[PATCH 0/5] ARM: dts: sunxi: Add backlight node to q8 tablets

[PATCH 0/5] ARM: dts: sunxi: Add backlight node to q8 tablets

[Hans de Goede]

Hi Maxime, Chen-Yu,

Here is a slightly updated version of Chen-Yu's backlight
patches, also adding support for the backlight found on A13 
based q8 tablets.

This series is based on mripard/sunxi/for-next with the following
patches on top (Maxime you've send mails indicating that you've merged
these alread, but you seem to have not pushed them yet) :

ARM: dts: sun5i: Add sun5i-q8-common.dtsi
ARM: dts: sun5i: Add dts file for q8 formfactor a13 based tablets
ARM: dts: sun8i: Add PWM controller node for A23/A33
ARM: dts: sun8i: Add PWM channel 0 pinmux setting for A23/A33

As discussed I've changed the "ARM: dts: sunxi: Enable PWM controller
on Q8 format tablets" patch to enable the pwm node in sunxi-q8-common.h
rather then in sunx8i-q8-common.h, other then that the 2 patches from
Chen-Yu are unchanged.

Regards,

Hans

[PATCH 0/5] ARM: dts: sunxi: Add backlight node to q8 tablets

[Hans de Goede]

Hi Maxime, Chen-Yu,

Here is a slightly updated version of Chen-Yu's backlight
patches, also adding support for the backlight found on A13 
based q8 tablets.

This series is based on mripard/sunxi/for-next with the following
patches on top (Maxime you've send mails indicating that you've merged
these alread, but you seem to have not pushed them yet) :

ARM: dts: sun5i: Add sun5i-q8-common.dtsi
ARM: dts: sun5i: Add dts file for q8 formfactor a13 based tablets
ARM: dts: sun8i: Add PWM controller node for A23/A33
ARM: dts: sun8i: Add PWM channel 0 pinmux setting for A23/A33

As discussed I've changed the "ARM: dts: sunxi: Enable PWM controller
on Q8 format tablets" patch to enable the pwm node in sunxi-q8-common.h
rather then in sunx8i-q8-common.h, other then that the 2 patches from
Chen-Yu are unchanged.

Regards,

Hans

[PATCH 1/5] ARM: dts: sun5i: Add PWM controller node for A13/A10s

[Hans de Goede]

The sun5i die has a PWM controller that is compatible to the one on the A20.
Add a device node for it.

Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
---
 arch/arm/boot/dts/sun5i.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/sun5i.dtsi b/arch/arm/boot/dts/sun5i.dtsi
index 78b993a..5e036a4 100644
--- a/arch/arm/boot/dts/sun5i.dtsi
+++ b/arch/arm/boot/dts/sun5i.dtsi
@@ -543,6 +543,14 @@
 			reg = <0x01c20c90 0x10>;
 		};
 
+		pwm: pwm@01c20e00 {
+			compatible = "allwinner,sun7i-a20-pwm";
+			reg = <0x01c20e00 0xc>;
+			clocks = <&osc24M>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
 		lradc: lradc@01c22800 {
 			compatible = "allwinner,sun4i-a10-lradc-keys";
 			reg = <0x01c22800 0x100>;
-- 
2.4.3

[PATCH 1/5] ARM: dts: sun5i: Add PWM controller node for A13/A10s

[Hans de Goede]

The sun5i die has a PWM controller that is compatible to the one on the A20.
Add a device node for it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 arch/arm/boot/dts/sun5i.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/boot/dts/sun5i.dtsi b/arch/arm/boot/dts/sun5i.dtsi
index 78b993a..5e036a4 100644
--- a/arch/arm/boot/dts/sun5i.dtsi
+++ b/arch/arm/boot/dts/sun5i.dtsi
@@ -543,6 +543,14 @@
 			reg = <0x01c20c90 0x10>;
 		};
 
+		pwm: pwm at 01c20e00 {
+			compatible = "allwinner,sun7i-a20-pwm";
+			reg = <0x01c20e00 0xc>;
+			clocks = <&osc24M>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
 		lradc: lradc at 01c22800 {
 			compatible = "allwinner,sun4i-a10-lradc-keys";
 			reg = <0x01c22800 0x100>;
-- 
2.4.3

Re: [PATCH 1/5] ARM: dts: sun5i: Add PWM controller node for A13/A10s

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 839 bytes --]

On Sun, Sep 20, 2015 at 08:30:47AM -0400, Hans de Goede wrote:
> The sun5i die has a PWM controller that is compatible to the one on the A20.
> Add a device node for it.
> 
> Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
> ---
>  arch/arm/boot/dts/sun5i.dtsi | 8 ++++++++
>  1 file changed, 8 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/sun5i.dtsi b/arch/arm/boot/dts/sun5i.dtsi
> index 78b993a..5e036a4 100644
> --- a/arch/arm/boot/dts/sun5i.dtsi
> +++ b/arch/arm/boot/dts/sun5i.dtsi
> @@ -543,6 +543,14 @@
>  			reg = <0x01c20c90 0x10>;
>  		};
>  
> +		pwm: pwm@01c20e00 {
> +			compatible = "allwinner,sun7i-a20-pwm";

