* Hauppauge WinTV-HVR-1120 on Unbuntu 10.04
@ 2010-10-11 9:41 fabio tirapelle
2010-10-12 1:00 ` Zhang Rui
2010-10-12 20:27 ` Bjorn Helgaas
0 siblings, 2 replies; 13+ messages in thread
From: fabio tirapelle @ 2010-10-11 9:41 UTC (permalink / raw)
To: linux-acpi
Hi
After upgrading from Ubuntu 9.10 to Ubuntu 10.04 my Hauppauge WinTV-HVR-1120
(sometimes) doesn't work correctly.
I get random the following errors:
[ 53.216153] DVB: registering new adapter (saa7133[0])
[ 53.216156] DVB: registering adapter 2 frontend 0 (NXP TDA10048HN DVB-T)...
[ 53.840013] tda10048_firmware_upload: waiting for firmware upload
(dvb-fe-tda10048-1.0.fw)...
[ 53.840019] saa7134 0000:01:06.0: firmware: requesting dvb-fe-tda10048-1.0.fw
[ 53.880505] tda10048_firmware_upload: firmware read 24878 bytes.
[ 53.880509] tda10048_firmware_upload: firmware uploading
[ 58.280136] tda10048_firmware_upload: firmware uploaded
[ 59.024537] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 59.024541] tda18271c2_rf_tracking_filters_correction: error -5 on line 264
[ 59.420153] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 59.420157] tda18271_toggle_output: error -5 on line 47
[ 91.004019] Clocksource tsc unstable (delta = -295012684 ns)
[ 256.293639] eth0: link up.
[ 256.294750] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 263.523498] eth0: link down.
[ 265.258740] eth0: link up.
[ 266.460026] eth0: no IPv6 routers present
[ 9869.636167] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 9869.636178] tda18271_init: error -5 on line 826
[ 9872.636220] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 9872.636232] tda18271_toggle_output: error -5 on line 47
[ 9998.240167] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 9998.240178] tda18271_init: error -5 on line 826
[10001.240179] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[10001.240190] tda18271_toggle_output: error -5 on line 47
Any ideas?
Thanks
^ permalink raw reply [flat|nested] 13+ messages in thread* Re: Hauppauge WinTV-HVR-1120 on Unbuntu 10.04
2010-10-11 9:41 Hauppauge WinTV-HVR-1120 on Unbuntu 10.04 fabio tirapelle
@ 2010-10-12 1:00 ` Zhang Rui
2010-10-12 20:27 ` Bjorn Helgaas
1 sibling, 0 replies; 13+ messages in thread
From: Zhang Rui @ 2010-10-12 1:00 UTC (permalink / raw)
To: fabio tirapelle; +Cc: linux-acpi
On Mon, 2010-10-11 at 17:41 +0800, fabio tirapelle wrote:
> Hi
>
> After upgrading from Ubuntu 9.10 to Ubuntu 10.04 my Hauppauge WinTV-HVR-1120
> (sometimes) doesn't work correctly.
Well, this is not an ACPI problem, so I'm not sure why you report it
here.
thanks,
rui
> I get random the following errors:
>
> [ 53.216153] DVB: registering new adapter (saa7133[0])
> [ 53.216156] DVB: registering adapter 2 frontend 0 (NXP TDA10048HN DVB-T)...
> [ 53.840013] tda10048_firmware_upload: waiting for firmware upload
> (dvb-fe-tda10048-1.0.fw)...
> [ 53.840019] saa7134 0000:01:06.0: firmware: requesting dvb-fe-tda10048-1.0.fw
> [ 53.880505] tda10048_firmware_upload: firmware read 24878 bytes.
> [ 53.880509] tda10048_firmware_upload: firmware uploading
> [ 58.280136] tda10048_firmware_upload: firmware uploaded
> [ 59.024537] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 59.024541] tda18271c2_rf_tracking_filters_correction: error -5 on line 264
> [ 59.420153] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 59.420157] tda18271_toggle_output: error -5 on line 47
> [ 91.004019] Clocksource tsc unstable (delta = -295012684 ns)
> [ 256.293639] eth0: link up.
> [ 256.294750] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> [ 263.523498] eth0: link down.
> [ 265.258740] eth0: link up.
> [ 266.460026] eth0: no IPv6 routers present
> [ 9869.636167] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 9869.636178] tda18271_init: error -5 on line 826
> [ 9872.636220] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 9872.636232] tda18271_toggle_output: error -5 on line 47
> [ 9998.240167] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 9998.240178] tda18271_init: error -5 on line 826
> [10001.240179] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [10001.240190] tda18271_toggle_output: error -5 on line 47
>
>
>
> Any ideas?
> Thanks
>
>
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-acpi" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: Hauppauge WinTV-HVR-1120 on Unbuntu 10.04
2010-10-11 9:41 Hauppauge WinTV-HVR-1120 on Unbuntu 10.04 fabio tirapelle
2010-10-12 1:00 ` Zhang Rui
@ 2010-10-12 20:27 ` Bjorn Helgaas
1 sibling, 0 replies; 13+ messages in thread
From: Bjorn Helgaas @ 2010-10-12 20:27 UTC (permalink / raw)
To: fabio tirapelle; +Cc: linux-acpi
On Monday, October 11, 2010 03:41:17 am fabio tirapelle wrote:
> Hi
>
> After upgrading from Ubuntu 9.10 to Ubuntu 10.04 my Hauppauge WinTV-HVR-1120
> (sometimes) doesn't work correctly.
> I get random the following errors:
>
> [ 53.216153] DVB: registering new adapter (saa7133[0])
> [ 53.216156] DVB: registering adapter 2 frontend 0 (NXP TDA10048HN DVB-T)...
> [ 53.840013] tda10048_firmware_upload: waiting for firmware upload
> (dvb-fe-tda10048-1.0.fw)...
> [ 53.840019] saa7134 0000:01:06.0: firmware: requesting dvb-fe-tda10048-1.0.fw
> [ 53.880505] tda10048_firmware_upload: firmware read 24878 bytes.
> [ 53.880509] tda10048_firmware_upload: firmware uploading
> [ 58.280136] tda10048_firmware_upload: firmware uploaded
> [ 59.024537] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
Can you collect the complete dmesg log, please? If you still have
the 9.10 kernel and can collect a log from that for comparison, that
would be great, too.
I don't see an indication that it's ACPI-related, so maybe
linux-kernel@vger.kernel.org would be a better place. Please copy
me, too :-)
Bjorn
^ permalink raw reply [flat|nested] 13+ messages in thread
* Hauppauge WinTV-HVR-1120 on Unbuntu 10.04
@ 2010-10-11 9:57 fabio tirapelle
2010-10-19 18:32 ` Albin Kauffmann
0 siblings, 1 reply; 13+ messages in thread
From: fabio tirapelle @ 2010-10-11 9:57 UTC (permalink / raw)
To: linux-media
Hi
After upgrading from Ubuntu 9.10 to Ubuntu 10.04 my Hauppauge WinTV-HVR-1120
(sometimes) doesn't work correctly.
