/pxa910) with
* Processor upto 806Mhz
* LPDDR1/2
* x8/x16 SLC/MLC NAND
* Footprints for eMMC & MMC x8 card

With Peripherals:
* Parallel LCD I/F
* Audio codecs (88PM8607)
* MIPI CSI-2 camera
* Marvell 88W8787 802.11n/BT module
* Marvell 2G/3G RF
* Dual analog mics & speakers, headset jack, LED, ambient
* USB2.0 HS host, OTG (mini AB)
* GPIO, GPIO expander with DIP switches for easier selection
* UART serial over USB, CIR

This patch adds basic board support with DRAM and UART functionality

Signed-off-by: Lei Wen <leiwen@marvell.com>
---
V2:

V3:
Fix copyright claim year.

V4:
Add change log to each patch.

V5:
Remove additional CONFIG_SYS_NS16550_COM1 definition in dkb.h

V6:
Rebase patch on latest u-boot-marvell.git.
And fix a build warning.

V7:

V8:
Fix copyright claim year.

 MAINTAINERS                |    4 +++
 board/Marvell/dkb/Makefile |   51 ++++++++++++++++++++++++++++++++++
 board/Marvell/dkb/dkb.c    |   54 ++++++++++++++++++++++++++++++++++++
 boards.cfg                 |    1 +
 include/configs/dkb.h      |   65 ++++++++++++++++++++++++++++++++++++++++++++
 5 files changed, 175 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/dkb/Makefile
 create mode 100644 board/Marvell/dkb/dkb.c
 create mode 100644 include/configs/dkb.h

diff --git a/MAINTAINERS b/MAINTAINERS
index d92ff8d..36e2516 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -850,6 +850,10 @@ Prafulla Wadaskar <prafulla@marvell.com>
 	rd6281a		ARM926EJS (Kirkwood SoC)
 	sheevaplug	ARM926EJS (Kirkwood SoC)
 
+Lei Wen <leiwen@marvell.com>
+
+	dkb		ARM926EJS (PANTHEON 88AP920 SOC)
+
 Matthias Weisser <weisserm@arcor.de>
 
 	jadecpu		ARM926EJS (MB86R01 SoC)
diff --git a/board/Marvell/dkb/Makefile b/board/Marvell/dkb/Makefile
new file mode 100644
index 0000000..2fafdb3
--- /dev/null
+++ b/board/Marvell/dkb/Makefile
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2011
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Lei Wen <leiwen@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB     = $(obj)lib$(BOARD).o
+
+COBJS	:= dkb.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/Marvell/dkb/dkb.c b/board/Marvell/dkb/dkb.c
new file mode 100644
index 0000000..72a2d2a
--- /dev/null
+++ b/board/Marvell/dkb/dkb.c
@@ -0,0 +1,54 @@
+/*
+ * (C) Copyright 2011
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <mvmfp.h>
+#include <asm/arch/mfp.h>
+#include <asm/arch/cpu.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+	u32 mfp_cfg[] = {
+		/* Enable Console on UART2 */
+		MFP47_UART2_RXD,
+		MFP48_UART2_TXD,
+
+		MFP_EOC		/*End of configureation*/
+	};
+	/* configure MFP's */
+	mfp_config(mfp_cfg);
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* arch number of Board */
+	gd->bd->bi_arch_number = MACH_TYPE_TTC_DKB;
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = panth_sdram_base(0) + 0x100;
+	return 0;
+}
diff --git a/boards.cfg b/boards.cfg
index 350f287..7e1e283 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -104,6 +104,7 @@ imx27lite                    arm         arm926ejs   imx27lite           logicpd
 magnesium                    arm         arm926ejs   imx27lite           logicpd        mx27
 omap5912osk                  arm         arm926ejs   -                   ti             omap
 edminiv2                     arm         arm926ejs   -                   LaCie          orion5x
+dkb			     arm         arm926ejs   -                   Marvell        pantheon
 ca9x4_ct_vxp                 arm         armv7       vexpress            armltd
 mx51evk                      arm         armv7       mx51evk             freescale      mx5
 mx53evk                      arm         armv7       mx53evk             freescale      mx5
diff --git a/include/configs/dkb.h b/include/configs/dkb.h
new file mode 100644
index 0000000..638af5e
--- /dev/null
+++ b/include/configs/dkb.h
@@ -0,0 +1,65 @@
+/*
+ * (C) Copyright 2011
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __CONFIG_DKB_H
+#define __CONFIG_DKB_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING	"\nMarvell-TTC DKB"
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_SHEEVA_88SV331xV5	1	/* CPU Core subversion */
+#define CONFIG_PANTHEON			1	/* SOC Family Name */
+#define CONFIG_MACH_TTC_DKB		1	/* Machine type */
+#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
+
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_TEXT_BASE - 0x00200000)
+#define CONFIG_NR_DRAM_BANKS_MAX	2
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH		/* Declare no flash (NOR/SPI) */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_AUTOSCRIPT
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+#undef CONFIG_ARCH_MISC_INIT
+/*
+ * Environment variables configurations
+ */
+#define CONFIG_ENV_IS_NOWHERE	1	/* if env in SDRAM */
+#define CONFIG_ENV_SIZE	0x20000	/* 64k */
+
+#endif	/* __CONFIG_DKB_H */
-- 
1.7.0.4

^ permalink raw reply related	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V7 1/5] mv: seperate kirkwood and armada from common setting
  2011-01-25  2:40 [U-Boot] [PATCH V6 0/5] Add Pantheon soc and dkb board support Lei Wen
                   ` (5 preceding siblings ...)
  2011-01-26 10:31 ` [U-Boot] [PATCH V7 0/5] Add Pantheon soc and dkb board support Lei Wen
@ 2011-01-26 10:31 ` Lei Wen
  2011-01-27 18:34   ` Albert ARIBAUD
  2011-01-26 10:31 ` [U-Boot] [PATCH V7 2/5] ARM: Add Support for Marvell Pantheon Familiy SoCs Lei Wen
                   ` (3 subsequent siblings)
  10 siblings, 1 reply; 26+ messages in thread
From: Lei Wen @ 2011-01-26 10:31 UTC (permalink / raw)
  To: u-boot

Since there are lots of difference between kirkwood and armada series,
it is better to seperate them but still keep the most common file
shared by all marvell platform in the mv-common configure file.

This patch move the kirkwood only driver definitoin in mv-common to
the <soc_name>/config.h.

This patch is tested with compilation for armada100 and guruplug.

Signed-off-by: Lei Wen <leiwen@marvell.com>
---
V2:
This patch seris update the seperate mv_common part as suggested.

V3:
Fix config.h include place and copyright claim year.

V4:
Add change log to each patch.

V5:
Add CONFIG_SYS_MVFS doc in README.

V6:
Rebase patch on latest u-boot-marvell.git.

V7:
Fix CONFIG_SYS_INIT_SP_ADDR put place.

 README                                       |    5 +
 arch/arm/include/asm/arch-armada100/config.h |   44 ++++++++
 arch/arm/include/asm/arch-kirkwood/config.h  |  145 +++++++++++++++++++++++++
 include/configs/aspenite.h                   |    8 ++
 include/configs/mv-common.h                  |  147 ++++----------------------
 5 files changed, 223 insertions(+), 126 deletions(-)
 create mode 100644 arch/arm/include/asm/arch-armada100/config.h
 create mode 100644 arch/arm/include/asm/arch-kirkwood/config.h

diff --git a/README b/README
index 755d17c..e0341b5 100644
--- a/README
+++ b/README
@@ -319,6 +319,11 @@ The following options need to be configured:
 			CONFIG_SYS_PQ2FADS	- PQ2FADS-ZU or PQ2FADS-VR
 			CONFIG_SYS_8272ADS	- MPC8272ADS
 
+- Marvell Family Member
+		CONFIG_SYS_MVFS		- define it if you want to enable
+					  multiply fs option at one time
+					  for marvell soc family
+
 - MPC824X Family Member (if CONFIG_MPC824X is defined)
 		Define exactly one of
 		CONFIG_MPC8240, CONFIG_MPC8245
diff --git a/arch/arm/include/asm/arch-armada100/config.h b/arch/arm/include/asm/arch-armada100/config.h
new file mode 100644
index 0000000..f16806e
--- /dev/null
+++ b/arch/arm/include/asm/arch-armada100/config.h
@@ -0,0 +1,44 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+/*
+ * This file should be included in board config header file.
+ *
+ * It supports common definitions for Armada100 platform
+ */
+
+#ifndef _ARMD1_CONFIG_H
+#define _ARMD1_CONFIG_H
+
+#define CONFIG_ARM926EJS	1	/* Basic Architecture */
+
+#define CONFIG_SYS_TCLK		(14745600)	/* NS16550 clk config */
+#define CONFIG_SYS_HZ_CLOCK	(3250000)	/* Timer Freq. 3.25MHZ */
+#define CONFIG_MARVELL_MFP			/* Enable mvmfp driver */
+#define MV_MFPR_BASE		ARMD1_MFPR_BASE
+#define MV_UART_CONSOLE_BASE	ARMD1_UART1_BASE
+#define CONFIG_SYS_NS16550_IER	(1 << 6)	/* Bit 6 in UART_IER register
+						represents UART Unit Enable */
+
+#endif /* _ARMD1_CONFIG_H */
diff --git a/arch/arm/include/asm/arch-kirkwood/config.h b/arch/arm/include/asm/arch-kirkwood/config.h
new file mode 100644
index 0000000..7c6d63b
--- /dev/null
+++ b/arch/arm/include/asm/arch-kirkwood/config.h
@@ -0,0 +1,145 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+/*
+ * This file should be included in board config header file.
+ *
+ * It supports common definitions for Kirkwood platform
+ */
+
+#ifndef _KW_CONFIG_H
+#define _KW_CONFIG_H
+
+#if defined (CONFIG_KW88F6281)
+#include <asm/arch/kw88f6281.h>
+#elif defined (CONFIG_KW88F6192)
+#include <asm/arch/kw88f6192.h>
+#else
+#error "SOC Name not defined"
+#endif /* CONFIG_KW88F6281 */
+
+#define CONFIG_ARM926EJS	1	/* Basic Architecture */
+
+#define CONFIG_MD5	/* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_KIRKWOOD_EGIGA_INIT	/* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8	/* Set RGMII Pad voltage to 1.8V */
+#define CONFIG_KIRKWOOD_PCIE_INIT       /* Enable PCIE Port0 for kernel */
+
+/*
+ * By default kwbimage.cfg from board specific folder is used
+ * If for some board, different configuration file need to be used,
+ * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
+ */
+#ifndef CONFIG_SYS_KWD_CONFIG
+#define	CONFIG_SYS_KWD_CONFIG	$(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage.cfg
+#endif /* CONFIG_SYS_KWD_CONFIG */
+
+/* Kirkwood has 2k of Security SRAM, use it for SP */
+#define CONFIG_SYS_INIT_SP_ADDR		0xC8012000
+#define CONFIG_NR_DRAM_BANKS_MAX	2
+
+#define CONFIG_I2C_MVTWSI_BASE	KW_TWSI_BASE
+#define MV_UART_CONSOLE_BASE	KW_UART0_BASE
+#define MV_SATA_BASE		KW_SATA_BASE
+#define MV_SATA_PORT0_OFFSET	KW_SATA_PORT0_OFFSET
+#define MV_SATA_PORT1_OFFSET	KW_SATA_PORT1_OFFSET
+
+/*
+ * NAND configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_KIRKWOOD
+#define CONFIG_SYS_NAND_BASE		0xD8000000	/* MV_DEFADR_NANDF */
+#define NAND_ALLOW_ERASE_ALL		1
+#endif
+
+/*
+ * SPI Flash configuration
+ */
+#ifdef CONFIG_CMD_SF
+#define CONFIG_HARD_SPI			1
+#define CONFIG_KIRKWOOD_SPI		1
+#define CONFIG_ENV_SPI_BUS		0
+#define CONFIG_ENV_SPI_CS		0
+#define CONFIG_ENV_SPI_MAX_HZ		50000000	/*50Mhz */
+#endif
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_NETCONSOLE	/* include NetConsole support   */
+#define CONFIG_NET_MULTI	/* specify more that one ports available */
+#define CONFIG_MII		/* expose smi ove miiphy interface */
+#define CONFIG_MVGBE		/* Enable Marvell Gbe Controller Driver */
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */
+#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
+#define CONFIG_RESET_PHY_R	/* use reset_phy() to init mv8831116 PHY */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * USB/EHCI
+ */
+#ifdef CONFIG_CMD_USB
+#define CONFIG_USB_EHCI_KIRKWOOD
+#define CONFIG_EHCI_IS_TDI
+#endif /* CONFIG_CMD_USB */
+
+/*
+ * IDE Support on SATA ports
+ */
+#ifdef CONFIG_CMD_IDE
+#define __io
+#define CONFIG_CMD_EXT2
+#define CONFIG_MVSATA_IDE
+#define CONFIG_IDE_PREINIT
+#define CONFIG_MVSATA_IDE_USE_PORT1
+/* Needs byte-swapping for ATA data register */
+#define CONFIG_IDE_SWAP_IO
+/* Data, registers and alternate blocks are at the same offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
+/* Each 8-bit ATA register is aligned to a 4-bytes address */
+#define CONFIG_SYS_ATA_STRIDE		4
+/* Controller supports 48-bits LBA addressing */
+#define CONFIG_LBA48
+/* CONFIG_CMD_IDE requires some #defines for ATA registers */
+#define CONFIG_SYS_IDE_MAXBUS		2
+#define CONFIG_SYS_IDE_MAXDEVICE	2
+/* ATA registers base is at SATA controller base */
+#define CONFIG_SYS_ATA_BASE_ADDR	MV_SATA_BASE
+#endif /* CONFIG_CMD_IDE */
+
+/*
+ * I2C related stuff
+ */
+#ifdef CONFIG_CMD_I2C
+#define CONFIG_I2C_MVTWSI
+#define CONFIG_SYS_I2C_SLAVE		0x0
+#define CONFIG_SYS_I2C_SPEED		100000
+#endif
+
+#endif /* _KW_CONFIG_H */
diff --git a/include/configs/aspenite.h b/include/configs/aspenite.h
index 706365f..fd35f3e 100644
--- a/include/configs/aspenite.h
+++ b/include/configs/aspenite.h
@@ -41,6 +41,13 @@
 #define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
 