Is it? IIRC, it has a single channel, while the A20 has two.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[PATCH 1/5] ARM: dts: sun5i: Add PWM controller node for A13/A10s

[Maxime Ripard]

On Sun, Sep 20, 2015 at 08:30:47AM -0400, Hans de Goede wrote:
> The sun5i die has a PWM controller that is compatible to the one on the A20.
> Add a device node for it.
> 
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
>  arch/arm/boot/dts/sun5i.dtsi | 8 ++++++++
>  1 file changed, 8 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/sun5i.dtsi b/arch/arm/boot/dts/sun5i.dtsi
> index 78b993a..5e036a4 100644
> --- a/arch/arm/boot/dts/sun5i.dtsi
> +++ b/arch/arm/boot/dts/sun5i.dtsi
> @@ -543,6 +543,14 @@
>  			reg = <0x01c20c90 0x10>;
>  		};
>  
> +		pwm: pwm at 01c20e00 {
> +			compatible = "allwinner,sun7i-a20-pwm";

Is it? IIRC, it has a single channel, while the A20 has two.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150922/25c630ac/attachment.sig>

[PATCH 2/5] ARM: dts: sun5i: Add PWM channel 0 pinmux setting for A13/A10s

[Hans de Goede]

Add a pinmux setting for the first pwm channel. This is often used for
backlight dimming on tablets.

Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
---
 arch/arm/boot/dts/sun5i.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/sun5i.dtsi b/arch/arm/boot/dts/sun5i.dtsi
index 5e036a4..f0714d3 100644
--- a/arch/arm/boot/dts/sun5i.dtsi
+++ b/arch/arm/boot/dts/sun5i.dtsi
@@ -529,6 +529,13 @@
 				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
 				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 			};
+
+			pwm0_pins: pwm0 {
+				allwinner,pins = "PB2";
+				allwinner,function = "pwm";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
 		};
 
 		timer@01c20c00 {
-- 
2.4.3

[PATCH 2/5] ARM: dts: sun5i: Add PWM channel 0 pinmux setting for A13/A10s

[Hans de Goede]

Add a pinmux setting for the first pwm channel. This is often used for
backlight dimming on tablets.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 arch/arm/boot/dts/sun5i.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/sun5i.dtsi b/arch/arm/boot/dts/sun5i.dtsi
index 5e036a4..f0714d3 100644
--- a/arch/arm/boot/dts/sun5i.dtsi
+++ b/arch/arm/boot/dts/sun5i.dtsi
@@ -529,6 +529,13 @@
 				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
 				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 			};
+
+			pwm0_pins: pwm0 {
+				allwinner,pins = "PB2";
+				allwinner,function = "pwm";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
 		};
 
 		timer at 01c20c00 {
-- 
2.4.3

Re: [PATCH 2/5] ARM: dts: sun5i: Add PWM channel 0 pinmux setting for A13/A10s

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 897 bytes --]

On Sun, Sep 20, 2015 at 08:30:48AM -0400, Hans de Goede wrote:
> Add a pinmux setting for the first pwm channel. This is often used for
> backlight dimming on tablets.
> 
> Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
> ---
>  arch/arm/boot/dts/sun5i.dtsi | 7 +++++++
>  1 file changed, 7 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/sun5i.dtsi b/arch/arm/boot/dts/sun5i.dtsi
> index 5e036a4..f0714d3 100644
> --- a/arch/arm/boot/dts/sun5i.dtsi
> +++ b/arch/arm/boot/dts/sun5i.dtsi
> @@ -529,6 +529,13 @@
>  				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
>  				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
>  			};
> +
> +			pwm0_pins: pwm0 {

Is there a reason why you call this pinset pwm0, while it looks like
there's a single pwm controller?

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[PATCH 2/5] ARM: dts: sun5i: Add PWM channel 0 pinmux setting for A13/A10s

[Maxime Ripard]

On Sun, Sep 20, 2015 at 08:30:48AM -0400, Hans de Goede wrote:
> Add a pinmux setting for the first pwm channel. This is often used for
> backlight dimming on tablets.
> 
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
>  arch/arm/boot/dts/sun5i.dtsi | 7 +++++++
>  1 file changed, 7 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/sun5i.dtsi b/arch/arm/boot/dts/sun5i.dtsi
> index 5e036a4..f0714d3 100644
> --- a/arch/arm/boot/dts/sun5i.dtsi
> +++ b/arch/arm/boot/dts/sun5i.dtsi
> @@ -529,6 +529,13 @@
>  				allwinner,drive = <SUN4I_PINCTRL_30_MA>;
>  				allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
>  			};
> +
> +			pwm0_pins: pwm0 {

Is there a reason why you call this pinset pwm0, while it looks like
there's a single pwm controller?

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150922/86ee2f9f/attachment.sig>

[PATCH 3/5] ARM: dts: sunxi: Enable PWM controller on Q8 format tablets

[Hans de Goede]

From: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>

Q8 format tablets use channel 0 of the PWM controller for backlight dimming.

Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
---
Changes in v2:
-Enable the pwm controller in sunxi-q8-common.dtsi rather then in
 sun8i-q8-common.dtsi
---
 arch/arm/boot/dts/sunxi-q8-common.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/sunxi-q8-common.dtsi b/arch/arm/boot/dts/sunxi-q8-common.dtsi
index 17b26ff..b824146 100644
--- a/arch/arm/boot/dts/sunxi-q8-common.dtsi
+++ b/arch/arm/boot/dts/sunxi-q8-common.dtsi
@@ -75,3 +75,9 @@
 		voltage = <400000>;
 	};
 };
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pins>;
+	status = "okay";
+};
-- 
2.4.3

[PATCH 3/5] ARM: dts: sunxi: Enable PWM controller on Q8 format tablets

[Hans de Goede]

From: Chen-Yu Tsai <wens@csie.org>

Q8 format tablets use channel 0 of the PWM controller for backlight dimming.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
Changes in v2:
-Enable the pwm controller in sunxi-q8-common.dtsi rather then in
 sun8i-q8-common.dtsi
---
 arch/arm/boot/dts/sunxi-q8-common.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/boot/dts/sunxi-q8-common.dtsi b/arch/arm/boot/dts/sunxi-q8-common.dtsi
index 17b26ff..b824146 100644
--- a/arch/arm/boot/dts/sunxi-q8-common.dtsi
+++ b/arch/arm/boot/dts/sunxi-q8-common.dtsi
@@ -75,3 +75,9 @@
 		voltage = <400000>;
 	};
 };
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pins>;
+	status = "okay";
+};
-- 
2.4.3

[PATCH 4/5] ARM: dts: sun8i: Add pwm-backlight device for A23/A33 Q8 format tablets

[Hans de Goede]

From: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>

The LCD backlight on the A23/A33 Q8 format tablets is enabled
with a GPIO controlled regulator, and brightness controlled with
the SoC's PWM controller.

The backlight is powered from the AXP223 PMIC's DC1SW output,
which is not supported yet. A proper bootloader is required
to enable it.

The brightness levels are arbitrary. The FEX files do not have
such information. As such, actual brightness levels may differ
from device to device.

Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
---
 arch/arm/boot/dts/sun8i-q8-common.dtsi | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-q8-common.dtsi b/arch/arm/boot/dts/sun8i-q8-common.dtsi
index 6f8a8bb..f342736 100644
--- a/arch/arm/boot/dts/sun8i-q8-common.dtsi
+++ b/arch/arm/boot/dts/sun8i-q8-common.dtsi
@@ -41,11 +41,24 @@
  */
 #include "sunxi-q8-common.dtsi"
 
+#include <dt-bindings/pwm/pwm.h>
+
 / {
 	aliases {
 		serial0 = &r_uart;
 	};
 
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bl_en_pin_q8>;
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+		enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+		/* backlight is powered by AXP223 DC1SW */
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
@@ -62,6 +75,13 @@
 };
 
 &pio {
+	bl_en_pin_q8: bl_en_pin@0 {
+		allwinner,pins = "PH6";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
 	mmc0_cd_pin_q8: mmc0_cd_pin@0 {
 		allwinner,pins = "PB4";
 		allwinner,function = "gpio_in";
-- 
2.4.3

[PATCH 4/5] ARM: dts: sun8i: Add pwm-backlight device for A23/A33 Q8 format tablets

[Hans de Goede]

From: Chen-Yu Tsai <wens@csie.org>

The LCD backlight on the A23/A33 Q8 format tablets is enabled
with a GPIO controlled regulator, and brightness controlled with
the SoC's PWM controller.

The backlight is powered from the AXP223 PMIC's DC1SW output,
which is not supported yet. A proper bootloader is required
to enable it.

The brightness levels are arbitrary. The FEX files do not have
such information. As such, actual brightness levels may differ
from device to device.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 arch/arm/boot/dts/sun8i-q8-common.dtsi | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-q8-common.dtsi b/arch/arm/boot/dts/sun8i-q8-common.dtsi
index 6f8a8bb..f342736 100644
--- a/arch/arm/boot/dts/sun8i-q8-common.dtsi
+++ b/arch/arm/boot/dts/sun8i-q8-common.dtsi
@@ -41,11 +41,24 @@
  */
 #include "sunxi-q8-common.dtsi"
 
+#include <dt-bindings/pwm/pwm.h>
+
 / {
 	aliases {
 		serial0 = &r_uart;
 	};
 
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bl_en_pin_q8>;
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+		enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+		/* backlight is powered by AXP223 DC1SW */
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
@@ -62,6 +75,13 @@
 };
 
 &pio {
+	bl_en_pin_q8: bl_en_pin at 0 {
+		allwinner,pins = "PH6";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
 	mmc0_cd_pin_q8: mmc0_cd_pin at 0 {
 		allwinner,pins = "PB4";
 		allwinner,function = "gpio_in";
-- 
2.4.3

Re: [PATCH 4/5] ARM: dts: sun8i: Add pwm-backlight device for A23/A33 Q8 format tablets

[Maxime Ripard]

[-- Attachment #1: Type: text/plain, Size: 869 bytes --]

On Sun, Sep 20, 2015 at 08:30:50AM -0400, Hans de Goede wrote:
> From: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
> 
> The LCD backlight on the A23/A33 Q8 format tablets is enabled
> with a GPIO controlled regulator, and brightness controlled with
> the SoC's PWM controller.
> 
> The backlight is powered from the AXP223 PMIC's DC1SW output,
> which is not supported yet. A proper bootloader is required
> to enable it.
> 
> The brightness levels are arbitrary. The FEX files do not have
> such information. As such, actual brightness levels may differ
> from device to device.
> 
> Signed-off-by: Chen-Yu Tsai <wens-jdAy2FN1RRM@public.gmane.org>
> Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>

Applied, thanks!