I get random the following errors:
[ 53.216153] DVB: registering new adapter (saa7133[0])
[ 53.216156] DVB: registering adapter 2 frontend 0 (NXP TDA10048HN DVB-T)...
[ 53.840013] tda10048_firmware_upload: waiting for firmware upload
(dvb-fe-tda10048-1.0.fw)...
[ 53.840019] saa7134 0000:01:06.0: firmware: requesting dvb-fe-tda10048-1.0.fw
[ 53.880505] tda10048_firmware_upload: firmware read 24878 bytes.
[ 53.880509] tda10048_firmware_upload: firmware uploading
[ 58.280136] tda10048_firmware_upload: firmware uploaded
[ 59.024537] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 59.024541] tda18271c2_rf_tracking_filters_correction: error -5 on line 264
[ 59.420153] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 59.420157] tda18271_toggle_output: error -5 on line 47
[ 91.004019] Clocksource tsc unstable (delta = -295012684 ns)
[ 256.293639] eth0: link up.
[ 256.294750] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 263.523498] eth0: link down.
[ 265.258740] eth0: link up.
[ 266.460026] eth0: no IPv6 routers present
[ 9869.636167] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 9869.636178] tda18271_init: error -5 on line 826
[ 9872.636220] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 9872.636232] tda18271_toggle_output: error -5 on line 47
[ 9998.240167] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 9998.240178] tda18271_init: error -5 on line 826
[10001.240179] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[10001.240190] tda18271_toggle_output: error -5 on line 47
Any ideas?
Thanks
^ permalink raw reply [flat|nested] 13+ messages in thread* Re: Hauppauge WinTV-HVR-1120 on Unbuntu 10.04
2010-10-11 9:57 fabio tirapelle
@ 2010-10-19 18:32 ` Albin Kauffmann
2010-10-19 19:56 ` fabio tirapelle
0 siblings, 1 reply; 13+ messages in thread
From: Albin Kauffmann @ 2010-10-19 18:32 UTC (permalink / raw)
To: fabio tirapelle; +Cc: linux-media
On Monday 11 October 2010 11:57:14 fabio tirapelle wrote:
> Hi
>
> After upgrading from Ubuntu 9.10 to Ubuntu 10.04 my Hauppauge
> WinTV-HVR-1120 (sometimes) doesn't work correctly.
> I get random the following errors:
>
> [ 53.216153] DVB: registering new adapter (saa7133[0])
> [ 53.216156] DVB: registering adapter 2 frontend 0 (NXP TDA10048HN
> DVB-T)... [ 53.840013] tda10048_firmware_upload: waiting for firmware
> upload (dvb-fe-tda10048-1.0.fw)...
> [ 53.840019] saa7134 0000:01:06.0: firmware: requesting
> dvb-fe-tda10048-1.0.fw [ 53.880505] tda10048_firmware_upload: firmware
> read 24878 bytes. [ 53.880509] tda10048_firmware_upload: firmware
> uploading
> [ 58.280136] tda10048_firmware_upload: firmware uploaded
> [ 59.024537] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 59.024541] tda18271c2_rf_tracking_filters_correction: error -5 on line
> 264 [ 59.420153] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
> i2c_transfer returned: -5
> [ 59.420157] tda18271_toggle_output: error -5 on line 47
> [ 91.004019] Clocksource tsc unstable (delta = -295012684 ns)
> [ 256.293639] eth0: link up.
> [ 256.294750] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> [ 263.523498] eth0: link down.
> [ 265.258740] eth0: link up.
> [ 266.460026] eth0: no IPv6 routers present
> [ 9869.636167] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 9869.636178] tda18271_init: error -5 on line 826
> [ 9872.636220] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 9872.636232] tda18271_toggle_output: error -5 on line 47
> [ 9998.240167] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 9998.240178] tda18271_init: error -5 on line 826
> [10001.240179] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [10001.240190] tda18271_toggle_output: error -5 on line 47
Hi,
I have the same HVR-1120 TV card and I get the same kind of errors happening
on my ArchLinux installation (kernel 2.6.35). However, these errors are not
occuring after all boots. Indeed, I can watch TV (DVB-T) with no problem after
3/4 of my reboots. Is your problem happening at all time ?
I've started to recompile my own kernel with the v4l module from the hg
repository. I'll tell you if it improves the behavior.
I don't use Ubuntu on my desktop computer but, as far as you are concerned,
you could first try to update your installation to the last Ubuntu 10.10 or to
compile the last Linux kernel. And tell us if it improves something ;)
Cheers,
--
Albin Kauffmann
Open Wide - Architecte Open Source
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: Hauppauge WinTV-HVR-1120 on Unbuntu 10.04
2010-10-19 18:32 ` Albin Kauffmann
@ 2010-10-19 19:56 ` fabio tirapelle
2010-10-24 14:27 ` Albin Kauffmann
0 siblings, 1 reply; 13+ messages in thread
From: fabio tirapelle @ 2010-10-19 19:56 UTC (permalink / raw)
To: Albin Kauffmann; +Cc: linux-media
Hi
Yes, the same behaviour: random (after 3-4 boots) the card works correctly.
The WinTV did work correctly with ubuntu 9.10. In Ubuntu 9.10 the
package linux-firmware-nonfree didn't include the dvb-fe-tda10048-1.0.fw. I
remember that Ubuntu 9.10 used for my card the dvb-fe-tda10046.fw.
Now, Ubuntu 10.04 loads for my card the dvb-fe-tda10048-1.0.fw
Its seems that with the 9.10 version, the card is recognized as WinTV-HVR-1100
or 1110 and now as WinTV-HVR-1120.
I wait until you recompile the kernel with the v4l. Please tell me if this
solves
the problem
Thanks
----- Messaggio originale -----
> Da: Albin Kauffmann <albin.kauffmann@gmail.com>
> A: fabio tirapelle <ftirapelle@yahoo.it>
> Cc: linux-media@vger.kernel.org
> Inviato: Mar 19 ottobre 2010, 20:32:50
> Oggetto: Re: Hauppauge WinTV-HVR-1120 on Unbuntu 10.04
>
> On Monday 11 October 2010 11:57:14 fabio tirapelle wrote:
> > Hi
> >
> > After upgrading from Ubuntu 9.10 to Ubuntu 10.04 my Hauppauge
> > WinTV-HVR-1120 (sometimes) doesn't work correctly.
> > I get random the following errors:
> >
> > [ 53.216153] DVB: registering new adapter (saa7133[0])
> > [ 53.216156] DVB: registering adapter 2 frontend 0 (NXP TDA10048HN
> > DVB-T)... [ 53.840013] tda10048_firmware_upload: waiting for firmware
> > upload (dvb-fe-tda10048-1.0.fw)...
