From: Rob Herring <robh@kernel.org>
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Alan Stern <stern@rowland.harvard.edu>,
Kishon Vijay Abraham I <kishon@ti.com>
Cc: linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
linux-usb@vger.kernel.org, Rob Herring <robh@kernel.org>
Subject: [PATCH 4/5] phy: add Marvell HSIC 28nm PHY
Date: Wed, 13 May 2015 17:48:59 -0500 [thread overview]
Message-ID: <1431557340-5421-5-git-send-email-robh@kernel.org> (raw)
In-Reply-To: <1431557340-5421-1-git-send-email-robh@kernel.org>
Add PHY driver for the Marvell HSIC 28nm PHY. This PHY is found in PXA1928
SOC.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
---
drivers/phy/Kconfig | 10 +++
drivers/phy/Makefile | 1 +
drivers/phy/phy-mv-hsic.c | 208 ++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 219 insertions(+)
create mode 100644 drivers/phy/phy-mv-hsic.c
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index ef7634f..cfcae72 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -52,6 +52,16 @@ config PHY_EXYNOS_MIPI_VIDEO
Support for MIPI CSI-2 and MIPI DSI DPHY found on Samsung S5P
and EXYNOS SoCs.
+config PHY_MV_HSIC
+ tristate "Marvell USB HSIC 28nm PHY Driver"
+ select GENERIC_PHY
+ help
+ Enable this to support Marvell USB HSIC PHY driver for Marvell
+ SoC. This driver will do the PHY initialization and shutdown.
+ The PHY driver will be used by Marvell ehci driver.
+
+ To compile this driver as a module, choose M here.
+
config PHY_MV_USB2
tristate "Marvell USB 2.0 28nm PHY Driver"
select GENERIC_PHY
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index 768e55a..472bf0a 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY) += phy-armada375-usb2.o
obj-$(CONFIG_BCM_KONA_USB2_PHY) += phy-bcm-kona-usb2.o
obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO) += phy-exynos-dp-video.o
obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO) += phy-exynos-mipi-video.o
+obj-$(CONFIG_PHY_MV_HSIC) += phy-mv-hsic.o
obj-$(CONFIG_PHY_MV_USB2) += phy-mv-usb2.o
obj-$(CONFIG_PHY_MVEBU_SATA) += phy-mvebu-sata.o
obj-$(CONFIG_PHY_MIPHY28LP) += phy-miphy28lp.o
diff --git a/drivers/phy/phy-mv-hsic.c b/drivers/phy/phy-mv-hsic.c
new file mode 100644
index 0000000..aa6cccd
--- /dev/null
+++ b/drivers/phy/phy-mv-hsic.c
@@ -0,0 +1,208 @@
+/*
+ * Copyright (C) 2015 Linaro, Ltd.
+ * Rob Herring <robh@kernel.org>
+ *
+ * Based on vendor driver:
+ * Copyright (C) 2013 Marvell Inc.
+ * Author: Chao Xie <xiechao.mail@gmail.com>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/io.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+
+#define PHY_28NM_HSIC_CTRL 0x08
+#define PHY_28NM_HSIC_IMPCAL_CAL 0x18
+#define PHY_28NM_HSIC_PLL_CTRL01 0x1c
+#define PHY_28NM_HSIC_PLL_CTRL2 0x20
+#define PHY_28NM_HSIC_INT 0x28
+
+#define PHY_28NM_HSIC_PLL_SELLPFR_SHIFT 26
+#define PHY_28NM_HSIC_PLL_FBDIV_SHIFT 0
+#define PHY_28NM_HSIC_PLL_REFDIV_SHIFT 9
+
+#define PHY_28NM_HSIC_S2H_PU_PLL BIT(10)
+#define PHY_28NM_HSIC_H2S_PLL_LOCK BIT(15)
+#define PHY_28NM_HSIC_S2H_HSIC_EN BIT(7)
+#define S2H_DRV_SE0_4RESUME BIT(14)
+#define PHY_28NM_HSIC_H2S_IMPCAL_DONE BIT(27)
+
+#define PHY_28NM_HSIC_CONNECT_INT BIT(1)
+#define PHY_28NM_HSIC_HS_READY_INT BIT(2)
+
+struct mv_hsic_phy {