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com

[PATCH 4/5] ARM: dts: sun8i: Add pwm-backlight device for A23/A33 Q8 format tablets

[Maxime Ripard]

On Sun, Sep 20, 2015 at 08:30:50AM -0400, Hans de Goede wrote:
> From: Chen-Yu Tsai <wens@csie.org>
> 
> The LCD backlight on the A23/A33 Q8 format tablets is enabled
> with a GPIO controlled regulator, and brightness controlled with
> the SoC's PWM controller.
> 
> The backlight is powered from the AXP223 PMIC's DC1SW output,
> which is not supported yet. A proper bootloader is required
> to enable it.
> 
> The brightness levels are arbitrary. The FEX files do not have
> such information. As such, actual brightness levels may differ
> from device to device.
> 
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>

Applied, thanks!

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux, Kernel and Android engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20150922/44c0da5a/attachment.sig>

[PATCH 5/5] ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsi

[Hans de Goede]

All A13 based q8 formfactor tablets use the same backlight setup, add
a backlight devicetree node for controlling the backlight on these devices.

Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
---
 arch/arm/boot/dts/sun5i-q8-common.dtsi | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/arch/arm/boot/dts/sun5i-q8-common.dtsi b/arch/arm/boot/dts/sun5i-q8-common.dtsi
index 0641d68..76a5204 100644
--- a/arch/arm/boot/dts/sun5i-q8-common.dtsi
+++ b/arch/arm/boot/dts/sun5i-q8-common.dtsi
@@ -41,11 +41,22 @@
  */
 #include "sunxi-q8-common.dtsi"
 
+#include <dt-bindings/pwm/pwm.h>
+
 / {
 	aliases {
 		serial0 = &uart1;
 	};
 
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+		/* TODO: backlight uses axp gpio1 as enable pin */
+		/* TODO: backlight is powered by AXP209 DCDC1SW */
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
-- 
2.4.3

[PATCH 5/5] ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsi

[Hans de Goede]

All A13 based q8 formfactor tablets use the same backlight setup, add
a backlight devicetree node for controlling the backlight on these devices.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 arch/arm/boot/dts/sun5i-q8-common.dtsi | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/arch/arm/boot/dts/sun5i-q8-common.dtsi b/arch/arm/boot/dts/sun5i-q8-common.dtsi
index 0641d68..76a5204 100644
--- a/arch/arm/boot/dts/sun5i-q8-common.dtsi
+++ b/arch/arm/boot/dts/sun5i-q8-common.dtsi
@@ -41,11 +41,22 @@
  */
 #include "sunxi-q8-common.dtsi"
 
+#include <dt-bindings/pwm/pwm.h>
+
 / {
 	aliases {
 		serial0 = &uart1;
 	};
 
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+		default-brightness-level = <8>;
+		/* TODO: backlight uses axp gpio1 as enable pin */
+		/* TODO: backlight is powered by AXP209 DCDC1SW */
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
-- 
2.4.3

Re: [PATCH 5/5] ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsi

[Chen-Yu Tsai]

On Sun, Sep 20, 2015 at 8:30 PM, Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> wrote:
> All A13 based q8 formfactor tablets use the same backlight setup, add
> a backlight devicetree node for controlling the backlight on these devices.
>
> Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
> ---
>  arch/arm/boot/dts/sun5i-q8-common.dtsi | 11 +++++++++++
>  1 file changed, 11 insertions(+)
>
> diff --git a/arch/arm/boot/dts/sun5i-q8-common.dtsi b/arch/arm/boot/dts/sun5i-q8-common.dtsi
> index 0641d68..76a5204 100644
> --- a/arch/arm/boot/dts/sun5i-q8-common.dtsi
> +++ b/arch/arm/boot/dts/sun5i-q8-common.dtsi
> @@ -41,11 +41,22 @@
>   */
>  #include "sunxi-q8-common.dtsi"
>
> +#include <dt-bindings/pwm/pwm.h>
> +
>  / {
>         aliases {
>                 serial0 = &uart1;
>         };
>
> +       backlight: backlight {
> +               compatible = "pwm-backlight";
> +               pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
> +               brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
> +               default-brightness-level = <8>;
> +               /* TODO: backlight uses axp gpio1 as enable pin */
> +               /* TODO: backlight is powered by AXP209 DCDC1SW */

There's no DCDC1SW on AXP209. The reference design shows the backlight
regulator is powered directly from IPSOUT, but the PWM pullup is powered
by LCD-VCC, which itself is enabled by AXP209 GPIO0.