> > [ 53.840019] saa7134 0000:01:06.0: firmware: requesting
> > dvb-fe-tda10048-1.0.fw [ 53.880505] tda10048_firmware_upload: firmware
> > read 24878 bytes. [ 53.880509] tda10048_firmware_upload: firmware
> > uploading
> > [ 58.280136] tda10048_firmware_upload: firmware uploaded
> > [ 59.024537] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> > returned: -5
> > [ 59.024541] tda18271c2_rf_tracking_filters_correction: error -5 on line
> > 264 [ 59.420153] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
> > i2c_transfer returned: -5
> > [ 59.420157] tda18271_toggle_output: error -5 on line 47
> > [ 91.004019] Clocksource tsc unstable (delta = -295012684 ns)
> > [ 256.293639] eth0: link up.
> > [ 256.294750] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> > [ 263.523498] eth0: link down.
> > [ 265.258740] eth0: link up.
> > [ 266.460026] eth0: no IPv6 routers present
> > [ 9869.636167] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> > returned: -5
> > [ 9869.636178] tda18271_init: error -5 on line 826
> > [ 9872.636220] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> > returned: -5
> > [ 9872.636232] tda18271_toggle_output: error -5 on line 47
> > [ 9998.240167] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> > returned: -5
> > [ 9998.240178] tda18271_init: error -5 on line 826
> > [10001.240179] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
i2c_transfer
> > returned: -5
> > [10001.240190] tda18271_toggle_output: error -5 on line 47
>
> Hi,
>
> I have the same HVR-1120 TV card and I get the same kind of errors happening
> on my ArchLinux installation (kernel 2.6.35). However, these errors are not
> occuring after all boots. Indeed, I can watch TV (DVB-T) with no problem after
>
> 3/4 of my reboots. Is your problem happening at all time ?
>
> I've started to recompile my own kernel with the v4l module from the hg
> repository. I'll tell you if it improves the behavior.
>
> I don't use Ubuntu on my desktop computer but, as far as you are concerned,
> you could first try to update your installation to the last Ubuntu 10.10 or to
>
> compile the last Linux kernel. And tell us if it improves something ;)
>
> Cheers,
>
> --
> Albin Kauffmann
> Open Wide - Architecte Open Source
> --
> To unsubscribe from this list: send the line "unsubscribe linux-media" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
^ permalink raw reply [flat|nested] 13+ messages in thread* Re: Hauppauge WinTV-HVR-1120 on Unbuntu 10.04
2010-10-19 19:56 ` fabio tirapelle
@ 2010-10-24 14:27 ` Albin Kauffmann
2011-01-11 13:57 ` mmanzato
0 siblings, 1 reply; 13+ messages in thread
From: Albin Kauffmann @ 2010-10-24 14:27 UTC (permalink / raw)
To: fabio tirapelle, Sasha Sirotkin; +Cc: linux-media
On Tuesday 19 October 2010 21:56:51 fabio tirapelle wrote:
> The WinTV did work correctly with ubuntu 9.10. In Ubuntu 9.10 the
> package linux-firmware-nonfree didn't include the dvb-fe-tda10048-1.0.fw. I
> remember that Ubuntu 9.10 used for my card the dvb-fe-tda10046.fw.
>
> Now, Ubuntu 10.04 loads for my card the dvb-fe-tda10048-1.0.fw
> Its seems that with the 9.10 version, the card is recognized as
> WinTV-HVR-1100 or 1110 and now as WinTV-HVR-1120.
This is actually strange because the Wiki states that the card is using an
"NXP TDA10048 digital demodulator"
(http://linuxtv.org/wiki/index.php/Hauppauge_WinTV-HVR-1120). Anyway, this may
worth the cost to build an old kernel to see if this effectively works well ;)
> I wait until you recompile the kernel with the v4l. Please tell me if this
> solves the problem
I have tried several scenarios :
- the last 2.6.36 Linux kernel
- the kernel 2.6.35 with sources from the HG repository
(http://linuxtv.org/hg/v4l-dvb/)
- the media tree git (http://git.linuxtv.org/media_tree.git)
In all situations, I get the same behaviour. After a random number of reboots,
the TV (DVB-T) is not working and I get this message displayed in loop in
`dmesg`:
tda18271_write_regs: [1-0060|M] ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
tda18271_init: [1-0060|M] error -5 on line 830
tda18271_tune: [1-0060|M] error -5 on line 908
tda18271_set_params: [1-0060|M] error -5 on line 989
Also, even when the TV is working, I get these error messages in `dmesg:
[...]
tda829x 1-004b: type set to tda8290
tda18271 1-0060: attaching existing instance
DVB: registering new adapter (saa7133[0])
DVB: registering adapter 0 frontend 0 (NXP TDA10048HN DVB-T)...
tda10048_firmware_upload: waiting for firmware upload (dvb-fe-
tda10048-1.0.fw)...
tda10048_firmware_upload: firmware read 24878 bytes.
tda10048_firmware_upload: firmware uploading
tda18271_write_regs: [1-0060|M] ERROR: idx = 0x13, len = 1, i2c_transfer
returned: -5
tda18271_write_regs: [1-0060|M] ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
tda18271_set_analog_params: [1-0060|M] error -5 on line 1045
tda18271_write_regs: [1-0060|M] ERROR: idx = 0x13, len = 1, i2c_transfer
returned: -5
tda10048_firmware_upload: firmware uploaded
saa7134 ALSA driver for DMA sound loaded
saa7133[0]/alsa: saa7133[0] at 0xeb200000 irq 20 registered as card -1
tda18271_read_regs: [1-0060|M] ERROR: i2c_transfer returned: -5
tda18271_ir_cal_init: [1-0060|M] error -5 on line 811
tda18271_init: [1-0060|M] error -5 on line 835
tda18271_tune: [1-0060|M] error -5 on line 908
tda18271_set_analog_params: [1-0060|M] error -5 on line 1045
I may take a look at sources to understand what is happening. So, if someone
have an idea, please tell me ;)
Thanks,
--
Albin Kauffmann
^ permalink raw reply [flat|nested] 13+ messages in thread
* Hauppauge WinTV-HVR-1120 on Unbuntu 10.04
@ 2010-10-13 19:02 fabio tirapelle
2010-10-13 19:54 ` Bjorn Helgaas
0 siblings, 1 reply; 13+ messages in thread
From: fabio tirapelle @ 2010-10-13 19:02 UTC (permalink / raw)
To: linux-kernel; +Cc: bjorn.helgaas
Hi
After upgrading from Ubuntu 9.10 to Ubuntu 10.04 my Hauppauge WinTV-HVR-1120
(sometimes) doesn't work correctly.