 /*
+ * There is no internal RAM in ARMADA100, using DRAM
+ * TBD: dcache to be used for this
+ */
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_TEXT_BASE - 0x00200000)
+#define CONFIG_NR_DRAM_BANKS_MAX	2
+
+/*
  * Commands configuration
  */
 #define CONFIG_SYS_NO_FLASH		/* Declare no flash (NOR/SPI) */
@@ -53,6 +60,7 @@
  * to enable certain macros
  */
 #include "mv-common.h"
+#undef CONFIG_ARCH_MISC_INIT
 
 /*
  * Environment variables configurations
diff --git a/include/configs/mv-common.h b/include/configs/mv-common.h
index 97b6971..a8937dd 100644
--- a/include/configs/mv-common.h
+++ b/include/configs/mv-common.h
@@ -37,54 +37,6 @@
  * High Level Configuration Options (easy to change)
  */
 #define CONFIG_MARVELL		1
-#define CONFIG_ARM926EJS	1	/* Basic Architecture */
-
-/* ====> Kirkwood Platform Common Definations */
-#if defined(CONFIG_KIRKWOOD)
-#define CONFIG_MD5	/* get_random_hex on krikwood needs MD5 support */
-#define CONFIG_KIRKWOOD_EGIGA_INIT	/* Enable GbePort0/1 for kernel */
-#define CONFIG_KIRKWOOD_RGMII_PAD_1V8	/* Set RGMII Pad voltage to 1.8V */
-#define CONFIG_KIRKWOOD_PCIE_INIT       /* Enable PCIE Port0 for kernel */
-
-/*
- * By default kwbimage.cfg from board specific folder is used
- * If for some board, different configuration file need to be used,
- * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
- */
-#ifndef CONFIG_SYS_KWD_CONFIG
-#define	CONFIG_SYS_KWD_CONFIG	$(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage.cfg
-#endif /* CONFIG_SYS_KWD_CONFIG */
-
-/* Kirkwood has 2k of Security SRAM, use it for SP */
-#define CONFIG_SYS_INIT_SP_ADDR		0xC8012000
-#define CONFIG_NR_DRAM_BANKS_MAX	2
-
-#define CONFIG_I2C_MVTWSI_BASE	KW_TWSI_BASE
-#define MV_UART_CONSOLE_BASE	KW_UART0_BASE
-#define MV_SATA_BASE		KW_SATA_BASE
-#define MV_SATA_PORT0_OFFSET	KW_SATA_PORT0_OFFSET
-#define MV_SATA_PORT1_OFFSET	KW_SATA_PORT1_OFFSET
-
-/* ====> ARMADA100 Platform Common Definations */
-#elif defined (CONFIG_ARMADA100)
-
-#define CONFIG_SYS_TCLK		(14745600)	/* NS16550 clk config */
-#define CONFIG_SYS_HZ_CLOCK	(3250000)	/* Timer Freq. 3.25MHZ */
-#define CONFIG_MARVELL_MFP			/* Enable mvmfp driver */
-#define MV_MFPR_BASE		ARMD1_MFPR_BASE
-#define MV_UART_CONSOLE_BASE	ARMD1_UART1_BASE
-#define CONFIG_SYS_NS16550_IER	(1 << 6)	/* Bit 6 in UART_IER register
-						represents UART Unit Enable */
-/*
- * There is no internal RAM in ARMADA100, using DRAM
- * TBD: dcache to be used for this
- */
-#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_TEXT_BASE - 0x00200000)
-#define CONFIG_NR_DRAM_BANKS_MAX	2
-
-#else
-#error "Unsupported SoC Platform..."
-#endif
 
 /*
  * Custom CONFIG_SYS_TEXT_BASE can be done in <board>.h
@@ -138,31 +90,6 @@
 		+sizeof(CONFIG_SYS_PROMPT) + 16)	/* Print Buff */
 
 /*
- * NAND configuration
- */
-#ifdef CONFIG_CMD_NAND
-#define CONFIG_NAND_KIRKWOOD
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define NAND_MAX_CHIPS			1
-#define CONFIG_SYS_NAND_BASE		0xD8000000	/* MV_DEFADR_NANDF */
-#define NAND_ALLOW_ERASE_ALL		1
-#define CONFIG_SYS_64BIT_VSPRINTF	/* needed for nand_util.c */
-#endif
-
-/*
- * SPI Flash configuration
- */
-#ifdef CONFIG_CMD_SF
-#define CONFIG_SPI_FLASH		1
-#define CONFIG_HARD_SPI			1
-#define CONFIG_KIRKWOOD_SPI		1
-#define CONFIG_SPI_FLASH_MACRONIX	1
-#define CONFIG_ENV_SPI_BUS		0
-#define CONFIG_ENV_SPI_CS		0
-#define CONFIG_ENV_SPI_MAX_HZ		50000000	/*50Mhz */
-#endif
-
-/*
  * Size of malloc() pool
  */
 #define CONFIG_SYS_MALLOC_LEN	(1024 * 1024) /* 1MiB for malloc() */
@@ -176,9 +103,7 @@
 #define CONFIG_CMDLINE_EDITING
 #define CONFIG_CONSOLE_INFO_QUIET	/* some code reduction */
 #define CONFIG_ARCH_CPU_INIT	/* call arch_cpu_init() */
-#ifndef CONFIG_ARMADA100	/* will be removed latter */
 #define CONFIG_ARCH_MISC_INIT	/* call arch_misc_init() */
-#endif /* CONFIG_ARMADA100 */
 #define CONFIG_BOARD_EARLY_INIT_F /* call board_init_f for early inits */
 #define CONFIG_DISPLAY_CPUINFO	/* Display cpu info */
 #define CONFIG_STACKSIZE	0x00100000	/* regular stack- 1M */
@@ -199,27 +124,32 @@
 #endif
 #endif /* CONFIG_NR_DRAM_BANKS */
 
+/* ====> Include platform Common Definations */
+#include <asm/arch/config.h>
+
+/* ====> Include driver Common Definations */
 /*
- * Ethernet Driver configuration
+ * Common NAND configuration
  */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_CMD_MII
-#define CONFIG_NETCONSOLE	/* include NetConsole support   */
-#define CONFIG_NET_MULTI	/* specify more that one ports available */
-#define CONFIG_MII		/* expose smi ove miiphy interface */
-#define CONFIG_MVGBE		/* Enable Marvell Gbe Controller Driver */
-#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */
-#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
-#define CONFIG_RESET_PHY_R	/* use reset_phy() to init mv8831116 PHY */
-#endif /* CONFIG_CMD_NET */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_SYS_MAX_NAND_DEVICE     1
+#define NAND_MAX_CHIPS                 1
+#define CONFIG_SYS_64BIT_VSPRINTF      /* needed for nand_util.c */
+#endif
+
+/*
+ * Common SPI Flash configuration
+ */
+#ifdef CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH		1
+#define CONFIG_SPI_FLASH_MACRONIX	1
+#endif
 
 /*
- * USB/EHCI
+ * Common USB/EHCI configuration
  */
 #ifdef CONFIG_CMD_USB
 #define CONFIG_USB_EHCI		/* Enable EHCI USB support */
-#define CONFIG_USB_EHCI_KIRKWOOD
-#define CONFIG_EHCI_IS_TDI
 #define CONFIG_USB_STORAGE
 #define CONFIG_DOS_PARTITION
 #define CONFIG_ISO_PARTITION
@@ -227,44 +157,9 @@
 #endif /* CONFIG_CMD_USB */
 
 /*
- * IDE Support on SATA ports
- */
-#ifdef CONFIG_CMD_IDE
-#define __io
-#define CONFIG_CMD_EXT2
-#define CONFIG_MVSATA_IDE
-#define CONFIG_IDE_PREINIT
-#define CONFIG_MVSATA_IDE_USE_PORT1
-/* Needs byte-swapping for ATA data register */
-#define CONFIG_IDE_SWAP_IO
-/* Data, registers and alternate blocks are at the same offset */
-#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
-#define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
-#define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
-/* Each 8-bit ATA register is aligned to a 4-bytes address */
-#define CONFIG_SYS_ATA_STRIDE		4
-/* Controller supports 48-bits LBA addressing */
-#define CONFIG_LBA48
-/* CONFIG_CMD_IDE requires some #defines for ATA registers */
-#define CONFIG_SYS_IDE_MAXBUS		2
-#define CONFIG_SYS_IDE_MAXDEVICE	2
-/* ATA registers base is at SATA controller base */
-#define CONFIG_SYS_ATA_BASE_ADDR	MV_SATA_BASE
-#endif /* CONFIG_CMD_IDE */
-
-/*
- * I2C related stuff
- */
-#ifdef CONFIG_CMD_I2C
-#define CONFIG_I2C_MVTWSI
-#define CONFIG_SYS_I2C_SLAVE		0x0
-#define CONFIG_SYS_I2C_SPEED		100000
-#endif
-
-/*
  * File system
  */
-#ifndef CONFIG_ARMADA100	/* will be removed latter */
+#ifdef CONFIG_SYS_MVFS
 #define CONFIG_CMD_EXT2
 #define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_FAT
@@ -275,6 +170,6 @@
 #define CONFIG_MTD_PARTITIONS
 #define CONFIG_CMD_MTDPARTS
 #define CONFIG_LZO
-#endif /* CONFIG_ARMADA100 */
+#endif
 
 #endif /* _MV_COMMON_H */
-- 
1.7.0.4

^ permalink raw reply related	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V7 1/5] mv: seperate kirkwood and armada from common setting
  2011-01-26 10:31 ` [U-Boot] [PATCH V7 1/5] mv: seperate kirkwood and armada from common setting Lei Wen
@ 2011-01-27 18:34   ` Albert ARIBAUD
  2011-01-28  1:28     ` Lei Wen
  0 siblings, 1 reply; 26+ messages in thread
From: Albert ARIBAUD @ 2011-01-27 18:34 UTC (permalink / raw)
  To: u-boot

Hi Lei Wen,

Le 26/01/2011 11:31, Lei Wen a ?crit :

> diff --git a/README b/README
> index 755d17c..e0341b5 100644
> --- a/README
> +++ b/README
> @@ -319,6 +319,11 @@ The following options need to be configured:
>   			CONFIG_SYS_PQ2FADS	- PQ2FADS-ZU or PQ2FADS-VR
>   			CONFIG_SYS_8272ADS	- MPC8272ADS
>
> +- Marvell Family Member
> +		CONFIG_SYS_MVFS		- define it if you want to enable
> +					  multiply fs option at one time

Are you sure about this "multiply"?