Would that be the case, or maybe closer, given we don't have schematics?


Regards
ChenYu

> +       };
> +
>         chosen {
>                 stdout-path = "serial0:115200n8";
>         };
> --
> 2.4.3
>

[PATCH 5/5] ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsi

[Chen-Yu Tsai]

On Sun, Sep 20, 2015 at 8:30 PM, Hans de Goede <hdegoede@redhat.com> wrote:
> All A13 based q8 formfactor tablets use the same backlight setup, add
> a backlight devicetree node for controlling the backlight on these devices.
>
> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
> ---
>  arch/arm/boot/dts/sun5i-q8-common.dtsi | 11 +++++++++++
>  1 file changed, 11 insertions(+)
>
> diff --git a/arch/arm/boot/dts/sun5i-q8-common.dtsi b/arch/arm/boot/dts/sun5i-q8-common.dtsi
> index 0641d68..76a5204 100644
> --- a/arch/arm/boot/dts/sun5i-q8-common.dtsi
> +++ b/arch/arm/boot/dts/sun5i-q8-common.dtsi
> @@ -41,11 +41,22 @@
>   */
>  #include "sunxi-q8-common.dtsi"
>
> +#include <dt-bindings/pwm/pwm.h>
> +
>  / {
>         aliases {
>                 serial0 = &uart1;
>         };
>
> +       backlight: backlight {
> +               compatible = "pwm-backlight";
> +               pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
> +               brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
> +               default-brightness-level = <8>;
> +               /* TODO: backlight uses axp gpio1 as enable pin */
> +               /* TODO: backlight is powered by AXP209 DCDC1SW */

There's no DCDC1SW on AXP209. The reference design shows the backlight
regulator is powered directly from IPSOUT, but the PWM pullup is powered
by LCD-VCC, which itself is enabled by AXP209 GPIO0.

Would that be the case, or maybe closer, given we don't have schematics?


Regards
ChenYu

> +       };
> +
>         chosen {
>                 stdout-path = "serial0:115200n8";
>         };
> --
> 2.4.3
>

Re: Re: [PATCH 5/5] ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsi

[Hans de Goede]

Hi,

On 09/20/2015 10:46 AM, Chen-Yu Tsai wrote:
> On Sun, Sep 20, 2015 at 8:30 PM, Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> wrote:
>> All A13 based q8 formfactor tablets use the same backlight setup, add
>> a backlight devicetree node for controlling the backlight on these devices.
>>
>> Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
>> ---
>>   arch/arm/boot/dts/sun5i-q8-common.dtsi | 11 +++++++++++
>>   1 file changed, 11 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/sun5i-q8-common.dtsi b/arch/arm/boot/dts/sun5i-q8-common.dtsi
>> index 0641d68..76a5204 100644
>> --- a/arch/arm/boot/dts/sun5i-q8-common.dtsi
>> +++ b/arch/arm/boot/dts/sun5i-q8-common.dtsi
>> @@ -41,11 +41,22 @@
>>    */
>>   #include "sunxi-q8-common.dtsi"
>>
>> +#include <dt-bindings/pwm/pwm.h>
>> +
>>   / {
>>          aliases {
>>                  serial0 = &uart1;
>>          };
>>
>> +       backlight: backlight {
>> +               compatible = "pwm-backlight";
>> +               pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
>> +               brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
>> +               default-brightness-level = <8>;
>> +               /* TODO: backlight uses axp gpio1 as enable pin */
>> +               /* TODO: backlight is powered by AXP209 DCDC1SW */
>
> There's no DCDC1SW on AXP209. The reference design shows the backlight
> regulator is powered directly from IPSOUT,

Ah, right, I'll do a v2 dropping this comment line.

 > but the PWM pullup is powered
> by LCD-VCC,  which itself is enabled by AXP209 GPIO0.
>
> Would that be the case, or maybe closer, given we don't have schematics?

gpio0 needs to be driven high to get the backlight to lite up, that
is pretty much all I know.

Regards,

Hans

[linux-sunxi] Re: [PATCH 5/5] ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsi

[Hans de Goede]

Hi,

On 09/20/2015 10:46 AM, Chen-Yu Tsai wrote:
> On Sun, Sep 20, 2015 at 8:30 PM, Hans de Goede <hdegoede@redhat.com> wrote:
>> All A13 based q8 formfactor tablets use the same backlight setup, add
>> a backlight devicetree node for controlling the backlight on these devices.
>>
>> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
>> ---
>>   arch/arm/boot/dts/sun5i-q8-common.dtsi | 11 +++++++++++
>>   1 file changed, 11 insertions(+)
>>
>> diff --git a/arch/arm/boot/dts/sun5i-q8-common.dtsi b/arch/arm/boot/dts/sun5i-q8-common.dtsi
>> index 0641d68..76a5204 100644
>> --- a/arch/arm/boot/dts/sun5i-q8-common.dtsi
>> +++ b/arch/arm/boot/dts/sun5i-q8-common.dtsi
>> @@ -41,11 +41,22 @@
>>    */
>>   #include "sunxi-q8-common.dtsi"
>>
>> +#include <dt-bindings/pwm/pwm.h>
>> +
>>   / {
>>          aliases {
>>                  serial0 = &uart1;
>>          };
>>
>> +       backlight: backlight {
>> +               compatible = "pwm-backlight";
>> +               pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
>> +               brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
>> +               default-brightness-level = <8>;
>> +               /* TODO: backlight uses axp gpio1 as enable pin */
>> +               /* TODO: backlight is powered by AXP209 DCDC1SW */
>
> There's no DCDC1SW on AXP209. The reference design shows the backlight
> regulator is powered directly from IPSOUT,

Ah, right, I'll do a v2 dropping this comment line.