I get random the following errors:
tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer returned: -5
tda18271_init: error -5 on line 826
tda18271_tune: error -5 on line 904
tda18271_set_params: error -5 on line 985
Part of dmesg of 11-OCT-2010
[ 53.216153] DVB: registering new adapter (saa7133[0])
[ 53.216156] DVB: registering adapter 2 frontend 0 (NXP TDA10048HN DVB-T)...
[ 53.840013] tda10048_firmware_upload: waiting for firmware upload
(dvb-fe-tda10048-1.0.fw)...
[ 53.840019] saa7134 0000:01:06.0: firmware: requesting dvb-fe-tda10048-1.0.fw
[ 53.880505] tda10048_firmware_upload: firmware read 24878 bytes.
[ 53.880509] tda10048_firmware_upload: firmware uploading
[ 58.280136] tda10048_firmware_upload: firmware uploaded
[ 59.024537] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 59.024541] tda18271c2_rf_tracking_filters_correction: error -5 on line 264
[ 59.420153] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 59.420157] tda18271_toggle_output: error -5 on line 47
[ 91.004019] Clocksource tsc unstable (delta = -295012684 ns)
[ 256.293639] eth0: link up.
[ 256.294750] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 263.523498] eth0: link down.
[ 265.258740] eth0: link up.
[ 266.460026] eth0: no IPv6 routers present
[ 9869.636167] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 9869.636178] tda18271_init: error -5 on line 826
[ 9872.636220] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 9872.636232] tda18271_toggle_output: error -5 on line 47
[ 9998.240167] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 9998.240178] tda18271_init: error -5 on line 826
[10001.240179] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[10001.240190] tda18271_toggle_output: error -5 on line 47
And this is the dmesg of today: even the same errors.
[ 741.252183] tda18271_init: error -5 on line 826
[ 741.252188] tda18271_tune: error -5 on line 904
[ 741.252193] tda18271_set_params: error -5 on line 985
[ 742.268174] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 742.268184] tda18271_init: error -5 on line 826
[ 742.268189] tda18271_tune: error -5 on line 904
[ 742.268194] tda18271_set_params: error -5 on line 985
[ 743.284174] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 743.284184] tda18271_init: error -5 on line 826
[ 743.284190] tda18271_tune: error -5 on line 904
[ 743.284194] tda18271_set_params: error -5 on line 985
[ 744.300169] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 744.300180] tda18271_init: error -5 on line 826
[ 744.300185] tda18271_tune: error -5 on line 904
[ 744.300190] tda18271_set_params: error -5 on line 985
[ 745.320172] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 745.320183] tda18271_init: error -5 on line 826
[ 745.320188] tda18271_tune: error -5 on line 904
[ 745.320193] tda18271_set_params: error -5 on line 985
[ 746.336174] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 746.336185] tda18271_init: error -5 on line 826
[ 746.336190] tda18271_tune: error -5 on line 904
[ 746.336195] tda18271_set_params: error -5 on line 985
[ 747.352170] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 747.352181] tda18271_init: error -5 on line 826
[ 747.352187] tda18271_tune: error -5 on line 904
[ 747.352192] tda18271_set_params: error -5 on line 985
[ 748.368172] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 748.368183] tda18271_init: error -5 on line 826
[ 748.368188] tda18271_tune: error -5 on line 904
[ 748.368193] tda18271_set_params: error -5 on line 985
[ 749.384179] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 749.384191] tda18271_init: error -5 on line 826
[ 749.384196] tda18271_tune: error -5 on line 904
[ 749.384202] tda18271_set_params: error -5 on line 985
[ 750.400172] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 750.400182] tda18271_init: error -5 on line 826
[ 750.400188] tda18271_tune: error -5 on line 904
[ 750.400194] tda18271_set_params: error -5 on line 985
[ 751.424170] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
[ 751.424181] tda18271_init: error -5 on line 826
[ 751.424186] tda18271_tune: error -5 on line 904
[ 751.424192] tda18271_set_params: error -5 on line 985
[ 752.440172] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
returned: -5
Any ideas?
Thanks
^ permalink raw reply [flat|nested] 13+ messages in thread* Re: Hauppauge WinTV-HVR-1120 on Unbuntu 10.04
2010-10-13 19:02 fabio tirapelle
@ 2010-10-13 19:54 ` Bjorn Helgaas
0 siblings, 0 replies; 13+ messages in thread
From: Bjorn Helgaas @ 2010-10-13 19:54 UTC (permalink / raw)
To: fabio tirapelle; +Cc: linux-kernel, Michael Krufky
On Wednesday, October 13, 2010 01:02:11 pm fabio tirapelle wrote:
> After upgrading from Ubuntu 9.10 to Ubuntu 10.04 my Hauppauge WinTV-HVR-1120
> (sometimes) doesn't work correctly.
> I get random the following errors:
>
> tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer returned: -5
> tda18271_init: error -5 on line 826
> tda18271_tune: error -5 on line 904
> tda18271_set_params: error -5 on line 985
I cc'd Michael since he made several recent tda18271 changes.
This page: http://cvs.linuxtv.org/wiki/index.php/Zolid_Hybrid_TV_Tuner
suggests that the card might work, despite the error messages. Does
yours work?
I see that tda18271_write_regs() uses i2c_transfer(), which uses the
adap->algo->master_xfer function pointer, but I don't know enough to
figure out which master_xfer implementation might be used on your
system. A complete dmesg log and lspci output might have a hint.
Can you reproduce this on an upstream kernel? It would be good to
make sure that it's not something introduced by an Ubuntu patch or
fixed since the Ubuntu kernel snapshot.
Bjorn
> Part of dmesg of 11-OCT-2010
>
> [ 53.216153] DVB: registering new adapter (saa7133[0])
> [ 53.216156] DVB: registering adapter 2 frontend 0 (NXP TDA10048HN DVB-T)...
> [ 53.840013] tda10048_firmware_upload: waiting for firmware upload
> (dvb-fe-tda10048-1.0.fw)...
> [ 53.840019] saa7134 0000:01:06.0: firmware: requesting dvb-fe-tda10048-1.0.fw
> [ 53.880505] tda10048_firmware_upload: firmware read 24878 bytes.
> [ 53.880509] tda10048_firmware_upload: firmware uploading
> [ 58.280136] tda10048_firmware_upload: firmware uploaded
> [ 59.024537] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 59.024541] tda18271c2_rf_tracking_filters_correction: error -5 on line 264
> [ 59.420153] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 59.420157] tda18271_toggle_output: error -5 on line 47
> [ 91.004019] Clocksource tsc unstable (delta = -295012684 ns)
> [ 256.293639] eth0: link up.
> [ 256.294750] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> [ 263.523498] eth0: link down.
> [ 265.258740] eth0: link up.