> +					  for marvell soc family
> +
>   - MPC824X Family Member (if CONFIG_MPC824X is defined)
>   		Define exactly one of
>   		CONFIG_MPC8240, CONFIG_MPC8245
> diff --git a/arch/arm/include/asm/arch-armada100/config.h b/arch/arm/include/asm/arch-armada100/config.h
> new file mode 100644
> index 0000000..f16806e
> --- /dev/null
> +++ b/arch/arm/include/asm/arch-armada100/config.h
> @@ -0,0 +1,44 @@
> +/*
> + * (C) Copyright 2010

Maybe update the copyright year?

> + * Marvell Semiconductor<www.marvell.com>
> + * Written-by: Lei Wen<leiwen@marvell.com>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> + * MA 02110-1301 USA
> + */
> +
> +/*
> + * This file should be included in board config header file.
> + *
> + * It supports common definitions for Armada100 platform
> + */
> +
> +#ifndef _ARMD1_CONFIG_H
> +#define _ARMD1_CONFIG_H
> +
> +#define CONFIG_ARM926EJS	1	/* Basic Architecture */
> +
> +#define CONFIG_SYS_TCLK		(14745600)	/* NS16550 clk config */
> +#define CONFIG_SYS_HZ_CLOCK	(3250000)	/* Timer Freq. 3.25MHZ */
> +#define CONFIG_MARVELL_MFP			/* Enable mvmfp driver */
> +#define MV_MFPR_BASE		ARMD1_MFPR_BASE
> +#define MV_UART_CONSOLE_BASE	ARMD1_UART1_BASE
> +#define CONFIG_SYS_NS16550_IER	(1<<  6)	/* Bit 6 in UART_IER register
> +						represents UART Unit Enable */
> +
> +#endif /* _ARMD1_CONFIG_H */
> diff --git a/arch/arm/include/asm/arch-kirkwood/config.h b/arch/arm/include/asm/arch-kirkwood/config.h
> new file mode 100644
> index 0000000..7c6d63b
> --- /dev/null
> +++ b/arch/arm/include/asm/arch-kirkwood/config.h
> @@ -0,0 +1,145 @@
> +/*
> + * (C) Copyright 2010

Ditto

> + * Marvell Semiconductor<www.marvell.com>
> + * Written-by: Lei Wen<leiwen@marvell.com>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
> + * MA 02110-1301 USA
> + */
> +
> +/*
> + * This file should be included in board config header file.
> + *
> + * It supports common definitions for Kirkwood platform
> + */
> +
> +#ifndef _KW_CONFIG_H
> +#define _KW_CONFIG_H
> +
> +#if defined (CONFIG_KW88F6281)
> +#include<asm/arch/kw88f6281.h>
> +#elif defined (CONFIG_KW88F6192)
> +#include<asm/arch/kw88f6192.h>
> +#else
> +#error "SOC Name not defined"
> +#endif /* CONFIG_KW88F6281 */
> +
> +#define CONFIG_ARM926EJS	1	/* Basic Architecture */
> +
> +#define CONFIG_MD5	/* get_random_hex on krikwood needs MD5 support */
> +#define CONFIG_KIRKWOOD_EGIGA_INIT	/* Enable GbePort0/1 for kernel */
> +#define CONFIG_KIRKWOOD_RGMII_PAD_1V8	/* Set RGMII Pad voltage to 1.8V */
> +#define CONFIG_KIRKWOOD_PCIE_INIT       /* Enable PCIE Port0 for kernel */
> +
> +/*
> + * By default kwbimage.cfg from board specific folder is used
> + * If for some board, different configuration file need to be used,
> + * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
> + */
> +#ifndef CONFIG_SYS_KWD_CONFIG
> +#define	CONFIG_SYS_KWD_CONFIG	$(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage.cfg

What are the '$()' operators doing here ?