+ struct phy *phy;
+ struct platform_device *pdev;
+ void __iomem *base;
+ struct clk *clk;
+};
+
+static bool wait_for_reg(void __iomem *reg, u32 mask, unsigned long timeout)
+{
+ timeout += jiffies;
+ while (time_is_after_eq_jiffies(timeout)) {
+ if ((readl(reg) & mask) == mask)
+ return true;
+ msleep(1);
+ }
+ return false;
+}
+
+static int mv_hsic_phy_init(struct phy *phy)
+{
+ struct mv_hsic_phy *mv_phy = phy_get_drvdata(phy);
+ struct platform_device *pdev = mv_phy->pdev;
+ void __iomem *base = mv_phy->base;
+
+ clk_prepare_enable(mv_phy->clk);
+
+ /* Set reference clock */
+ writel(0x1 << PHY_28NM_HSIC_PLL_SELLPFR_SHIFT |
+ 0xf0 << PHY_28NM_HSIC_PLL_FBDIV_SHIFT |
+ 0xd << PHY_28NM_HSIC_PLL_REFDIV_SHIFT,
+ base + PHY_28NM_HSIC_PLL_CTRL01);
+
+ /* Turn on PLL */
+ writel(readl(base + PHY_28NM_HSIC_PLL_CTRL2) |
+ PHY_28NM_HSIC_S2H_PU_PLL,
+ base + PHY_28NM_HSIC_PLL_CTRL2);
+
+ /* Make sure PHY PLL is locked */
+ if (!wait_for_reg(base + PHY_28NM_HSIC_PLL_CTRL2,
+ PHY_28NM_HSIC_H2S_PLL_LOCK, HZ / 10)) {
+ dev_err(&pdev->dev, "HSIC PHY PLL not locked after 100mS.");
+ return -ETIMEDOUT;
+ }
+
+ /* Avoid SE0 state when resume for some device will take it as reset */
+ writel(readl(base + PHY_28NM_HSIC_CTRL) & ~S2H_DRV_SE0_4RESUME,
+ base + PHY_28NM_HSIC_CTRL);
+
+ /* Enable HSIC PHY */
+ writel(readl(base + PHY_28NM_HSIC_CTRL) | PHY_28NM_HSIC_S2H_HSIC_EN,
+ base + PHY_28NM_HSIC_CTRL);
+
+ /* Calibration Timing
+ * ____________________________
+ * CAL START ___|
+ * ____________________
+ * CAL_DONE ___________|
+ * | 400us |
+ */
+
+ /* Make sure PHY Calibration is ready */
+ if (!wait_for_reg(base + PHY_28NM_HSIC_IMPCAL_CAL,
+ PHY_28NM_HSIC_H2S_IMPCAL_DONE, HZ / 10)) {
+ dev_warn(&pdev->dev, "HSIC PHY READY not set after 100mS.");
+ return -ETIMEDOUT;
+ }
+
+ /* Waiting for HSIC connect int*/
+ if (!wait_for_reg(base + PHY_28NM_HSIC_INT,
+ PHY_28NM_HSIC_CONNECT_INT, HZ / 5)) {
+ dev_warn(&pdev->dev, "HSIC wait for connect interrupt timeout.");
+ return -ETIMEDOUT;
+ }
+
+ return 0;
+}
+
+static int mv_hsic_phy_power_on(struct phy *phy)
+{
+ struct mv_hsic_phy *mv_phy = phy_get_drvdata(phy);
+ struct platform_device *pdev = mv_phy->pdev;
+
+ /* check HS ready */
+ if (!wait_for_reg(mv_phy->base + PHY_28NM_HSIC_INT,
+ PHY_28NM_HSIC_HS_READY_INT, HZ / 10)) {
+ dev_err(&pdev->dev, "HSIC HS_READY not set\n");
+ return -ETIMEDOUT;
+ }
+ return 0;
+}
+
+static int mv_hsic_phy_power_off(struct phy *phy)
+{
+ struct mv_hsic_phy *mv_phy = phy_get_drvdata(phy);
+ void __iomem *base = mv_phy->base;
+
+ writel(readl(base + PHY_28NM_HSIC_CTRL) & ~PHY_28NM_HSIC_S2H_HSIC_EN,
+ base + PHY_28NM_HSIC_CTRL);
+
+ clk_disable_unprepare(mv_phy->clk);
+ return 0;
+}
+
+static const struct phy_ops hsic_ops = {
+ .init = mv_hsic_phy_init,
+ .power_on = mv_hsic_phy_power_on,
+ .power_off = mv_hsic_phy_power_off,
+};
+
+static int mv_hsic_phy_probe(struct platform_device *pdev)
+{
+ struct phy_provider *phy_provider;
+ struct mv_hsic_phy *mv_phy;
+ struct resource *r;
+
+ mv_phy = devm_kzalloc(&pdev->dev, sizeof(*mv_phy), GFP_KERNEL);
+ if (!mv_phy)
+ return -ENOMEM;
+
+ mv_phy->pdev = pdev;
+
+ mv_phy->clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(mv_phy->clk)) {