 > but the PWM pullup is powered
> by LCD-VCC,  which itself is enabled by AXP209 GPIO0.
>
> Would that be the case, or maybe closer, given we don't have schematics?

gpio0 needs to be driven high to get the backlight to lite up, that
is pretty much all I know.

Regards,

Hans

Re: Re: [PATCH 5/5] ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsi

[Hans de Goede]

Hi,

On 09/20/2015 11:14 AM, Hans de Goede wrote:
> Hi,
>
> On 09/20/2015 10:46 AM, Chen-Yu Tsai wrote:
>> On Sun, Sep 20, 2015 at 8:30 PM, Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org> wrote:
>>> All A13 based q8 formfactor tablets use the same backlight setup, add
>>> a backlight devicetree node for controlling the backlight on these devices.
>>>
>>> Signed-off-by: Hans de Goede <hdegoede-H+wXaHxf7aLQT0dZR+AlfA@public.gmane.org>
>>> ---
>>>   arch/arm/boot/dts/sun5i-q8-common.dtsi | 11 +++++++++++
>>>   1 file changed, 11 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/sun5i-q8-common.dtsi b/arch/arm/boot/dts/sun5i-q8-common.dtsi
>>> index 0641d68..76a5204 100644
>>> --- a/arch/arm/boot/dts/sun5i-q8-common.dtsi
>>> +++ b/arch/arm/boot/dts/sun5i-q8-common.dtsi
>>> @@ -41,11 +41,22 @@
>>>    */
>>>   #include "sunxi-q8-common.dtsi"
>>>
>>> +#include <dt-bindings/pwm/pwm.h>
>>> +
>>>   / {
>>>          aliases {
>>>                  serial0 = &uart1;
>>>          };
>>>
>>> +       backlight: backlight {
>>> +               compatible = "pwm-backlight";
>>> +               pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
>>> +               brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
>>> +               default-brightness-level = <8>;
>>> +               /* TODO: backlight uses axp gpio1 as enable pin */
>>> +               /* TODO: backlight is powered by AXP209 DCDC1SW */
>>
>> There's no DCDC1SW on AXP209. The reference design shows the backlight
>> regulator is powered directly from IPSOUT,
>
> Ah, right, I'll do a v2 dropping this comment line.
>
>  > but the PWM pullup is powered
>> by LCD-VCC,  which itself is enabled by AXP209 GPIO0.
>>
>> Would that be the case, or maybe closer, given we don't have schematics?
>
> gpio0 needs to be driven high to get the backlight to lite up, that
> is pretty much all I know.

Correction, gpio1. I guess that pullup is only there to keep the backlight
off while the pwm pin is still muxed as input, rather then pwm-output.

Regards,

Hans

[linux-sunxi] Re: [PATCH 5/5] ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsi

[Hans de Goede]

Hi,

On 09/20/2015 11:14 AM, Hans de Goede wrote:
> Hi,
>
> On 09/20/2015 10:46 AM, Chen-Yu Tsai wrote:
>> On Sun, Sep 20, 2015 at 8:30 PM, Hans de Goede <hdegoede@redhat.com> wrote:
>>> All A13 based q8 formfactor tablets use the same backlight setup, add
>>> a backlight devicetree node for controlling the backlight on these devices.
>>>
>>> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
>>> ---
>>>   arch/arm/boot/dts/sun5i-q8-common.dtsi | 11 +++++++++++
>>>   1 file changed, 11 insertions(+)
>>>
>>> diff --git a/arch/arm/boot/dts/sun5i-q8-common.dtsi b/arch/arm/boot/dts/sun5i-q8-common.dtsi
>>> index 0641d68..76a5204 100644
>>> --- a/arch/arm/boot/dts/sun5i-q8-common.dtsi
>>> +++ b/arch/arm/boot/dts/sun5i-q8-common.dtsi
>>> @@ -41,11 +41,22 @@
>>>    */
>>>   #include "sunxi-q8-common.dtsi"
>>>
>>> +#include <dt-bindings/pwm/pwm.h>
>>> +
>>>   / {
>>>          aliases {
>>>                  serial0 = &uart1;
>>>          };
>>>
>>> +       backlight: backlight {
>>> +               compatible = "pwm-backlight";
>>> +               pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
>>> +               brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
>>> +               default-brightness-level = <8>;
>>> +               /* TODO: backlight uses axp gpio1 as enable pin */
>>> +               /* TODO: backlight is powered by AXP209 DCDC1SW */
>>
>> There's no DCDC1SW on AXP209. The reference design shows the backlight
>> regulator is powered directly from IPSOUT,
>
> Ah, right, I'll do a v2 dropping this comment line.
>
>  > but the PWM pullup is powered
>> by LCD-VCC,  which itself is enabled by AXP209 GPIO0.
>>
>> Would that be the case, or maybe closer, given we don't have schematics?
>
> gpio0 needs to be driven high to get the backlight to lite up, that
> is pretty much all I know.