> [ 266.460026] eth0: no IPv6 routers present
> [ 9869.636167] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 9869.636178] tda18271_init: error -5 on line 826
> [ 9872.636220] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 9872.636232] tda18271_toggle_output: error -5 on line 47
> [ 9998.240167] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 9998.240178] tda18271_init: error -5 on line 826
> [10001.240179] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [10001.240190] tda18271_toggle_output: error -5 on line 47
>
> And this is the dmesg of today: even the same errors.
>
> [ 741.252183] tda18271_init: error -5 on line 826
> [ 741.252188] tda18271_tune: error -5 on line 904
> [ 741.252193] tda18271_set_params: error -5 on line 985
> [ 742.268174] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 742.268184] tda18271_init: error -5 on line 826
> [ 742.268189] tda18271_tune: error -5 on line 904
> [ 742.268194] tda18271_set_params: error -5 on line 985
> [ 743.284174] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 743.284184] tda18271_init: error -5 on line 826
> [ 743.284190] tda18271_tune: error -5 on line 904
> [ 743.284194] tda18271_set_params: error -5 on line 985
> [ 744.300169] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 744.300180] tda18271_init: error -5 on line 826
> [ 744.300185] tda18271_tune: error -5 on line 904
> [ 744.300190] tda18271_set_params: error -5 on line 985
> [ 745.320172] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 745.320183] tda18271_init: error -5 on line 826
> [ 745.320188] tda18271_tune: error -5 on line 904
> [ 745.320193] tda18271_set_params: error -5 on line 985
> [ 746.336174] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 746.336185] tda18271_init: error -5 on line 826
> [ 746.336190] tda18271_tune: error -5 on line 904
> [ 746.336195] tda18271_set_params: error -5 on line 985
> [ 747.352170] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 747.352181] tda18271_init: error -5 on line 826
> [ 747.352187] tda18271_tune: error -5 on line 904
> [ 747.352192] tda18271_set_params: error -5 on line 985
> [ 748.368172] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 748.368183] tda18271_init: error -5 on line 826
> [ 748.368188] tda18271_tune: error -5 on line 904
> [ 748.368193] tda18271_set_params: error -5 on line 985
> [ 749.384179] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 749.384191] tda18271_init: error -5 on line 826
> [ 749.384196] tda18271_tune: error -5 on line 904
> [ 749.384202] tda18271_set_params: error -5 on line 985
> [ 750.400172] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 750.400182] tda18271_init: error -5 on line 826
> [ 750.400188] tda18271_tune: error -5 on line 904
> [ 750.400194] tda18271_set_params: error -5 on line 985
> [ 751.424170] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
> [ 751.424181] tda18271_init: error -5 on line 826
> [ 751.424186] tda18271_tune: error -5 on line 904
> [ 751.424192] tda18271_set_params: error -5 on line 985
> [ 752.440172] tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
> returned: -5
>
>
>
> Any ideas?
> Thanks
>
>
>
>
^ permalink raw reply [flat|nested] 13+ messages in thread
* Hauppauge WinTV-HVR-1120 on Unbuntu 10.04
@ 2010-10-13 21:26 fabio tirapelle
0 siblings, 0 replies; 13+ messages in thread
From: fabio tirapelle @ 2010-10-13 21:26 UTC (permalink / raw)
To: Bjorn Helgaas; +Cc: linux-kernel, Michael Krufky
[-- Attachment #1: Type: text/plain, Size: 10301 bytes --]
Yesterday I have installed (added not substituted) a new tuner: Hauppauge
Nova-T Stick 3
Today the WinTV-HVR-1120 doesn't works.
I attach my /var/log/messages
lsusb
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 15c2:0036 SoundGraph Inc.
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 002: ID 2040:7070 Hauppauge Nova-T Stick 3
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
lscpi
00:00.0 RAM memory: nVidia Corporation MCP78S [GeForce 8200] Memory Controller
(rev a2)
00:01.0 ISA bridge: nVidia Corporation MCP78S [GeForce 8200] LPC Bridge (rev
a2)
00:01.1 SMBus: nVidia Corporation MCP78S [GeForce 8200] SMBus (rev a1)
00:01.2 RAM memory: nVidia Corporation MCP78S [GeForce 8200] Memory Controller
(rev a1)
00:01.3 Co-processor: nVidia Corporation MCP78S [GeForce 8200] Co-Processor
(rev
a2)
00:01.4 RAM memory: nVidia Corporation MCP78S [GeForce 8200] Memory Controller
(rev a1)
00:02.0 USB Controller: nVidia Corporation MCP78S [GeForce 8200] OHCI USB 1.1
Controller (rev a1)
00:02.1 USB Controller: nVidia Corporation MCP78S [GeForce 8200] EHCI USB 2.0
Controller (rev a1)
00:04.0 USB Controller: nVidia Corporation MCP78S [GeForce 8200] OHCI USB 1.1
Controller (rev a1)
00:04.1 USB Controller: nVidia Corporation MCP78S [GeForce 8200] EHCI USB 2.0
Controller (rev a1)
00:06.0 IDE interface: nVidia Corporation MCP78S [GeForce 8200] IDE (rev a1)
00:07.0 Audio device: nVidia Corporation MCP72XE/MCP72P/MCP78U/MCP78S High
Definition Audio (rev a1)
00:08.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Bridge (rev
a1)
00:09.0 IDE interface: nVidia Corporation MCP78S [GeForce 8200] SATA Controller
(non-AHCI mode) (rev a2)
00:0a.0 Ethernet controller: nVidia Corporation MCP77 Ethernet (rev a2)
00:0b.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Express Bridge
(rev a1)
00:10.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Express Bridge
(rev a1)
00:12.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Express Bridge
(rev a1)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address
Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM
Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control
01:06.0 Multimedia controller: Philips Semiconductors SAA7131/SAA7133/SAA7135
Video Broadcast Decoder (rev d1)
01:07.0 Network controller: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip
/
Technisat SkyStar2 DVB card (rev 02)
02:00.0 VGA compatible controller: nVidia Corporation C77 [GeForce 8200] (rev
a2)
> ----- Messaggio originale -----
> > Da: Bjorn Helgaas <bjorn.helgaas@hp.com>
> > A: fabio tirapelle <ftirapelle@yahoo.it>
> > Cc: linux-kernel@vger.kernel.org; Michael Krufky <mkrufky@kernellabs.com>
> > Inviato: Mer 13 ottobre 2010, 21:54:31
> > Oggetto: Re: Hauppauge WinTV-HVR-1120 on Unbuntu 10.04
> >
> > On Wednesday, October 13, 2010 01:02:11 pm fabio tirapelle wrote:
> > > After upgrading from Ubuntu 9.10 to Ubuntu 10.04 my Hauppauge
>WinTV-HVR-1120
>
> >
> > > (sometimes) doesn't work correctly.