> +#endif /* CONFIG_SYS_KWD_CONFIG */
> +
> +/* Kirkwood has 2k of Security SRAM, use it for SP */
> +#define CONFIG_SYS_INIT_SP_ADDR		0xC8012000
> +#define CONFIG_NR_DRAM_BANKS_MAX	2
> +
> +#define CONFIG_I2C_MVTWSI_BASE	KW_TWSI_BASE
> +#define MV_UART_CONSOLE_BASE	KW_UART0_BASE
> +#define MV_SATA_BASE		KW_SATA_BASE
> +#define MV_SATA_PORT0_OFFSET	KW_SATA_PORT0_OFFSET
> +#define MV_SATA_PORT1_OFFSET	KW_SATA_PORT1_OFFSET
> +
> +/*
> + * NAND configuration
> + */
> +#ifdef CONFIG_CMD_NAND
> +#define CONFIG_NAND_KIRKWOOD
> +#define CONFIG_SYS_NAND_BASE		0xD8000000	/* MV_DEFADR_NANDF */
> +#define NAND_ALLOW_ERASE_ALL		1
> +#endif
> +
> +/*
> + * SPI Flash configuration
> + */
> +#ifdef CONFIG_CMD_SF
> +#define CONFIG_HARD_SPI			1
> +#define CONFIG_KIRKWOOD_SPI		1
> +#define CONFIG_ENV_SPI_BUS		0
> +#define CONFIG_ENV_SPI_CS		0
> +#define CONFIG_ENV_SPI_MAX_HZ		50000000	/*50Mhz */
> +#endif
> +
> +/*
> + * Ethernet Driver configuration
> + */
> +#ifdef CONFIG_CMD_NET
> +#define CONFIG_CMD_MII
> +#define CONFIG_NETCONSOLE	/* include NetConsole support   */
> +#define CONFIG_NET_MULTI	/* specify more that one ports available */
> +#define CONFIG_MII		/* expose smi ove miiphy interface */
> +#define CONFIG_MVGBE		/* Enable Marvell Gbe Controller Driver */
> +#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */
> +#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
> +#define CONFIG_RESET_PHY_R	/* use reset_phy() to init mv8831116 PHY */
> +#endif /* CONFIG_CMD_NET */
> +
> +/*
> + * USB/EHCI
> + */
> +#ifdef CONFIG_CMD_USB
> +#define CONFIG_USB_EHCI_KIRKWOOD
> +#define CONFIG_EHCI_IS_TDI
> +#endif /* CONFIG_CMD_USB */
> +
> +/*
> + * IDE Support on SATA ports
> + */
> +#ifdef CONFIG_CMD_IDE
> +#define __io
> +#define CONFIG_CMD_EXT2
> +#define CONFIG_MVSATA_IDE
> +#define CONFIG_IDE_PREINIT
> +#define CONFIG_MVSATA_IDE_USE_PORT1
> +/* Needs byte-swapping for ATA data register */
> +#define CONFIG_IDE_SWAP_IO
> +/* Data, registers and alternate blocks are at the same offset */
> +#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
> +#define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
> +#define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
> +/* Each 8-bit ATA register is aligned to a 4-bytes address */
> +#define CONFIG_SYS_ATA_STRIDE		4
> +/* Controller supports 48-bits LBA addressing */
> +#define CONFIG_LBA48
> +/* CONFIG_CMD_IDE requires some #defines for ATA registers */
> +#define CONFIG_SYS_IDE_MAXBUS		2
> +#define CONFIG_SYS_IDE_MAXDEVICE	2
> +/* ATA registers base is at SATA controller base */
> +#define CONFIG_SYS_ATA_BASE_ADDR	MV_SATA_BASE
> +#endif /* CONFIG_CMD_IDE */
> +
> +/*
> + * I2C related stuff
> + */
> +#ifdef CONFIG_CMD_I2C
> +#define CONFIG_I2C_MVTWSI
> +#define CONFIG_SYS_I2C_SLAVE		0x0
> +#define CONFIG_SYS_I2C_SPEED		100000
> +#endif
> +
> +#endif /* _KW_CONFIG_H */
> diff --git a/include/configs/aspenite.h b/include/configs/aspenite.h
> index 706365f..fd35f3e 100644
> --- a/include/configs/aspenite.h
> +++ b/include/configs/aspenite.h
> @@ -41,6 +41,13 @@
>   #define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
>
>   /*
> + * There is no internal RAM in ARMADA100, using DRAM
> + * TBD: dcache to be used for this
> + */
> +#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_TEXT_BASE - 0x00200000)
> +#define CONFIG_NR_DRAM_BANKS_MAX	2
> +
> +/*
>    * Commands configuration
>    */
>   #define CONFIG_SYS_NO_FLASH		/* Declare no flash (NOR/SPI) */
> @@ -53,6 +60,7 @@
>    * to enable certain macros
>    */
>   #include "mv-common.h"
> +#undef CONFIG_ARCH_MISC_INIT
>
>   /*
>    * Environment variables configurations
> diff --git a/include/configs/mv-common.h b/include/configs/mv-common.h
> index 97b6971..a8937dd 100644
> --- a/include/configs/mv-common.h
> +++ b/include/configs/mv-common.h
> @@ -37,54 +37,6 @@
>    * High Level Configuration Options (easy to change)
>    */
>   #define CONFIG_MARVELL		1
> -#define CONFIG_ARM926EJS	1	/* Basic Architecture */
> -
> -/* ====>  Kirkwood Platform Common Definations */
> -#if defined(CONFIG_KIRKWOOD)
> -#define CONFIG_MD5	/* get_random_hex on krikwood needs MD5 support */
> -#define CONFIG_KIRKWOOD_EGIGA_INIT	/* Enable GbePort0/1 for kernel */
> -#define CONFIG_KIRKWOOD_RGMII_PAD_1V8	/* Set RGMII Pad voltage to 1.8V */
> -#define CONFIG_KIRKWOOD_PCIE_INIT       /* Enable PCIE Port0 for kernel */
> -
> -/*
> - * By default kwbimage.cfg from board specific folder is used
> - * If for some board, different configuration file need to be used,
> - * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
> - */
> -#ifndef CONFIG_SYS_KWD_CONFIG
> -#define	CONFIG_SYS_KWD_CONFIG	$(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage.cfg
> -#endif /* CONFIG_SYS_KWD_CONFIG */
> -
> -/* Kirkwood has 2k of Security SRAM, use it for SP */
> -#define CONFIG_SYS_INIT_SP_ADDR		0xC8012000
> -#define CONFIG_NR_DRAM_BANKS_MAX	2
> -
> -#define CONFIG_I2C_MVTWSI_BASE	KW_TWSI_BASE
> -#define MV_UART_CONSOLE_BASE	KW_UART0_BASE
> -#define MV_SATA_BASE		KW_SATA_BASE
> -#define MV_SATA_PORT0_OFFSET	KW_SATA_PORT0_OFFSET
> -#define MV_SATA_PORT1_OFFSET	KW_SATA_PORT1_OFFSET
> -
> -/* ====>  ARMADA100 Platform Common Definations */
> -#elif defined (CONFIG_ARMADA100)
> -
> -#define CONFIG_SYS_TCLK		(14745600)	/* NS16550 clk config */
> -#define CONFIG_SYS_HZ_CLOCK	(3250000)	/* Timer Freq. 3.25MHZ */
> -#define CONFIG_MARVELL_MFP			/* Enable mvmfp driver */
> -#define MV_MFPR_BASE		ARMD1_MFPR_BASE
> -#define MV_UART_CONSOLE_BASE	ARMD1_UART1_BASE
> -#define CONFIG_SYS_NS16550_IER	(1<<  6)	/* Bit 6 in UART_IER register
> -						represents UART Unit Enable */
> -/*
> - * There is no internal RAM in ARMADA100, using DRAM
> - * TBD: dcache to be used for this
> - */
> -#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_TEXT_BASE - 0x00200000)
> -#define CONFIG_NR_DRAM_BANKS_MAX	2
> -
> -#else
> -#error "Unsupported SoC Platform..."
> -#endif
>
>   /*
>    * Custom CONFIG_SYS_TEXT_BASE can be done in<board>.h
> @@ -138,31 +90,6 @@
>   		+sizeof(CONFIG_SYS_PROMPT) + 16)	/* Print Buff */
>
>   /*
> - * NAND configuration
> - */
> -#ifdef CONFIG_CMD_NAND
> -#define CONFIG_NAND_KIRKWOOD
> -#define CONFIG_SYS_MAX_NAND_DEVICE	1
> -#define NAND_MAX_CHIPS			1
> -#define CONFIG_SYS_NAND_BASE		0xD8000000	/* MV_DEFADR_NANDF */
> -#define NAND_ALLOW_ERASE_ALL		1
> -#define CONFIG_SYS_64BIT_VSPRINTF	/* needed for nand_util.c */
> -#endif
> -
> -/*
> - * SPI Flash configuration
> - */
> -#ifdef CONFIG_CMD_SF
> -#define CONFIG_SPI_FLASH		1
> -#define CONFIG_HARD_SPI			1
> -#define CONFIG_KIRKWOOD_SPI		1
> -#define CONFIG_SPI_FLASH_MACRONIX	1
> -#define CONFIG_ENV_SPI_BUS		0
> -#define CONFIG_ENV_SPI_CS		0
> -#define CONFIG_ENV_SPI_MAX_HZ		50000000	/*50Mhz */
> -#endif
> -
> -/*
>    * Size of malloc() pool
>    */
>   #define CONFIG_SYS_MALLOC_LEN	(1024 * 1024) /* 1MiB for malloc() */
> @@ -176,9 +103,7 @@
>   #define CONFIG_CMDLINE_EDITING
>   #define CONFIG_CONSOLE_INFO_QUIET	/* some code reduction */
>   #define CONFIG_ARCH_CPU_INIT	/* call arch_cpu_init() */
> -#ifndef CONFIG_ARMADA100	/* will be removed latter */
>   #define CONFIG_ARCH_MISC_INIT	/* call arch_misc_init() */
> -#endif /* CONFIG_ARMADA100 */
>   #define CONFIG_BOARD_EARLY_INIT_F /* call board_init_f for early inits */
>   #define CONFIG_DISPLAY_CPUINFO	/* Display cpu info */
>   #define CONFIG_STACKSIZE	0x00100000	/* regular stack- 1M */
> @@ -199,27 +124,32 @@
>   #endif
>   #endif /* CONFIG_NR_DRAM_BANKS */
>
> +/* ====>  Include platform Common Definations */
> +#include<asm/arch/config.h>
> +
> +/* ====>  Include driver Common Definations */
>   /*
> - * Ethernet Driver configuration
> + * Common NAND configuration
>    */
> -#ifdef CONFIG_CMD_NET
> -#define CONFIG_CMD_MII
> -#define CONFIG_NETCONSOLE	/* include NetConsole support   */
> -#define CONFIG_NET_MULTI	/* specify more that one ports available */
> -#define CONFIG_MII		/* expose smi ove miiphy interface */
> -#define CONFIG_MVGBE		/* Enable Marvell Gbe Controller Driver */
> -#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN	/* detect link using phy */
> -#define CONFIG_ENV_OVERWRITE	/* ethaddr can be reprogrammed */
> -#define CONFIG_RESET_PHY_R	/* use reset_phy() to init mv8831116 PHY */
> -#endif /* CONFIG_CMD_NET */
> +#ifdef CONFIG_CMD_NAND
> +#define CONFIG_SYS_MAX_NAND_DEVICE     1
> +#define NAND_MAX_CHIPS                 1
> +#define CONFIG_SYS_64BIT_VSPRINTF      /* needed for nand_util.c */
> +#endif
> +
> +/*
> + * Common SPI Flash configuration
> + */
> +#ifdef CONFIG_CMD_SF
> +#define CONFIG_SPI_FLASH		1
> +#define CONFIG_SPI_FLASH_MACRONIX	1
> +#endif
>
>   /*
> - * USB/EHCI
> + * Common USB/EHCI configuration
>    */
>   #ifdef CONFIG_CMD_USB
>   #define CONFIG_USB_EHCI		/* Enable EHCI USB support */
> -#define CONFIG_USB_EHCI_KIRKWOOD
> -#define CONFIG_EHCI_IS_TDI
>   #define CONFIG_USB_STORAGE
>   #define CONFIG_DOS_PARTITION
>   #define CONFIG_ISO_PARTITION
> @@ -227,44 +157,9 @@
>   #endif /* CONFIG_CMD_USB */
>
>   /*
> - * IDE Support on SATA ports
> - */
> -#ifdef CONFIG_CMD_IDE
> -#define __io
> -#define CONFIG_CMD_EXT2
> -#define CONFIG_MVSATA_IDE
> -#define CONFIG_IDE_PREINIT
> -#define CONFIG_MVSATA_IDE_USE_PORT1
> -/* Needs byte-swapping for ATA data register */
> -#define CONFIG_IDE_SWAP_IO
> -/* Data, registers and alternate blocks are at the same offset */
> -#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
> -#define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
> -#define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
> -/* Each 8-bit ATA register is aligned to a 4-bytes address */
> -#define CONFIG_SYS_ATA_STRIDE		4
> -/* Controller supports 48-bits LBA addressing */
> -#define CONFIG_LBA48
> -/* CONFIG_CMD_IDE requires some #defines for ATA registers */
> -#define CONFIG_SYS_IDE_MAXBUS		2
> -#define CONFIG_SYS_IDE_MAXDEVICE	2
> -/* ATA registers base is at SATA controller base */
> -#define CONFIG_SYS_ATA_BASE_ADDR	MV_SATA_BASE
> -#endif /* CONFIG_CMD_IDE */
> -
> -/*
> - * I2C related stuff
> - */
> -#ifdef CONFIG_CMD_I2C
> -#define CONFIG_I2C_MVTWSI
> -#define CONFIG_SYS_I2C_SLAVE		0x0
> -#define CONFIG_SYS_I2C_SPEED		100000
> -#endif
> -
> -/*
>    * File system
>    */
> -#ifndef CONFIG_ARMADA100	/* will be removed latter */
> +#ifdef CONFIG_SYS_MVFS
>   #define CONFIG_CMD_EXT2
>   #define CONFIG_CMD_JFFS2
>   #define CONFIG_CMD_FAT
> @@ -275,6 +170,6 @@
>   #define CONFIG_MTD_PARTITIONS
>   #define CONFIG_CMD_MTDPARTS
>   #define CONFIG_LZO
> -#endif /* CONFIG_ARMADA100 */
> +#endif
>
>   #endif /* _MV_COMMON_H */

Amicalement,
-- 
Albert.

^ permalink raw reply	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V7 1/5] mv: seperate kirkwood and armada from common setting
  2011-01-27 18:34   ` Albert ARIBAUD
@ 2011-01-28  1:28     ` Lei Wen
  2011-01-28  6:47       ` Albert ARIBAUD
  0 siblings, 1 reply; 26+ messages in thread
From: Lei Wen @ 2011-01-28  1:28 UTC (permalink / raw)
  To: u-boot

Hi Albert,

On Fri, Jan 28, 2011 at 2:34 AM, Albert ARIBAUD <albert.aribaud@free.fr> wrote:
> Hi Lei Wen,
>
> Le 26/01/2011 11:31, Lei Wen a ?crit :
>
>> diff --git a/README b/README
>> index 755d17c..e0341b5 100644
>> --- a/README
>> +++ b/README
>> @@ -319,6 +319,11 @@ The following options need to be configured:
>> ? ? ? ? ? ? ? ? ? ? ? CONFIG_SYS_PQ2FADS ? ? ?- PQ2FADS-ZU or PQ2FADS-VR
>> ? ? ? ? ? ? ? ? ? ? ? CONFIG_SYS_8272ADS ? ? ?- MPC8272ADS
>>
>> +- Marvell Family Member
>> + ? ? ? ? ? ? CONFIG_SYS_MVFS ? ? ? ? - define it if you want to enable
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? multiply fs option at one time
>
> Are you sure about this "multiply"?

Should be multiple...
>
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? for marvell soc family
>> +
>> ? - MPC824X Family Member (if CONFIG_MPC824X is defined)
>> ? ? ? ? ? ? ? Define exactly one of
>> ? ? ? ? ? ? ? CONFIG_MPC8240, CONFIG_MPC8245
>> diff --git a/arch/arm/include/asm/arch-armada100/config.h b/arch/arm/include/asm/arch-armada100/config.h
>> new file mode 100644
>> index 0000000..f16806e
>> --- /dev/null
>> +++ b/arch/arm/include/asm/arch-armada100/config.h
>> @@ -0,0 +1,44 @@
>> +/*
>> + * (C) Copyright 2010
>
> Maybe update the copyright year?
My fault...

