From: Andy Gross <agross@codeaurora.org> To: linux-arm-msm@vger.kernel.org Cc: linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org, Kumar Gala <galak@codeaurora.org>, Stephen Boyd <sboyd@codeaurora.org>, Bjorn Andersson <bjorn.andersson@sonymobile.com>, linux-soc@vger.kernel.org, Andy Gross <agross@codeaurora.org> Subject: [Patch v2 0/6] GSBI CRCI Autoconfiguration Support Date: Fri, 30 Jan 2015 00:25:29 -0600 [thread overview] Message-ID: <1422599135-5588-1-git-send-email-agross@codeaurora.org> (raw) This patch set adds support for automatic configuration of GSBI DMA CRCI values. DMA operations require that the ADM CRCI mux values be properly configured in the TCSR (Top Control and Status Register) block. During probing of a GSBI device, the client mode must be declared and this can be used to lookup the correct TCSR ADM CRCI MUX settings and then program them so that they are correct before any clients are populated. These patches add the TCSR as a syscon device and that allows the GSBI to access and manipulate the ADM CRCI MUX registers to correctly configure the values based on the GSBI port configuration. Changes since v1: - Fixed various review comments Andy Gross (6): soc: qcom: gsbi: Add support for ADM CRCI muxing mfd: qcom,tcsr: Add device tree binding for TCSR ARM: DT: apq8064: Add TCSR support ARM: DT: ipq8064: Add TCSR support ARM: DT: msm8660: Add TCSR support ARM: DT: msm8960: Add TCSR support .../devicetree/bindings/mfd/qcom,tcsr.txt | 22 +++ .../devicetree/bindings/soc/qcom/qcom,gsbi.txt | 18 ++- arch/arm/boot/dts/qcom-apq8064.dtsi | 17 +++ arch/arm/boot/dts/qcom-ipq8064.dtsi | 17 +++ arch/arm/boot/dts/qcom-msm8660.dtsi | 11 ++ arch/arm/boot/dts/qcom-msm8960.dtsi | 11 ++ drivers/soc/qcom/Kconfig | 1 + drivers/soc/qcom/qcom_gsbi.c | 153 ++++++++++++++++++++ 8 files changed, 249 insertions(+), 1 deletion(-) create mode 100644 Documentation/devicetree/bindings/mfd/qcom,tcsr.txt -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, hosted by The Linux Foundation
WARNING: multiple messages have this Message-ID (diff)
From: agross@codeaurora.org (Andy Gross) To: linux-arm-kernel@lists.infradead.org Subject: [Patch v2 0/6] GSBI CRCI Autoconfiguration Support Date: Fri, 30 Jan 2015 00:25:29 -0600 [thread overview] Message-ID: <1422599135-5588-1-git-send-email-agross@codeaurora.org> (raw) This patch set adds support for automatic configuration of GSBI DMA CRCI values. DMA operations require that the ADM CRCI mux values be properly configured in the TCSR (Top Control and Status Register) block. During probing of a GSBI device, the client mode must be declared and this can be used to lookup the correct TCSR ADM CRCI MUX settings and then program them so that they are correct before any clients are populated. These patches add the TCSR as a syscon device and that allows the GSBI to access and manipulate the ADM CRCI MUX registers to correctly configure the values based on the GSBI port configuration. Changes since v1: - Fixed various review comments Andy Gross (6): soc: qcom: gsbi: Add support for ADM CRCI muxing mfd: qcom,tcsr: Add device tree binding for TCSR ARM: DT: apq8064: Add TCSR support ARM: DT: ipq8064: Add TCSR support ARM: DT: msm8660: Add TCSR support ARM: DT: msm8960: Add TCSR support .../devicetree/bindings/mfd/qcom,tcsr.txt | 22 +++ .../devicetree/bindings/soc/qcom/qcom,gsbi.txt | 18 ++- arch/arm/boot/dts/qcom-apq8064.dtsi | 17 +++ arch/arm/boot/dts/qcom-ipq8064.dtsi | 17 +++ arch/arm/boot/dts/qcom-msm8660.dtsi | 11 ++ arch/arm/boot/dts/qcom-msm8960.dtsi | 11 ++ drivers/soc/qcom/Kconfig | 1 + drivers/soc/qcom/qcom_gsbi.c | 153 ++++++++++++++++++++ 8 files changed, 249 insertions(+), 1 deletion(-) create mode 100644 Documentation/devicetree/bindings/mfd/qcom,tcsr.txt -- The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, hosted by The Linux Foundation
next reply other threads:[~2015-01-30 6:25 UTC|newest] Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top 2015-01-30 6:25 Andy Gross [this message] 2015-01-30 6:25 ` [Patch v2 0/6] GSBI CRCI Autoconfiguration Support Andy Gross 2015-01-30 6:25 ` [Patch v2 1/6] soc: qcom: gsbi: Add support for ADM CRCI muxing Andy Gross 2015-01-30 6:25 ` Andy Gross 2015-01-30 6:25 ` Andy Gross 2015-01-30 16:32 ` Kumar Gala 2015-01-30 16:32 ` Kumar Gala [not found] ` <B36DEAB1-2D89-4B6B-991E-C2EDBEB684D9-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org> 2015-01-30 21:37 ` Stephen Boyd 2015-01-30 21:37 ` Stephen Boyd 2015-01-30 21:37 ` Stephen Boyd 2015-01-30 21:48 ` Kumar Gala 2015-01-30 21:48 ` Kumar Gala 2015-02-03 2:05 ` Stephen Boyd 2015-02-03 2:05 ` Stephen Boyd 2015-01-30 6:25 ` [Patch v2 2/6] mfd: qcom,tcsr: Add device tree binding for TCSR Andy Gross 2015-01-30 6:25 ` Andy Gross 2015-01-30 6:25 ` Andy Gross 2015-01-30 6:25 ` [Patch v2 3/6] ARM: DT: apq8064: Add TCSR support Andy Gross 2015-01-30 6:25 ` Andy Gross 2015-01-30 6:25 ` [Patch v2 4/6] ARM: DT: ipq8064: " Andy Gross 2015-01-30 6:25 ` Andy Gross 2015-01-30 6:25 ` [Patch v2 5/6] ARM: DT: msm8660: " Andy Gross 2015-01-30 6:25 ` Andy Gross 2015-01-30 6:25 ` [Patch v2 6/6] ARM: DT: msm8960: " Andy Gross 2015-01-30 6:25 ` Andy Gross
Reply instructions: You may reply publicly to this message via plain-text email using any one of the following methods: * Save the following mbox file, import it into your mail client, and reply-to-all from there: mbox Avoid top-posting and favor interleaved quoting: https://en.wikipedia.org/wiki/Posting_style#Interleaved_style * Reply using the --to, --cc, and --in-reply-to switches of git-send-email(1): git send-email \ --in-reply-to=1422599135-5588-1-git-send-email-agross@codeaurora.org \ --to=agross@codeaurora.org \ --cc=bjorn.andersson@sonymobile.com \ --cc=devicetree@vger.kernel.org \ --cc=galak@codeaurora.org \ --cc=linux-arm-kernel@lists.infradead.org \ --cc=linux-arm-msm@vger.kernel.org \ --cc=linux-kernel@vger.kernel.org \ --cc=linux-soc@vger.kernel.org \ --cc=sboyd@codeaurora.org \ /path/to/YOUR_REPLY https://kernel.org/pub/software/scm/git/docs/git-send-email.html * If your mail client supports setting the In-Reply-To header via mailto: links, try the mailto: linkBe sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.