> > > I get random the following errors:
> > >
> > > tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer returned:
-5
> > > tda18271_init: error -5 on line 826
> > > tda18271_tune: error -5 on line 904
> > > tda18271_set_params: error -5 on line 985
> >
> > I cc'd Michael since he made several recent tda18271 changes.
> >
> > This page: http://cvs.linuxtv.org/wiki/index.php/Zolid_Hybrid_TV_Tuner
> > suggests that the card might work, despite the error messages. Does
> > yours work?
> >
> > I see that tda18271_write_regs() uses i2c_transfer(), which uses the
> > adap->algo->master_xfer function pointer, but I don't know enough to
> > figure out which master_xfer implementation might be used on your
> > system. A complete dmesg log and lspci output might have a hint.
> >
> > Can you reproduce this on an upstream kernel? It would be good to
> > make sure that it's not something introduced by an Ubuntu patch or
> > fixed since the Ubuntu kernel snapshot.
> >
> > Bjorn
> >
> > > Part of dmesg of 11-OCT-2010
> > >
> > > [ 53.216153] DVB: registering new adapter (saa7133[0])
> > > [ 53.216156] DVB: registering adapter 2 frontend 0 (NXP TDA10048HN
> >DVB-T)...
> > > [ 53.840013] tda10048_firmware_upload: waiting for firmware upload
> > > (dvb-fe-tda10048-1.0.fw)...
> > > [ 53.840019] saa7134 0000:01:06.0: firmware: requesting
> >dvb-fe-tda10048-1.0.fw
> > > [ 53.880505] tda10048_firmware_upload: firmware read 24878 bytes.
> > > [ 53.880509] tda10048_firmware_upload: firmware uploading
> > > [ 58.280136] tda10048_firmware_upload: firmware uploaded
> > > [ 59.024537] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
>i2c_transfer
>
>
> > > returned: -5
> > > [ 59.024541] tda18271c2_rf_tracking_filters_correction: error -5 on
>line
>
> >264
> > > [ 59.420153] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
>i2c_transfer
>
>
> > > returned: -5
> > > [ 59.420157] tda18271_toggle_output: error -5 on line 47
> > > [ 91.004019] Clocksource tsc unstable (delta = -295012684 ns)
> > > [ 256.293639] eth0: link up.
> > > [ 256.294750] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> > > [ 263.523498] eth0: link down.
> > > [ 265.258740] eth0: link up.
> > > [ 266.460026] eth0: no IPv6 routers present
> > > [ 9869.636167] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
>i2c_transfer
>
>
> > > returned: -5
> > > [ 9869.636178] tda18271_init: error -5 on line 826
> > > [ 9872.636220] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
>i2c_transfer
>
>
> > > returned: -5
> > > [ 9872.636232] tda18271_toggle_output: error -5 on line 47
> > > [ 9998.240167] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
>i2c_transfer
>
>
> > > returned: -5
> > > [ 9998.240178] tda18271_init: error -5 on line 826
> > > [10001.240179] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
>i2c_transfer
>
>
> > > returned: -5
> > > [10001.240190] tda18271_toggle_output: error -5 on line 47
> > >
> > > And this is the dmesg of today: even the same errors.
> > >
> > > [ 741.252183] tda18271_init: error -5 on line 826
> > > [ 741.252188] tda18271_tune: error -5 on line 904
> > > [ 741.252193] tda18271_set_params: error -5 on line 985
> > > [ 742.268174] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
>i2c_transfer
>
>
> > > returned: -5
> > > [ 742.268184] tda18271_init: error -5 on line 826
> > > [ 742.268189] tda18271_tune: error -5 on line 904
> > > [ 742.268194] tda18271_set_params: error -5 on line 985
> > > [ 743.284174] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
>i2c_transfer
>
>
> > > returned: -5
> > > [ 743.284184] tda18271_init: error -5 on line 826
> > > [ 743.284190] tda18271_tune: error -5 on line 904
> > > [ 743.284194] tda18271_set_params: error -5 on line 985
> > > [ 744.300169] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
>i2c_transfer
>
>
> > > returned: -5
> > > [ 744.300180] tda18271_init: error -5 on line 826
> > > [ 744.300185] tda18271_tune: error -5 on line 904
> > > [ 744.300190] tda18271_set_params: error -5 on line 985
> > > [ 745.320172] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
>i2c_transfer
>
>
> > > returned: -5
> > > [ 745.320183] tda18271_init: error -5 on line 826
> > > [ 745.320188] tda18271_tune: error -5 on line 904
> > > [ 745.320193] tda18271_set_params: error -5 on line 985
> > > [ 746.336174] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
>i2c_transfer
>
>
> > > returned: -5
> > > [ 746.336185] tda18271_init: error -5 on line 826
> > > [ 746.336190] tda18271_tune: error -5 on line 904
> > > [ 746.336195] tda18271_set_params: error -5 on line 985
> > > [ 747.352170] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
>i2c_transfer
>
>
> > > returned: -5
> > > [ 747.352181] tda18271_init: error -5 on line 826
> > > [ 747.352187] tda18271_tune: error -5 on line 904
> > > [ 747.352192] tda18271_set_params: error -5 on line 985
> > > [ 748.368172] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
>i2c_transfer
>
>
> > > returned: -5
> > > [ 748.368183] tda18271_init: error -5 on line 826
> > > [ 748.368188] tda18271_tune: error -5 on line 904
> > > [ 748.368193] tda18271_set_params: error -5 on line 985
> > > [ 749.384179] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
>i2c_transfer
>
>
> > > returned: -5
> > > [ 749.384191] tda18271_init: error -5 on line 826
> > > [ 749.384196] tda18271_tune: error -5 on line 904
> > > [ 749.384202] tda18271_set_params: error -5 on line 985
> > > [ 750.400172] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
>i2c_transfer
>
>
> > > returned: -5
> > > [ 750.400182] tda18271_init: error -5 on line 826
> > > [ 750.400188] tda18271_tune: error -5 on line 904
> > > [ 750.400194] tda18271_set_params: error -5 on line 985
> > > [ 751.424170] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
>i2c_transfer
>
>
> > > returned: -5
> > > [ 751.424181] tda18271_init: error -5 on line 826
> > > [ 751.424186] tda18271_tune: error -5 on line 904
> > > [ 751.424192] tda18271_set_params: error -5 on line 985
> > > [ 752.440172] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
>i2c_transfer
>
>
> > > returned: -5
> > >
>
>
> >
> >
> > >
> > >
> > > Any ideas?