Correction, gpio1. I guess that pullup is only there to keep the backlight
off while the pwm pin is still muxed as input, rather then pwm-output.

Regards,

Hans

Re: [PATCH 5/5] ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsi

[8001010]

[-- Attachment #1: Type: text/plain, Size: 74 bytes --]

> +		default-brightness-level = <8>;


Why?
Is not better 100% ?

Silviop

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 5/5] ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsi

[8001010 at gmail.com]

> +		default-brightness-level = <8>;


Why?
Is not better 100% ?

Silviop

Re: [PATCH 5/5] ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsi

[Chen-Yu Tsai]

On Sat, Dec 19, 2015 at 6:54 PM,  <8001010-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:
>> +             default-brightness-level = <8>;
>
>
> Why?
> Is not better 100% ?

It's just an arbitrary value. Plus having the backlight at 100% on battery
powered devices might eat up the battery quicker.

ChenYu

[PATCH 5/5] ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsi

[Chen-Yu Tsai]

On Sat, Dec 19, 2015 at 6:54 PM,  <8001010@gmail.com> wrote:
>> +             default-brightness-level = <8>;
>
>
> Why?
> Is not better 100% ?

It's just an arbitrary value. Plus having the backlight at 100% on battery
powered devices might eat up the battery quicker.

ChenYu

Re: [PATCH 0/5] ARM: dts: sunxi: Add backlight node to q8 tablets

[Silvio Pellicano]

[-- Attachment #1.1: Type: text/plain, Size: 749 bytes --]



> Here is a slightly updated version of Chen-Yu's backlight 
> patches, also adding support for the backlight found on A13 
> based q8 tablets. 
>

If i compile your dtsi with (obviously) pwm  support enable , backlight 
switch off after kernel start, 
if i disable pwm in menuconfig,it stay on, all seem correct (pwm on PB2 in 
original script.bin),
but there is somewhere a bug in pwm or dtsi description of backlight.

Silviop

-- 
You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe-/JYPxA39Uh5TLH3MbocFF+G/Ez6ZCGd0@public.gmane.org
For more options, visit https://groups.google.com/d/optout.

[-- Attachment #1.2: Type: text/html, Size: 1115 bytes --]

Re: Re: [PATCH 0/5] ARM: dts: sunxi: Add backlight node to q8 tablets

[Hans de Goede]

Hi,

On 21-12-15 11:56, Silvio Pellicano wrote:
>
>
>> Here is a slightly updated version of Chen-Yu's backlight
>> patches, also adding support for the backlight found on A13
>> based q8 tablets.
>>
>
> If i compile your dtsi with (obviously) pwm  support enable , backlight
> switch off after kernel start,
> if i disable pwm in menuconfig,it stay on, all seem correct (pwm on PB2 in
> original script.bin),
> but there is somewhere a bug in pwm or dtsi description of backlight.

No there is not, if you enable the pwm driver you must also enable
the backlight-pwm driver / add CONFIG_BACKLIGHT_PWM=y to your .config
(and make sure it stays that way after a "make oldconfig").

Regards,

Hans

[linux-sunxi] Re: [PATCH 0/5] ARM: dts: sunxi: Add backlight node to q8 tablets

[Hans de Goede]

Hi,

On 21-12-15 11:56, Silvio Pellicano wrote:
>
>
>> Here is a slightly updated version of Chen-Yu's backlight
>> patches, also adding support for the backlight found on A13
>> based q8 tablets.
>>
>
> If i compile your dtsi with (obviously) pwm  support enable , backlight
> switch off after kernel start,
> if i disable pwm in menuconfig,it stay on, all seem correct (pwm on PB2 in
> original script.bin),
> but there is somewhere a bug in pwm or dtsi description of backlight.

No there is not, if you enable the pwm driver you must also enable
the backlight-pwm driver / add CONFIG_BACKLIGHT_PWM=y to your .config
(and make sure it stays that way after a "make oldconfig").

Regards,

Hans

Re: Re: [PATCH 0/5] ARM: dts: sunxi: Add backlight node to q8 tablets

[Silvio Pellicano]

[-- Attachment #1.1: Type: text/plain, Size: 276 bytes --]


>
> the backlight-pwm driver / add CONFIG_BACKLIGHT_PWM=y to your .config 
> (and make sure it stays that way after a "make oldconfig"). 
>
>
> Ok kernel with pwm_backligth leave on backlight, now i must turn on VUSB 
for OTG , uboot 
turn otg vbus on kernel NOT(switch off).