>
>> + * Marvell Semiconductor<www.marvell.com>
>> + * Written-by: Lei Wen<leiwen@marvell.com>
>> + *
>> + * See file CREDITS for list of people who contributed to this
>> + * project.
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of
>> + * the License, or (at your option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + *
>> + * You should have received a copy of the GNU General Public License
>> + * along with this program; if not, write to the Free Software
>> + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
>> + * MA 02110-1301 USA
>> + */
>> +
>> +/*
>> + * This file should be included in board config header file.
>> + *
>> + * It supports common definitions for Armada100 platform
>> + */
>> +
>> +#ifndef _ARMD1_CONFIG_H
>> +#define _ARMD1_CONFIG_H
>> +
>> +#define CONFIG_ARM926EJS ? ? 1 ? ? ? /* Basic Architecture */
>> +
>> +#define CONFIG_SYS_TCLK ? ? ? ? ? ? ?(14745600) ? ? ?/* NS16550 clk config */
>> +#define CONFIG_SYS_HZ_CLOCK ?(3250000) ? ? ? /* Timer Freq. 3.25MHZ */
>> +#define CONFIG_MARVELL_MFP ? ? ? ? ? ? ? ? ? /* Enable mvmfp driver */
>> +#define MV_MFPR_BASE ? ? ? ? ARMD1_MFPR_BASE
>> +#define MV_UART_CONSOLE_BASE ARMD1_UART1_BASE
>> +#define CONFIG_SYS_NS16550_IER ? ? ? (1<< ?6) ? ? ? ?/* Bit 6 in UART_IER register
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? represents UART Unit Enable */
>> +
>> +#endif /* _ARMD1_CONFIG_H */
>> diff --git a/arch/arm/include/asm/arch-kirkwood/config.h b/arch/arm/include/asm/arch-kirkwood/config.h
>> new file mode 100644
>> index 0000000..7c6d63b
>> --- /dev/null
>> +++ b/arch/arm/include/asm/arch-kirkwood/config.h
>> @@ -0,0 +1,145 @@
>> +/*
>> + * (C) Copyright 2010
>
> Ditto
>
>> + * Marvell Semiconductor<www.marvell.com>
>> + * Written-by: Lei Wen<leiwen@marvell.com>
>> + *
>> + * See file CREDITS for list of people who contributed to this
>> + * project.
>> + *
>> + * This program is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of
>> + * the License, or (at your option) any later version.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + *
>> + * You should have received a copy of the GNU General Public License
>> + * along with this program; if not, write to the Free Software
>> + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
>> + * MA 02110-1301 USA
>> + */
>> +
>> +/*
>> + * This file should be included in board config header file.
>> + *
>> + * It supports common definitions for Kirkwood platform
>> + */
>> +
>> +#ifndef _KW_CONFIG_H
>> +#define _KW_CONFIG_H
>> +
>> +#if defined (CONFIG_KW88F6281)
>> +#include<asm/arch/kw88f6281.h>
>> +#elif defined (CONFIG_KW88F6192)
>> +#include<asm/arch/kw88f6192.h>
>> +#else
>> +#error "SOC Name not defined"
>> +#endif /* CONFIG_KW88F6281 */
>> +
>> +#define CONFIG_ARM926EJS ? ? 1 ? ? ? /* Basic Architecture */
>> +
>> +#define CONFIG_MD5 ? /* get_random_hex on krikwood needs MD5 support */
>> +#define CONFIG_KIRKWOOD_EGIGA_INIT ? /* Enable GbePort0/1 for kernel */
>> +#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 ? ? ? ?/* Set RGMII Pad voltage to 1.8V */
>> +#define CONFIG_KIRKWOOD_PCIE_INIT ? ? ? /* Enable PCIE Port0 for kernel */
>> +
>> +/*
>> + * By default kwbimage.cfg from board specific folder is used
>> + * If for some board, different configuration file need to be used,
>> + * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
>> + */
>> +#ifndef CONFIG_SYS_KWD_CONFIG
>> +#define ? ? ?CONFIG_SYS_KWD_CONFIG ? $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage.cfg
>
> What are the '$()' operators doing here ?

This definition is served as generating kirkwood special image, which
I just move it from mv-common.h
$(obj)u-boot.kwb:       $(obj)u-boot.bin
                $(obj)tools/mkimage -n $(CONFIG_SYS_KWD_CONFIG) -T kwbimage \
                -a $(CONFIG_SYS_TEXT_BASE) -e $(CONFIG_SYS_TEXT_BASE) -d $< $@


Best regards,
Lei

^ permalink raw reply	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V7 1/5] mv: seperate kirkwood and armada from common setting
  2011-01-28  1:28     ` Lei Wen
@ 2011-01-28  6:47       ` Albert ARIBAUD
  2011-01-28  6:59         ` Lei Wen
  2011-01-28  8:17         ` Wolfgang Denk
  0 siblings, 2 replies; 26+ messages in thread
From: Albert ARIBAUD @ 2011-01-28  6:47 UTC (permalink / raw)
  To: u-boot

Hi Lei,

Le 28/01/2011 02:28, Lei Wen a ?crit :

>>> diff --git a/arch/arm/include/asm/arch-kirkwood/config.h b/arch/arm/include/asm/arch-kirkwood/config.h
>>> new file mode 100644
>>> index 0000000..7c6d63b
>>> --- /dev/null
>>> +++ b/arch/arm/include/asm/arch-kirkwood/config.h
>>> @@ -0,0 +1,145 @@

...

>>> +#ifndef CONFIG_SYS_KWD_CONFIG
>>> +#define      CONFIG_SYS_KWD_CONFIG   $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage.cfg
>>
>> What are the '$()' operators doing here ?
>
> This definition is served as generating kirkwood special image, which
> I just move it from mv-common.h
> $(obj)u-boot.kwb:       $(obj)u-boot.bin
>                  $(obj)tools/mkimage -n $(CONFIG_SYS_KWD_CONFIG) -T kwbimage \
>                  -a $(CONFIG_SYS_TEXT_BASE) -e $(CONFIG_SYS_TEXT_BASE) -d $<  $@

What I would like to understand is, the '$(X)' macro expansion operator 
indeed has meaning and makes sense for some tools such as Make, but not 
for a C preprocessor or compiler. Is this  config.h file included by a 
makefile somehow?

> Best regards,
> Lei

Amicalement,
-- 
Albert.

^ permalink raw reply	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V7 1/5] mv: seperate kirkwood and armada from common setting
  2011-01-28  6:47       ` Albert ARIBAUD
@ 2011-01-28  6:59         ` Lei Wen
  2011-01-28  7:27           ` Albert ARIBAUD
  2011-01-28  8:17         ` Wolfgang Denk
  1 sibling, 1 reply; 26+ messages in thread
From: Lei Wen @ 2011-01-28  6:59 UTC (permalink / raw)
  To: u-boot

Hi Albert,

On Fri, Jan 28, 2011 at 2:47 PM, Albert ARIBAUD <albert.aribaud@free.fr> wrote:
> Hi Lei,
>
> Le 28/01/2011 02:28, Lei Wen a ?crit :
>
>>>> diff --git a/arch/arm/include/asm/arch-kirkwood/config.h
>>>> b/arch/arm/include/asm/arch-kirkwood/config.h
>>>> new file mode 100644
>>>> index 0000000..7c6d63b
>>>> --- /dev/null
>>>> +++ b/arch/arm/include/asm/arch-kirkwood/config.h
>>>> @@ -0,0 +1,145 @@
>
> ...
>
>>>> +#ifndef CONFIG_SYS_KWD_CONFIG
>>>> +#define ? ? ?CONFIG_SYS_KWD_CONFIG
>>>> $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage.cfg
>>>
>>> What are the '$()' operators doing here ?
>>
>> This definition is served as generating kirkwood special image, which
>> I just move it from mv-common.h
>> $(obj)u-boot.kwb: ? ? ? $(obj)u-boot.bin
>> ? ? ? ? ? ? ? ? $(obj)tools/mkimage -n $(CONFIG_SYS_KWD_CONFIG) -T
>> kwbimage \
>> ? ? ? ? ? ? ? ? -a $(CONFIG_SYS_TEXT_BASE) -e $(CONFIG_SYS_TEXT_BASE) -d
>> $< ?$@
>
> What I would like to understand is, the '$(X)' macro expansion operator
> indeed has meaning and makes sense for some tools such as Make, but not for
> a C preprocessor or compiler. Is this ?config.h file included by a makefile
> somehow?
>

Yes, it would be included by the makefile as below:
Makefile: line 471:
$(obj)include/autoconf.mk: $(obj)include/config.h

Take guruplug as example.
Its guruplug.h would be include in the include/config.h.
While guruplug would involve the mv-common.h, in which the
arch/arm/include/asm/arch-kirkwood/config.h would be included.

I know this maybe a little complicated, but that is what it works.

Best regards,
Lei

^ permalink raw reply	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V7 1/5] mv: seperate kirkwood and armada from common setting
  2011-01-28  6:59         ` Lei Wen
@ 2011-01-28  7:27           ` Albert ARIBAUD
  0 siblings, 0 replies; 26+ messages in thread
From: Albert ARIBAUD @ 2011-01-28  7:27 UTC (permalink / raw)
  To: u-boot

Le 28/01/2011 07:59, Lei Wen a ?crit :
> Hi Albert,
>
> On Fri, Jan 28, 2011 at 2:47 PM, Albert ARIBAUD<albert.aribaud@free.fr>  wrote:
>> Hi Lei,
>>
>> Le 28/01/2011 02:28, Lei Wen a ?crit :
>>
>>>>> diff --git a/arch/arm/include/asm/arch-kirkwood/config.h
>>>>> b/arch/arm/include/asm/arch-kirkwood/config.h
>>>>> new file mode 100644
>>>>> index 0000000..7c6d63b
>>>>> --- /dev/null
>>>>> +++ b/arch/arm/include/asm/arch-kirkwood/config.h
>>>>> @@ -0,0 +1,145 @@
>>
>> ...
>>
>>>>> +#ifndef CONFIG_SYS_KWD_CONFIG
>>>>> +#define      CONFIG_SYS_KWD_CONFIG
>>>>> $(SRCTREE)/$(CONFIG_BOARDDIR)/kwbimage.cfg
>>>>
>>>> What are the '$()' operators doing here ?
>>>
>>> This definition is served as generating kirkwood special image, which
>>> I just move it from mv-common.h
>>> $(obj)u-boot.kwb:       $(obj)u-boot.bin
>>>                  $(obj)tools/mkimage -n $(CONFIG_SYS_KWD_CONFIG) -T
>>> kwbimage \
>>>                  -a $(CONFIG_SYS_TEXT_BASE) -e $(CONFIG_SYS_TEXT_BASE) -d
>>> $<    $@
>>
>> What I would like to understand is, the '$(X)' macro expansion operator
>> indeed has meaning and makes sense for some tools such as Make, but not for
>> a C preprocessor or compiler. Is this  config.h file included by a makefile
>> somehow?
>>
>
> Yes, it would be included by the makefile as below:
> Makefile: line 471:
> $(obj)include/autoconf.mk: $(obj)include/config.h
>
> Take guruplug as example.
> Its guruplug.h would be include in the include/config.h.
> While guruplug would involve the mv-common.h, in which the
> arch/arm/include/asm/arch-kirkwood/config.h would be included.

Understood. Maybe a comment right before the surprising '$()' line 
indicating why they're here would avoid other people wondering as I did.

> I know this maybe a little complicated, but that is what it works.

So be it. :)

> Best regards,
> Lei

Amicalement,
-- 
Albert.

^ permalink raw reply	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V7 1/5] mv: seperate kirkwood and armada from common setting
  2011-01-28  6:47       ` Albert ARIBAUD
  2011-01-28  6:59         ` Lei Wen
@ 2011-01-28  8:17         ` Wolfgang Denk
  1 sibling, 0 replies; 26+ messages in thread
From: Wolfgang Denk @ 2011-01-28  8:17 UTC (permalink / raw)
  To: u-boot

Dear Albert ARIBAUD,

In message <4D426699.4080106@free.fr> you wrote:
> What I would like to understand is, the '$(X)' macro expansion operator
> indeed has meaning and makes sense for some tools such as Make, but not
> for a C preprocessor or compiler. Is this  config.h file included by a
> makefile somehow?

yes, it is.

Please see the autoconf.mk build step in the top level makefile: it
processes (among other things) the board config file and creates
include files to provide the needed symbols for make.

It is this mechanism that allows us - for example - to move the
CONFIG_SYS_TEXT_BASE definitions into the board config files, even
though these are needed in the Makefiles for the linker step.