+ dev_err(&pdev->dev, "failed to get clock.\n");
+ return PTR_ERR(mv_phy->clk);
+ }
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ mv_phy->base = devm_ioremap_resource(&pdev->dev, r);
+ if (IS_ERR(mv_phy->base))
+ return PTR_ERR(mv_phy->base);
+
+ mv_phy->phy = devm_phy_create(&pdev->dev, pdev->dev.of_node, &hsic_ops);
+ if (IS_ERR(mv_phy->phy))
+ return PTR_ERR(mv_phy->phy);
+
+ phy_set_drvdata(mv_phy->phy, mv_phy);
+
+ phy_provider = devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate);
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id mv_hsic_phy_dt_match[] = {
+ { .compatible = "marvell,pxa1928-hsic-phy", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, mv_hsic_phy_dt_match);
+
+static struct platform_driver mv_hsic_phy_driver = {
+ .probe = mv_hsic_phy_probe,
+ .driver = {
+ .name = "mv-hsic-phy",
+ .of_match_table = of_match_ptr(mv_hsic_phy_dt_match),
+ },
+};
+module_platform_driver(mv_hsic_phy_driver);
+
+MODULE_AUTHOR("Rob Herring <robh@kernel.org>");
+MODULE_DESCRIPTION("Marvell HSIC phy driver");
+MODULE_LICENSE("GPL v2");
--
2.1.0
next prev parent reply other threads:[~2015-05-13 22:49 UTC|newest]
Thread overview: 39+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-05-13 22:48 [PATCH 0/5] Marvell PXA1928 USB support Rob Herring
2015-05-13 22:48 ` Rob Herring
2015-05-13 22:48 ` [PATCH 1/5] dt-bindings: Add Marvell PXA1928 USB and HSIC PHY bindings Rob Herring
2015-05-13 22:48 ` Rob Herring
2015-05-13 22:48 ` [PATCH 2/5] dt-bindings: Add Marvell PXA1928 USB EHCI controller binding Rob Herring
2015-05-13 22:48 ` [PATCH 3/5] phy: Add Marvell USB 2.0 OTG 28nm PHY Rob Herring
2015-05-13 22:48 ` Rob Herring
2015-05-21 12:33 ` Kishon Vijay Abraham I
2015-05-21 12:33 ` Kishon Vijay Abraham I
2015-05-13 22:48 ` Rob Herring [this message]
2015-05-21 12:45 ` [PATCH 4/5] phy: add Marvell HSIC " Kishon Vijay Abraham I
2015-05-21 12:45 ` Kishon Vijay Abraham I
2015-05-21 12:51 ` Kishon Vijay Abraham I
2015-05-21 12:51 ` Kishon Vijay Abraham I
2015-05-22 19:54 ` Rob Herring
2015-05-22 19:54 ` Rob Herring
2015-05-26 6:06 ` Kishon Vijay Abraham I
2015-05-13 22:49 ` [PATCH 5/5] usb: add pxa1928 ehci support Rob Herring
2015-05-14 8:24 ` Paul Bolle
2015-05-14 10:42 ` Arnd Bergmann
2015-05-14 13:25 ` Rob Herring
2015-05-14 13:25 ` Rob Herring
2015-05-14 10:43 ` Arnd Bergmann
2015-05-14 14:56 ` Alan Stern
2015-05-14 14:56 ` Alan Stern
2015-05-14 16:36 ` Rob Herring
2015-05-14 16:36 ` Rob Herring
2015-05-14 17:06 ` Alan Stern
2015-05-14 17:06 ` Alan Stern
2015-05-14 15:55 ` Alan Stern
2015-05-14 15:55 ` Alan Stern
2015-05-15 9:32 ` Arnd Bergmann
2015-05-15 9:55 ` [PATCH 0/5] Marvell PXA1928 USB support Sebastian Hesselbarth
2015-05-15 9:55 ` Sebastian Hesselbarth
2015-05-15 12:48 ` Rob Herring
2015-05-15 12:48 ` Rob Herring
2015-05-15 14:11 ` Arnd Bergmann
2015-05-15 16:04 ` Rob Herring
2015-05-15 16:04 ` Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1431557340-5421-5-git-send-email-robh@kernel.org \
--to=robh@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=kishon@ti.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=stern@rowland.harvard.edu \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.