Re: [linux-sunxi] Re: [PATCH 0/5] ARM: dts: sunxi: Add backlight node to q8 tablets

[8001010]

Hans de Goede wrote:
> Hi,
>
> On 21-12-15 11:56, Silvio Pellicano wrote:
>>
>>
>>> Here is a slightly updated version of Chen-Yu's backlight
>>> patches, also adding support for the backlight found on A13
>>> based q8 tablets.
>>>
>>
>> If i compile your dtsi with (obviously) pwm  support enable , backlight
>> switch off after kernel start,
>> if i disable pwm in menuconfig,it stay on, all seem correct (pwm on PB2 in
>> original script.bin),
>> but there is somewhere a bug in pwm or dtsi description of backlight.
>
> No there is not, if you enable the pwm driver you must also enable
> the backlight-pwm driver / add CONFIG_BACKLIGHT_PWM=y to your .config
> (and make sure it stays that way after a "make oldconfig").
>
> Regards,
>
> Hans
>
Now work, but what flag  i have to enable to leave 5v usb otg ON?
uboot switch ON Usb Otg voltage but kernel switch off during boot (no usb devices work).

Thanks

[linux-sunxi] Re: [PATCH 0/5] ARM: dts: sunxi: Add backlight node to q8 tablets

[8001010]

Hans de Goede wrote:
> Hi,
>
> On 21-12-15 11:56, Silvio Pellicano wrote:
>>
>>
>>> Here is a slightly updated version of Chen-Yu's backlight
>>> patches, also adding support for the backlight found on A13
>>> based q8 tablets.
>>>
>>
>> If i compile your dtsi with (obviously) pwm  support enable , backlight
>> switch off after kernel start,
>> if i disable pwm in menuconfig,it stay on, all seem correct (pwm on PB2 in
>> original script.bin),
>> but there is somewhere a bug in pwm or dtsi description of backlight.
>
> No there is not, if you enable the pwm driver you must also enable
> the backlight-pwm driver / add CONFIG_BACKLIGHT_PWM=y to your .config
> (and make sure it stays that way after a "make oldconfig").
>
> Regards,
>
> Hans
>
Now work, but what flag  i have to enable to leave 5v usb otg ON?
uboot switch ON Usb Otg voltage but kernel switch off during boot (no usb devices work).

Thanks

Re: Re: [PATCH 0/5] ARM: dts: sunxi: Add backlight node to q8 tablets

[Hans de Goede]

Hi,

On 11-01-16 11:34, 8001010 wrote:
> Hans de Goede wrote:
>> Hi,
>>
>> On 21-12-15 11:56, Silvio Pellicano wrote:
>>>
>>>
>>>> Here is a slightly updated version of Chen-Yu's backlight
>>>> patches, also adding support for the backlight found on A13
>>>> based q8 tablets.
>>>>
>>>
>>> If i compile your dtsi with (obviously) pwm  support enable , backlight
>>> switch off after kernel start,
>>> if i disable pwm in menuconfig,it stay on, all seem correct (pwm on PB2 in
>>> original script.bin),
>>> but there is somewhere a bug in pwm or dtsi description of backlight.
>>
>> No there is not, if you enable the pwm driver you must also enable
>> the backlight-pwm driver / add CONFIG_BACKLIGHT_PWM=y to your .config
>> (and make sure it stays that way after a "make oldconfig").
>>
>> Regards,
>>
>> Hans
>>
> Now work, but what flag  i have to enable to leave 5v usb otg ON?
> uboot switch ON Usb Otg voltage but kernel switch off during boot (no usb devices work).

In order for otg to work you must load a gadget driver, e.g. do:

insmod libcomposite.ko
insmod u_serial.ko
insmod usb_f_acm.ko
insmod g_serial.ko

Regards,

Hans

[linux-sunxi] Re: [PATCH 0/5] ARM: dts: sunxi: Add backlight node to q8 tablets

[Hans de Goede]

Hi,

On 11-01-16 11:34, 8001010 wrote:
> Hans de Goede wrote:
>> Hi,
>>
>> On 21-12-15 11:56, Silvio Pellicano wrote:
>>>
>>>
>>>> Here is a slightly updated version of Chen-Yu's backlight
>>>> patches, also adding support for the backlight found on A13
>>>> based q8 tablets.
>>>>
>>>
>>> If i compile your dtsi with (obviously) pwm  support enable , backlight
>>> switch off after kernel start,
>>> if i disable pwm in menuconfig,it stay on, all seem correct (pwm on PB2 in
>>> original script.bin),
>>> but there is somewhere a bug in pwm or dtsi description of backlight.
>>
>> No there is not, if you enable the pwm driver you must also enable
>> the backlight-pwm driver / add CONFIG_BACKLIGHT_PWM=y to your .config
>> (and make sure it stays that way after a "make oldconfig").
>>
>> Regards,
>>
>> Hans
>>
> Now work, but what flag  i have to enable to leave 5v usb otg ON?
> uboot switch ON Usb Otg voltage but kernel switch off during boot (no usb devices work).

In order for otg to work you must load a gadget driver, e.g. do:

insmod libcomposite.ko
insmod u_serial.ko
insmod usb_f_acm.ko
insmod g_serial.ko

Regards,

Hans