Best regards,

Wolfgang Denk

-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
When a woman marries again it is because she detested her first  hus-
band.  When  a  man  marries again, it is because he adored his first
wife.                                                  -- Oscar Wilde

^ permalink raw reply	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V7 2/5] ARM: Add Support for Marvell Pantheon Familiy SoCs
  2011-01-25  2:40 [U-Boot] [PATCH V6 0/5] Add Pantheon soc and dkb board support Lei Wen
                   ` (6 preceding siblings ...)
  2011-01-26 10:31 ` [U-Boot] [PATCH V7 1/5] mv: seperate kirkwood and armada from common setting Lei Wen
@ 2011-01-26 10:31 ` Lei Wen
  2011-01-26 10:31 ` [U-Boot] [PATCH V7 3/5] serial: add pantheon soc support Lei Wen
                   ` (2 subsequent siblings)
  10 siblings, 0 replies; 26+ messages in thread
From: Lei Wen @ 2011-01-26 10:31 UTC (permalink / raw)
  To: u-boot

Pantheon Family processors are highly integrated SoCs
based on Sheeva_88SV331x-v5 PJ1 cpu core.
Ref:
http://www.marvell.com/products/processors/communications/marvell_pantheon_910_920_pb.pdf

SoC versions Supported:
1) PANTHEON920          (TD)
2) PANTHEON910          (TTC)

Signed-off-by: Lei Wen <leiwen@marvell.com>
---
V2:

V3:
Fix copyright claim year.

V4:
Add change log to each patch.

V5:
coding style fix.

V6:
Rebase patch on latest u-boot-marvell.git.

V7:
Fix timer read to avoid potential optimization out of loop.

 arch/arm/cpu/arm926ejs/pantheon/Makefile      |   46 ++++++
 arch/arm/cpu/arm926ejs/pantheon/cpu.c         |   78 +++++++++
 arch/arm/cpu/arm926ejs/pantheon/dram.c        |  132 +++++++++++++++
 arch/arm/cpu/arm926ejs/pantheon/timer.c       |  214 +++++++++++++++++++++++++
 arch/arm/include/asm/arch-pantheon/config.h   |   38 +++++
 arch/arm/include/asm/arch-pantheon/cpu.h      |   79 +++++++++
 arch/arm/include/asm/arch-pantheon/pantheon.h |   54 ++++++
 7 files changed, 641 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/Makefile
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/cpu.c
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/dram.c
 create mode 100644 arch/arm/cpu/arm926ejs/pantheon/timer.c
 create mode 100644 arch/arm/include/asm/arch-pantheon/config.h
 create mode 100644 arch/arm/include/asm/arch-pantheon/cpu.h
 create mode 100644 arch/arm/include/asm/arch-pantheon/pantheon.h