> > > Thanks
> > >
> > >
> > >
> > >
> >
>
>
>
[-- Attachment #2: messages.zip --]
[-- Type: application/zip, Size: 27956 bytes --]
^ permalink raw reply [flat|nested] 13+ messages in thread* Re: Hauppauge WinTV-HVR-1120 on Unbuntu 10.04
@ 2010-10-14 12:22 fabio tirapelle
0 siblings, 0 replies; 13+ messages in thread
From: fabio tirapelle @ 2010-10-14 12:22 UTC (permalink / raw)
To: Bjorn Helgaas; +Cc: linux-kernel, Michael Krufky
The WinTV did work correctly with ubuntu 9.10. In this version of Ubuntu the
package linux-firmware-nonfree didn't include the dvb-fe-tda10048-1.0.fw. I
remember that Ubuntu 9.10 used dvb-fe-tda10046.fw.
Now, Ubuntu 10.04 loads for my card the dvb-fe-tda10048-1.0.fw
Its seems that with the 9.10 version, the card is recognized as WinTV-HVR-1100
or 1110 and now as WinTV-HVR-1120.
http://linuxtv.org/wiki/index.php/Hauppauge_WinTV-HVR-1110
http://linuxtv.org/wiki/index.php/Hauppauge_WinTV-HVR-1120
How recognize Linux the version of the card?
Thanks
----- Messaggio originale -----
> Da: fabio tirapelle <ftirapelle@yahoo.it>
> A: Bjorn Helgaas <bjorn.helgaas@hp.com>
> Cc: linux-kernel@vger.kernel.org; Michael Krufky <mkrufky@kernellabs.com>
> Inviato: Mer 13 ottobre 2010, 23:26:02
> Oggetto: Hauppauge WinTV-HVR-1120 on Unbuntu 10.04
>
>
> Yesterday I have installed (added not substituted) a new tuner: Hauppauge
> Nova-T Stick 3
> Today the WinTV-HVR-1120 doesn't works.
> I attach my /var/log/messages
>
> lsusb
>
> Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
> Bus 003 Device 002: ID 15c2:0036 SoundGraph Inc.
> Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
> Bus 002 Device 002: ID 2040:7070 Hauppauge Nova-T Stick 3
> Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
>
>
> lscpi
>
> 00:00.0 RAM memory: nVidia Corporation MCP78S [GeForce 8200] Memory
>Controller
> (rev a2)
> 00:01.0 ISA bridge: nVidia Corporation MCP78S [GeForce 8200] LPC Bridge (rev
> a2)
> 00:01.1 SMBus: nVidia Corporation MCP78S [GeForce 8200] SMBus (rev a1)
> 00:01.2 RAM memory: nVidia Corporation MCP78S [GeForce 8200] Memory
>Controller
> (rev a1)
> 00:01.3 Co-processor: nVidia Corporation MCP78S [GeForce 8200] Co-Processor
> (rev
> a2)
> 00:01.4 RAM memory: nVidia Corporation MCP78S [GeForce 8200] Memory
>Controller
> (rev a1)
> 00:02.0 USB Controller: nVidia Corporation MCP78S [GeForce 8200] OHCI USB
1.1
> Controller (rev a1)
> 00:02.1 USB Controller: nVidia Corporation MCP78S [GeForce 8200] EHCI USB
2.0
> Controller (rev a1)
> 00:04.0 USB Controller: nVidia Corporation MCP78S [GeForce 8200] OHCI USB
1.1
> Controller (rev a1)
> 00:04.1 USB Controller: nVidia Corporation MCP78S [GeForce 8200] EHCI USB
>2.0
> Controller (rev a1)
> 00:06.0 IDE interface: nVidia Corporation MCP78S [GeForce 8200] IDE (rev a1)
> 00:07.0 Audio device: nVidia Corporation MCP72XE/MCP72P/MCP78U/MCP78S High
> Definition Audio (rev a1)
> 00:08.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Bridge (rev
> a1)
> 00:09.0 IDE interface: nVidia Corporation MCP78S [GeForce 8200] SATA
>Controller
> (non-AHCI mode) (rev a2)
> 00:0a.0 Ethernet controller: nVidia Corporation MCP77 Ethernet (rev a2)
> 00:0b.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Express
>Bridge
> (rev a1)
> 00:10.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Express
>Bridge
> (rev a1)
> 00:12.0 PCI bridge: nVidia Corporation MCP78S [GeForce 8200] PCI Express
>Bridge
> (rev a1)
> 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
> HyperTransport Technology Configuration
> 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
>Address
> Map
> 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM
> Controller
> 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
> Miscellaneous Control
> 01:06.0 Multimedia controller: Philips Semiconductors
SAA7131/SAA7133/SAA7135
> Video Broadcast Decoder (rev d1)
> 01:07.0 Network controller: Techsan Electronics Co Ltd B2C2 FlexCopII DVB
>chip
>
> /
> Technisat SkyStar2 DVB card (rev 02)
> 02:00.0 VGA compatible controller: nVidia Corporation C77 [GeForce 8200]
(rev
> a2)
>
>
> > ----- Messaggio originale -----
> > > Da: Bjorn Helgaas <bjorn.helgaas@hp.com>
> > > A: fabio tirapelle <ftirapelle@yahoo.it>
> > > Cc: linux-kernel@vger.kernel.org; Michael Krufky
<mkrufky@kernellabs.com>
> > > Inviato: Mer 13 ottobre 2010, 21:54:31
> > > Oggetto: Re: Hauppauge WinTV-HVR-1120 on Unbuntu 10.04
> > >
> > > On Wednesday, October 13, 2010 01:02:11 pm fabio tirapelle wrote:
> > > > After upgrading from Ubuntu 9.10 to Ubuntu 10.04 my Hauppauge
> >WinTV-HVR-1120
> >
> > >
> > > > (sometimes) doesn't work correctly.
> > > > I get random the following errors:
> > > >
> > > > tda18271_write_regs: ERROR: idx = 0x5, len = 1, i2c_transfer
>returned:
>
> -5
> > > > tda18271_init: error -5 on line 826
> > > > tda18271_tune: error -5 on line 904
> > > > tda18271_set_params: error -5 on line 985
> > >
> > > I cc'd Michael since he made several recent tda18271 changes.
> > >
> > > This page: http://cvs.linuxtv.org/wiki/index.php/Zolid_Hybrid_TV_Tuner
> > > suggests that the card might work, despite the error messages. Does
> > > yours work?
> > >
> > > I see that tda18271_write_regs() uses i2c_transfer(), which uses the
> > > adap->algo->master_xfer function pointer, but I don't know enough to
> > > figure out which master_xfer implementation might be used on your
> > > system. A complete dmesg log and lspci output might have a hint.
> > >
> > > Can you reproduce this on an upstream kernel? It would be good to
> > > make sure that it's not something introduced by an Ubuntu patch or
> > > fixed since the Ubuntu kernel snapshot.
> > >
> > > Bjorn
> > >
> > > > Part of dmesg of 11-OCT-2010
> > > >
> > > > [ 53.216153] DVB: registering new adapter (saa7133[0])
> > > > [ 53.216156] DVB: registering adapter 2 frontend 0 (NXP TDA10048HN
> > >DVB-T)...