diff --git a/arch/arm/cpu/arm926ejs/pantheon/Makefile b/arch/arm/cpu/arm926ejs/pantheon/Makefile
new file mode 100644
index 0000000..73644c7
--- /dev/null
+++ b/arch/arm/cpu/arm926ejs/pantheon/Makefile
@@ -0,0 +1,46 @@
+#
+# (C) Copyright 2010
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Lei Wen <leiwen@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(SOC).o
+
+COBJS-y	= cpu.o timer.o dram.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS-y))
+
+all:	$(obj).depend $(LIB)
+
+$(LIB):	$(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/arch/arm/cpu/arm926ejs/pantheon/cpu.c b/arch/arm/cpu/arm926ejs/pantheon/cpu.c
new file mode 100644
index 0000000..fd006af
--- /dev/null
+++ b/arch/arm/cpu/arm926ejs/pantheon/cpu.c
@@ -0,0 +1,78 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <asm/arch/pantheon.h>
+#include <asm/io.h>
+
+#define UARTCLK14745KHZ	(APBC_APBCLK | APBC_FNCLK | APBC_FNCLKSEL(1))
+#define SET_MRVL_ID	(1<<8)
+#define L2C_RAM_SEL	(1<<4)
+
+int arch_cpu_init(void)
+{
+	u32 val;
+	struct panthcpu_registers *cpuregs =
+		(struct panthcpu_registers*) PANTHEON_CPU_BASE;
+
+	struct panthapb_registers *apbclkres =
+		(struct panthapb_registers*) PANTHEON_APBC_BASE;
+
+	struct panthmpmu_registers *mpmu =
+		(struct panthmpmu_registers*) PANTHEON_MPMU_BASE;
+
+	/* set SEL_MRVL_ID bit in PANTHEON_CPU_CONF register */
+	val = readl(&cpuregs->cpu_conf);
+	val = val | SET_MRVL_ID;
+	writel(val, &cpuregs->cpu_conf);
+
+	/* Turn on clock gating (PMUM_CCGR) */
+	writel(0xFFFFFFFF, &mpmu->ccgr);
+
+	/* Turn on clock gating (PMUM_ACGR) */
+	writel(0xFFFFFFFF, &mpmu->acgr);
+
+	/* Turn on uart2 clock */
+	writel(UARTCLK14745KHZ, &apbclkres->uart0);
+
+	/* Enable GPIO clock */
+	writel(APBC_APBCLK, &apbclkres->gpio);
+
+	icache_enable();
+
+	return 0;
+}
+
+#if defined(CONFIG_DISPLAY_CPUINFO)
+int print_cpuinfo(void)
+{
+	u32 id;
+	struct panthcpu_registers *cpuregs =
+		(struct panthcpu_registers*) PANTHEON_CPU_BASE;
+
+	id = readl(&cpuregs->chip_id);
+	printf("SoC:   PANTHEON 88AP%X-%X\n", (id & 0xFFF), (id >> 0x10));
+	return 0;
+}
+#endif
diff --git a/arch/arm/cpu/arm926ejs/pantheon/dram.c b/arch/arm/cpu/arm926ejs/pantheon/dram.c
new file mode 100644
index 0000000..2d8709f
--- /dev/null
+++ b/arch/arm/cpu/arm926ejs/pantheon/dram.c
@@ -0,0 +1,132 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>,
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <asm/arch/pantheon.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Pantheon DRAM controller supports upto 8 banks
+ * for chip select 0 and 1
+ */
+
+/*
+ * DDR Memory Control Registers
+ * Refer Datasheet 4.4
+ */
+struct panthddr_map_registers {
+	u32	cs;	/* Memory Address Map Register -CS */
+	u32	pad[3];
+};
+
+struct panthddr_registers {
+	u8	pad[0x100 - 0x000];
+	struct panthddr_map_registers mmap[2];
+};
+
+/*
+ * panth_sdram_base - reads SDRAM Base Address Register
+ */
+u32 panth_sdram_base(int chip_sel)
+{
+	struct panthddr_registers *ddr_regs =
+		(struct panthddr_registers *)PANTHEON_DRAM_BASE;
+	u32 result = 0;
+	u32 CS_valid = 0x01 & readl(&ddr_regs->mmap[chip_sel].cs);
+
+	if (!CS_valid)
+		return 0;
+
+	result = readl(&ddr_regs->mmap[chip_sel].cs) & 0xFF800000;
+	return result;
+}
+
+/*
+ * panth_sdram_size - reads SDRAM size
+ */
+u32 panth_sdram_size(int chip_sel)
+{
+	struct panthddr_registers *ddr_regs =
+		(struct panthddr_registers *)PANTHEON_DRAM_BASE;
+	u32 result = 0;
+	u32 CS_valid = 0x01 & readl(&ddr_regs->mmap[chip_sel].cs);
+
+	if (!CS_valid)
+		return 0;
+
+	result = readl(&ddr_regs->mmap[chip_sel].cs);
+	result = (result >> 16) & 0xF;
+	if (result < 0x7) {
+		printf("Unknown DRAM Size\n");
+		return -1;
+	} else {
+		return ((0x8 << (result - 0x7)) * 1024 * 1024);
+	}
+}
+
+#ifndef CONFIG_SYS_BOARD_DRAM_INIT
+int dram_init(void)
+{
+	int i;
+
+	gd->ram_size = 0;
+	for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+		gd->bd->bi_dram[i].start = panth_sdram_base(i);
+		gd->bd->bi_dram[i].size = panth_sdram_size(i);
+		/*
+		 * It is assumed that all memory banks are consecutive
+		 * and without gaps.
+		 * If the gap is found, ram_size will be reported for
+		 * consecutive memory only
+		 */
+		if (gd->bd->bi_dram[i].start != gd->ram_size)
+			break;
+
+		gd->ram_size += gd->bd->bi_dram[i].size;
+
+	}
+
+	for (; i < CONFIG_NR_DRAM_BANKS; i++) {
+		/*
+		 * If above loop terminated prematurely, we need to set
+		 * remaining banks' start address & size as 0. Otherwise other
+		 * u-boot functions and Linux kernel gets wrong values which
+		 * could result in crash
+		 */
+		gd->bd->bi_dram[i].start = 0;
+		gd->bd->bi_dram[i].size = 0;
+	}
+	return 0;
+}
+
+/*
+ * If this function is not defined here,
+ * board.c alters dram bank zero configuration defined above.
+ */
+void dram_init_banksize(void)
+{
+	dram_init();
+}
+#endif /* CONFIG_SYS_BOARD_DRAM_INIT */
diff --git a/arch/arm/cpu/arm926ejs/pantheon/timer.c b/arch/arm/cpu/arm926ejs/pantheon/timer.c
new file mode 100644
index 0000000..8647c22
--- /dev/null
+++ b/arch/arm/cpu/arm926ejs/pantheon/timer.c
@@ -0,0 +1,214 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <asm/arch/pantheon.h>
+
+/*
+ * Timer registers
+ * Refer 6.2.9 in Datasheet
+ */
+struct panthtmr_registers {
+	u32 clk_ctrl;	/* Timer clk control reg */
+	u32 match[9];	/* Timer match registers */
+	u32 count[3];	/* Timer count registers */
+	u32 status[3];
+	u32 ie[3];
+	u32 preload[3];	/* Timer preload value */
+	u32 preload_ctrl[3];
+	u32 wdt_match_en;
+	u32 wdt_match_r;
+	u32 wdt_val;
+	u32 wdt_sts;
+	u32 icr[3];
+	u32 wdt_icr;
+	u32 cer;	/* Timer count enable reg */
+	u32 cmr;
+	u32 ilr[3];
+	u32 wcr;
+	u32 wfar;
+	u32 wsar;
+	u32 cvwr[3];
+};
+
+#define TIMER			0	/* Use TIMER 0 */
+/* Each timer has 3 match registers */
+#define MATCH_CMP(x)		((3 * TIMER) + x)
+#define TIMER_LOAD_VAL 		0xffffffff
+#define	COUNT_RD_REQ		0x1
+
+DECLARE_GLOBAL_DATA_PTR;
+/* Using gd->tbu from timestamp and gd->tbl for lastdec */
+
+/*
+ * For preventing risk of instability in reading counter value,
+ * first set read request to register cvwr and then read same
+ * register after it captures counter value.
+ */
+ulong read_timer(void)
+{
+	struct panthtmr_registers *panthtimers =
+		(struct panthtmr_registers *) PANTHEON_TIMER_BASE;
+	volatile int loop=100;
+	ulong val;
+
+	writel(COUNT_RD_REQ, &panthtimers->cvwr);
+	while (loop--)
+		val = readl(&panthtimers->cvwr);
+
+	/*
+	 * This stop gcc complain and prevent loop mistake init to 0
+	 */
+	val = readl(&panthtimers->cvwr);
+
+	return val;
+}
+
+void reset_timer_masked(void)
+{
+	/* reset time */
+	gd->tbl = read_timer();
+	gd->tbu = 0;
+}
+
+ulong get_timer_masked(void)
+{
+	ulong now = read_timer();
+
+	if (now >= gd->tbl) {
+		/* normal mode */
+		gd->tbu += now - gd->tbl;
+	} else {
+		/* we have an overflow ... */
+		gd->tbu += now + TIMER_LOAD_VAL - gd->tbl;
+	}
+	gd->tbl = now;
+
+	return gd->tbu;
+}
+
+void reset_timer(void)
+{
+	reset_timer_masked();
+}
+
+ulong get_timer(ulong base)
+{
+	return ((get_timer_masked() / (CONFIG_SYS_HZ_CLOCK / 1000)) -
+		base);
+}
+
+void set_timer(ulong t)
+{
+	gd->tbu = t;
+}
+
+void __udelay(unsigned long usec)
+{
+	ulong delayticks;
+	ulong endtime;
+
+	delayticks = (usec * (CONFIG_SYS_HZ_CLOCK / 1000000));
+	endtime = get_timer_masked() + delayticks;
+
+	while (get_timer_masked() < endtime)
+		;
+}
+
+/*
+ * init the Timer
+ */
+int timer_init(void)
+{
+	struct panthapb_registers *apb1clkres =
+		(struct panthapb_registers *) PANTHEON_APBC_BASE;
+	struct panthtmr_registers *panthtimers =
+		(struct panthtmr_registers *) PANTHEON_TIMER_BASE;
+
+	/* Enable Timer clock@3.25 MHZ */
+	writel(APBC_APBCLK | APBC_FNCLK | APBC_FNCLKSEL(3), &apb1clkres->timers);
+
+	/* load value into timer */
+	writel(0x0, &panthtimers->clk_ctrl);
+	/* Use Timer 0 Match Resiger 0 */
+	writel(TIMER_LOAD_VAL, &panthtimers->match[MATCH_CMP(0)]);
+	/* Preload value is 0 */
+	writel(0x0, &panthtimers->preload[TIMER]);
+	/* Enable match comparator 0 for Timer 0 */
+	writel(0x1, &panthtimers->preload_ctrl[TIMER]);
+
+	/* Enable timer 0 */
+	writel(0x1, &panthtimers->cer);
+	/* init the gd->tbu and gd->tbl value */
+	reset_timer_masked();
+
+	return 0;
+}
+
+#define MPMU_APRR_WDTR	(1<<4)
+#define TMR_WFAR	0xbaba	/* WDT Register First key */
+#define TMP_WSAR	0xeb10	/* WDT Register Second key */
+
+/*
+ * This function uses internal Watchdog Timer
+ * based reset mechanism.
+ * Steps to write watchdog registers (protected access)
+ * 1. Write key value to TMR_WFAR reg.
+ * 2. Write key value to TMP_WSAR reg.
+ * 3. Perform write operation.
+ */
+void reset_cpu (unsigned long ignored)
+{
+	struct panthmpmu_registers *mpmu =
+		(struct panthmpmu_registers *) PANTHEON_MPMU_BASE;
+	struct panthtmr_registers *panthtimers =
+		(struct panthtmr_registers *) PANTHEON_WD_TIMER_BASE;
+	u32 val;
+
+	/* negate hardware reset to the WDT after system reset */
+	val = readl(&mpmu->aprr);
+	val = val | MPMU_APRR_WDTR;
+	writel(val, &mpmu->aprr);
+
+	/* reset/enable WDT clock */
+	writel(APBC_APBCLK, &mpmu->wdtpcr);
+
+	/* clear previous WDT status */
+	writel(TMR_WFAR, &panthtimers->wfar);
+	writel(TMP_WSAR, &panthtimers->wsar);
+	writel(0, &panthtimers->wdt_sts);
+
+	/* set match counter */
+	writel(TMR_WFAR, &panthtimers->wfar);
+	writel(TMP_WSAR, &panthtimers->wsar);
+	writel(0xf, &panthtimers->wdt_match_r);
+
+	/* enable WDT reset */
+	writel(TMR_WFAR, &panthtimers->wfar);
+	writel(TMP_WSAR, &panthtimers->wsar);
+	writel(0x3, &panthtimers->wdt_match_en);
+
+	/*enable functional WDT clock */
+	writel(APBC_APBCLK | APBC_FNCLK, &mpmu->wdtpcr);
+}
diff --git a/arch/arm/include/asm/arch-pantheon/config.h b/arch/arm/include/asm/arch-pantheon/config.h
new file mode 100644
index 0000000..9f5fe6a
--- /dev/null
+++ b/arch/arm/include/asm/arch-pantheon/config.h
@@ -0,0 +1,38 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _PANTHEON_CONFIG_H
+#define _PANTHEON_CONFIG_H
+
+#define CONFIG_ARM926EJS	1	/* Basic Architecture */
+
+#define CONFIG_SYS_TCLK		(14745600)	/* NS16550 clk config */
+#define CONFIG_SYS_HZ_CLOCK	(3250000)	/* Timer Freq. 3.25MHZ */
+#define CONFIG_MARVELL_MFP			/* Enable mvmfp driver */
+#define MV_MFPR_BASE		PANTHEON_MFPR_BASE
+#define MV_UART_CONSOLE_BASE	PANTHEON_UART1_BASE
+#define CONFIG_SYS_NS16550_IER	(1 << 6)	/* Bit 6 in UART_IER register
+						represents UART Unit Enable */
+
+#endif /* _PANTHEON_CONFIG_H */
diff --git a/arch/arm/include/asm/arch-pantheon/cpu.h b/arch/arm/include/asm/arch-pantheon/cpu.h
new file mode 100644
index 0000000..1f112c9
--- /dev/null
+++ b/arch/arm/include/asm/arch-pantheon/cpu.h
@@ -0,0 +1,79 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _PANTHEON_CPU_H
+#define _PANTHEON_CPU_H
+
+#include <asm/io.h>
+#include <asm/system.h>
+
+/*
+ * Main Power Management (MPMU) Registers
+ * Refer Register Datasheet 9.1
+ */
+struct panthmpmu_registers {
+	u8 pad0[0x0024];
+	u32 ccgr;	/*0x0024*/
+	u8 pad1[0x0200 - 0x024 - 4];
+	u32 wdtpcr;	/*0x0200*/
+	u8 pad2[0x1020 - 0x200 - 4];
+	u32 aprr;	/*0x1020*/
+	u32 acgr;	/*0x1024*/
+};
+
+/*
+ * APB Clock Reset/Control Registers
+ * Refer Register Datasheet 6.14
+ */
+struct panthapb_registers {
+	u32 uart0;	/*0x000*/
+	u32 uart1;	/*0x004*/
+	u32 gpio;	/*0x008*/
+	u8 pad0[0x034 - 0x08 - 4];
+	u32 timers;	/*0x034*/
+};
+
+/*
+ * CPU Interface Registers
+ * Refer Register Datasheet 4.3
+ */
+struct panthcpu_registers {
+	u32 chip_id;		/* Chip Id Reg */
+	u32 pad;
+	u32 cpu_conf;		/* CPU Conf Reg */
+	u32 pad1;
+	u32 cpu_sram_spd;	/* CPU SRAM Speed Reg */
+	u32 pad2;
+	u32 cpu_l2c_spd;	/* CPU L2cache Speed Conf */
+	u32 mcb_conf;		/* MCB Conf Reg */
+	u32 sys_boot_ctl;	/* Sytem Boot Control */
+};
+
+/*
+ * Functions
+ */
+u32 panth_sdram_base(int);
+u32 panth_sdram_size(int);
+
+#endif /* _PANTHEON_CPU_H */
diff --git a/arch/arm/include/asm/arch-pantheon/pantheon.h b/arch/arm/include/asm/arch-pantheon/pantheon.h
new file mode 100644
index 0000000..fb1b1b5
--- /dev/null
+++ b/arch/arm/include/asm/arch-pantheon/pantheon.h
@@ -0,0 +1,54 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _PANTHEON_H
+#define _PANTHEON_H
+
+#ifndef __ASSEMBLY__
+#include <asm/types.h>
+#include <asm/io.h>
+#endif	/* __ASSEMBLY__ */
+
+#include <asm/arch/cpu.h>
+
+/* Common APB clock register bit definitions */
+#define APBC_APBCLK     (1<<0)  /* APB Bus Clock Enable */
+#define APBC_FNCLK      (1<<1)  /* Functional Clock Enable */
+#define APBC_RST        (1<<2)  /* Reset Generation */
+/* Functional Clock Selection Mask */
+#define APBC_FNCLKSEL(x)        (((x) & 0xf) << 4)
+
+/* Register Base Addresses */
+#define PANTHEON_DRAM_BASE	0xB0000000
+#define PANTHEON_TIMER_BASE	0xD4014000
+#define PANTHEON_WD_TIMER_BASE	0xD4080000
+#define PANTHEON_APBC_BASE	0xD4015000
+#define PANTHEON_UART1_BASE	0xD4017000
+#define PANTHEON_UART2_BASE	0xD4018000
+#define PANTHEON_GPIO_BASE	0xD4019000
+#define PANTHEON_MFPR_BASE	0xD401E000
+#define PANTHEON_MPMU_BASE	0xD4050000
+#define PANTHEON_CPU_BASE	0xD4282C00
+
+#endif /* _PANTHEON_H */
-- 
1.7.0.4

^ permalink raw reply related	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V7 3/5] serial: add pantheon soc support
  2011-01-25  2:40 [U-Boot] [PATCH V6 0/5] Add Pantheon soc and dkb board support Lei Wen
                   ` (7 preceding siblings ...)
  2011-01-26 10:31 ` [U-Boot] [PATCH V7 2/5] ARM: Add Support for Marvell Pantheon Familiy SoCs Lei Wen
@ 2011-01-26 10:31 ` Lei Wen
  2011-01-26 10:31 ` [U-Boot] [PATCH V7 4/5] mvmfp: add MFP configuration support for PANTHEON Lei Wen
  2011-01-26 10:31 ` [U-Boot] [PATCH V7 5/5] Pantheon: Add Board Support for Marvell dkb board Lei Wen
  10 siblings, 0 replies; 26+ messages in thread
From: Lei Wen @ 2011-01-26 10:31 UTC (permalink / raw)
  To: u-boot

Signed-off-by: Lei Wen <leiwen@marvell.com>
---
V2:

V3:
Fix copyright claim year.

V4:
Add change log to each patch.

V5:

V6:
Rebase patch on latest u-boot-marvell.git.

V7:

 drivers/serial/serial.c |    2 ++
 1 files changed, 2 insertions(+), 0 deletions(-)

diff --git a/drivers/serial/serial.c b/drivers/serial/serial.c
index cd3439e..4032dfd 100644
--- a/drivers/serial/serial.c
+++ b/drivers/serial/serial.c
@@ -33,6 +33,8 @@
 #include <asm/arch/orion5x.h>
 #elif defined(CONFIG_ARMADA100)
 #include <asm/arch/armada100.h>
+#elif defined(CONFIG_PANTHEON)
+#include <asm/arch/pantheon.h>
 #endif
 
 #if defined (CONFIG_SERIAL_MULTI)
-- 
1.7.0.4

^ permalink raw reply related	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V7 4/5] mvmfp: add MFP configuration support for PANTHEON
  2011-01-25  2:40 [U-Boot] [PATCH V6 0/5] Add Pantheon soc and dkb board support Lei Wen
                   ` (8 preceding siblings ...)
  2011-01-26 10:31 ` [U-Boot] [PATCH V7 3/5] serial: add pantheon soc support Lei Wen
@ 2011-01-26 10:31 ` Lei Wen
  2011-01-26 10:31 ` [U-Boot] [PATCH V7 5/5] Pantheon: Add Board Support for Marvell dkb board Lei Wen
  10 siblings, 0 replies; 26+ messages in thread
From: Lei Wen @ 2011-01-26 10:31 UTC (permalink / raw)
  To: u-boot

This patch adds the Multiply Function Pin configuration support for
Marvell PANTHEON SoCs

Signed-off-by: Lei Wen <leiwen@marvell.com>
---
V2:

V3:
Fix copyright claim year.

V4:
Add change log to each patch.

V5:
coding style fix.

V6:
Rebase patch on latest u-boot-marvell.git.

V7:
Correct patch comments

 arch/arm/include/asm/arch-pantheon/mfp.h |   41 ++++++++++++++++++++++++++++++
 drivers/gpio/mvmfp.c                     |    2 +
 2 files changed, 43 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/include/asm/arch-pantheon/mfp.h

diff --git a/arch/arm/include/asm/arch-pantheon/mfp.h b/arch/arm/include/asm/arch-pantheon/mfp.h
new file mode 100644
index 0000000..ce3aca1
--- /dev/null
+++ b/arch/arm/include/asm/arch-pantheon/mfp.h
@@ -0,0 +1,41 @@
+/*
+ * Based on arch/arm/include/asm/arch-armada100/mfp.h
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __PANTHEON_MFP_H
+#define __PANTHEON_MFP_H
+
+/*
+ * Frequently used MFP Configuration macros for all PANTHEON family of SoCs
+ *
+ * offset, pull,pF, drv,dF, edge,eF ,afn,aF
+ */
+/* UART2 */
+#define MFP47_UART2_RXD		MFP_REG(0x198) | MFP_AF6 | MFP_DRIVE_MEDIUM
+#define MFP48_UART2_TXD		MFP_REG(0x19c) | MFP_AF6 | MFP_DRIVE_MEDIUM
+
+/* More macros can be defined here... */
+
+#define MFP_PIN_MAX	117
+#endif
diff --git a/drivers/gpio/mvmfp.c b/drivers/gpio/mvmfp.c
index 5646ed4..e7830c6 100644
--- a/drivers/gpio/mvmfp.c
+++ b/drivers/gpio/mvmfp.c
@@ -28,6 +28,8 @@
 #include <asm/arch/mfp.h>
 #ifdef CONFIG_ARMADA100
 #include <asm/arch/armada100.h>
+#elif defined(CONFIG_PANTHEON)
+#include <asm/arch/pantheon.h>
 #else
 #error Unsupported SoC...
 #endif
-- 
1.7.0.4

^ permalink raw reply related	[flat|nested] 26+ messages in thread

* [U-Boot] [PATCH V7 5/5] Pantheon: Add Board Support for Marvell dkb board
  2011-01-25  2:40 [U-Boot] [PATCH V6 0/5] Add Pantheon soc and dkb board support Lei Wen
                   ` (9 preceding siblings ...)
  2011-01-26 10:31 ` [U-Boot] [PATCH V7 4/5] mvmfp: add MFP configuration support for PANTHEON Lei Wen
@ 2011-01-26 10:31 ` Lei Wen
  10 siblings, 0 replies; 26+ messages in thread
From: Lei Wen @ 2011-01-26 10:31 UTC (permalink / raw)
  To: u-boot

DKB is a Development Board for PANTHEON TD/TTC(pxa920/pxa910) with
* Processor upto 806Mhz
* LPDDR1/2
* x8/x16 SLC/MLC NAND
* Footprints for eMMC & MMC x8 card

With Peripherals:
* Parallel LCD I/F
* Audio codecs (88PM8607)
* MIPI CSI-2 camera
* Marvell 88W8787 802.11n/BT module
* Marvell 2G/3G RF
* Dual analog mics & speakers, headset jack, LED, ambient
* USB2.0 HS host, OTG (mini AB)
* GPIO, GPIO expander with DIP switches for easier selection
* UART serial over USB, CIR

This patch adds basic board support with DRAM and UART functionality

Signed-off-by: Lei Wen <leiwen@marvell.com>
---
V2:

V3:
Fix copyright claim year.

V4:
Add change log to each patch.

V5:
Remove additional CONFIG_SYS_NS16550_COM1 definition in dkb.h

V6:
Rebase patch on latest u-boot-marvell.git.
And fix a build warning.

V7:

MAINTAINERS                |    4 +++
 board/Marvell/dkb/Makefile |   51 ++++++++++++++++++++++++++++++++++
 board/Marvell/dkb/dkb.c    |   54 ++++++++++++++++++++++++++++++++++++
 boards.cfg                 |    1 +
 include/configs/dkb.h      |   65 ++++++++++++++++++++++++++++++++++++++++++++
 5 files changed, 175 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/dkb/Makefile
 create mode 100644 board/Marvell/dkb/dkb.c
 create mode 100644 include/configs/dkb.h

diff --git a/MAINTAINERS b/MAINTAINERS
index d92ff8d..36e2516 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -850,6 +850,10 @@ Prafulla Wadaskar <prafulla@marvell.com>
 	rd6281a		ARM926EJS (Kirkwood SoC)
 	sheevaplug	ARM926EJS (Kirkwood SoC)
 
+Lei Wen <leiwen@marvell.com>
+
+	dkb		ARM926EJS (PANTHEON 88AP920 SOC)
+
 Matthias Weisser <weisserm@arcor.de>
 
 	jadecpu		ARM926EJS (MB86R01 SoC)
diff --git a/board/Marvell/dkb/Makefile b/board/Marvell/dkb/Makefile
new file mode 100644
index 0000000..8835f8e
--- /dev/null
+++ b/board/Marvell/dkb/Makefile
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2010
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Lei Wen <leiwen@marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB     = $(obj)lib$(BOARD).o
+
+COBJS	:= dkb.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(obj).depend $(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/Marvell/dkb/dkb.c b/board/Marvell/dkb/dkb.c
new file mode 100644
index 0000000..95a3982
--- /dev/null
+++ b/board/Marvell/dkb/dkb.c
@@ -0,0 +1,54 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <mvmfp.h>
+#include <asm/arch/mfp.h>
+#include <asm/arch/cpu.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+	u32 mfp_cfg[] = {
+		/* Enable Console on UART2 */
+		MFP47_UART2_RXD,
+		MFP48_UART2_TXD,
+
+		MFP_EOC		/*End of configureation*/
+	};
+	/* configure MFP's */
+	mfp_config(mfp_cfg);
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* arch number of Board */
+	gd->bd->bi_arch_number = MACH_TYPE_TTC_DKB;
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params = panth_sdram_base(0) + 0x100;
+	return 0;
+}
diff --git a/boards.cfg b/boards.cfg
index 350f287..7e1e283 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -104,6 +104,7 @@ imx27lite                    arm         arm926ejs   imx27lite           logicpd
 magnesium                    arm         arm926ejs   imx27lite           logicpd        mx27
 omap5912osk                  arm         arm926ejs   -                   ti             omap
 edminiv2                     arm         arm926ejs   -                   LaCie          orion5x
+dkb			     arm         arm926ejs   -                   Marvell        pantheon
 ca9x4_ct_vxp                 arm         armv7       vexpress            armltd
 mx51evk                      arm         armv7       mx51evk             freescale      mx5
 mx53evk                      arm         armv7       mx53evk             freescale      mx5
diff --git a/include/configs/dkb.h b/include/configs/dkb.h
new file mode 100644
index 0000000..f9104c4
--- /dev/null
+++ b/include/configs/dkb.h
@@ -0,0 +1,65 @@
+/*
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __CONFIG_DKB_H
+#define __CONFIG_DKB_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING	"\nMarvell-TTC DKB"
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_SHEEVA_88SV331xV5	1	/* CPU Core subversion */
+#define CONFIG_PANTHEON			1	/* SOC Family Name */
+#define CONFIG_MACH_TTC_DKB		1	/* Machine type */
+#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
+
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_TEXT_BASE - 0x00200000)
+#define CONFIG_NR_DRAM_BANKS_MAX	2
+
+/*
+ * Commands configuration
+ */
+#define CONFIG_SYS_NO_FLASH		/* Declare no flash (NOR/SPI) */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_AUTOSCRIPT
+#undef CONFIG_CMD_NET
+#undef CONFIG_CMD_NFS
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+#undef CONFIG_ARCH_MISC_INIT
+/*
+ * Environment variables configurations
+ */
+#define CONFIG_ENV_IS_NOWHERE	1	/* if env in SDRAM */
+#define CONFIG_ENV_SIZE	0x20000	/* 64k */
+
+#endif	/* __CONFIG_DKB_H */
-- 
1.7.0.4

^ permalink raw reply related	[flat|nested] 26+ messages in thread

end of thread, other threads:[~2011-02-09  9:47 UTC | newest]

Thread overview: 26+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2011-01-25  2:40 [U-Boot] [PATCH V6 0/5] Add Pantheon soc and dkb board support Lei Wen
2011-01-25  2:40 ` [U-Boot] [PATCH V6 1/5] mv: seperate kirkwood and armada from common setting Lei Wen
2011-01-25  2:40 ` [U-Boot] [PATCH V6 2/5] ARM: Add Support for Marvell Pantheon Familiy SoCs Lei Wen
2011-01-25  2:40 ` [U-Boot] [PATCH V6 3/5] serial: add pantheon soc support Lei Wen
2011-01-25  2:40 ` [U-Boot] [PATCH V6 4/5] mvmfp: add MFP configuration support for PANTHEON Lei Wen
2011-01-25  2:40 ` [U-Boot] [PATCH V6 5/5] Pantheon: Add Board Support for Marvell dkb board Lei Wen
2011-01-26 10:31 ` [U-Boot] [PATCH V7 0/5] Add Pantheon soc and dkb board support Lei Wen
2011-01-28  9:19   ` [U-Boot] [PATCH V8 " Lei Wen
2011-02-05  6:53     ` Albert ARIBAUD
2011-02-09  9:47     ` Prafulla Wadaskar
2011-01-28  9:19   ` [U-Boot] [PATCH V8 1/5] mv: seperate kirkwood and armada from common setting Lei Wen
2011-01-28  9:19   ` [U-Boot] [PATCH V8 2/5] ARM: Add Support for Marvell Pantheon Familiy SoCs Lei Wen
2011-01-28  9:19   ` [U-Boot] [PATCH V8 3/5] serial: add pantheon soc support Lei Wen
2011-01-28  9:19   ` [U-Boot] [PATCH V8 4/5] mvmfp: add MFP configuration support for PANTHEON Lei Wen
2011-01-28  9:19   ` [U-Boot] [PATCH V8 5/5] Pantheon: Add Board Support for Marvell dkb board Lei Wen
2011-01-26 10:31 ` [U-Boot] [PATCH V7 1/5] mv: seperate kirkwood and armada from common setting Lei Wen
2011-01-27 18:34   ` Albert ARIBAUD
2011-01-28  1:28     ` Lei Wen
2011-01-28  6:47       ` Albert ARIBAUD
2011-01-28  6:59         ` Lei Wen
2011-01-28  7:27           ` Albert ARIBAUD
2011-01-28  8:17         ` Wolfgang Denk
2011-01-26 10:31 ` [U-Boot] [PATCH V7 2/5] ARM: Add Support for Marvell Pantheon Familiy SoCs Lei Wen
2011-01-26 10:31 ` [U-Boot] [PATCH V7 3/5] serial: add pantheon soc support Lei Wen
2011-01-26 10:31 ` [U-Boot] [PATCH V7 4/5] mvmfp: add MFP configuration support for PANTHEON Lei Wen
2011-01-26 10:31 ` [U-Boot] [PATCH V7 5/5] Pantheon: Add Board Support for Marvell dkb board Lei Wen

This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.