> > > > [ 53.840013] tda10048_firmware_upload: waiting for firmware upload
> > > > (dvb-fe-tda10048-1.0.fw)...
> > > > [ 53.840019] saa7134 0000:01:06.0: firmware: requesting
> > >dvb-fe-tda10048-1.0.fw
> > > > [ 53.880505] tda10048_firmware_upload: firmware read 24878 bytes.
> > > > [ 53.880509] tda10048_firmware_upload: firmware uploading
> > > > [ 58.280136] tda10048_firmware_upload: firmware uploaded
> > > > [ 59.024537] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
> >i2c_transfer
> >
> >
> > > > returned: -5
> > > > [ 59.024541] tda18271c2_rf_tracking_filters_correction: error -5 on
> >line
> >
> > >264
> > > > [ 59.420153] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
> >i2c_transfer
> >
> >
> > > > returned: -5
> > > > [ 59.420157] tda18271_toggle_output: error -5 on line 47
> > > > [ 91.004019] Clocksource tsc unstable (delta = -295012684 ns)
> > > > [ 256.293639] eth0: link up.
> > > > [ 256.294750] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
> > > > [ 263.523498] eth0: link down.
> > > > [ 265.258740] eth0: link up.
> > > > [ 266.460026] eth0: no IPv6 routers present
> > > > [ 9869.636167] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
> >i2c_transfer
> >
> >
> > > > returned: -5
> > > > [ 9869.636178] tda18271_init: error -5 on line 826
> > > > [ 9872.636220] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
> >i2c_transfer
> >
> >
> > > > returned: -5
> > > > [ 9872.636232] tda18271_toggle_output: error -5 on line 47
> > > > [ 9998.240167] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
> >i2c_transfer
> >
> >
> > > > returned: -5
> > > > [ 9998.240178] tda18271_init: error -5 on line 826
> > > > [10001.240179] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
> >i2c_transfer
> >
> >
> > > > returned: -5
> > > > [10001.240190] tda18271_toggle_output: error -5 on line 47
> > > >
> > > > And this is the dmesg of today: even the same errors.
> > > >
> > > > [ 741.252183] tda18271_init: error -5 on line 826
> > > > [ 741.252188] tda18271_tune: error -5 on line 904
> > > > [ 741.252193] tda18271_set_params: error -5 on line 985
> > > > [ 742.268174] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
> >i2c_transfer
> >
> >
> > > > returned: -5
> > > > [ 742.268184] tda18271_init: error -5 on line 826
> > > > [ 742.268189] tda18271_tune: error -5 on line 904
> > > > [ 742.268194] tda18271_set_params: error -5 on line 985
> > > > [ 743.284174] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
> >i2c_transfer
> >
> >
> > > > returned: -5
> > > > [ 743.284184] tda18271_init: error -5 on line 826
> > > > [ 743.284190] tda18271_tune: error -5 on line 904
> > > > [ 743.284194] tda18271_set_params: error -5 on line 985
> > > > [ 744.300169] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
> >i2c_transfer
> >
> >
> > > > returned: -5
> > > > [ 744.300180] tda18271_init: error -5 on line 826
> > > > [ 744.300185] tda18271_tune: error -5 on line 904
> > > > [ 744.300190] tda18271_set_params: error -5 on line 985
> > > > [ 745.320172] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
> >i2c_transfer
> >
> >
> > > > returned: -5
> > > > [ 745.320183] tda18271_init: error -5 on line 826
> > > > [ 745.320188] tda18271_tune: error -5 on line 904
> > > > [ 745.320193] tda18271_set_params: error -5 on line 985
> > > > [ 746.336174] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
> >i2c_transfer
> >
> >
> > > > returned: -5
> > > > [ 746.336185] tda18271_init: error -5 on line 826
> > > > [ 746.336190] tda18271_tune: error -5 on line 904
> > > > [ 746.336195] tda18271_set_params: error -5 on line 985
> > > > [ 747.352170] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
> >i2c_transfer
> >
> >
> > > > returned: -5
> > > > [ 747.352181] tda18271_init: error -5 on line 826
> > > > [ 747.352187] tda18271_tune: error -5 on line 904
> > > > [ 747.352192] tda18271_set_params: error -5 on line 985
> > > > [ 748.368172] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
> >i2c_transfer
> >
> >
> > > > returned: -5
> > > > [ 748.368183] tda18271_init: error -5 on line 826
> > > > [ 748.368188] tda18271_tune: error -5 on line 904
> > > > [ 748.368193] tda18271_set_params: error -5 on line 985
> > > > [ 749.384179] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
> >i2c_transfer
> >
> >
> > > > returned: -5
> > > > [ 749.384191] tda18271_init: error -5 on line 826
> > > > [ 749.384196] tda18271_tune: error -5 on line 904
> > > > [ 749.384202] tda18271_set_params: error -5 on line 985
> > > > [ 750.400172] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
> >i2c_transfer
> >
> >
> > > > returned: -5
> > > > [ 750.400182] tda18271_init: error -5 on line 826
> > > > [ 750.400188] tda18271_tune: error -5 on line 904
> > > > [ 750.400194] tda18271_set_params: error -5 on line 985
> > > > [ 751.424170] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
> >i2c_transfer
> >
> >
> > > > returned: -5
> > > > [ 751.424181] tda18271_init: error -5 on line 826
> > > > [ 751.424186] tda18271_tune: error -5 on line 904
> > > > [ 751.424192] tda18271_set_params: error -5 on line 985
> > > > [ 752.440172] tda18271_write_regs: ERROR: idx = 0x5, len = 1,
> >i2c_transfer
> >
> >
> > > > returned: -5
> > > >
>
>
> >
> >
> > >
> > >
> > > >
> > > >
> > > > Any ideas?
> > > > Thanks
> > > >
> > > >
> > > >
> > > >
> > >
> >
> >
> >
>
>
>
^ permalink raw reply [flat|nested] 13+ messages in thread
end of thread, other threads:[~2011-01-15 17:37 UTC | newest]
Thread overview: 13+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2010-10-11 9:41 Hauppauge WinTV-HVR-1120 on Unbuntu 10.04 fabio tirapelle
2010-10-12 1:00 ` Zhang Rui
2010-10-12 20:27 ` Bjorn Helgaas
2010-10-11 9:57 fabio tirapelle
2010-10-19 18:32 ` Albin Kauffmann
2010-10-19 19:56 ` fabio tirapelle
2010-10-24 14:27 ` Albin Kauffmann
2011-01-11 13:57 ` mmanzato
2011-01-15 17:37 ` Albin Kauffmann
2010-10-13 19:02 fabio tirapelle
2010-10-13 19:54 ` Bjorn Helgaas
2010-10-13 21:26 fabio tirapelle
2010-10-14 12:22 fabio tirapelle
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.